Military Engineer Services Tender

Suppy only liquid water proofing compound all as specified and directed.

M&L for laying water proofing treatment using 4mm thick APP modified membrane consisting fiver layers membrances with features as specified weighing not less than 3.5 kg per sqm reinforced with non woven polyester fiber @ 160gm/Sqm laid over a coat of cold applied bituminous primer @ 0.40 kg/sqm by torching the membrance and sealing the over lap by 100mm length side and 150mm width side all as per manufacturer instructions including joints and changes in direction be curved with cement mortar 1:3 mixed with SBR latex @ 200 ml/bag of cement curved well before laying membrance, all as per manufacturer instructions and to the satisfaction of Engr-in-Charge. Note: (i) Irrespective of lap the net covered area will only be measured for payment. (ii). Rate is inclusive of APP membrane, SBR Latex (iii) Applying a coat of bituminous aluminium paint @200 gm /sqm (minimum ) in two coat

Filling and reinstating of separation cracks: Opening the separation cracks at the junction of RCC and masonry where ever directed and instructed into "V" Grooves 2 to 3" from either side of the cracks by carefully marking areas to be opened up using a cutting machine and skillfully/carefully chiseling with a well sharpened chisel and hammer as directed including wire brushing and washing of concrete substrata and masonry walls with water jet to the surfaces thus prepared to the entire satisfaction of the consultant as instructed and directed. Moistening the cracks, provinding and applyin priming/bonding coat of slurry made out of "Polyalk EP" and cement (or equivalent as specified in the list of brand names) in proporiton 1:1 to surfaces prepared as instructed and directed. Filling the cracks/grooves by providing and applying "Polyalk EP" Polymer modified cement mortar (or equivalent as specified in the list of brand names) in proporiton 1:5:15 (Polyalk EP: Cement: Graded Sand/Quartz Sand) on the prepared surfaces and finishing it in the level with the existing plaster including hand packing, curing and making the surface similar to the external plastering using wooden floats/punch etc. complete all as specified and directed.

Taking down cement plastering on brick or stone walls including raking out joints hacking for key scrubbing down with water etc inside shafts all as directed by Engr-in-Charge.

Providing and applying 15mm thick ready mix external sand faced cement plaster with neat cement rendering at all locations in two coats on masonry (except stone masonry) and concrete surfaces including providing water proofing compound to the first coat of plaster as per manufacturers specification, inclunding racking out joints, hacking of concrete surface, finishing, curing, and neccesary scaffolding etc complete. Make : Asian/ JK Cement/ACC

M&L for preperation of new surface wall/ceilling by scrapping/rubbing,applying three coat of advanced anti-algal weather proof 100% acrylic smooth emulsion with silicon additives,over a coat of fibre reinforced elastomeric liquid water proofing membrane (Asian paint damp proof+ultima suprema,exterior anti fungal paint) or equivalent make, on old plastered surfaces walls/ceilling and cornires brooming down or steel wire brushing scrapping down with steel scrapper smoke soot moulds moss and efflorescent slats brading oil and greasy spots etc and making proper surface by applying ready mix preparatory wall care putty of Birla wall care or equivalent wherever required complete all as manufacturers instructions. (Manufatured by : Asian paints damp proof + Ultima suprma or Equivalents MAke). Note The Application of paint to be done by the authorised applicators of asian paint or eqlt make and contractor shall submit a written gurantee with the authorized dealer of 8 years for any type of colour fading,peeling,flaking,growth of fungus,seepage of water through the paint applied area or any other damages to the paint). Also the dealer shall appoint a person to inspect and validate the application of the system in stage wise manner.

Chipping off existing loose, damaged concrete from RCC members of all affected RCC Columns, beams, slabs and chajjas on external and internal facades etc beyond main r/f.(if required in the opinion of the consultant), carefully with chisel and hammer including relieving structural members such as column, beam and slabs of their superimposed load partially or fully by provision of adjustable steel props, frames etc. Providing and applying "Rusticide SS' Rust passivator or equivalent as specified in the Brand names to existing r/f bars including wire brushing of r/f, cleaning, washing of concrete etc complete as directed. Providing and applying two coats of rust preventor slurry made out of "Polyalk Fixoprime" or equivalent as specified in the brand names and cement in proportion 1:1.5 to exising r/f bars as directed complete. Providing and applying bonding coat of slurry made out of "Polyalk EP" or equivalent as specified in the brand names and cement in proportion 1:1 to concrete and r/f substrates complete as directed. Providing and applying 'Polyalk EP' or equivalent as specified in the brand names. Polymer modified cement mortar in required porportion (1:5:15) to RCC members including hand packing, curing and making the surface rough for plastering.

M & L fpr Apply a coat of SmartCare Primer with dilution ratio of 1:1 with water maintain a coverage of 100 sq.ft/ltr iclunding removing all dust and filling crack surface with water proofing chemical mixed with CM 1:3 on wall complete as per Manufacturere specifications

M&L for preperation of old surface wall/ceilling by scrapping/rubbing,applying,two coat of advanced anti-algal weather proof 100% acrylic smooth emulsion with silicon additives,over a coat of fibre reinforced elastomeric liquid water proofing membrane (Asian paint damp proof+ultima suprema,exterior anti fungal paint or equivalent make, on plastered surfaces walls/ceilling and cornires brooming down or steel wire brushing scrapping down with steel scrapper smoke soot moulds moss and efflorescent slats brading oil and greasy spots etc and making proper surface by applying ready mix preparatory wall care putty of Birla wall care or equivalent wherever required complete all as manufacturers instructions. (Manufatured by : Asian paints damp proof + Ultima suprma or Equivalents MAke). Note The Application of paint to be done by the authorised applicators of asian paint or eqlt make and contractor shall submit a written gurantee with the authorized dealer of 8 years for any type of colour fading,peeling,flaking,growth of fungus,seepage of water through the paint applied area or any other damages to the paint). Also the dealer shall appoint a person to inspect and validate the application of the system in stage wise manner.

M&L two coats of exterior emulsion paint ( Apex or weather coat) or water proof , white or tinted on old surfaces of walls including prepration of old surfaces and washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified .

Supplying and applying High build elastomeric waterproofing coating based on pure, hydrophobic polyurethane, cold applied of spray / brush applied, membrane with an elongation of 550% and tensile strength of 2.5 N/mm2 as per ASTM D 2370, crack bridging ability of 3mm as per ASTM C1305, no leakage upto 7 bars of water pressure as per DIN 1048, shore A Hardness of min. 45 as per ASTM D 2240. The system includes final base preparation, water based primer and applying SmartCare PU Magnum or approved equivalent in two to three coats to achieve a min. thickness of 1.2mm, etc. complete as per Manufacturere specifications

Material and labour for rendering 10 mm thick on brick or concrete surfaces in CM 1:4 finished even and fair with out using extra cement complete all as specified and directed

M & L 5 mm thick rendering in cement mortar 1:3 on brick work or concrete surface on ceiling finished even and smooth without using extra cement complete all as specified and directed

M&L for applying two coats of Anti fungal paint-APEX wting over a coat of primer to match the existing colour including preparation of newly plastered surface of wall all as per Specified and directed.

M&L for 3mm thick putty on ceilling surfaces and applying two coat of oil bond distemper and preparation the surfaces complete all as specified and directed

M/LReplacement of steel reinforcement with TMT CSR bars of appropriate size where 20% of cross section is reduced including dismantling of rusted steel including application of rust converter FEOVERT and applying protective coating IPNET-RB complete all as specified and directed.

Providing and laying Super fluid microconcrete-Roffe crete repairs (or equivalent as specified in the list of brand names) in beam bottoms, columns, slabs etc. including mixing with 5mm to 10mm size aggregates, water proof plywood/steel plate shuttering, pouring, tamping, consolidating, curing etc complete as per manufacturer's specification and consultant's instructions. The item shall be paid on actual consumption of microconcrete.

M/L Formwork to sides and soffits of floor or roof beams, beam haunch- ings, girders, bressummers, lintels, column ,cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

Material and labour for one coat of oil bound distemper on wall including preparation of old plastered surfaces complete all as specified and directed.

Complete removal of existance treatment of old wall and applying a layer of 3mm thick wall care putty in two coat on wall and applying two coat of oil bond distemper complete all as specified and directed

Material and labour preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint all as directed by Engr-in-Charge.

Material &Labour for Cutting chases, pinning in. making good to facings where equired and pointing in cement mortar 1:3 to ends or edges and cutting chases for concealed water tubing, and making good, cutting not exc 10 cm girth.

Demolition of stone slab and tiles of any description or thickness in floors, aprons etc, complete all as specified and directed

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over 15mm thick screed bedding layer in CM 1:4 for laying in floor etc complete all as specified and as directed by the Engr-in-charge

M&L Kota stone slab 12-18mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed including 10mm thick screed bed in cement mortar 1:3 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, complete all as specified and as directed. all as specified and as directed.

Demolition of PCC in ground floors & pavings n exc 15 cm thickness (below or above ground level)

M&L for 100 mm thick Cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing.

M&L for Chequered Pre- Polished PU Coated cement concrete tiles 300x300x25mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry laid over and incl 15 mm thick of screed bed or bedding layer cement mortar 1:6, for laying floor finishes.

Material and Labour for cleaning of bushes/plants/vegetations on walls/roof/chajjas/ceilings and removing/digging out the roots filling the hole and including applying antigrowth chemical and making good surfaces with cement concrete type, B1, 1:3:6, using 20 mm graded stone aggregate all as directed by Engr-in-Charge...

Disconnecting existing tanks Exc 250 & n exc 500 capacity , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position all as directed by Engr-in-Charge.

Disconnecting existing tanks Exc 500 & n exc 1000 , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in positionall as directed by Engr-in-Charge.

Dismantling of PVC existing water tank of exc 500 ltrs & n. exc 1000 ltr capacity and removing to site

Dismantling PVC water tanks Exc 250 ltrs but not 500 ltrs capacity and removing to site

S & F 1000 Ltrs capacity rotational moulded polyethylene water storage tanks, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-1991and as directed.

S & F 500 Ltrs capacity rotational moulded polyethylene water storage tanks, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-1991and as directed.

Taking up or down 20 mm dia steel tubing and connection and removal from site complete all as specified and directed

Taking up or down 25 mm dia steel tubing and connection and removal from site complete all as specified and directed

Refixing old 20mm dia steel tubing and connection in new or old positions (walls, ceilling, floors etc.)

Refixing old 25mm dia steel tubing and connection in new or old positions (walls, ceilling, floors etc.)

Supplying and laying of 20 mm dia. CPVC pipes SDR 11 & Plain CPVC SDR 11with all fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 25 mm dia. CPVC pipes SDR 11 & Plain CPVC SDR 11 with all fittings on walls/ceiling or laying in floors complete all as specified.

Supply & Fixing in repair Ball brass valves20mm dia , high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed all as directed by Engr-in-Charge.

Supply & Fixing in repair Ball brass valves 25mm dia , high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed all as directed by Engr-in-Charge.

S&F in repair PVC (SWR) 110 mm dia pipe for roof drain pipe and fixed to wall with bracket including proper packing with CM 1:3 incl removed old UNSV pipe all as directed

S & F in repair PVC (SWR) bend, 110mm dia complete all as specified and as directed by Engr-in-charge.

S & F in repair PVC sintex cover for 500 ltr / 1000 ltr PVC tank complete all as specified and as directed by Engr-in-charge.

Demolition of RCC in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended complete all as specified by Engr-in-Charge.

M&L Rolled sections Fe 410 gde E 250 as in framing, roof covering for cladding, glazing and the like fixed with angle cleats and connecting plates, etc

M&L preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamelled paint over one coat of red oxide Zinc chrome primer complete all as specified.

S&F Pre-painted galvalume( hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon, AZ 150 gm/sqm both side) , Zincalume (steel) based corrugated sheet 0.50mm thick ,of an approved colour, having tensile strength of 550 Mpa, and finished with resin coat on both surfaces as in roof covering/ cladding to wall,including flashings , ridges, valley etc fixed with self tapping screws complete all as specified.

Removing building/wall material etc.to a distance out of MoD Land beyond the lead including in the rates, including loading, unloading & stacking at the destination and Each load of material not less than 5 Cum and all as specified and directed by User or GE.