Indo Tibetan Border Police Tender

Supplying and filling in plinth with Local sand under floors including, watering, ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level 1:5:10 (1 Cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) cement brand will be ACC, CCI, Ambuja, JP, Bangar, Birla Plus, L&T (including septick tank qty)

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) cement brand will be ACC, CCI, Ambuja, JP, Bangar, Birla Plus, L&T (including septick tank qty)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75 mm bed by dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with : Cement mortar 1:6 (1 Cement : 6 coarse sand)(including septick tank qty)

Random rubble masonry with hard stone in supersturucture above plinth level and upto floor level i/c levelling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with : Cement mortar 1:6 (1 Cement : 6 coarse sand)(including septick tank qty)

Providing and laying demp proof course 40mm thick with cement concrete 1:2:4( 1 Cement: 2 Coarse sand: 4 Stone aggregate 12.5mm hand brocken)

Providing and fixing up to floor V level precast cement concrete solid block incl. hoisting and setting in position with cement mortar 1:3(1cement : 3 coarse sand ), cost of required centering shutturing and finishing smooth with 6 mm thick cement plaster 1:3(1cement : 3 coarse sand )on exposed surface complete. Cement Ordinary portland 43 grade conforming to IS No: 8112- 1989 brand like CCI, ACC, Ultratech, Vinay, Star, JP, Ambuja, Binani only. 1:3:6 (1 Cement :3 coarse sand: 6 stone agregate 20mm nominal size)

Centering and shutturing incl. strutting, proping etc and removal of form work for Lintal, beam, plinth beam, girders bressumers and cantilevers, slab, columns

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upto floor five level excluding cost of centring, shuttering,with 1:2:4 (1 Cement : 2 coarse sand: 4 graded stone aggregate 20 mm River single/Hand brocken) for RCC Pillars . Cement Ordinary portland 43 grade conforming to IS No: 8112- 1989 brand like ACC, Ultratech, Vinay, Star, JP or equivalent brand as approved by Engineer in charge

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete . MS Bar deformed TMT bars , conforming to IS 1786-1985 of make Tata, Amba, Tiscon, Paras , Rhino Thermo-Mechanically Treated Thermo-Mechanically Treated / cold twested bars

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position- with First class wood (surai/ kail/assam teak/ hollock) Local wood

Steel work in built up tubular trusses including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete.Hot finished welded type tubes

Providing and fixing panelled or panelled and glazed shutters doors, windows and clerestory windows including ISI marked black enameled M.S. butt hinges with necessary screws (screws should be of stainlesss steel and brand Magnum/ Nettlefold/Amul) excluding, panelling which will be paid for seperately (Thickness of shutters should be 35mm) - first class local wood(surai/ kail/assam teak/ hollock) conferming IS- 399:1963 (Weight of should be 545 Kg/ M3) Note- The shutters should be conferming IS 1003 (Part-2): 1994 Local wood conferming I:S-399:1963 (Weight of wood should be 545Kg. Per Cum. 35 mm thick shutterrs

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25mm to 40mm thick- First class local wood (surai/ kail/assam teak) (i)Local wood panells should be fixed only with grooves but additional beading should be provided on both sides,stiles, rails and panels in door shutters shall be of the same species of timber. (ii) Lock rail of door shutters shall be so placed that its centerline is at a height of 850+ 55mm from the bottom of shutters, each door shutters shall be fixed to the frame with three hinges one at the center and other two at 200 mm from top and the bottom of the shutters (iii) All door shutters shall be finished smooth with well planed faces and panels of shutters shall be flat and well sanded to a smooth and level surface. (Iv) In case of double leaved shutters the meeting of the stiles shall be rebated either splayed or square type. (V) Each window shutters shall be fixed to the frame with two hinges so that bottom hinge is at 15 Cm from the lower end of shutter and upper hinge is at 10 CM from the upper end of the shutters (vi) Ventilator shutters to be fixed to its frame with two hinges at quarter points or top rail. Local wood (surai/ kail/assam teak/ hollock) conferming I:S-399:1963(Weight of wood should be 640 Kg. Per Cum.

Providing and fixing glazed shutters for door, window and ventilators using 4mm thick float glass pans of brand Modi float, Atul, Saint Gobain, golden only. Weight of glass pan should be 10.00 kg/sqm. Including black enamelled ISI mark Butt hinges with nessessury screws.(screws should be of stainlesss steel and brand Magnum/ Nettlefold/Amul) First class local wood(surai/ kail/assam teak/ hollock)-35mm thick 35 mm thick shutterrs

Providing and fixing 35 mm thick wire gauge shutters using galvanized MS wire gauge of avarage width of aperture 1.4mm with wire of dia 0.83mm for door, window and ventilator Including black enamelled ISI mark Butt hinges with nessessury screws.(screws should be of stainlesss steel and brand Magnum/ Nettlefold/Amul) First class local wood (surai/ kail/assam teak/ Hollock)-35mm thick

Providing wood work in frames of false ceiling, partition and other frames fixed in position- with First class local wood (surai/ kail/assam teak/ Hollock) First class local wood (surai/ kail/assam teak)

Providing and fixing wood plain linning tongud and grooved on and including wooden plug complete with necessary screw, priming coat on unexposed surface. (with 6 mm thick ply wood)

P/f wooden beading with iron screws and priming coat on unexposed surface complete. First class local wood (surai/ kail/assam teak/ Hollock)-5.x12mm

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm

Providing and fixing Anodized Allum Tower Bolt 200x10mm conforming to IS 204 of brand conforming to IS 2681-1979 of brand Classic/EPSA ISI/Décor/Venus /Adersh /crown ( anodic coating not less than grade AC 10 as per IS : 1868 ) 100x10mm

Providing and fixing Anodized Allum Handles 125mm IS 208 of brand Classic/EPSA ISI/Décor/Venus /Adersh /crown ( anodic coating not less than grade AC 10 as per IS : 1868 ) size 125 mm

Providing and fixing precoated galvanized iron profile sheets 0.50mm(+.05%) total coated thickness with zinc coating 120 gm per sqmtes as per IS:277, in 240 mpa steel grade 5-7 micron epoxy primer on both sides of the sheets and polyester top coat 15-18 microns. steel should have protective gaurd film of 25 micron minimum to avoid scratches during transporatation and should be supplied in single length up to 12 mtrs or as directed by engineer in charge. The sheet shell be fixed by using self drilling / self tapping scerww of size 5.5x55 mm with EPDM seal complete up to any pitch in horizontal/ vertical or curved surface, excluding cost of perlis, rafters,trusess etc. including cutting to size and shape wherever required. GS sheet will be brand TATA, SAIL, or equivalent

Providing and fixing precoated galvanized iron profile sheets 0.50mm(+.05%) total coated thickness with zinc coating 120 gm per sqmtes as per IS:277, in 240 mpa steel grade 5-7 micron epoxy primer on both sides of the sheets and polyester top coat 15-18 microns using self drilling / self tapping scerww of size 5.5x55 mm ridge plain 500-600 mm

Extra for providing and fixing wind ties of 40x 6 mm flat iron section

Providing and fixing GI pipe midium class make TATA, Jimdal Hissar, JST, Surya with GI fitting of Unik and intillo techsupport clamp U-clamp of size 23x1x2.5mm of chilly incl. cutting and making good the walls etc ( Internal work) Exposed on wall 15 mm dia nominal bore.

Providing and fixing CP brass bib cock 15 mm dia of make Parko/Kingstone/Essco confirming to IS:8931

Providing and fixing CP brass stop cock 15 mm dia ( concealed) of make Parko/Kingstone/Essco confirming to IS:8931

Providing and fixing water closet squatting pan ( Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, Parryware/Hindware/Seabird/Orient (Coral) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan.of size 580x440mm with integral type foot rests

Providing and fixing wash basin of make Hindware, Perryware, Cera standerd quality size 550x400mm with CI/MS bracket, 15 mm CP brass piller tape , L&K,, Kingston, Renutrol, Hansa, 32mm CP brass waist of L&K,, Kingston, Renutrol, Hansa, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing mirror of superior glass of approved quality with plastic moulded frame of approved make and shade with 6mm thick hard board backing. Rectanguler shape 600x450mm

Providing and fixing soil waste and vent pipes 100 mm dia of brand RIF, SRIF, NECO 100 mm dia PVC socketed pipe as per ISI make

Constructing Stone masonry man holes in cement mortar 1:4 (1 cement:4 coarse sand) RCC top slab with 1:2:4 (1cement: 2 coarse sand: 4 stone aggregate 20mm nominal size) foundation concrete 1:2:4 (1cement: 4 coarse sand: 8 stone aggregate 40mm nominal size) mix, inside plastering 12mm thick with cement mortar 1:3 (1 cement:3 coarse sand) finished with floating coat of neat cement and making a channels in cemnt concrete 1:2:4 (1cement: 2 coarse sand: 4 stone aggregate 20mm nominal size) finished with as floaating coat of neat cement as per standard design. Cement brand CCI, ACC, Ultratech, Vinay, Star, JP, Ambuja, Binani only. Inside size 90x80x45 cm including CI cover with frame 455x610 mm internal diamensions total weight of and frame to be not less then 38kg ( weight of cover 23 kg and weight of frame 15kg)s with FPS bricks (PCC block) with class designation 75

Constructing masonry chember for u/g CI inspection chember with stone work in cement mortar 1:4 (1 cement:4 coarse sand) CI cover and frame 455x610 mm internal diimensions and weight not lessthen 38.00kg( weight of cover 23 kg and weight of frame 15kg) RCC top slab with 1:2:4 (1cement: 2 coarse sand: 4 stone aggregate 20mm nominal size) foundation concrete 1:5:10 (1cement: 5coarse sand: 10stone aggregate 40mm nominal size) mix, inside plastering 12mm thick with cement mortar 1:3 (1 cement:3 coarse sand) finished with floating coat of neat cement and making a channels in cemnt concrete 1:2:4 (1cement: 2 coarse sand: 4 stone aggregate 20mm nominal size) finished with as floaating coat of neat cement as per standard designCement brand CCI, ACC, Ultratech, Vinay, Star, JP, Ambuja, Binani only. Inside diimensions 455x610 and depth 45 cm for pipe line with one or two inlets.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75/stones and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With F.P.S. bricks/stone (PCC block)

Providing and applying plastering on walls 12 mm thick of mix 1:6 ( 1cement :6 coarse sand)(including septick tank qty)

pointing on stone work with cement mortar 1:3 (1 Cement : 3 fine send) : Raised and cut pointing.

Finishing walls with acrylic smooth exterior paint of APEX, Asian, Berger, Nerolac, Shalimar of required shade on new work two or more coats applied @ 1.67 ltrs/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10 sqm.

Distempering with oil bound distemper of shalimar/ Berger/ Johnson & Nicolson (two or more coats) of required shede onnew work, over and i/c water thinnable priming coat to give an even shade.

Applyinig priming coat: with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard & soft wood)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

Cement concrete flooring 1:2:4 ( 1 cement: 2course sand: 4 graded stone agregate) finished with a neet cement floating coat, incl. Cemnt slurry, but excluding the cost of noising of steps etc complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such black laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license ].

ELECTRIFICATION

Copper Point Wiring in PVC condute ( PVC condute shell be of suprime brand) wiring for light point/ fanpoint/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated, copper conductor cable make L&T, Rallision, Hevells, in surface/ recessed PVC conduit as required with specification like maximum 4 nos of wires in one conduit to 20m m dia , green/ yellow copper earth wire to come to swich box , black insulated copper wire for neutral also to come to swich box and for one core cable red PVC insulated copper should be used whereas for two core cable red and blue PVC wire to be used, including gang box of required way with 5 amp switch socket PVC conduit should be fixed with respective size of Intillo Tech Support clamp of chilly fixed with screw of make Nettle fold/ Amul/ Magnum. Group A

Copper cercuit/submain wiring in PVC condute ( PVC condute shell be of suprime brand) wiring for submain wiring with 2x2.5 mm² FRLS PVC insulated copper conductor , single core cable make L&T/Rallison/havells in recessed steel conduit as required with specifications like maximum 4 nos of wires in one conduit of 20 ,mm dia, green/yellow insulated copper earth wire to come to shich box, black insulated copper wire for nutral also to come to shich box and and for one core cable red PVC insulated copper wire should be used whereas two core cable red and blue PVC copper wire to be used , steel conduit should be fixed with respective size of Intello Tech support clamp of chilly fixed with screw of make Nettle fold/ Amul/ Magnum

Supply and fixing following rating double pole 240 volts, isolator in the existing MCB DB complete with connection, testing and commissioning etc. as required of brand Havells, Indocopp, Standerd, L&T 40 AMP