Rural Development Department Tender

Item No. 4: Providing and laying in situ /Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC WITHOUT SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed / Crushed Sand ) DIfference in Cost of Crush Sand : Natural Sand at 1575 - Crushed Sand at 700, i.e. 1575 - 700 = 875 + Royalty inclusice of Surcharge 144.15 = Rs 1019.15 per CuMt.etc)

Item No. 5: Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC WITHOUT SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed / Crushed Sand ) DIfference in Cost of Crush Sand : Natural Sand at 1575 - Crushed Sand at 700, i.e. 1575 - 700 = 875 + Royalty inclusice of Surcharge 144.15 = Rs 1019.15 per CuMt. etc)

Item No. 6: Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC WITHOUT SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed / Crushed Sand ) DIfference in Cost of Crush Sand : Natural Sand at 1575 - Crushed Sand at 700, i.e. 1575 - 700 = 875 + Royalty inclusice of Surcharge 144.15 = Rs 1019.15 per CuMt. etc)

Item No. 7: Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC WITHOUT SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed / Crushed Sand ) DIfference in Cost of Crush Sand : Natural Sand at 1575 - Crushed Sand at 700, i.e. 1575 - 700 = 875 + Royalty inclusice of Surcharge 144.15 = Rs 1019.15 per CuMt.etc)

Item No. 8: Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks compacting , curing , finishing and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC WITHOUT SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed / Crushed Sand ) DIfference in Cost of Crush Sand : Natural Sand at 1575 - Crushed Sand at 700, i.e. 1575 - 700 = 875 + Royalty inclusice of Surcharge 144.15 = Rs 1019.15 per CuMt.etc)

Item No. 9: Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Item No. 10: Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete.

Item No. 11: Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete

Item No. 12: Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layers including watering and compacting etc. complete.

Item No. 13: Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15cm. to 20cm. including watering and compaction etc. complete.

Item No. 14: Providing internal cement plaster 12mm thick in single coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc.complete.

Item No. 15: Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Item No. 16: Providing neeru finish to plastered surfaces in all positions including scaffolding and curing etc. complete.

Item No. 17: Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. Complete. A) Flooring

Item No. 18: Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. Complete.b) Skirting

Item No. 19: Providing & applying washable oil-bound distemper of approved colour and shade to old & new surfaces in two coats including scaffolding, preparing the surfaces. (excluding the primer coat.) etc. complete.

Item No. 20: Providing and applying two coats of water proof cement paint of approved manufacture and of approved colour to the plastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc. complete.

Item No. 21: Providing and fixing collapsible steel gate in one /two leaveswithhotrolledverticalchannelsof18x9x3mmminimumsize,crossingsofM.S.flatsofsize18x5mmTorEsectionforrunnerofminimum40x6mmsizeforflange,M.S.flatfortoprunnerofminimumsize40x12mmwithrollerwheelsconfirmingtogradeF.G.150fittedwithsnapheadedrivetsofminimumsize6mmmax.spacingofverticalchannelsbe100mmenclosedgatepositionandclearspaceof150mmbetweentwosetsofcrossingswithholdfasts,stoppers,spaces,handles,lockingarrangementandonecoatofredleadprimerandoilpainting etc. complete.

Item No. 22: Providingandfixingsteelwindowofvarioussizesasperdetaileddrawingwithouthotdipzinccoating,withoutventilators,includingfabricating/glazingwithplain/obscuredglasspanelsofapprovedtypeandquality,ironoxidisedfixturesandfastenings,oilpaintingtwocoats complete.

Item No. 23: Providing and fixing mild steel grill work for windows, ventilators, etc. 15 kg/sqm as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete.

Item No. 24: Providing and fixing board displaying information, such as 'Name of work, Tender cost, Name of Contractor, Work completion and liability period etc', having rectangular shape of 1.20m x 0.90m size made out 18 gauge (1.25mm) thick mild steel sheet painted with one coat of Zinc chromate stoving primer and two coats of enamel paint on front side and grey stove enamel on back side and border / messages / symbols etc. with approved colour shade paint complete, on M.S.angle of size 35 x 35 x 3 mm frame with properly cross braced M.S. angles of size 35mmx35mmx3mm duly painted including Two M.S. angle iron posts of size 65 mm x 65 mm x 6 mm, 3.65 m long painted with alternate black and white bands of 25 cm width including all fixtures etc.and fixing the boards in 1:4:8 concrete block of size 60 cm x 60 cm x 75 cm including, excavation, refilling, transportation, and labour etc complete. Spec. No. As directed by Engineer in Charge

Item No. 25: Royalty Charges for HARD MURUM. Rate Inclusive of surcharge of 2% (141.34 + 2.82 = 144.16, Say 144.15)

Item No. 26: CONCRETE Compressive Strength OF C.C. Cube(Set of 3 cubes).

Item No. 27: STEEL BAR TESTING Upto 16 mm (Set of 3 Bars)

Item No. 28: BRICKS Water ABSORPTION ( Set of 5 Bricks) Compressive strength ( Set of 5 Bricks) Efflorescence ( Set of 5 Bricks)

Item No. 29: MORTOR Compressive Strength.( Set of 3 Cubes)