Military Engineer Services Tender
If you're typing tender ID over and again or finding it difficult to go through the cumbersome government websites for looking at Delhi tenders online. We have come up with a solution i.e. we have collated every eprocurement Delhi tender on BidAssist. Also, for any queries related to an e-tender Delhi, like the bidding process, registration process, etc., the same are explained below.
Military Engineer Services - MES Tender
Civil And Construction
Eprocure
Opening Date3 Sep 2024
Closing Soon24 Sep 2024
Tender Amount₹ 45,00,000
Costs
EMD
₹ 90,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_668028_1Tender No
GE/SW-43/2024-25Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
(iii) Sewage sump (west side) of CRF Building at cabinet sectt. sump size 3.30 mtr dia X 3.30 mtr deep).
1
-
-
(iv) Sewage sump (east side) of CRF Building at cabinet sectt. sump size 3.30 mtr dia X 3.30 mtr deep).
1
-
-
M&L for cleaning of semi underground main incoming water supply /fire fighting storage RCC sump of capacity 20000 gallons complete all internal side walls, bottom, partition walls & bottom of top slab of sump by the following stage process:- (a) Dewatering with dewatering pump with suitable piping upto nearest drain or as directed by Engr-in-Charge. (b) Desilting and removal of left over dirty water and sludge form bottom with sludge removal pump. (c) Cleaning of all internal side walls, bottom, partition walls & bottom of top slab with high pressure water jet machine with pressure of 10 to 150 bar without damaging tank surface and waterproofing. (d) All internal walls, partitions, cover slab of bottom and bottom of top slab etc. shall be cleaned with mechanical soft scrubber with cleaning detergent suitable for tank cleaning.
3
-
-
(e) Removal of remaining sludge sludge removal pump, the dirt silt and other foreign material should futher be removed by the help of industrial vacuum cleaner to make the floor, walls, partition walls, cover slab bottom etc. totally dirt free. (f) Spraying of non-toxic, bio degradable eco friendly anti-bacterial agent for disinfection/sterilization the tank from all the harmful bacteria/virus and to make the tank totally cleaned. (g)Treatment of inside the tank by exposing U.V. radiation to kill further suspended or floating bacteria if any. (h) The remaning sludge should then be removed by Removing / disposal of accumulated mud/ solid waste particles etc deposited at the bottom of the sump and walls and disposed off the same to Gazipur sanitary land MC low lying area by by means of necessary transport all up to the entire satisfaction of Engr-in-Charge and site requirement all as directed. Note:- (i) All necessary sludge removal pump, high pressure jet pump, industrial pump, ledder and other T&P required for cleaning and removing and disposal of sludge/silt/mud/grit and transportation shall be arranged by the contractor and the cost is deemed to be included in the unit rate of the items. (ii) The contractor shall be responsible for cleanliness of equipment and sewage pump house in and arround the surrounding area.
-
-
-
All as per Ser item No. 2 here-in- before but cleaning of RCC over head tank of 10000 gallons capacity at roof of 11 storied 'E' block complete all as specified and as directed.
2
-
-
All as per Ser item No. 2 here-in- before but cleaning of RCC over head tank of 5000 gallons capacity at roof of 04 storied 'F' and 'D' block complete all as specified and as directed.
3
-
-
M&L for dewatering, cleaning of service tanks with high pressure water jet to remove all masses, algae & dirt and removal of dirty water alongwith sludge using sludge machine and dispossal of the same to a safe distance and all tank internal and out side shall be cleaned with mechanical soft scrubber with cleaning detergent suitable for tank cleaning and further removing drit, slit or other foreign materials should further be removed by industrial vaccum cleaner and apply/spraying of anti bacterial sterlization spray to walls, floor complete of PVC tank of capacity upto 2000 ltrs all as specified and directed by Engr-in-Charge.
10
-
-
Supply, laying, jointing/ connecting and testing in replacement of MS Pipe/ ERW Pipe of following sizes, heavy duty, flanged ends including rubber packing nut, bolt, washer and butt welded fittings conforming to IS -3589 complete in trenches, wall, ceiling or laid in floor complete with two coats of synthetic enamel paint of superior quality after scraping, cleaning and preparation of old painted surfaces complete and making good the disturbed surface in and including disconnected /dismantaling and taking out of rusty/damaged pipe complete all as specified and directed by Engr-in-Charge.
-
-
-
(i) 300 mm bore, 6.0 mm thick ERW Pipe
6
-
-
(ii) 250 mm bore, 6.0 mm thick ERW Pipe
6
-
-
(ii) 200 mm bore, 5.6 mm thick ERW Pipe
18
-
-
(iv) 100 mm bore, 5.4 mm thick MS Pipe
18
-
-
(v) 80 mm bore, 4.85 mm thick MS Pipe
18
-
-
Supplying, laying and jointing/connecting in replacement GI water tubing, medium grade with all necessary accessories specials viz socket, bend, tee, unions, cross, elbows, nipple short piece etc. jointing materials, cutting pipes, making threads with screwed and socketed joints and fixed complete in trenches, wall ceiling or laid in floor complete and making good the disturbed surface in and including disconnected /dismantaling and taking out of rusty/damaged pipe in and including disconnected /dismantaling and taking out of rusty/damaged pipe complete all as specified and directed by Engr-in-Charge.
-
-
-
(i) 100mm bore
66
-
-
(ii) 80 mm bore
72
-
-
(iii) 50 mm bore
150
-
-
(iv) 40 mm bore
102
-
-
(v) 25 mm bore
102
-
-
(vi) 20 mm bore
112
-
-
(vii) 15 mm bore
108
-
-
M & L for making connection of G.I. distribution branch with G.I. main of following pipe sizes by providing and fixing tee/reducer tee, including cutting and threading the pipe in position without taking down complete and making good the disturbed surface all as specified and directed by Engr-in-Charge.
-
-
-
(i) 100mm bore
6
-
-
(ii) 80 mm bore
4
-
-
(iii) 50 mm bore
3
-
-
(iv) 40 mm bore
4
-
-
(v) 25 mm bore
6
-
-
Supplying, laying and jointing/connecting in replacement 3-layer PP-R pipe, SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all necessary PP-R plain & brass threaded polypropylene random fittings viz socket, bend, tee, unions, cross, elbows, nipple short piece etc. jointing materials fixed complete to wall, ceiling or laid in floor complete and making good the disturbed surface in and including disconnected /dismantaling and taking out of rusty/damaged pipe complete all as specified and directed by Engr-in-Charge.
-
-
-
(i) 40mm bore
12
-
-
(ii) 25 mm bore
12
-
-
(iii) 20 mm bore
24
-
-
M & L for making connection of PP-R distribution branch with PP-R main of 16 to 40mm Outer dia pipe sizes by providing and fixing tee including cutting and making fusion joint etc. complete and making good the disturbed surface all as specified and directed by Engr-in-Charge.
2
-
-
Supplying, laying and jointing/connecting in replacement CPVC pipes SDR 11 on walls/ceiling or laying in floors complete all as specified including all necessary Plain CPVC SDR 11 & brass threaded fittings viz s elbow, Tee, socket, bend, tee, unions, cross, elbows, nipple short piece, Male threaded brass adaptor, Female threaded brass adaptor etc. and jointing materials fixed complete to wall, ceiling or laid in floor complete and making good the disturbed surface in and including disconnected /dismantaling and taking out of rusty/damaged pipe complete all as specified and directed by Engr-in-Charge.
-
-
-
(i) 25 mm bore
150
-
-
(ii) 20 mm bore
150
-
-
Supplying, fixing and testing in replacement of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with matching flange, nuts, bolts, washers, gaskets and conforming to IS: 780 and ISI marked of following sizes including taking out old sluice valve complete all as specified and directed:-
-
-
-
(i) 200 mm
2
-
-
(ii) 150 mm
2
-
-
Supplying, fixing and testing in replacement of double flanged butterfly valve of PN 1.6 rating, CI , gear/hand lever operated, with soft seated wafer, bronze/gunmetal seat and ss 304 shaft duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 and ISI marked of following sizes including taking out old butterfly valve complete all as specified and directed:-
-
-
-
(i) 300 mm
4
-
-
(ii) 200 mm
5
-
-
(iii) 150 mm
6
-
-
(iv) 100 mm
4
-
-
(v) 80 mm
6
-
-
(vi) 50 mm
2
-
-
Supply & fixing in replacement Gun -metal, globe/ gate valves with iron wheel head, ISI marked, screwed/ flanged both ends as per site requirement of following pipe size including taking out old globe/gate valve complete all as specified and directed:-
-
-
-
(i) 80 mm
6
-
-
(ii) 50 mm
14
-
-
(iii) 40 mm
12
-
-
(iv) 25 mm
14
-
-
(v) 20 mm
18
-
-
(vi) 15 mm
10
-
-
Supplying, fixing and testing in replacement of 'Y' Strainer, flanged type, PN 1.6 rating made out of cast iion with stainless steel strainer complete with all accessories and nuts, bolts, washers, gaskets, ISI marked suitable for following pipe size including taking out old 'Y' stainer complete all as specified and directed.
-
-
-
(i) 200 mm
2
-
-
(ii) 150 mm
1
-
-
(iii) 100 mm
1
-
-
Supply & fixing in replacement Cast iron, Ball valve with PVC coated MS lever, teflon seal and stem, screwed/ flanged both ends, ISI marked as per site requirement of following pipe size including taking out old ball valve complete all as specified and directed:-
-
-
-
(i) 40 mm
8
-
-
(ii) 25mm
12
-
-
(iii) 20mm
12
-
-
Supply & fixing in replacment of Ball brass valves,high pressure,with polythene float and flynut of following sizes complete,screwed for iron pipe or brass ferrule and fixed including taking out old ball valve complete all as specified and directed.
-
-
-
(i) 80 mm
2
-
-
(ii) 50 mm
12
-
-
(iii) 40 mm
8
-
-
(iv) 25 mm
14
-
-
(v) 20 mm
15
-
-
(vi) 15 mm
15
-
-
Supply and fixing in replacement of cast iron Non return valve of following sizes, as per IS:5312 (ISI marked), swing check type with required flanges, nuts, bolts and gaskets etc.including taking out old non return valve complete all as specified and as directed.
-
-
-
(i) 100 mm
1
-
-
(ii) 80 mm
1
-
-
(iii) 50 mm
1
-
-
Supply and fixing in replacement of Brass/ GM Foot valve, screwed of following sizes, including taking out old foot valve complete all as specified and directed.
-
-
-
(i) 100mm
2
-
-
(ii) 80 mm
2
-
-
(iii) 50 mm
2
-
-
(iv) 40 mm
2
-
-
(v) 25 mm
2
-
-
S&F in replacement of rotational molded polyethylene water storage tank in multilayers of capacity 2000 ltr (Cylindrical vertical with closed top) hoisted and fixed in position on existing wall, stage, roof & RCC staging complete all as specified in SSR Part-I including complete connection of inlet and outlet pipe, tank nipple, float valve etc.
1
-
-
All as per sl item No 20 here-in-before but capacity of 1000 ltr.
1
-
-
All as per sl item No 20 here-in-before but capacity of 500 ltr.
1
-
-
Supply, fixing and testing in replacement 100mm(4") mechanical water flow meter (16 bar), flange type complete with gaskets, GI nuts, bolts and washers, meter should be leak proof and totally sealed in metallic outer body Class B CI including taking out old water flow meter complete all as specified and as directed by Engr-in-Charge.
1
-
-
Supply and fixing in replacement of unserviceable sensor suitable for water level indicator of approved make or as per existing make.
8
-
-
Supply and fixing in replacement of automatic float lever controller with float switch all as specified and directed by Engr-in-Charge.
2
-
-
Testing of water sample as per IS-10500 collected from part of MS bldg complex from M/S Shri Ram Institute for Industrial research / Bharat test house, Delhi as and when directed by Engineer-in- Charge.
14
-
-
M&L for flushing/washing, removing mud/silt in borewell casing pipe of size 200 mm bore by using heigh pressure compressor machine/DTH machinein exing borewell including removing sludge/silt diposite at the low laying area (WQMC area/Gajipur land) Complete all as directed by Engr-in-Charge.
1
-
-
M&L for lifting of MS/GI column pipes of size 50 mm bore from bore well by tripod and chain pulley. dismantling/removing unserviceable/corroded portion upto any length with the help of welding machine/cutter along with submersible pump & motor set and submersible electric cable with support wire after diconnecting all electrical connection form startor complete all as specified and as directed by Engr-in-Charge.
24
-
-
M&L for in replacement MS pipe column pipes of size 50 mm bore, heavy duty(C- class) in and including lowering to bore well with cutting, welding and jointing complete all as specified and as directed.
24
-
-
M&L for repairing, overhauling and rewinding of defective multi stage submersible pump & motor set of capacity 7.5 HP/5.0 HP including transportation from the site to work shop and back after dismentling, cleaning, repairing, overhauling, greasing and rewinding with super enamelled copper wire as per original gauge and weight. Insulating varnishing of pump & motor including replacement of faulty/defective parts such as water seals, gun metal buche set, carbon thrust bearings, pump impellers, pump motor coupling, filling/welding/maching/turning of pump motor shaft, painting and refitting after repair/replacement carefully with proper alignment/balanceing of pump & motor in and including lowering the submersible pump & motor set after coupled with pipe to bore well and testing for the proper pumping by submersible pump set complete all as specified and as directed by Engr-in-Charge.
2
-
-
Supply and lowering in replacement of flat submersible cable 3 core of size 6 sqmm, copper conductor complete all as specified and directed by Engr-in-Charge.
110
-
-
Supply and lowering in replacement of saftey steel wire for hanging submersible pump set in bore well complete all as latest rust free insulation specified and directed by Engr-in-Charge.
110
-
-
Note: Tripod, chain pulley, Spl T&P and any other items required under item srl no. 27 to 32 for lifting and lowering of column Pipe, Submersible pump & motor, Submersible cable and steel saftey wire set will deemed to be including in the quoted rates.
-
-
-
M&L for disconnecting electrically and mechanically defective induction electric motor of capacity 15 HP electrically operated three phase 415 volt,shifting to civil workshop for repair,strip opening for inspection,cutting of unserviceable burnt winding, taking out,cleaning of slots,rewinding with new super enameled, of existing size of copper conductor winding wire and replacement of unserviceable burnt insulating materials,sleeves etc,varnishing and with two coats of synthetic enamel paint of superior quality after scraping, cleaning and preparation of old painted surfaces complete repainting two cote new and other connected works,re-assembling,re-fixing at site,electrical connection fixing with pump set with nuts,bolts,washers as per original position and testing complete all as directed for satisfactory operation.
Note:- (i) T&P items and any other minor items required for installation and commissioning of electric motor will deemed to be including in the quoted rates.
(ii) Any electric connection,nut, bolts,washers,flanges including welding and cutting work will deemed to be including in quoted rates.
(iii) Any major spares/ parts required for making the motor serviceable shall be measured and paid separately under relevant items of Sch.
2
-
-
All as per srl item No 33 here-in-before but capacity of 12.5 HP
2
-
-
All as per srl item No 33 here-in-before but capacity of 10 HP
3
-
-
All as per srl item No 33 here-in-before but capacity of 7.5 HP
3
-
-
All as per srl item No 33 here-in-before but capacity of 5 HP
2
-
-
All as per srl item No 33 here-in-before but capacity of 3 HP
2
-
-
All as per srl item No 33 here-in-before but capacity of 1.5/1.0 HP
2
-
-
M&L for dismantling defective centrifugal/mono block pump of capacity 15 HP and shifting from installation to civil work shop for repairing and replacement of bearings, impeller, shaft, gun metal bush, gland packing and gland plate, nut bolt and washers,studs, gaskets etc and with two coats of synthetic enamel paint of superior quality after scraping, cleaning and preparation of old painted surfaces complete reassembling /fixing at site to it's original position incl testing on load for smooth functioning all as directed including transportation charges,testing and commissioning all as directed by the Engineer-in- Charge.
Note:- (i) T&P items and any other minor items required for installation and commissioning of pump set will deemed to be including in the quoted rates.
(ii) Any spares/ parts required for making the pump set serviceable shall be measured and paid separately under relevant items of Sch.
2
-
-
All as per srl item No 40 here-in-before but capacity of 12.5 HP
2
-
-
All as per srl item No 40 here-in-before but capacity of 10 HP
3
-
-
All as per srl item No 40 here-in-before but capacity of 7.5 HP
2
-
-
All as per srl item No 40 here-in-before but capacity of 5 HP
2
-
-
All as per srl item No 40 here-n-before but capacity of 3 HP
2
-
-
All as per srl item No 40 here-in-before but capacity of 1.5/1.0 HP
2
-
-
Supply and fixing ball bearing for electric motor of capacity 15 HP as per existing model 6307 2Z.
6
-
-
All as per Ser Item No. 47 here-in-before but of capacity 12.5/10.0 HP as per existing model 6306 2Z.
11
-
-
All as per Ser Item No. 47 here-in-before but of capacity 7.5 HP as per existing model 6205 2Z.
6
-
-
All as per Ser Item No. 47 here-in-before but of capacity 5 HP( Pump & motor) as per existing model 6204.
6
-
-
All as per Ser Item No. 47 here-in-before but of capacity 3 HP(Pump & motor) as per existing model 6203.
4
-
-
All as per Ser Item No. 47 here-in-before but of capacity 1.5/1.0 HP(Pump & Motor) as per existing model 6202.
4
-
-
Supply and fixing ball bearing of capacity for pump house 15 HP as per existing model 6207.
6
-
-
All as per Ser Item No. 53 here-in-before but of capacity 12.5 HP as per existing model 6206.
6
-
-
All as per Ser Item No. 53 here-in-before but of capacity 10/7.5 HP as per existing model 6205.
10
-
-
Supply only Gun metal impeller (as existing) suitable for centifugal pump of capacity 15 HP
2
-
-
All as per Ser Item No. 56 here-in-before but of capacity 12.5 HP
2
-
-
All as per Ser Item No. 56 here-in-before but of capacity 10 HP
3
-
-
All as per Ser Item No. 56 here-in-before but of capacity 7.5 HP
2
-
-
All as per Ser Item No. 56 here-in-before but of capacity 5 HP
2
-
-
All as per Ser Item No. 56 here-in-before but of capacity 3 HP
2
-
-
All as per Ser Item No. 56 here-in-before but of capacity 1.5/1.0 HP
3
-
-
Supply only complete gasket set suitable for centrifugal pump set of capacity 15 HP
2
-
-
All as per Ser Item No. 63 here-in-before but of capacity 12.5 HP
2
-
-
All as per Ser Item No. 63 here-in-before but of capacity 10 HP
3
-
-
All as per Ser Item No. 63 here-in-before but of capacity 7.5 HP
2
-
-
All as per Ser Item No. 63 here-in-before but of capacity 5 HP
2
-
-
All as per Ser Item No. 63 here-in-before but of capacity 3 HP
2
-
-
All as per Ser Item No. 63 here-in-before but of capacity 1.5/1.0 HP
3
-
-
Supply only gun metal shaft suitable for centrifugal pump set of capacity 15 HP as per existing model and make for Kirloskar/Crompton Greaves make pump set all as required and as direted by the Engr-in-Charge.
2
-
-
All as per Ser Item No. 70 here-in-before but of capacity 12.5 HP
1
-
-
All as per Ser Item No. 70 here-in-before but of capacity 10/ 7.5 HP
2
-
-
All as per Ser Item No. 70 here-in-before but of capacity 5/3 HP
4
-
-
M&L for re-metaling/machining/turning work for shaft of centrifugal pump set of capacity 15 /12.5 HP, welding, grinding, polishing and matching to reqiured size/shape complete all as suitable to the pump and as directed by the Engr-in-Charge.
1
-
-
All as per Ser Item No. 74 here-in-before but of capacity 10/7.5 HP
1
-
-
All as per Ser Item No. 74 here-in-before but of capacity 5/3 HP
1
-
-
Supply and fixing in replacement of Tyre coupling suitable for 15/12.5 HP centrifugal Pump set made out of FRAS neoprene rubber tyre and steel hub with nuts & bolts complete all as specified and as directed.
6
-
-
All as per item Srl No. 77 here-in-before but suitable for 10/7.5 HP centrifugal Pump set
4
-
-
All as per item Srl No. 77 here-in-before but suitable for 5/3 HP centrifugal Pump set
2
-
-
Note: Contractor should check the existing pump shaft size at site before procurement of tyre coupling.
-
-
-
M&L overhauling, serviceing, cleaning and repairing of 8000 CFM centrifugal DIDW blower after disconnecting all electrical connection and dismantling carefully blower and motor, removed all parts of blower and cleaning properly of all parts and components, and taking out unserviceable ball bearings, impller, V-belts, shaft and shaft seal and fixing of new ball bearings, V-belts, shaft with seals and impeller including alignment of blower and pulley block, welding/cutting work and replacement of unserviceable/rusted MS sheet pieces as required at site, re-assembling of the same and re-fixing at existing location by proper greasing and alignment including balancing and tightening of nuts, bolts and washers complete with two coats of synthetic enamel paint of superior quality after scraping, cleaning and preparation of old painted surfaces complete all as specified and as directed by Engr-in-Charge. Note:- (i) Cost of new nuts, bolts, washers as required at site will deemed to be included in quoted rates. (ii ) Cost of new ball bearings, V-belts, shaft with shaft seal and impeller will deemed to be included in quoted rates.
1
-
-
M&L disconnecting electrically, opening of 50/40 HP electric motor, 3 phase, 415 volts of Make-Kirloskar, cleaning of all parts, dismantling and taking out unserviceable ball bearing and fixing of new ball bearings, Varnishing of motor, alinment of pulley, re-assembling of the same and with two coats of synthetic enamel paint of superior quality after scraping, cleaning and preparation of old painted surfaces complete and re-fixing at existing location by proper tightening of nuts, bolts and washers all as specified and as directed.
Note:- (i) Cost of ball bearing, new nuts, bolts, washers as required at site will deemed to be included in quoted rates.
1
-
-
M&L for disconnecting electrically and mechanically defective induction electric motor of capacity 40 HP electrically operated three phase 415 volt, shifting to civil workshop for repair, strip opening for inspection, cutting of unserviceable burnt winding, taking out, cleaning of slots,rewinding with new super enameled, of existing size of copper conductor winding wire and replacement of unserviceable burnt insulating materials, sleeves, ball bearings and varnishing in and including two coats of synthetic enamel paint of superior quality after scraping, cleaning and preparation of old painted surfaces complete repainting two cote new and other connected works,re-assembling, re-fixing at site, electrical connection with nuts, bolts,washers as per original position and testing complete all as directed for satisfactory operation.
Note:- (i) T&P items and new nust, bolts,washers and ball bearings and other minor items required for installation and commissioning of electric motor will deemed to be including in the quoted rates.
(ii) Any electric connection, flanges including welding and cutting work will deemed to be including in quoted rates.
1
-
-
Supply and fixing in replacement of Evaporative cooling pad made out of Cellulose (pulp) sheet bonded togetther in 7mm flute size, honycomb type ,200mm thick of size (1800/1200/900/600) x 600mm as per site reuirement including taking out cooling pad complete all as specified and as directed by Engr-in-Charge.
8
-
-
Supply and fixing in replacement of 3 pole power contactor, 3 phase, 415 volts, 50 Hz type MNX-50 including front mounting add-on auxiliary contact block.
5
-
-
Supply and fixing in replacement of 3 pole power contactor, 3 phase, 415 volts, 50 Hz type MNX-45 including front mounting add-on auxiliary contact block.
4
-
-
Supply and fixing in replacement of 3 pole power contactor, 3 phase, 415 volts, 50 Hz type MNX-40 including front mounting add-on auxiliary contact block.
6
-
-
Supply and fixing in replacement of 3 pole power contactor, 3 phase, 415 volts, 50 Hz type MNX-32 including front mounting add-on auxiliary contact block.
6
-
-
Supply and fixing in replacement of 3 pole power contactor, 3 phase, 415 volts, 50 Hz type MNX-25 including front mounting add-on auxiliary contact block.
4
-
-
Supply and fixing in replacement of 3 pole power contactor, 3 phase, 415 volts, 50 Hz type MNX-18 including front mounting add-on auxiliary contact block.
2
-
-
Supply and fixing in replacement of 3 pole power contactor, 3 phase, 415 volts, 50 Hz type MNX-12 including front mounting add-on auxiliary contact block.
2
-
-
Supply and fixing in replacement of MCCB, Four pole, 250 Amps, 36KA,,415 Volts (Ics=100% of Icu) with microprocessor release suiable for existing frame size of LT panel.
3
-
-
Supply and fixing in replacement of MCCB Three pole 160 Amps, 25KA, 415 Volts (Ics=100% of Icu) with thermal magnetic release suiable for existing frame size of LT panel.
3
-
-
Supply and fixing in replacement of MCCB Three pole 100 Amps, 16KA, 415 Volts (Ics=100% of Icu) with thermal magnetic release.
3
-
-
Supply and fixing in replacement of MCB Three pole 40 Amps, 10KA, 415 Volts, 'C' curve.
4
-
-
Supply and fixing in replacement of overload relay suitable for range 14-23 A, type MN2 (As per existing sample).
4
-
-
Supply and fixing in replacement of overload relay suitable for range 30-50 A,(As per existing sample).
4
-
-
Supply and fixing in replacement of overload relay suitable for range 45-75 A, type MN5,(As per existing sample).
3
-
-
Supply and fixing in replacement of electronic timer, 3 phase, 240/415 volts, 50 Hz type ET-100, 12 to 120 second.
4
-
-
Supply and fixing in replacement of single phase preventer 415 volts, suitable for 3 phase supply.
6
-
-
Supply and fixing in replacement of 3 Phase, 415 volt, 50 Hz Semi Automatic Star- Delta starter in sheet steel enclosure suitable for 12.5/ 7.5 HP motor.
2
-
-
Supply and fixing in replacement of 3 phase,415 volt, 50 Hz, DOL starter suitable for upto 7.5/5 HP motor.
2
-
-
Supply and fixing in replacement of selector switch or start/stop switch (As per existing sample).
8
-
-
Supply and fixing in replacement of Phase indicating lamp, LED type, RED/BLUE/YELLOW/GREEN, 22.5 mm Ø, surface mounted, 240VAC suitable for panel mounting complete all as specified and directed.
22
-
-
Supply and fixing in replacement of digital type ammeter, 96x96 mm size with measuring range 0-100A , AC, three phase, class accuracy 1.5 suitable for panel mounting in and including CT, 100/5 Amp, protection class 5P10complete all as specified and directed.
6
-
-
Supply and fixing in replacement of Digital type voltmeter, 96x96 mm size with measuring range 0-500VAC, three phase, class accuracy 1.5 suitable for panel mounting complete all as specified and directed.
6
-
-
Supply and fixing in replacement of PVC insulated single core unsheathed, multistrand copper conductor cable 1.5 Sqmm, FRLS conforming to IS-694:1990 in and including copper thimbles as per site requirement suitable for panel wiring complete all as specified and directed.
120
-
-
Supply and fixing in replacement of Earth continuity conductor fixed to wall/ceiling on batten or recess or chases or buried in ground/floor or drawn in conduit/pipe or any other indicated situation as directed for loop earthing as required at site,of 20x3 mm Copper strip in and including fixing materials i.e. GI clamps,screw and copper nuts, bolts and wasers for loop joint etc. complete all as specified and as directed.
60
-
-
Excavation in trenches not exc. 1.5 m wide and not exc 1.5 mtr in deep for foundation etc. or for shafts, wells, cesspits, mainholes, pierholes etc. in any type of soil for foundation and getting out and leveling of bottom surface to required level complete all as specified and directed.
60
-
-
Returning filling including leveling,watering and well ramming soil in layers not exceeding 25 Cm complete all as specified and directed.
54
-
-
Removing the excavated materials not exceeding 50 m and depositing where directed at level not exceeding 1.5 m above the starting level complete all as specified and directed.
6
-
-
Cutting of existing road/PCC/RCC/Hard standing for laying of pipe including making good the distrubed surface to match with the adjoining surfaces with PCC 1:3:6 type C2 using 20 mm graded stone aggregate complete all as specified and directed.
2
-
-
Supply and fixing in replacement of heavy duty, lined flexible pipe of size 100 mm dia including re-connecting of existing foot valve after cleaning in sewage installations under ground all as per site requirement and all as diected.
50
-
-
M&L for Overhauling and servicing of 3Ph,50Hz, 415V vertical centrifugal multistage Pump and motor of capacity 15HP after open the suction and discharge connection and cleaning properly pump and motor, grease it adequately with check and replacing of bushes/bearings, gland packing, seals, oil rings, rubber gasket, nut, bolt & washers if required, tighten the motor earthing & motor terminals connection and replacing damage cable thembles(if required) check the alignment of pump and motor including testing complete all as directed for satisfactory operation.
Note:- T&P and minor items such as cable themble, nut, bolts, washers, gland packing bushes/ bearing, seals, oil ring, carbon buch etc.or any minor items not mentioned above will deemed to be including in quoted rates.
2
-
-
Attending of complaints of external water supply installation as and when required/ called up by this office for non functional of borewell submersible pumps or any water supply mains / distribution lines / control valves to make the water supply installation functional round the clock. minor repair will be carriedout on spot and other major item will be measured & paid seperately complete all as specified and directed. Note:- (i) T&P items, complaint register, comlaint slip book and any other minor items required for making water supply installation functional will deemed to be including in the quoted rates.
320
-
-
Supply only in replacement of GI socket 100mm / 80mm size ISI marked complete all as specified and directed.
10
-
-
Supply only in replacement of GI socket 50mm / 40mm size ISI marked complete all as specified and directed.
24
-
-
Supply only in replacement of GI socket 25mm / 20mm / 15mm size ISI marked complete all as specified and directed.
50
-
-
Supply only in replacement of GI elobow 100mm / 80mm size ISI marked complete all as specified and directed.
12
-
-
Supply only in replacement of GI elobow 50mm / 40mm size ISI marked complete all as specified and directed.
26
-
-
Supply only in replacement of GI elobow 25mm / 20mm /15mm size ISI marked complete all as specified and directed.
36
-
-
Supply only in replacement of GI union 100mm / 80mm size ISI marked complete all as specified and directed.
12
-
-
Supply only in replacement of GI union 50mm / 40mm size ISI marked complete all as specified and directed.
22
-
-
Supply only in replacement of GI union 25mm / 20mm / 15mm size ISI marked complete all as specified and directed.
36
-
-
Supply only in replacement of GI equal tee 100mm / 80mm size ISI marked complete all as specified and directed.
12
-
-
Supply only in replacement of GI equal tee 50mm / 40mm size ISI marked complete all as specified and directed.
16
-
-
Supply only in replacement of GI equal tee 25mm / 20mm /15mmsize ISI marked complete all as specified and directed.
24
-
-
Supply only in replacement of GI reducer tee 50x20mm / 40x20mm size ISI marked complete all as specified and directed.
12
-
-
Supply only in replacement of GI reducer tee 25x20mm / 20x15mm size ISI marked complete all as specified and directed.
10
-
-
Supply only in replacement of GI nipple of size 50mm / 40mm into 4 inch / 6 inch long ISI marked complete all as specified and directed.
26
-
-
Supply only in replacement of GI nipple of size 25mm / 20mm /15mm into 4 inch or 6 inch long ISI marked complete all as specified and directed.
30
-
-
Supply only in replacement of GI reducer of size 50/40mm or 50/25mm ISI marked complete all as specified and directed.
12
-
-
Supply only in replacement of GI reducer of size 40/25mm or 40/20mm ISI marked complete all as specified and directed.
10
-
-
Supply only in replacement of GI reducer of size 25/20mm or 25/15mm or 20/15mm ISI marked complete all as specified and directed.
16
-
-
Note: Labour Charges for fixing of item no. 115 to 133 are included in the quoted rate of item no. 114.
-
-
-
M&L opening of 20000 CFM centrifugal DIDW blower, servicing & cleaning of all parts, dismantling and taking out unserviceable ball bearing and fixing of new ball bearings, alignment of blower and pulley block, welding/cutting work and replacement of unserviceable/rusted MS sheet 5mm thick pieces as required at site, re-assembling of the same and with two coats of synthetic enamel paint of superior quality and anti corrosion bituminous black paint on entire blower unit & base platform after scraping, cleaning and preparation of old painted surfaces complete and re-fixing at existing location by proper tightening of nuts, bolts and washers complete all as specified and as directed. Note:- (i) Cost of T&P and new nuts, bolts, washers as required at site will deemed to be included in quoted rates. (ii ) Cost of ball bearings V-belts and shaft will be paid separately under relavent item of sch.
2
-
-
Supply only ball bearing for 20000 CFM airwasher unit's blower as per existing size and model complete all as directed by Engr-in-Charge.
8
-
-
Supply only in replacement of 'V' belt of size B-84 Make-Fenner/Dunlup
10
-
-
Supply only in replacement of 'V' belt of size B-195 Make-Fenner/Dunlup
10
-
-
Supply only in replacement of 'V' belt of size B-230 Make-Fenner/Dunlup
10
-
-
Supply only shaft suitable for 20000 CFM centrifugal DIDW blower as per existing model and make all as required and as direted by the Engr-in-Charge.
1
-
-
M&L opening of 10000 CFM exhaust air blower unit, cleaning of all panel/blower/motor/other parts, dismantling and taking out blower and motor unit completly from rusted/ damage platform base, repair of rusted /damage base platform and replacement of MS sheet 5mm thick, angle iron/C chanel of any size as per site reuirement by means of cutting, welding and painting with two coat of anti corrosion bituminous black paint on base platform after scraping, cleaning of base platform in and including repaing of RCC base with RCC 1:2:4,B0(12.5mm graded aggregate) for proper fixing of base platform on anti vibration pad, cleaning,sevicing and greasing of DIDW blower and motor and replacement of unserviceable ball bearing and fixing of new ball bearings, belts, filters, alignment of blower, re-assembling/fixing the blower and motor assembly with Vibration isolations pads for the blowers and pumps, all side and roof top panels by new GI nuts, bolts and washers and connecting all electrical connection including Canvass connections at the outlet, testing complete all as specified and as directed. Note:- (i) Cost of ball bearings, belts, filters, new nuts, bolts, washers as required at site will deemed to be included in quoted rates.
1
-
-
Supply, fixing and balancing in repir/replacement of site fabricated GI sheet metal rectangular/ round ducting complete with neuperene rubber gaskets, elbows, bends, slip on flanges, GI thread rod, vanes, in and including fixing and supports meterials as per site requirement etc. complete all as specified and directed by Engr-in-Charge of following size GI Sheet:-
-
-
-
(i) 22 Gauge (0.711mm)
24
-
-
(ii) 24 Gauge (0.559mm)
24
-
-
M&L for fabrication air grill with fins made out of 18 SWG GI sheet as per existing size and shape and fixing on existing exhaust air duct with fixing arrangements as per site requirement including two coats of synthetic enemal white paint over one coat of metal primer complete all as spicified and as directed by the Engr-in-Charge.
12
-
-
Supply & fix in replacement of SS padlock, 7 leaver, 65mm with 3 keys suitable for indoor and outer uses in and including two common master keys of all locks complete all as specified and as directed.
16
-
-
M&L for preventive maintenance, serviceing, cleaning, painting and repair/replacement of rusty / faulty / damage parts/compentents of PNG/LPG fired incinerator by well experance and experts manpower of this field, throughly cleaning of incinerator from outside and insidecomplete and check proper working of all PNG/LPG piping, control valve, control regulator, gas burner, temperature controller, primary and secondary chambers, scrubber, chimney and blower fan with motor and found/shown any abnormal condition in incinerator, repair/replace, defective/damage parts by fixing/welding/cutting/fabrication work in and including and repair of doors, fixing of insulation brick lining and replacement of unserviceable/rusted Tees, Angles, Channels and MS sheet 5mm thick for chambers and 2mm thick chimney as required at site, and painting of complete incinerator with two coats of heat resistant aluiminium paint of superior quality after scraping, cleaning and preparation of old painted surfaces complete all as specified and as directed by Engr-in-Charge. Note:- (i) T&P items, structural steel such Tees, Angles, Channels and MS sheet as and any other minor items , nuts, bolts, washers and cleanig matreials quired for installation will deemed to be including in the quoted rates.
(ii) Any spares/ parts required for making the incinerator serviceable shall be measured and paid separately under relevant items of Sch.
1
-
-
Supply only high temperature door gasket made out of asbestos as per existing size and shape.
2
-
-
Supply only thermocouple rod made out of stainless steel of 12 mm dia, 450 mm long, 'K' type as per existing size and shape.
1
-
-
Supply only high alaumna retractory fire bricks for primary and secondary chamber of gas fired incinerator all as directed by the Engr-in-Charge.
180
-
-
Supply only cast able compound suitable for laying of fire bricks in primary and secondary chamber of Gas fired incinerator all as directed.
4
-
-
Note: Labour Charges for fixing of item no. 145 to 148 are included in the quoted rate of item no. 144.
-
-
-
M & L for dismantling and taking down corroded/worn out base frames/pit covers, any type of water supply/ sewage/ fire incinator installations and supply and fix new base frames/pit covers,made out of MS angle iron frame/MS chanel/ MS plates/ MS flat or round bars including welding work,duly painted with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.
180
-
-
M&L for painting up to 300 mm bore New/ Existing old MS pipe with one coat of red oxide and two coats of synthetic enamel paints with bursh/spray gun after scraping of old paints, preparation of surfaces to be painted shall be made free from any loose paint, dust, grease and any fungus, algae or moss, on it shall got be removed thoroughly by vigorous wire brushing and cleaning with wateras per existing colour code complete all as specified and directed.
60
-
-
M&L for painting of existing old exhaust air duct or any euipments of installations with one coat of of synthetic enamel paints with spray gun after scraping of old paints , preparation of surfaces to be painted shall be made free from any loose paint, dust, grease and any fungus, algae or moss, on it shall got be removed thoroughly by vigorous wire brushing and cleaning with water as per existing colour code complete all as specified and as directed by Engr-in-Charge.
250
-
-
Attending breakdown/ inspection of 3000 LPH Capacity RO Plant by Sevice Engineer of OEM to check the serviceability and repalcement of any parts related to breakdown complete all as specified and directed.
Note: (a) Spares for replacement shall be measured and paid separately.
(b) A sum of Rs. 1000/- will be recovered in case of not attending breakdown by service engineer within 24 hrs.
35
-
-
Supply only in replacement of membrane housing as per existing make and model complete all as specified and directed.
2
-
-
Supply only in replacement of industrial membrane of any size suitable for 3000 LPH RO Plant.
2
-
-
Supply only in replacement of Big blue spun candle of any size as per existing make & model complete all as specified and direced.
20
-
-
Supply only antiscalent chemical as per existing make complete all as specified and directed.
60
-
-
Supply only in replacement of multimedia sand filter as per existing make complete all as specified and directed.
2
-
-
Supply only in replacement of activated carbon as per existing make complete all as specifed and directed.
60
-
-
Supply only in replacement of dosing pump of any capacity as per existing make and model complete all as specified and directed.
2
-
-
Supply only in replacement of LPS (Low Pressure Safety) Cutoff Valve as per existing make and model complete all as specified and directed.
6
-
-
Supply only in replacement of HPS (High Pressure Safety) Cutoff Valve as per existing make and model complete all as specified and directed.
6
-
-
Supply only in replacement of Float Switch (Big) as per existing make and model complete all as specified and directed.
3
-
-
Supply only in replacement of Flow meter scale of Range 1200-7800 LPH as per existing make and model complete all as specified and directed.
3
-
-
Supply only in replacement of Multi Port Valve as per existing make and model complete all as specified and directed.
3
-
-
Supply only in replacement of Flow Restrictor Valve as per existing make and model complete all as specified and directed.
2
-
-
Supply only in replacement of FRP Vessel suitable for 3000 LPH RO Plant as per existing make and model complete all as specified and directed.
2
-
-
Supply only in replacement of 3-Pole power contactor 415 Volt 15 Hz as per MNX 12 of L&T or equivalent as approved by GE.
4
-
-
Supply only in replacement of Relay suitable for MNX 12 contactor as per existing make and model complete all as specified and directed.
4
-
-
Supply only in replacement of Timer suitable for MNX 12 contactor as per existing make and model complete all as specified and directed.
2
-
-
Supply only in replacement of water pressure gauge of capacity 0 to 7 psi and 0 to 100 Kg/sq cm rating as per existing make and model complete all as specified and directed. Note for Item Ser No 153 to 169:-
Fixing of these items shall be covered and deemed to included in quoted rate of Item Ser No.152.00
2
-
-
S&F in replacement Chlorine dosing system, consisting of one FRP/ HDPE tank of 100 litres capacity with a positive displacement diaphragm Dosing pump with a variable flow rate of 0-12 LPH, motor suitable for operation at 240 V, one Phase, 50 Hertz, with necessary poly propylene piping, valves, strainers & injection fittings for system to dose solution to the feed line, as per specification suitable for RO plant 1500LPH, complete all as specified and as directed.
2
-
-
M&L for opening & removing membrane from the housing of 3000 LPH RO Plant and carried out Chemical Washing by using high power antiscalent powder & liquid. Removing sand & carbon media from the vessels and cleaning the same for dirt and silt, refilling carbon and sand media into the vessels, refixing membranes after chemical washing and drying back to its housing complete all as specified and as directed.
Note:- Chemical Washing to be carried out once in every 6 Months as per normal conditions recommended by OEM.
9
-
-
M&L Dismantling PVC water storage tank 2000/ 1000/ 500 Ltrs.
3
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%