Urban Improvement Trust Tender

Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. . OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR Single pole MCB 6 A to 32 A rating

Double pole MCB 6 A to 32 A rating

Providing & Fixing of of ISO certified company made Multiple socket with surge and spikes protection cartridge not less then 5 KV as per PWD specification for electrical Works with minimum four nos. universal 6 A sockets, one 6 A switch and 3 pin company fitted plug top and 3 core multistrand copper lead minimum 1.5 mtr. including making connection etc as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR

Providing & Fixing of energy efficient direct fit (Retrofit) Polycarbonate/ Glass housingSMD Mid Power LED tube rod (with integral driver & alumn. heat sink ), on existing fixture.system lumen efficacy ≥ 100 lm/Watt output, internal surge protection of 2.5 KV ,THD 20% ,p.f.≥0.95,CRI 80 , life time of minimum 35000 Burning Hours with , 70% of intialLumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As perANSI Bin) , maximum power consumption should not more than the specified rating andFixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures WordMark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own inhouse NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80)certificate /Report from OEM shall be submitted. All as per pre approved by Engineer in charge. Foradditional technical parameters of products/ work , refer Annexure "A" attached with thisBSR . 1200mm , Min. Lumens output 2000 lm LED Tube rod with Polycarbonate Housing

Providing & Fixing of IP 20 box made out from 1.2mm thick CRCA sheet steel with depth of minimun 30 mm and finished with powder coating and suitable for mounting LED tube including side covers, holders , internal wiring to illuminate the single sided connection LED tube. ( Without tube). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . Suitable for 4' LED Tube shape fixture for single rod

Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathedArmoured aluminium cable of 1.1 KV grade as per PWD specification for electrical Works in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:- (a) Material :- H4- Grade aluminium conductor of purity 99.6 % & as per IS:1554 P-I / IS :7098 P - I (b) conductor shall have electrolytic aluminium confirming to IS 8130, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures . (c) OEM Must have ISO 9001 & 14001 certifications for quality assuarance & its own in house NABL lab setup for all testing facilities for cables . Appropriate type test certificate / OEM test report shall be submitted . All above as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 25 sq.mm 3.5 core

10 sq.mm 2 core

16 Sq.mm 3.5 Core

Providing experienced and Highly skilled/skilled/ semi-skilled/Un Skilled labour for electric repair/ maintenance / operation of Air conditioning/Air cooling/Fire fighting/Lift/DG set/CCTV/EPABX or any otherelectromechanical systems as per requirement (one shift of 8 Hrs per day for26 Working Days in a month) Highly skilled Labour

Add for extra working on Holidays. Highly skilled Labour

Providing & Fixing of IK07 IP-66 protected high power LED flood lightsystem with Pressure diecast aluminium housing LM6/ ADC12material , toughened glass diffuser with suitable lenses on LED toachieve various beam angles, 240 volt, 50Hz, of high power LED lamps. Integrated driver must be potted & has a unique BIS R number shallbe high efficiency having efficiency more than 85 % and in complianceto BIS certified and T.C. certificate. The System level Luminaire efficacy=120 lm/ wt with High Power LEDs is to be used . LED driver InputVoltage AC 120 to 270 V AC with High voltage Cutoff @=300 V AC andAuto resetting Safety . Input Frequency 50Hz±3%, Power Factor 0.95,driver Efficiency 85% , THD(I) 10% , driver current 1000mAshown in LM79 report. driver should be Phase to phase protection of440 V for 4 Hrs. Electrical Connector Must be provided, SurgeProtection Min =4KV internal and 10KV external, System life of 30000Burning hours with 70% of Initial Lumens maintained, color RenderingIndex 70 and CCT 5700K ±355K. Driver current 1000mA shown inLM79 report. Manufactures Word rk /Name Engraved/ Embossing/ Screen printing on die cast housing to lowtraceability/authenticity. Fixture shall be IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testingfacilities for LED fixtures. (LM79/LM80) Certificate/ report withliable warranty of Product/ accessories from OEM shall be submitted . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A"attached with this BSR . High Power LED Flood Light Minimum lumen output 14800 lm

High Power LED Flood Light Minimum lumen output 18650 lm

Providing & Fixing of IK07 IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum LM6/ ADC12 material with heat dissipation fins on housing with UV stabilized PC/Toughened Glass cover (UV stablzation report submitted for UV cover ) and secondary lens on each LED & should be SMD type . The System level Luminaire efficacy =120 lm/ wt with High Power LEDs is to be used and potted driver must be potted & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @=300 V AC and Auto resetting Safety ,Input Frequency 50Hz±3% Power Factor 0.95 driver Efficiency 85% ,THD(I) 70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced. OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR LED Street Light fixture with Minimum lumen output 12500 lm

Supply and erection of Galvanized Iron pole with galvanizing done in single dipping (Average coatingthickness Minimum 65 Microns) continuously tapered poles having Octagonal / Circular cross-sectionsdesigned to withstand the maximum wind speed as per IS 875, The pole shaft shall be made from sheetsteel (HT Steel Conforming to grade S355JO) and confirming to BSEN 10025 and shall be continuouslytapered with single longitudinal welding. There shall not be any circumferential welding. The welding ofpole shaft shall be done by Submerged Arc Welding (SAW) process. pole shafts shall be provided with therigid flange plate of suitable thickness (Fe 410 conforming to IS 226 / IS 2062) with provision for fixing 4no. foundation bolts, This base plate shall be fillet welded to the pole shaft at two locations i.e. frominside and outside.The octagonal Poles shall have lockable door of approximate 500 mm length at theelevation of 500 mm from the Base plate with bakelite sheet having 6A SP MCB and 16 sqmm stud typeconnector ( 4 nos) inside the pole at door opening for cable connection of following length and dimension as per table P-01 with base plate and foundation bolt on the Existing cement concrete foundation.All asper pre approved by Engineer in charge. For additional technical parameters of products/ work , referAnnexure "A" attached with this BSR 9 Mtr.

Supply, Erection and Fixing of hot dipped galvanised M.S. Overhang (48.3 X 3.25 mm) with cap (400 x 88.9 / 114.3 x 3.25 mm) over the existing poles. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR Double arm overhang

Drawing attach at Table P-4 with Following Procedure & All as per pre approved by Engineer in charge.For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .A) Excavation of Pit for Foundation Size upto required depth from Ground levelB) Dressing of Pit and Dry stone pitching 200 mm thick including supply of stones and preparing surfacecomplete.C) Providing and laying in position cement concrete of M-10 grade of 75 mm thicknessD) Reinforcement for R.C.C. work with TMT bars including straightening, cutting, bending, placing inposition and binding all complete.E) Centring and shuttering including strutting , propping etc. and removal of form work for Footing andPedestalF) Providing & Fixing of 2 no. Required Size PLB HDPE Pipe & Foundation Bolt with template as per OEM Recommendations.G) Providing and Laying Reinforce cement Concrete of M-25 grade in Footing and Pedestal includingCuring the foundation for 7 days.H) Providing and Fixing Nosing Angle 40 mm x 40 mm x 6mm with 2 no. 100 mm long, 10 mm dia. Lugs oneach face. Pole Foundation for Octagonal pole from 7 Mtr. To 9

Add Extra for Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade direct in ground in the same trench in one rhorizontal formation including excavation of trench of size additional 20 cm inwidth, with procedure as per following points :- (a) Make a river sand bed ofheight 125 mm along the trench, (b) Lay another cable in middle of trench insuch manner that spacing between another cable is 20 cm., (c) Provide river sandbed of height 125 mm on top of the cable. (d) Lay the protective Common burntclay F.P.S. Bricks of Class designation 75/Sand stone slabs of 50 mm thicknessand 225 mm wide just above the sand bed vertically across the cable (Approx. 9no. Bricks per Mtr.), (e) Backfill the excavated soil leaving 300 mm from theGround level, (f)Lay the Cable warning tape and again back-fill the remainingportion of the trench upto the ground level and compacting the earth