Indian Army Tender
If you want to inquire about any e-tender the Punjab government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Punjab tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Punjab etender you're looking for. Read further to learn how to search and bid for etender Punjab.
Costs
EMD
₹ 3,20,000Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2019_IHQ_458526_1Tender No
320/QTN/PTK/2019-20/04/OPWTender Authority
Indian Army ViewPurchaser Address
-Website
http://https://www.indianarmy.nic.in/home
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Corner Clamp to be used when fence line has corners / turns These clamps are used to fix the mesh on the poles by using Cody Clamp and suitable fasteners.Material for Corner clamp: MS flat 35 mm width and 3 Mm thick, as per IS 1730 Coating: Pre-galvanised material with min 270 GSM. After fabrication the clamps are powder coated with RAL 6005 green Colour to 60-80 Mircons. Weight of each Corner Clamp: 0.35 Kg +/-10%
(Type Test Certificate as above to be provided by the bidder).
Refer Sketch att 'R'
MAKE : A ONE FENCE PRODUCT/SG ENTERPRISES/SLING SHOT/GLOBAL TECHNOCRAFT
420
-
-
Cody clamp: Corner Clamp to be used when fence line has corners / turns These clamps are used to fix the mesh on the poles by using Cody Clamp and suitable fasteners.
Material for Cody clamp: MS flat 32.5 mm width and 2.8 Mm thick, as per IS 1730
Coating: Pre-galvanised material with min 270 GSM. After fabrication the clamps are powder coated with RAL 6005 green Colour to 60-80 Mircons.
(Type Test Certificate as above to be provided by the bidder).
Weight of each Cody Clamp: 0.05 Kg +/-10% MAKE : A ONE FENCE PRODUCT/SG ENTERPRISES/SLING SHOT/GLOBAL ECHNOCRAFT
840
-
-
Mush room Head Bolts with security nuts:( fixing accessories for fixing omega clamp & corner clamp)
Each Omega clamp & Corner Clamp shall be supplied with two sets mush room headed bolts with security nuts and washers.
Material: SS 304
Size: M8 X 60 mm
12320
-
-
IP Binder (Flat clamps) for panel connection: Material: MS Flat 25x3, 160mm long, with 2-slots – as per IS 1730
Coating: Pre-galvanised material with min 270 GSM. After fabrication this will be powder coated in RAL 6005 to 60-80 microns.(Type Test Certificate as above to be provided by the bidder).
Weight / set: 0.2 Kg +/-10% Refer Sketch att 'P' MAKE : A ONE FENCE PRODUCT/SG ENTERPRISES/SLING SHOT/GLOBAL TECHNOCRAFT
3200
-
-
M8x35 Mushroom Head bolt with breakable head nut ( for fixing the IP binder with weld mesh panels)
Material: SS 304
Size: M8X35 Weight: 0.025 Kg +/- 10%
6400
-
-
Fence Post:
Type: Circular Hollow section.
Specification: IS 1161-2014 (Medium Grade)
Outer Diameter: 76.1 mm +/- 1 %
Thickness: 3.6 mm +/- 10% (Medium Grade)
Length: 3345 mm +/- 2%
Weight / mtr: 6.44 Kgs, +/- 10%
Coating: Hot dip galvanised with minimum 360 GSM coating, as per IS 4736
Uniformity of Coating: As per IS 2629
Adhesion test for coating: As per IS 6745 / IS 2629
Refer Sketch att 'P'
MAKE : A ONE FENCE PRODUCT/SG ENTERPRISES/SLING SHOT/GLOBAL TECHNOCRAFT
800
-
-
Straining Y Arm and fitting accessories:
i. Straining Y Arm:
Straining Y-Arm for supporting top PTCC:
Material: MS Angle Size : 50x50x5mm as per IS 1852
Coating: Hot dip galvanised to min 460 GSM as per IS 4759 / IS 2629.
Uniformity of Coating: As per IS 2629
Adhesion test for coating: As per IS 6745 / IS 2629
Weight: 6.6 Kgs+/- 10%
Length of 1 Arm is 750 mm, 120 degree angle of Y, Outer diameter 63mm of sleeve
Cap and manufactured as per Refer Sketch att 'P' & 'S'
1 straining Y arm will be installed at every 30 meters.
MAKE : A ONE FENCE PRODUCT/SG ENTERPRISES/SLING SHOT/GLOBAL TECHNOCRAFT
68
-
-
Fitting accessory for Straining Y arm:
Mush room Head Bolts with breakable head security nuts: Each Y arm shall be supplied with two sets mush room headed bolts with security nuts and washers.
Material : SS 304
Size: M8 X 120 mm
128
-
-
Eye Bolt for Straining Y arm:
Each Y arm shall be supplied with 6 sets of Eye bolts with security nuts and washers.
Material: SS 304 Size: M8 X 100 mm
Weight : Eye bolt , Nut and washer: 0.1 Kg +/- 10% ; Refer Sketch att 'T'
408
-
-
Intermediate Y Arm and fitting accessories:
Intermediate Y Arm:
Intermediate Y-Arm for supporting top PTCC:
Material: MS Angle Size : 50x50x3mm as per IS 1852
Coating: Hot dip galvanised to min 460 GSM as per IS 4759 / IS 2629.
Uniformity of Coating: As per IS 2629
Adhesion test for coating: As per IS 6745 / IS 2629
Weight: 3.7 Kgs+/- 10%
Length of 1 Arm is 750 mm, 120 degree angle of Y, with a support steel strip of 25 X5 mm (galvanised as per IS 4759).
1 intermediate Y arm will be installed at every post except the posts with Straining Y arms.
Refer Sketch att 'U'
MAKE : A ONE FENCE PRODUCT/SG ENTERPRISES/SLING SHOT/GLOBAL TECHNOCRAFT
732
-
-
Fitting accessory for Intermediate Y arm:
Mush room Head Bolts with breakable head security nuts: Each Y arm shall be supplied with two sets mush room headed bolts with security nuts and washers.
Material : SS 304
Size: M8 X 120 mm
1440
-
-
Concertina coil:1050 mm dia/56 Loops/2.5mm Core wire, Coil Diameter: 1050mm +/- 50 mm
Galvanised steel Strip: (As per IS 277)
Width 16 MM +/- 0.05 mm, Thickness: 0.47 mm +/- 0.02 mm, Zinc Coating: 275 GSM minimum
Core Wire High carbon spring steel (as per IS 280) Diameter: 2.5 MM +/- 0.05 mm
Zinc Coating on wire: Minimum 275GSM (As per IS 4826 /IS 6745-1972 reaffirmed 2006).
Tensile Strength of wire: Not less than 1500 N/sq.mm
Weight of coil: Not less than 14.50 Kg. Number of loops: 56,
Stretchable length of coil: 12 mtr. Refer Sketch att 'P'
MAKE : A ONE FENCE PRODUCT/SG ENTERPRISES/SLING SHOT/GLOBAL TECHNOCRAFT
168
-
-
High Tensile Barbed Wire:
High Tensile Barbed wire uses a single High tensile wire as the core wire instead of the two twisted low tensile wires, offering very high resistance to cutting attempts.
High tensile heavy Galvanised mild steel wire for Line wire and High tensile
barb wire is made of higher carbon steel approximately 0.28%.
Specification of Line wire- Diameter: 3.15 +/- 0.05 mm
Coating : Zinc Coating 240 GSM as per IS 4826
Tensile strength: 1450-1650N/Sqmm. All as per IS 432-2, Specification of Barbwire
Diameter: 2mm +/- 0.02 mm Coating: Zinc coating 240GSM,
Tensile Strength: 450-600 N/Sqmm, Barbing Pitch:100mm Barb Type: 4 point IOWA Style, Strands: Single (6 Row) Weight of Barbed wire per mtr : Not less than 106 gms/mtr
Refer Sketch att 'P' MAKE : A ONE FENCE PRODUCT/SG ENTERPRISES/SLING SHOT/GLOBAL TECHNOCRAFT
12600
-
-
Hog rings are used to secure the concertina coil to the barbed wire and also to secure consecutive concertina coils. Hog ring plier is the tool used to crimp the hogrings and close them securely. Material: SS 304
Dia: 3mm
Weight: 0.005 Kg +/-8% MAKE : A ONE FENCE PRODUCT/SG ENTERPRISES/SLING SHOT/GLOBAL TECHNOCRAFT
17056
-
-
Anchor Rod : 10 mm dia, 250mm long GI Rod is tied with fence post at bottom using tie wire ( 2 Nos ) 600mm length &dia 1.4mm (2 Nos for each post) Refer Sketch att 'P'
MAKE : A ONE FENCE PRODUCT/SG ENTERPRISES/SLING SHOT/GLOBAL TECHNOCRAFT
1600
-
-
Construction material
-
-
-
Ordinary Portland Cement OPC Grade 43, IS-12269-1990, packed in 50 Kgs HDPE bags conforming to IS 11652/2000 (Make – AMBUJA/ACC/JK)
1286
-
-
Coarse Sand Sand shall be clean, sharp, angular hard and durable free from adherent coating and shall not contain clay, mica and other impurities. The maximum quantities of clay and fine silt in sand shall not be more than 5% by mass as per IS-383-1970.
142
-
-
20mm Stone Aggregates Stone aggregate shall be crushed stone 20mm graded conforming to IS-383 -1970 and shall be clean hard tough, durable and of uniform quality throughout. The aggregate shall be free from soft disintegrated materials, vegetable and other organic impurities.
168
-
-
40mm Stone Aggregates Stone aggregate shall be crushed stone 40mm graded conforming to IS-383 -1970 and shall be clean hard tough, durable and of uniform quality throughout. The aggregate shall be free from soft disintegrated materials, vegetable and other organic impurities.
72
-
-
Labour :-
-
-
-
Skilled Labours (4 Men Per day)
40
-
-
Unskilled Labours (8Men Per day )
40
-
-
Hiring of JCB (8 Hours Daily)
8
-
-
Hiring of Concrete mixer
20
-
-
Erection tools
-
-
-
Hog ring plier Manual Hog plier (C-Ring Hand pliers)
1
-
-
Ring Spanner 12/13 (Make-Taparia/Estmon/Pie)
2
-
-
Round Nose shovel with handle of overall length with handle 990mm and min wt 1.6kg-TATA
3
-
-
Crow bar chisel 1650mm long 32mm dia weight not less than 10 kgs-Tata
2
-
-
Rachet 1/2" Single Spanner (Make: Taparia/Hira/Bosh)
2
-
-
Hand Gloves superior quality with pseude leather and woolen inner lining and double patch on pads. Make : Hex armor ISI Marked as per sample
15
-
-
Rubber Mallet
2
-
-
T- Spanner with long handle with comfortable rubber grip, Long rod for deep work. (Hex size 13mm) (Make-Taparia/Estmon/Pie)
3
-
-
Wire cutter 125mm long (Make-Taparia)
2
-
-
Bolt cutter 18" (350mm) (Make: Taparia/Hira)
2
-
-
Bolt cutter 24" (600mm) (Make: Taparia/Hira)
2
-
-
Hammer 1 Kg (Make-Taparia)
1
-
-
Nylon rope 20mm dia
20
-
-
Plumb-bob with brass measuring tools 200 gms, including cotton line material length 1 Mtr and removable steel cap
2
-
-
Water Storage Tank Cylindrical, vertical, rotational moulded polythylene with close top, Capacity 500 Ltrs conforming to IS - 127011996, Make : Sintex IS marked
1
-
-
Jerrican 20 Ltr Capacity PVC
2
-
-
Aluminium Bucket 12 Ltr
2
-
-
Mug Aluminium Bucket 1 Ltr
2
-
-
Chain saw 16" Electronic wood cutter
1
-
-
Tape measuring with 5 Mtr Make : Freemans
1
-
-
Tape measuring with 50 Mtr Make : Freemans
1
-
-
Niddle Vibrator Machine (Petrol) Make : Greeves/Trister
1
-
-
Side cutting pliers insulated with thick C.A sleeve length 2.5mm confirming to IS 4378-1990 Make : Taparia
2
-
-
Nails
2
-
-
Double point end pick axes head 3 kg with handle of size 255mm Make: Tata
2
-
-
Pan motor for carrying earth 1:4 Kgs to 1:6 Kgs Make : TATA
4
-
-
Plaster Trowel with wooden handle ISI Marked
4
-
-
Chisel 12" 40mm Make : Taparia
1
-
-
HDPE circular water level 1/2" to 1" Unit length 6Mtr
2
-
-
Wind lashing stick
6
-
-
Safety helmet
4
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements