Military Engineer Services Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 15,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2020_MES_405460_4Bid Award Id
ViewTender No
NIT No . 8001/270/01/E8 OF 2020-2021Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
M&L high strength deformed TMT steel bars, as in reinforcement, 10 mm dia and over, cut to length, bent to shape required, including cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed by Engineer-in-charge.
35
-
-
Material and labour for Brickwork with old size sub class locally available bricks, having compressive strength 75Kg/sqcm, straight or curved on plan excd 6 M mean radius in built in cement and sand mortar 1:6 complete all as specified and directed by Engineer-in-charge.
0.5
-
-
M&L for broken stone as Hard core of gauge n exc. 63 mm , deposited , spread and levelled in layer n exc. 150 mm thick, watered and rammed to a true surface. complete all as specified and directed by Engineer-in-charge.
2.7
-
-
Demolition of cement concrete (unreinforced) in ground floors and paving of any description not exc 15 cm thickness (below or above GL) including removing materials obtained from demolition from worksite outside MD land any distance complete all as specified and directed by Engineer-in-charge.
11.25
-
-
M&L Plain cement concrete type C1 (1:3:6), using 75 mm thick (using 40mm graded stone aggregate) for plinth protection, pathway and surface finished even and smooth without using extra cement. complete all as specified and directed by Engineer-in-charge.
150
-
-
Material and labour for rendering 15 mm thick in CM 1:6 on fair faces of brick / concrete surfaces finished fair and even without using extra cement internal wall surfaces complete all as specified and directed by Engineer-in-charge.
3
-
-
Material and labour for preparation of new plastered or unplastered surafces of fencing post and applying three coats of white wash complete all as specified and directed by Engineer-in-charge.
3
-
-
Taking down shutters of any description exc 1 sq.m and n exc 2 sq.m each and refixing in the same opening after rescuring / easing complete all as specified and directed by Engineer-in-charge.
8
-
-
Material and labour for preparation of new steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint (1st quality) over one coat of red oxide primer complete all as specified and directed by Engineer-in-charge.
30
-
-
Supply, fabricating and fixing rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces,etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening .grade Fe-410-W ( Gde-E-250) quality -B complete all as specified and directed by Engineer-in-charge.
280
-
-
Supply and fixed Mild steel, plain, black sheet 1.60 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws , clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with rivetted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed by Engineer-in-charge.
0.8
-
-
Taking down cement plaster on brick or stone walls etc. including racking out joints, hacking for key, scrubbing down with water, any description etc.including removing of rubbished material from work site complete all as specified and directed by Engineer-in-charge.
15
-
-
Material and labour for vitrified ceramic (square/rectangular) light coloured polished tiles of thickness 10mm, (1st quality) area of each tiles exceeding 0.18 sqm but not exc 0.36 sqm and , in floors etc. set and jointed in neat cement slurry and pointed in white cement and pigment to match over 20 mm thick screeding in CM 1:6 complete all as specified and directed by Engineer-in-charge. ( Note: Screed bed shall also deemed to be included in the quoted rate by the contractor.)
80
-
-
Material and labour for Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but nexc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match etc over and including screed bed or bedding layer 20 mm thick in cement morter 1:6 for laying tiles complete all as specified and directed by Engineer-in-charge.
( Note: Screed bed shall also deemed to be included in the quoted rate by the contractor.)
275
-
-
Material and labour for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust , etc. and brushing neat cement slurry with 3.0 Kg of cement per sq. metre complete all as specified and directed by Engineer-in-charge.
340
-
-
Material and labour laying well burnt old size bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection all as specified.
-
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements