Military Engineer Services Tender

Supplying , installation, testing and commissioning LT panel board , suitable for working on 3 phase, 4 wire, 415 volts, AC, 50Hz Outdoor type, cubicle, floor mounted, free standing, dust and vermin proof, air ventilation, factory fabricated made out of 3.2 mm thick CRCA sheet duly powder coated and shall be CPRI approved and as approved by GE. The Panel shall have front and rear opening, locking arrangement, bus bar chamber and switch gear compartment, hinged door with rubber gasket, bottom cable entry holes for incoming and out going cables, earthing terminals, affix danger notice plate, aluminium bus bar duly covered with heat shrink sleeves colour coded duly fixed on DMC/SMC insulators, aluminium strip connection from bus bar to outgoing MCCBs and copper conductor cable of adequate size for MCBs, housed in a separate bus bar chamber and control wiring adequate size and length, outgoing MCCBs shall have extended bus bar links and Panel mounted on 50x50x5mm size MS angle iron frame duly painted including PCC 1:2:4 Type B1 (using 20 mm graded stone aggregate) in foundation design subject to approval of GE as per site requirement. The minimum depth, height, width of panel is 450x1800x1500 mm respectively, minimum clearance from ground level is 450mm including removing old unserviceable item complete all as specified and directed and comprising of following (Jr Sailor Panel-1) :- (a) MCCB 250 Amps, FP, 35 KA, 415 volts, 50Hz-01 No (b) MCCB 100 Amps, FP, 25 KA, 415 volts, 50 Hz-03 No (b) MCCB 63 Amps, FP, 16 KA, 415 volts, 50 Hz-06 Nos (C) Digital voltmeter, with VSS-01 set, Digital, Ammeter, with CTs & ASS-01 set (d) LED phase indication lamps RYB-01 set (e) Aluminium bus bar TPN 400 Amps rating-01 set Make for MCCB,MCB :-Schneider/L&T/Legrand/Standard. Make for amp meter and volt meter :- AE/Kaycee

Supply, installation, testing and commissioning LT panel board suitable for working on 3 phase, 4 wire, 415 volts, AC, 50Hz Indoor type, cubicle, floor mounted, free standing, dust and vermin proof, air ventilation, factory fabricated made out of 2 mm thick CRCA sheet duly powder coated and shall be CPRI approved and as approved by GE. The Panel shall have front and rear opening, locking arrangement, bus bar chamber and switch gear compartment, hinged door with rubber gasket, bottom cable entry holes for incoming and out going cables, earthing terminals, affix danger notice plate, aluminium bus bar duly covered with heat shrink sleeves colour coded, duly fixed on DMC/SMC insulators, aluminium strip connection from bus bar to outgoing MCCBs and copper conductor cable of adequate size for MCBs, housed in a separate bus bar chamber and control wiring adequate size and length,outgoing MCCBs shall have extended bus bar links and panel mounted on 50x50x5mm size MS angle iron frame duly painted including PCC 1:2:4 Type B1 (using 20 mm graded stone aggregate) in foundation design subject to approval of GE as per site requirement. The minimum depth, height, width of panel is 450x1800x1500 mm respectively, minimum clearance from ground level is 450mm including removing of old unserviceable item complete all as specified and directed and comprising of following (MES S/S No-02) :- (a) MCCB 200 Amps,FP, 35 KA,415 volts,50Hz-01 No (b) MCB 40Amps,DP,10 KA, C series,230 volts,50Hz - 14 No (c) MCCB 63 Amps,FP,16 KA,415 volts,50Hz-03 Nos (e) Digital voltmeter,with VSS -01 set,Digital, Ammeter with CTs & ASS-01 set (d) LED phase indication lamps RYB-01 set (e) Aluminium bus bar TPN 300 Amps rating -01 set Make for MCCB,MCB :-Schneider/L&T/Legrand/Standard. Make for CT :- Nippen/AE , Make for amp meter and volt meter :- AE/Kaycee

Supply, installation, testing and commissioning LT panel board suitable for working on 3 phase, 4 wire, 415 volts, AC, 50Hz Outdoor type, cubicle, floor mounted, free standing, dust and vermin proof, air ventilation factory fabricated made out of 3.2 mm thick CRCA sheet duly powder coated and shll be CPRI approved and as approved by GE. The Panel shall have front and rear opening, locking arrangment, bus bar chamber and switch gear compartment, hinged door with rubber gasket, bottom cable entry holes for incoming and out going cables, earthing terminals, affix danger notice plate, aluminium bus bar duly covered with heat shrink sleeves colour coded duly fixed on DMC/SMC insulators, aluminium strip connection from bus bar to outgoing MCCBs and copper conductor cable of adequate size for MCBs, housed in a separate bus bar chamber and control wiring adequate size and length, outgoing MCCBs shall have extended bus bar links and panel mounted on 50x50x5mm size MS angle iron frame duly painted including PCC 1:2:4 Type B1 (using 20 mm graded stone aggregate) in foundation design subject to approved of GE to sent the site requirement. The minimum depth, height, width of panel is 450x1500x1200 mm respectively, minimum clearance from ground level is 450mm including removing old unserviceable item complete all as specified and directed and comprising of following (Jr Sailor Panel-2) :- (a) MCCB 100 Amps, FP, 16 KA, 415 volts, 50Hz-1 No (b) MCCB 63 Amps, FP, 10 KA, 415 volts, 50Hz-2 Nos (c) MCB 63 Amps, FP, 10 KA, 415 volts, 50Hz-4 Nos (d) MCB 40 Amps, FP, 10 KA, 415 volts, 50Hz-3 Nos (e) Digital voltmeter, with VSS, Digital, Ammeter, with CTs & ASS-01 set (f) LED phase indication lamps RYB-01 set (g) Aluminium bus bar TPN 200 Amps rating - 01 set (h) Analogue time switch (Daily time switch) suitable including fixing arrangement with and including power contractor 63 Amps ML-2 type, 3 Phase, 415 volts and MCB TPN 63 Amps, 10 KA 'C' series. Make of Contactor:- Siemens/L&T/ABB/Schneider/GE. Make of Timer:-Legrand/L&T/GE Make for MCCB,MCB :-Schneider/L&T/Legrand/Standard. Make for CT :- Nippen/AE , Make for amp meter and volt meter :- AE/Kaycee