South Central Railway Tender
To know what Andhra Pradesh government has posted about any AP etender, Bidassist helps us to get a one-stop platform where a registered bidder can have access to the details on each and every eprocurement tender. There is no need to provide the details on the AP E-procurement website i.e. https://www.apeprocurement.gov.in as BidAssist helps us find the specific etender we're looking for. BidAassist has collated each and every Eproc Andhra Pradesh Tender on its website.
South Central Railway - SCR Tender
Railway
Telecommunication Services
Ireps
Opening Date
10 Jul 2020Closing Date
4 Aug 2020Tender Amount
₹ 6,06,82,396Costs
EMD
₹ 4,53,400Document Cost
₹ 11,200Tender Fee
Refer Documents
Summary
Provision Of Macls Outdoor Signalling Arrangements At Potlapadu And kurichedu(ph-i) Stations And Phase-ii Miscellaneous Signalling Works At Donakonda station In Connection With Doubling Of Track Between Gnt-gtl Sections Of Guntur Division of S.c. Railway.
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
3218191Tender No
B-SG-CN-SnT-1-2020-21Tender Authority
South Central Railway ViewPurchaser Address
-Website
http://www.scr.indianrailways.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
ACS 54
Technical Guidelines for SnT works
detailed tender document kcd poo
General Condition for SnT Works
BOQ Items
Supply of CLS ladder set complete with staging, supports, signal number plate, cast iron ladder base to suit 3.5 Metre post as per drg.no.SA.23153.S.2033. Inspection: RITES.
12
3574
42888
Supply of Surface base 140mm dia. post to suit item no. 1 & 2 as per Drg.S.2011/M. Inspection : RITES.
36
2370
85320
Supply of Offset bracket to suit 140mm dia. CLS post with two numbers of 'U' bolts and nuts complete as per SA-23080. Inspection: RITES.
5
3377
16885
Supply of Calling On signal unit complete and 'U' bolts to drawing no.SA.24351 /Adv. Inspection: RITES.
5
3242
16210
Supply of position light shunt signal ground type complete with base , Pipe, hoods to Drg.No.SA.23840/Adv./Alt.1 - S.23202 (Adv.) Spec. IRS: S.6/81. Inspection: RITES.
10
4160
41600
SOR:115. Supply of Colour light signal unit:
-
-
394967
Supply of GKP type Location Boxes Full size as per drg. No. S&T/MFT/2378 (Single). Inspection: RITES.
101
8960
904960
Supply of GKP type Location Boxes Half size drg. No. S&T/MFT/2378 (Half). Inspection: RITES.
54
5529
298566
Supply of 'E' type locks of different wards as per requirement with key per E- type lock to Drg. No. SA.3376/M/Latest and RDSO Spec. No. IRS. S.30/64. Inspection: Consignee.
153
560
85680
Supply of relay fixing frame for Full location box, the frame should be made out MS angle of 25mm X 25mm X 3mm and approximate size of 940mm X 150mm with suitable holes to fix the same in the box. Inspection: Consignee.
64
591
37824
Supply of hylam sheet, resin bonded, 6mm thick, grade P3, to IS specification IS: 2036 of 1974 or latest and size 2400mm X 1200mm of colour approved by the site in-charge. Inspection: Consignee.
26
4821
125346
Supply of hylam sheet, resin bonded, 6mm thick ,grade P3, to IS specification IS: 2036 of 1974 or latest and size 2400mm X 600mm of colour approved by the site in-charge. Inspection: Consignee.
6
2356
14136
Supply of Ground Connections for the universal type point machines as per drg.no. RDSO.S.3362. Inspection: RITES.
34
5767
196078
Supply of insulations for 'D' clamp switch extension bracket to suit to universal point machine as per drawing supplied by the Railways. (One set consists of 'D' clamp insulation - 2 No. Nylon insulation bushes 4 No., Nylon insulation washers - 8 No.). (To be procured from RDSO approved firm). Inspection: Consignee.
34
496
16864
Supply of drive lug insulation for universal point machine to be procured from RDSO approved firms. (One set consists of one number central insulation plate, bushes - 2 No. and washers - 4 No.). Inspection: Consignee.
34
109
3706
Supply of Track lead junction boxes fiber glass as per Drg.No.CWM-00597of F.R.P material to 19 IRS.S.23 specification along with fixtures i.e., on MS angle 50x50x5mm, 0.9 Meters long two numbers of G.I. pipes of 25mm dia. along with nuts and bolts and 500mm long (this includes gromite bushes, 60mm PBT terminal). Inspection: RITES.
440
1057
465080
Supply of track feed regulating resistance disk type 0 to 30 ohms as per Drg.No.SA.20161/06/M or latest. To be procured from RDSO approved firms. Inspection: RDSO.
77
243
18711
Supply of B type chokes to specification no.IRS-S.65/83 to amendment no.1 or latest. Inspection: RDSO.
154
1604
247016
SOR-407: Stationary low maintenance secondary lead acid cells as per RDSO specification IRS-S- 88/2004 with topping up frequency up to 6 months. This includes supply of inter cell connectors, bolts nuts, acid level indicating floats and vent plugs.
-
-
615958
Supply of Hydro meter. Inspection: Consignee.
12
191
2292
Supply of distilled water for topping of secondary cells. (to be supplied at site.) IS 1106. Inspection: Consignee.
1200
7
8400
Supply of AC immunized plug-in-type Style 'QSPA1', DC Neutral line, slow to pickup, 24V, 8F.4B 25 contacts, front and back contacts metal to carbon, complete with plug board, retained clip & connectors conforming to BRS:933A, IRS:S 60, IRS:S 34 & IRS:S 23 (as applicable). The interlocking code for this unit shall be ABDEJ.(with ATC clips). Inspection: RDSO.
85
4367
371195
Supply of AC immune, plug-in-type, Style 'QTA2' DC Neutral track, 9 ohm, 2F/1B contacts, front 26 and back contacts metal to carbon, complete with plug-board, retaining clip and connectors conforming to BRS: 939A, BRS: 966 (Appendix F2), IRS:S 34 & IRS:S 23 (as applicable). The interlocking code for this unit shall be FGHKX.(with ATC clips). Inspection: RDSO.
85
3271
278035
Supply of Relay, plug-in type, Style 'AC-LED' All aspects, AC lamp proving relay unit with in-built 27 current transformer type, slow release neutral line relay, 4F.4B contacts, front and back contacts metal to carbon, shall be suitable for working in series with the 110V AC, LED signal lamp Rate (in Rupees)d at 15W confirming to RDSO spec. STS/E/Relays/AC lit LED signal/09-2002, BRS 941A,IRS:s34 & IRS:S23 (as applicable). The interlocking code for this unit shall be ABDHK(with ATC clips). Inspection: RDSO.
115
4831
555565
Supply of point contactor relay QBCA-1 AC immunized miniature plug in type DC biased contractor, 28 attractive armature 24Volts DC with 2HF/4B contacts, Heavy duty front contact, contacts metal to carbon complete with plug board, retaining clips and connectors to specification. BRS 943,IRS S34, IRS S23 as applicable. Inspection: RDSO.
40
6859
274360
Supply of Relay Non-AC immune, plug-in-type Style 'QN1, DC neutral line, 24V, 8F/8B contacts, 29 front and back contacts metal to carbon with plug board retaining clip and connectors confirming to BRS 930, IRS- S34, IRS-S23 (as applicable). The interlocking code for this unit shall be ABCDF.(with ATC clips). Inspection: RDSO.
120
2992
359040
Supply of Relay, Non-AC immune plug in type, style QN1, DC neutral line, 24V, 12F/4B contacts, 30 front and back contacts metal to carbon with plug board, retaining clip & connectors conforming to BRS:930, IRS: S 34 & IRS:S 23 (as applicable). The interlocking code for this unit shall be ABCDE.(with ATC clips). Inspection: RDSO.
310
2930
908300
Supply of Relay AC immune, plug-in-type Style 'QNA1, DC neutral line, 24V, 8F/8B contacts, front 31 and back contacts metal to carbon with plug board retaining clip and connectors confirming to BRS 931A, IRS- S60, IRS-S34 and IRS-S23 (as applicable). The interlocking code for this unit shall be ABDGH.(with ATC clips). Inspection: RDSO.
180
3173
571140
Supply of Relay AC immune, plug-in type Style 'QNAI, DC neutral line, 24V, 12F/4B contacts, front and back contacts metal to carbon with plug board retaining clip and connectors confirming to BRS 931A, IRS S60, IRS S34 and IRS S23 (as applicable). The interlocking code for this unit shall be ABDFH. Inspection: RDSO.
60
3143
188580
Supply of Relay AC immunized, plug in type, style QNA1K, DC neutral line, 24V 1000 ohms, 6F.6B 33 contacts, front contacts metal to carbon and back contacts metal to metal / carbon, complete with plug board, retaining clip and connectors conforming to BRS 931A, IRS S60, IRS S34,IRS S23 and RDSO specification STS/E/Relays/UEA (PI), dated 30-6-97 (Annexure - II) (as applicable). The interlocking code for this unit shall be CDEKY.(with ATC clips). Inspection: RDSO.
80
3178
254240
Supply of Cable termination racks size 880mm x 2 Meters made out of 50mmx50mmx6mm thick MS angle with stainless steel nuts and bolts for fixing of the rack with POWDER COATED and drilling suitable 34 holes to suit hylum sheet and relay frames complete as per standard practice with tripod bases and reel insulators (for K rack, P rack and power rack) and with cable ladder of width 400mm and length of 2 Mtrs. The thickness of angle to be 5mm. two angles of 40mmX40mmX5mm to be supplied at both ends and supporting flats of 25mm X5mm. Inspection: Consignee.
20
5125
102500
Supply of terminal block 1 way PBT 60mm as per RDSO Drg. No. SA.23745/Alt.5 & IRS S.75/91 & IRS.S.23 with latest amendment. Inspection: RDSO.
1900
61
115900
Supply of terminal block 6 way PBT 25mm as per RDSO Drg. No. SA.23756/Alt.3 & IRS S.75/91 & IRS.S.23 with amendment no.2 or latest. Inspection: RDSO.
5300
285
1510500
SOR-607: Supply of Non-deteriorating type of fuse holders & fuse links - electric fuse for Railway 37 signalling Rate (in Rupees)d voltage 240 AC/DC to Specn. No. IRS S.78/92 (IRS-S-78/97 Tentative) IS:13703 (part 2/sec2):1993 suitable for E1 fuse 20Amps SC-20 Holder Safe Clip / knife edge type size E1 (R-SS) amp. Inspection: RDSO.
-
-
165690
Supply of indoor cable 60 core X 0.6mm as per IRS S.76/89 amend no.2 or latest. Inspection: RDSO.
1
128938
128938
Supply o f PVC insulated wire copper conductor 16/02mm to ATC IS:694 to RDSO specification 39 no.IRS.S76/89. Each coil of 100 mtrs. length. To be procured from RDSO approved firms. Per Unit= Coil. Inspection: RDSO.
550
797
438350
Supply of PVC insulated wire multi-strand copper conductor 10 Sq.mm flexible Specn.IRS.S76/89. Amendment No.2 or latest. Each coil of 100 mts. length. To be procured from RDSO approved firms (size 140/0.3mm). Per Unit =Coil. Inspection: RDSO.
64
9390
600960
Supply of PVC wire coils of size 28/03 multi strand (flexible). Spec. IRS.S 76/89. Amendment No.2 or latest. Each coil of 100 mts length. To be procured from RDSO approved firms. Per Unit =Coil. Inspection: RDSO.
44
1635
71940
Supply of Battery charger of 230Volts AC / 110V DC 30 Amps single phase, signalling / telecom. Instrument as per RDSO Spec. IRS S.86/2000 Amd.1 or latest. Inspection: RDSO.
2
74911
149822
Supply of Battery Charger 230V AC /24-26V-28V DC 30 Amps Capacity. RDSO Specification No.IRS.S.86-2000.(or latest). Inspection: RDSO.
2
29886
59772
Supply of Transformer Rectifier 11OV AC Input /24V-30V DC Output, 5 Amp capacity, as per spec. IRS S 91-2014 with amendment 1 to be procured from RDSO approved firms. Inspection: RDSO.
7
3196
22372
Supply of Universal locks with one key for every ten locks. Inspection: Consignee.
150
60
9000
Supply of Cement Portland / Ordinary, confirming to ISS: 269/76.(To be supplied at site as per requirement and as per instruction of site engineer). Inspection: Consignee.
7
4027
28189
Supply of electric track drilling machine similar to model no WD 34 C,RALLI WOLF Make with suitable horizontal stand with attachments to drill holes of various sizes up to 7mm to 13mm . Inspection: Consignee.
2
15161
30322
Supply of steel stools 18" height neatly finished and painted. Inspection: Consignee.
12
334
4008
Supply of Jerry can 2 0 Ltrs. capacity white a s p e r the requirement of SI at site. Inspection: Consignee.
10
105
1050
Supply of Navtal Locks godrej make 25/50mm as per instructions of SE/SSE(Sig) at site. Inspection: Consignee.
20
384
7680
Supply of key chains with ring with plastic name plate of 60mmx20mmx3mm duly engraving station name on one side and key particulars on one side as specified by the site in-charge. Inspection: Consignee.
130
23
2990
Transparent plastic cover superior quality for keeping circuit diagram sheets with provision for hanging size "C". Inspection: Consignee.
950
40
38000
Supply of Rubber Mat of size 2000mm X 500 mm and 12 mm thickness. Inspection: Consignee.
12
819
9828
Printing, Binding & supply of the following registers with latest proforma given by in-charge officer each register of 100 pages.. a) Station Asset Register b) Deficiencies c) Officer Inspection book d) Work site orientation classes note book. e) Station Message book f) Infringement measure book for signal gears g) Route cancellation register. h) Relay room Key register i) Selection circuit testing j) Cable testing summary k)Siganl 54 maintenance record. l) Power Supply systems(Battery maintenance ) m) Mechanical Signalling Register. n)Axle Counter Maintenance Register o) Block instrument Maintenance Register. p) Track circuit maintenance Register. q) Lifting barriers maintenance Register. r ) Electrically operated point maintenance Register. s ) Electronic Interlocking Maintenance Register. t) Location box maintenance Register. u) Earth Testing record Register. v) Cabin/Relay room register. w) Joint Inspection of Points and Crossings register. x) Block Proving Axle Counter Register. y) Diesel generator /Solar panel Register. Per Unit -Per Register. Inspection: Consignee.
130
70
9100
Supply of DWC pipe of 180 mm outer dia./ 153 mm inner dia. in length of 6 Mtr. with coupler. to IS specification No.14930 Part-II. The IS spec shall be marked on the pipe. Inspection: RDSO.
60
2640
158400
Supply of Electric Key Transmitters single complete to drg.no.SA.22601/Alt-4& IRS S.21/2001 to ward no. specified. Inspection: RDSO.
18
4767
85806
Supply of double key lock. Inspection: Consignee.
2
303
606
Supply of wire rope steel galvanized 6/19, 26 SWG for double wire Signalling to spec. No. IRS. S3- 61 ,Amd-1. Inspection: Consignee.
600
81
48600
Supply of lightening and surge arrestors of class B&C suitable for single phase supply in TT network as per amendment 5 of RDSO spec. No. RDSO/SPN/165/2004 or Latest and as recommended by RDSO letter No. STS/E/IPS/GENL dated 27.01.06(Amendment5). Inspection: Consignee.
2
14999
29998
Supply of 35 Sq.mm Multi-strand single core PVC insulated copper cable as per IS:694 for connecting Main earth electrode to MEEB in the equipment room in duplicate. Inspection: RITES.
2200
303
666600
Supply of 16 Sq mm Multi-stand single core PVC Insulated copper cable as per IS:694 for connecting MEEB to SEEB and SPDs and SPDs to MEEB. Inspection: RITES.
500
144
72000
Supply of 10 Sq. mm Multi strand single core PVC insulated copper cable as per IS:694 for connecting various equipment's to SEEB. Inspection: RITES.
500
87
43500
Supply of titanium coated 7.2mm drill bits of Bosch/Addison make. Inspection: Consignee.
80
94
7520
Supply of channel bond pins single groove 7mm dia. (100Nos). Inspection: Consignee.
35
41
1435
Supply of various type of lugs as per instructions of site in charge. Inspection: Consignee.
1400
4
5600
Supply of PVC conduit pipe 3 Mtr. length 25mm dia. with bends. Inspection: Consignee.
40
35
1400
Vulco tape of size 45mm width x 1.5 mm thick x 10 Mtr. length. It shall be self bonding type anti corrosive, heat resistant & water proof. Inspection: Consignee. Per Unit= Roll.
45
1524
68580
Supply of copper lugs10 Sq.mm. of reputed make.
1300
8
10400
Supply of Corium Z 105 Battery cleaner and terminal conditioner of 500ml tin can. Inspection: Consignee.
3
3507
10521
Supply of Copper eyelets to suit 16/0.2 wire Dowell's make. Inspection: Consignee.
2900
2
5800
Supply of Copper eyelets to suit 10.sqmm wire Dowell's make. Inspection: Consignee.
1550
4
6200
Supply of Solid State Buzzers with different frequencies in metallic/plastic casing working on 12V- 24V-60 Volts. Inspection: Consignee.
4
204
816
Supply of 2 N/2R Micro switch, L&T or Siemens make. Inspection: Consignee.
18
378
6804
Operation of any SOR Item from Chapter-1 to 18 Except Chapter-11.
3
250000
750000
Final location survey of cable route and final preparation of cable route plan as per technical specification Sch. 'B' Sl.No.2. Per unit =RKM.
17.5
994
17395
Excavation of trench to a depth of 1200mm and width of 300m at bottom in hard morum soil as per 2 RDSO Sketch no SDO/CABLE LAYING /003 including marking of cable alignment, clearing of jungle, bushes, trial pits if required, refilling with excavated soil, ramming and consolidation after laying of cables complete to the finished item of work as directed by supervisor in-charge. Per unit =RKM.
19
67092
1274748
"Cutting of rock up to a depth of 300 mm and width of 300mm where rock is visible from surface, concreting to ground level after laying cables with 1 cement: 2 sand: 4 graded stone aggregate 20mm nominal 3 size and curing of concrete to the required number of days, except in bridges, culverts, level crossings, track crossings, cable pits, rocky soil including marking of cable alignment, clearing of debris etc., complete to the finished item of work as directed by site in-charge. Drg. No.SK/CN/NEW/1. All the material is to be arranged by contractor. Per Unit =RMT.
1400
460
644000
1905-01 Cutting of rock to a depth of 200 mm and width of 200 mm where rock is visible from surface to a depth more than 300 mm up to 550mm, excavation of trench with width 300mm above rock 4 concreting 200mmx200mm after laying of cable with 1 cement: 2 sand : 4 graded stone aggregate 20mm nominal size and curing of concrete to the required number of days, refilling with excavated soil ramming and consolidation except in bridges, culverts, level crossings, track crossings, cable pits, rocky soil including marking of cable alignment, clearing of debris etc., complete to the finished item of work as directed by site in-charge. Drg. No.SK/CN/NEW/3. All the material is to be arranged by contractor. Per unit =RMT.
2300
241
554300
Digging of cable trench to a depth of not less than 30 Cms in rocky terrain, Concreting the trench with 150mm thick concrete with 1 cement: 2 sand: 4 graded stone aggregate 20mm nominal size. All the material is to be arranged by contractor. Per Unit =RMT.
1200
128
153600
Track crossing by horizontal boring method based on the drawing no.DRM/J/6735 dated 7-8-03 6 (enclosed) and as advised by the engineer at site. This includes the supply and insertion(pushing) of GI pipe (80mm) confirming to IS.1239 heavy class in the bore drilled with the coupler between two pipes. All the joints of casing pipes should be tight and leak proof. Per Unit =RMT.
3800
1403
5331400
Trenching under Rails for crossing the track(Track crossing) and refilling of trenches as per RDSO drawing No. SDO/CABLE LAYING /009. The track crossing shall be done at right angles. The depth of cable 7 trench shall be 1.2 Mtr. below the rail flange. The depth between top cable and the level of rail flange of the rail shall never be less than 1.0 Mtr.. The ballast shall be Stored separately while making the trench and the earth soil shall be stored separately. while re-filling the trench, the earth soil has to be filled first to the ground level and the ballast has to be properly put in the track. this work has to be done under supervision of supervisor of S&T and supervisor of P.Way. Per Unit =RMT.
1800
141
253800
Breaking of metal/ tar road and refilling after laying the cables as per drawing no. SDO/CABLE LAYING/010. The surface of the road shall be concreted to match with the old surface. Per Unit =RMT.
550
142
78100
Laying different type cables in the trench. Termination covered elsewhere. Per Unit =RMT.
260000
5
1300000
Supply and placing of one layer of fully burnt country bricks ('B' Class of size approximately 220mm X 100mm X 60mm) length wise vertically in the trench for separation of power cable. Size of brick can vary subject to approval by site officer. Per Unit =RMT.
1400
21
29400
Excavation of square coil pit up to a depth of 1 Mtr. X 1.5 Mtr. For providing coil at location box, point, signals etc., This includes back filling and ramming of trench / pit after laying the cable and consolidation of soil.
450
181
81450
SOR:1916. Cable laying at culverts/bridges -High flood level: Excavation of cable trench of 300mm width and 800 mm depth in the ramp from the foot of the culvert on to the top of the culvert by storing the ballast and the excavated soil separately and laying of HDPE pipe( to be supplied by Railways) duly. The pipe is to be laid, the cables required are to be drawn using bends( to be supplied by Railways) as per the drawing No.SK.15/11. After drawing the cables the bends are to be concreted to a size of 300mmX1000mmX1000mm using required shuttering /moulds. Except the HDPE pipe and bends, all other material is to be arranged by the 12 contractor.
-
-
157440
SOR: 1917(1). Supply & laying of DWC split pipe of 120/103 mm dia., 2meter long in already dug cable trenches as per Drawing No.SK.9/11 .The unit of RMT means two split pipes of 1 Mtrs. each. Per Unit =RMT. Inspection: RDSO.
5500
232
1276000
SOR: 1917(2). Supply & laying of DWC split pipe of 250/217mm dia, 2 meters long in already dug cable trenches as per Drawing No. SK.9/11. The unit of RMT means two split pipes of 1 Mtr. each. Per Unit =RMT. Inspection: RDSO.
5500
761
4185500
Supply & Laying of RCC Pipes 150mm outer dia. 2 Meters long, thickness 25mm.
220
226
49720
Providing of channel ramps for drawing cables at bridge/culvert entries duly providing GI bend/ 16 flexible conduit 8 cm diameter and constructing channels from a depth of 0.8 meters to surface as per detailed technical spec. (Concreting to be done at the ratio of 1:4:8 - Cement, sand and fine metal for concreting will be supplied by contractor.
38
496
18848
SOR: 1923. Provision and laying in position cement concrete of 1 cement:3 sand:6 graded stone aggregate of 20mm normal size excluding cost of cement, centering and shuttering ( including transportation of all the material) .
-
-
88308.24
Jungle cutting along with the cable route. Per Unit =RMT.
9000
4
36000
Cutting of masonry walls of at stations, cabins buildings and other locations as indicated by Railway engineer at site to a depth of 0.75 meters and supplying and fixing 50mm GI pipe The leading in arrangement shall be as per drawing no. RE/S&T/ ALD/SK/ 161/ 81.
13
610
7930
Test lamp arrangement in LBs/RE cuttings.(Auto mobile handle type). Per Unit =Per Location.
110
119
13090
Supply and fixing of teak wood reapers suitable for Full location Box with 50 mm width x 20mm thick and length of 940mm after applying two coats of wood primer. Per Unit =Per Reaper.
140
130
18200
Supply and fixing of teak wood reapers suitable for Full Box 75mm width x 20mm thick and length of 940mm after applying two coats of wood primer. Per Unit =Per Reaper.
140
159
22260
Supply and fixing of teak wood reapers suitable for half Box 75mm width x 20mm thick and length of 470mm after applying two coats of wood primer. Per Unit =Per Reaper.
70
97
6790
Supply and fixing of 20mm thick teak wood planks for Keeping Equipment in the Full Box after applying two coats of wood primer. The approximate size of the flank is 940mmx20mmx300mm Per Unit =Per Plank.
130
490
63700
Supply and fixing of Teak Wood planks of of sizes as instructed by the site in-charge with smooth 25 finishing surface to be provided where ever required such as in location boxes relay room, equipment room and battery room, Fine wood polish of approved quality to be applied for two times after thorough application of emery paper. Fixing bolts and wood polish supplied by the contractor painting (Hardwood, paints, fixing bolts are to be arranged by contractor).
2.5
43600
109000
Supply and fixing of H. Wood planks of 40mm thick and not less than 200 mm width with smooth surface, painting (Hardwood, paints, fixing bolts are to be arranged by contractor). Per
3.5
18673
65355.5
Numbering location box as per standard practice and writing all termination particulars inside the location box as per details. This includes all main and tail cable particulars, writing of cable numbering of cables, polishing teak wood boards in two coats and painting hard wood shelves in two coats of black enamel.
175
280
49000
Fixing relay bases, wiring in location boxes, bunching, fixing of relays as per circuit diagram. This includes fixing of condensers, resistance, 6 way / 1 way terminals/ WAGO, ND type fuses, LED indicators for fuses as per type fuses, LED indicators for fuses.
350
156
54600
Fabricating, erection and fixing in position of Tie bars fencing using Railway's rail and tie bars including transportation of rails and Tie bars from Depot to site excavating the earth of size of 0.60 x 0.60 x 1.5 m erecting rails posts and cutting rail posts to required size erecting rails posts of correct alignment using CC 1:3:6 mix of sixe 0.60 x 0.60 x 1.30 m cutting the tie bars to required size and shape and drilling holes whenever 30 required revitting/welding connecting the tie bars to horizontal bars by using 16mm dia contractor's revite and fixing the tie bar panel to rail posts using 15mm dia bolts including drilling holes in Rails including painting and one coat over the primary coat complete as per drawing No. GM/W/SC/ 3461/1 with all contractor's OP cement labour, tools bolts with all lead and lift curing complete as directed by the Engineer-in-charge. Note: Different lengths of Rails and Tie bars will be issued to Contractor at different locations in section has to be cut for the required size and to be the same has to transported to the site.
100
7176
717600
Supply of approved quality of special paint for cooling purpose and painting of Battery / BPAC boxes (Full and half GRS).
10
2938
29380
Earthing and soldering of cable armour. Per Unit =Per Cable.
3500
21
73500
Routing and connecting of all the SPDs in the equipment room to MEEB with 16 sq. mm copper cable using copper lugs with stainless steel nut and bolts (for item procured against supply). Per Unit =RMT.
160
21
3360
Routing and connecting all the equipments in the equipment/relay room to MEEB/SEEB with 10 sq mm copper cable using copper lugs with stainless steel nuts and bolts and fixtures. The work includes laying and routing the copper cable in PVC pipes/conduits and fixing them on wall. Per Unit =RMT.
300
23
6900
Fixing of Class B&C arrestors supplied along with 63 Amp HRC input fuse and fuse base in wall mountable cabinet box of size 250mm(w)x450mm(h)x150mm(d) and commissioning. The box shall be made using MS sheet of 20 gauge or better with IP31 protection and power coating. A door knob shall be provided to open the front door to access the fuse. Provision shall be made to view the working condition of class C arrestors 35 from front side of the cabinet. All the internal power wiring shall be made using 10Sq.mm PVC cable on suitable termination. The PF contacts of class C arrestor shall be wired using 2.5Sq.mm cable. The earthing point on the arrestor shall be connected to the maintenance free earth bus bar using insulated cadmium bronze cable of size 3/16'. The connecting cable used to extend main power to surge arrestors shall be PVC insulated cable of multistoried copper cable of 10Sq.mm size. All the materials required for the above work except surge arrestors and cadmium cable (Covered in supply portion) is to be arranged by contractor.
2
8767
17534
Manufacturing, Supply, painting and fixing of markers of G/P/C/A/IB Markers/Number plates with engineering grade reflective sticker on MS sheet with clamps as per drawings/as per site in-charge. including all fixing materials. Inspection: Consignee.
110
308
33880
Supply and fixing of wire mesh for the following signals, duly painted with black enamel in two coats. (4)Box type mesh for ground type shunt signal.
10
484
4840
Strengthening of foundations of signals, Full/Half location boxes, by carrying out the earth work around the foundation, ramming of the earth, caring out masonry work from bottom of earth work using country stones and cement masonry to prevent the earth from slipping down the bank.
100
2813
281300
Fixing of point machines on PSC/Wooden sleepers as per standard drawing. Wiring as per circuitry includes fixing & wiring of point contactor unit frames and controlling relays . Includes fixing of crank handle ward plate.
34
4308
146472
Wiring of Track circuits feed end, relay end complete with TLDs, batteries, chargers, track relays, 40 double lead wires, providing insulation etc,. connected with track commissioning of track circuit including provision of bracket for TLD covers and painting. Anti-tilting arrangement has to be done for track relays, chargers & batteries.
90
1004
90360
Execution (Supply , transportation, installation and commissioning) of pin brazing /exothermic out 41 weld connection for continuity bond across fish plates in DC track circuit area as per RDSO Spec. No. IRS S- 103/2004 or latest. (all equipments & material required for brazing /welding of railhead continuity will be arranged by the contractor. Per Unit =Per Bond.
240
725
174000
Execution (Supply , transportation, installation and commissioning) of pin brazing /exothermic out 42 weld connection for TLJB/boot leg as per RDSO Spec. No. IRS S-103/2004 or latest. This includes good quality insulated cable for TLJB for the above purpose. one end on rails web in track circuit area and terminating the other end of wire on the terminals in the TLJBs, (all the equipments and materials required for welding will be arranged by the contractor. Per Unit =Per Bond.
280
365
102200
Drilling of holes 7.2mm on web of the rail , providing bond wires with PVC coated wire rope. (Bond pins single grove have to be supplied by contractor - Wire rope for bonding is covered under supply portion). Per Unit =Per Rail Joint.
3500
16
56000
Fabrication, Supply and fixing of CALLING ON instruction boards, STOP boards with engineering 44 grade reflective sticker of size 600X900X1200 mm GI sheet, with MS angle of 75X75X6 mm with 6 meter length including paint, excavation of pit and concrete foundation etc..as per the instructions of sight in-charge. All necessary materials to be arranged by the contractor). Inspection: Consignee.
34
3549
120666
Providing crank handle box, wiring, testing as per technical specification including concealed wiring in the wall.
18
3848
69264
Manufacturing and fixing of glass fronted box (key box) made out of teak wood of size 10 inches x 16 inches.
4
255
1020
Fixing of PVC pipes & bends, drawing of required wires through the same up to functions like 47 control telephone, Dy. control telephone, magneto phones inside SM's office as per circuit diagram. This includes supply and fixing of required DPDT and rotary switches, PVC pipes and bends 25mm dia. with 2mm wall thickness, Lightening dischargers and painting of particulars.
3
3628
10884
Erection of Relay rack 1way/2way/4way/CT Rack with scaffolding suitably concreting tri-pod bases 48 using J-bolts, fixing rack supporting of size 50x50x6 mm on to the wall. Reel insulators are to be provided for insulating the rack from the scaffolding & tri-pod bases. ( payment based on number of equivalent 1 way relay racks). Per Unit =Per one way rack
22
341
7502
Fabrication and supply of MS frames to suit 'Q' series relays to accommodate 6 No. in each set as per Drg. No. B.SG.CN. MISC.9.98 duly drilling required holes for relay bases (All materials such as frames, bolts, nuts and washers to be supplied by the contractor) (Only Relay bases will be supplied by the Railways).
90
294
26460
Fixing relay bases on the relay frames erected in Relay Room, Wiring of all types of relays by drawing various sizes of wires/multicore cable, fixing fuses, condensers, resistances, LEDs etc and wiring duly soldering the same as per approved circuit diagram, testing point to point before soldering and after soldering, bunching and lacing as per detailed technical specification. Different colour codes and sizes of wire to be used as per standard practice. This also includes, provision of all PVC sleeves required to be provided. Copper lugs to suit 50 to 16/02 wire and neat bunching, lacing with Modi Nylon / Twine thread and using PVC dotted tape with buttons were required. This also includes soldering all the wires in the relay room with Rosine core of IS Spec. 1921 (60 Tin and 40% Led). Soldering should be done as per standard practice. This also includes inserting the clips, point to point testing as per the circuit diagram and plugging relays to Relay bases (except Inter-cables, relays other materials such as Rosine core, flux, nylon thread. PVC dotted tape should be supplied by the contractor). Point to point testing should be done in the presence of Engineer-in-charge as instructed in two stages, one before soldering and the other after soldering.
260
174
45240
SOR: 2615(01). Fixing of approx.200 Nos. 6 way/ 1 way terminal blocks horizontally on 6mm hylem 51 sheet which in turn to be fixed to rack with all supports as per instructions of site in-charge. Material such as bolts , nuts , washers, screws, supporting flats are to be arranged by the contractor.
22
479
10538
SOR: 2615(02). Cutting and fixing of hylem sheet 6mm / 3 mm thick to suit to 1-way relay rack and fixing wire wound resistances and condensers of various values. Material such as bolts, nuts, washers, screws, clips, resistances are to be arranged by the contractor.
22
103
2266
SOR: 2615(03). Fixing of ND type fuses with LED indication and resistances along with negative terminal strips on 6mm hylem sheet with contractors bolts, nuts, screws and washers.
420
5
2100
Preparation of Contact Analysis for 'Q' style relays as per detailed technical specification.
580
14
8120
Indoor Painting as per technical specification for 4/5/6 road stations.
5
3301
16505
Provision of one skilled and 2 unskilled staff round the clock to attend to teething trouble of the installation along with SI/CSI after the installation has been brought into commissioning. The work includes routine maintenance, failure restoration as per the direction of the SI/CSI. Per Unit =Per Month.
12
43437
521244
Fabrication, fixing of required configuration of key in point machine for grouping of crank handle of point machines.
34
82
2788
Non Interlocking arrangements.
3
12300
36900
SOR: 2701. Transportation of materials from any Stores to Site and vice-versa including loading and unloading.
-
-
1069650
Installation and wiring of all power supply equipments, viz DC Distribution system, chargers, 60 transformers, batteries etc, and its wiring as per the tech spec. No10.8(lacing ,bunching with copper eyelytes/lugs required for crimping 10sqmm wire are to be supplied by the contractor. for power panel, bolts, nuts and fixing screws are to be arranged by the contractor. hylam sheets and wire coils will be arranged by the railways.
2
12227
24454
SOR: 2802. Initial Charging of Secondary Cells:-
-
-
58268
SOR: 2901(1). Testing of wires drawn point to point using buzzer. (Before and after soldering.) Per Unit =Per Sheet.
110
316
34760
Fixing of LEDs along with Jewels, Resistors, Sleeves duly drilling holes and soldering including drawing of wires, bunching and lacing. (All materials to be supplied by the contractor).
280
12
3360
Supply and fixing of 'AHUJA' make horn type loud speaker 15W 8 ohms impedance. Inspection: Consignee.
4
937
3748
Supply and fixing of Electronic Hooter unit 24/110 DC of approved design/make able to drive 2 No. of Speakers of 8 ohms 15W. Inspection: Consignee.
4
1820
7280
Fixing and wiring RKT/EKT for siding or L.C. Gate interlocking as per Tech./Spec. No. 15.12. This includes installation of Magneto telephones at location, gate, SM's office etc.,
8
602
4816
Releasing of the following equipments without causing damage, stacking neatly at a centralised 67 place near the site of work as shown by the in charge, and handing over the same to the Stores depot as per the inventory made. Releasing of mechanical point equipment complete/HP layout/Point & trap indicator/Electrical point machines.
2
224
448
Releasing of location boxes Full/Half/sheet iron.
114
148
16872
Releasing of Warning Boards/stop boards.
5
252
1260
Releasing of Pully stakes single/double wire.
20
19
380
Releasing of block counter.
5
306
1530
Releasing of block instrument.
5
307
1535
Releasing of Ground lever frames.
2
203
406
Releasing of Cranks / Compensators.
4
24
96
Releasing of lifting barrier gate.
2
665
1330
Releasing of existing Axle Counter field equipment (transmitters 2 No. receiver coils 2 No.) on the 76 rails at the entry/exit track circuits without causing any damage. Excavating the under the track for removing track devices, connecting cables and duly covering the cable duct. Disconnecting and removing of Amplifier (electronic junction box and other associated equipment from the location box and transporting to a central location for accountal.
5
702
3510
Releasing of colour light signal 1/2/3/4 way complete.
31
532
16492
Releasing of shunt signals ground type complete.
5
141
705
Electrical point equipment complete.
18
213
3834
Releasing rodding. Per Unit =RMT.
80
1
80
Releasing of 2 way / 4 way trestles.
40
11
440
Design of cable route plan, cable core chart, location box particulars, panel particulars, fuse particulars, track bonding diagram, numbered wiring diagrams, relay index, contact analysis, posting of contacts in wiring diagram to be supplied by Rlys, surveillance panel particulars, data logger particulars, K rack, rack details, 82 resistor, condenser particulars, power equipment wiring, power equipment foot print diagram, etc as per requirement. Supply of 6 sets of final hard copy of the approved circuit diagrams and the documents mentioned above along with contact analysis in A2, A3, and A4 sizes as required with 1 set of prints on tracing film and a soft copy on compact disc (CD) to be supplied. (Arranging rexin cloth bound booklets and binding for large and small sizes of drawings).
3
83295
249885
SOR: 3302(6). (g) Arranging rexin cloth bound booklets and binding for large size drawings. Per Unit =Each Booklet.
18
174
3132
SOR: 3302(7). (h) Arranging rexin cloth bound booklets and binding for small size drawings. Per Unit =Each Booklet. Per
18
142
2556
Carrying out circuit alterations in the existing location boxes as per the new circuits which require excavation and releasing unwanted cables from the location box and taking new cables inside the location, clamping of new cables, filling the location box with standard up to the bottom of location and plastering.
35
612
21420
Supply and fixing of different sizes of PVC casing /Pipes as required by Railway at site by fixing 87 /clamping to the wall for indoor wiring purposes. . The material required carrying out the wiring such as soldering, lacing, casing, fixing clamps; screws etc., are to be provided by contractor on his own cost. Per Unit =RMT. Inspection: Consignee.
250
32
8000
Operation of any other SOR Items from Chapter-19 to 27
3
250000
750000
Supply of Polymeric Positive Temperature Co-efficient Device (Self-Re setting type) 1.1 Amps 1 capacity with soldered 16/0.02 copper wire leads (As per required length) and crimping of copper lugs. Necessary wire coils will be supplied by the Railways. materials such as solder lead, copper lug etc., are to be arranged by the contractor within the cost of the work. Make little Fuse/TYCO/Fuzitech only. Inspection: Consignee.
370
130
48100
Fabrication & supply of G.I. termination box for point machines of size 45 cm x 23 cm x 12 cm. The termination box to be fabricated out of G.I. sheet 10SWG and to be with 2 nos. of M.S. angle of size 50x50x6mm 2 of length 1000mm each and GI pipe of 40 mm dia and length of 450mm. The termination box is also provided with teak wood plank of size 25 mm thicknesses for fixing of terminals. Necessary bolts, nuts and screws are to be provided for fabrication of termination box. (All materials are to be procured by the contractor). Inspection: Consignee.
60
2579
154740
Earth Leakage detector 12 channels as per RDSO Specn. No. RDSO/SPN/256/2002 with latest 3 amendment including - 1) Mounting stand for ELD and 2 fuse board to isolate from distribution board, for the following requirement of channels:. 24V DC - 1 to 4 channels 110V DC - 5 to 8 channels 110V AC - 9 to 12 channels. Inspection: RDSO.
2
133187
266374
Supply of Failsafe electronic time delay unit to operate on 24V DC Time setting 60 seconds as per RDSO Specn. No. RDSO/S.61/2000. Inspection: RDSO.
2
2031
4062
High precision MXL DLB pipe and cable locator: Digital multi frequency receiver based on advance digital signal processing with LED display for locating and avoidance of energized power cable and metallic utilities. consists of 4 modes-power, Radio, Generator and all scan modes. In addition to the instruments has 5 signal current measurements mode.(coverts to pipe and cable route tracer when used in conjunction with the optional MXT transmitter.also provide Depth measurement when used with ST-MTX)with built in data logging and storage capability and blue tooth data transfer High powered Multi frequency transmitter for frequencies into metallic pipe or cable to be route tracked by the MXL digital receiver. Complimentary equipment to the ST-MXL make: Stanlay or Equilant. Inspection: Consignee.
2
290640
581280
Supply of track feed battery charger to work on 110V/AC input to charge 1,2,3 lead acid cells of 80AH with 10A capacity with potential free contacts as per Spec No IRS: S.89/2013 version 1.0 or latest. Inspection: RDSO.
90
5775
519750
Supply of Colour light signal unit:
-
-
143824.68
M.S. Boom 65mm dia 9.5 mtrs long (dividing in two equilent two pieces nut & bolts arrangements, 8 pulling hand and boom locking arrangements etc. Boom pipe of size 80 mm dia of G.I length 10 Mtr long with 2mm thick (driving in two equivalent pieces with flange & fixing with nut & bolts arrangement, pulling handle and boom locking arrangements for pipe and as directed by engineer in charge at site (All materials to be supplied by the contractor). Inspection: Consignee.
4
9460
37840
Resting stand made up of C channel 150mm X 75mmX6mm thick for resting the boom movement frame/meeting post grouting type. Inspection: Consignee.
20
4730
94600
Boom movement rectangular frame made up by C channel 75mmX 37mmX6mm 9.5mtrs long and 10 250mm width (it should divided in two pieces nut and bolt arrangements) with necessary boom movement rollers arrangements and boom driving mechanism made up of 4 ball bearings, boom replacement arrangements etc. Inspection: Consignee.
4
16810
67240
M.S. Plate of size 20" X20'X6mm form boom locking arrangements with front and back covers( only E type locks will be supplied by Railways). Inspection: Consignee.
4
3610
14440
Supply of following furniture for station.
-
-
118876
Supply of Steel tubes galvanized ISI marked to IS:1239(part-1)/2004 in random 1 both end as per 14 IS:554 :1999 socketed at one end and another end protected with plastic protector. Socket confirming to IS.1239/part 2/1992 with amdt.1to 3(Re-affirmed 2002) Ncm, bore dia. 80mm, class: medium. GI.PIPE-80MM Make: TATA/JINDAL/SAIL. Per Unit =RMT. Inspection: RITES.
700
475
332808
Supply of Steel tubes galvanized ISI marked to IS:1239(part-1)/2004 in random 1 both end as per 15 IS:554 :1999 socketed at one end and another end protected with plastic protector. Socket confirming to IS.1239/part 2/1992 with amdt.1to 3(Re-affirmed 2002) Ncm, bore dia. 100mm, class: medium. GI.PIPE-100MM. Make: TATA/JINDAL/SAIL. Per Unit =RMT. Inspection: RITES.
1000
694
694400
Supply of printer Dot matrix 80 column, 24 pin, 300 CPS equivalent to TVS-MSP 450 champion or better. Inspection: Consignee.
2
9606
19212
Supply of Fiber boards of 'Alter the points immediately on arrival of the train as per GR:3.38 (2)' in bilingual i.e., in Hindi and English of size 4.5" X 12" . Inspection: Consignee.
2
281
562
1. Supply of basic material to construct unit maintenance free earth consisting as per RDSO spec 18 no. RDSO/SPN/197/2008 consisting of: a) copper bonded steel electrode of 3.0m long, 17.0 mm dia. with copper bonding thickness mini 250 micron and UL listed and marked--1 no. b)Earth enhancement compound of RDSO approved brand supplied in sealed bags of min 10 Kgs-03 No. c) Copper strip of 150X25x6mm to terminate earth rod-2 No. d) Copper strip of 300X25x6mm (MEEB)-1 No. Inspection: RDSO.
96
16837
1616352
PROVISION OF SMOKE DETECTION AND FIRE ALARM SYSTEM IN RELAY ROOM.
-
-
151424
Supply of Tips for ASM on panel operation boards, of size 16" x 18" in fiber sheet of 4mm thickness with glassy lamination. Inspection: Consignee.
2
1627
3255
Supply, Installation and Commissioning of Block proving By Axle Counter(BPAC) using block panel and UFSBI Double line operation as per RDSO Spec No:IRS-105/2012(VER.0) with latest version and amdt. Each set consisting of the following: (1) Universal Fail Safe Block Interface complete with all accessories as per RDSO 21 Spec:No:IRS-S-104/212(ver.0)with latest version & Amdt. - Qty-02 Nos.(2)Block Panel complete with all accessories as per RDSO Drg. No. RDSO/S/32017(latest amdts.)Qty-02 Nos.(3) Relay Rack duly wired with due locking and sealing arrangement as per RDSO Drg. No: RDSO/S/32018 including relays for each Relay Rack (QN1-19 Nos,QNA1-07 Nos,QL1-02 Nos, and Timers-01 No) - Qty 2 Nos.(4) Block Telephone with accessories as per RDSO spec. No: RDSO/SPN/191/2006 - Qty 02 Nos. Inspection: RDSO.
2
1065895
2131790
Supply and installation of OFC/Quad indication unit for UFSBI. Inspection: Consignee.
5
2478
12390
Supply of spare cards for UFSBI.
-
-
541814
Supply of Auto media changeover of modems working n redundant channels for data transmission on OFC/QUAD. Inspection: Consignee.
8
14297
114382.8
Supply of transformer rectifier 230V AC/24V DC, 1 AMP Capacity as per spec. IRS-S 91-93 with amendment-1 or latest. Inspection: Consignee.
2
1000
2000
Fabrication, Supply, and installation of powder coated cabinet, for the termination of power cables. The body of the cabinet to be made of 3mm thick. This includes sizing bending, providing holes 6mm dia. on flat 26 of size 3mm x 25mm for mounting 1 way PBTs and 40mm dia. holes on top & bottom surface. 6 Nos. on each side with provision of grommet bushes for cable entry, as per the drawing supplied by the railways. Color of powder coating as per instructions of site engineer in charge. All the materials will be supplied by the contractor except 1 way PBTs. Inspection: Consignee.
4
3040
12160
High Availability Single Section Digital Axle Counter System complete with dual sensor as per RDSO specification No. RDSO/ SPN/ 177/ 2012 version.3 with latest amendment. Phase reversal type with all accessories for complete system and required length of cable. Inspection: RDSO.
6
690000
4140000
Supply of Signal Conditioner Card(SCC1) for HASSDAC as per RDSO Specification No. RDSO/SPN/177/2012 with version 3 or latest. Inspection: RDSO.
3
29494
88483.5
Supply of Signal Conditioner Card(SCC2) for HASSDAC as per RDSO Specification No. RDSO/SPN/177/2012 with version 3 or latest. Inspection: RDSO.
3
29494
88483.5
Supply of Modem Card for HASSDAC as per RDSO Specification No. RDSO/SPN/177/2012 with version 3 or latest. Inspection: RDSO.
10
29494
294945
Supply of Micro Controller Logic Card for HASSDAC as per RDSO Specification No. RDSO/SPN/177/2012 with version 3 or latest. Inspection: RDSO.
3
79045
237136.5
Supply of Relay Driver Card for HASSDAC as per RDSO Specification No. RDSO/SPN/177/2012 with version 3 or latest. Inspection: RDSO.
3
29494
88483.5
Supply of DC-DC Converter Card for HASSDAC as per RDSO Specification No. RDSO/SPN/ 177/2012 with version 3 or latest. Inspection: RDSO.
3
17696
53090.1
Supply of Event Logger Card for HASSDAC as per RDSO Specification No. RDSO/SPN/ 177/2012 with version 3 or latest. Inspection: RDSO.
3
29494
88483.5
Supply of Web Detector(Each set consists of 2 nos. of Tx and 2 nos. of Rx Coils) for HASSDAC as per RDSO Specification No. RDSO/SPN/ 177/2012 with version 3 or latest. Inspection: RDSO.
6
40112
240675.12
Reset box for HASSDAC as per RDSO spec No. RDSO/SPN/177/ 2012 with version 3 or latest. etc., Inspection: RDSO.
6
42250
253500
Integrated OFC device MAPLE 4CS device 1U height & 19" rack mountable supporting E&M/FXO/FXS & Ethernet, with built in OFC ports supporting Single mode fibre for connecting stations/IBH on 38 dark fibre; Two E1 interfaces to be available with cross connection feature; unit support dual power supply DC main/Stand by DC or AC in lieu of DC through adaptor (AC-DC through adaptor to be supplied); E&M 2W/4W 08 port module to be provided, which is configurable; 10 port Auto phone module & 10 port hot line module & 100Mbps Ethernet to be available in the unit; Unit is SNMP complaint, MAKE: MROTEK/ WAVES/ FABIO. Inspection: Consignee.
4
176701
706807.8
Supply, installation and Commissioning of Block proving with digital axle counter as per RDSO Spec No: IRS S 105/2012 or latest using UFSBI and Block panel for single line operation. Inspection: RDSO.
1
1060000
1060000
Supply of spare cards for UFSBI.(Single Line).
-
-
143405
Supply of Automatic Media changeover of modems working n redundant channels for data transmission on OFC/Quad. Inspection: Consignee.
4
14297
57191.4
Excavation of pit, casting concrete foundation and erection of apparatus case full size as per Drg. No. SK/CN/1/89/A/1 and fixing of 1 No.of 'E' type lock for the front door, fixing of one hylam sheet of 1000mm X 940mm X 10mm thickness and painting the apparatus case inside and outside with one coat of redoxide and two coats of aluminium paints (foundation bolts and nuts,' E' type lock, cement, river sand, stone jelly of size 20/20mm, hylam sheet of size 1000mm X 940mm X 10mm, paints, varnish, fixing bolts and nuts and all other miscellaneous material required for the work shall be supplied by the contractor).
130
9875
1283750
Excavation of pit, casting concrete foundation and erection of apparatus case half size as per Drg. No.SK/CN/1/89/B/1, fixing one 'E' type lock for the front door and latching arrangements for the back door and 2 fixing of one hard wood shelf plank 37mm thick and painting the apparatus case inside and outside with one coat of redoxide and two coats of aluminium paints (foundation bolts and nuts, E type locks, cement, river sand, stone jelly of size 20/20mm, hardwood plank of 37mm thick, paints, varnish, fixing bolts and nuts and all other miscellaneous material required for the work shall be supplied by the contractor).
66
6967
459822
Excavation of pit, casting concrete foundation as per Drg. No. SC/N/CN@47>47@A/1 using metallic templates, for erection of Colour light Signals up to 4 aspects (foundation bolts, cement, river sand, stone jelly of size 20/20mm dia and all other miscellaneous materials required for the work shall be supplied by the contractor).
36
5008
180288
Erection of surface base, signal pole, mounting of Colour Light Signal up to 4 aspects complete on signal pole / offset bracket, (for LED / filament bulbs) with lenses, triple lamp holder, filament switching units, CLS transformers, current regulators (whichever is applicable), fixing of ladder with platform complete and concreting of ladder shoe, fixing of number plates, marker board, lenses guard, fixing of speed Limit board, whichever is necessary, termination tail cables, wiring of signal unit with PVC wire 3/0.75mm copper, provision of EWS locks, and painting of one coat of red oxide and two coats of aluminium/enamel paints. When the aspect is fixed on 4 offset bracket using 'U' bolts and nuts, a through bolt shall be provided by drilling of hole in the signal pole to prevent the offset bracket from sliding down. Item 4 Contd., (Supply of surface base, offset bracket, CLS pole, CLS aspect complete, ladder with shoes and platform, Speed limit board, LED aspects, current regulators, lamp holders, lamps, filament switching unit and CLS transformer is not covered in this schedule). ['U' bolts and nuts, through bolts and nuts, cement, stone jelly 20/25mm dia, river sand, Signal Colour Rings, wire PVCV 3/0.75mm copper, lens-guard, all fixing bolts and nuts, lead wood, paints PVC/Nylon sleeves, enamelled number plates, enamelled marker boards, EWS locks, and all other miscellaneous materials for the work shall be supplied by the contractor).
36
5501
198036
Excavation of pit and casting concrete foundation as per Drg. No. SC/N/CN@47>47@B/1 using metallic templates, for erection of GROUND TYPE Shunt signal. (Foundation bolts and nuts, cement, river sand, stone jelly of size 20/25mm and all other miscellaneous materials for the work shall be supplied by the contractor).
10
2519
25190
Erection of Ground type shunt signal complete including surface base, signal pole, LED aspects/Lenses, bulbs with holders (whichever is applicable), fixing of lens guards, number plate, termination of 6 tail cables, wiring of signal unit with PVC wire 3/0.75mm copper, provision of EWS locks and painting of one coat of red-oxide and two coats of Aluminium /.enamel paint, (Supply of Ground type shunt signal complete including surface base, signal pole, LED aspects, holder, bulbs and lenses is not covered in this schedule). [Wire PVC 3/0.75mm copper, lens guards, EWS locks, enamelled number plates, bolts and nuts, lead wool, paints and all other miscellaneous materials shall be supplied by the contractor).
10
2097
20970
Fixing of offset bracket using 'U' bolts and nuts erection of posts type shunt signal termination of tail 7 cables, provision of EWS lock and painting of one coat of red-oxide and two coats of aluminium / enameled paint. The work also includes drilling suitable holes on the CLS post and provision of a through bolt with nut to prevent the offset bracket from slipping down.
5
1613
8066.25
Fixing of junction type route indicator - 1 way to 6 way - complete / fixing of additional limb to the existing route indicators, termination of tail cables, wiring as per approved circuits diagram using wire PVC 8 3/0.75mm copper, provision of required number of EWS locks, wire mesh and painting. (Supply of junction type Route Indicators - complete and additional limb is not covered in this schedule). [3/0.75mm wire PVC fixing bolts and nuts, EWS locks, wire mesh, PVC/Nylon sleeves, paints and all other miscellaneous materials shall be supplied by the contractor].
-
-
10091.25
Fabrication and Supply of Powder coated Aluminum ladder of Size 38mmX38mmX5mm and 250 mm wide , with 38mm X5mm flat fixed at intervals of not more than 250 mm. All nuts, bolts, PVC sleeves, insulators etc. are to be arranged by the contractor. Per Unit =RMT. Inspection: Consignee.
160
518
82880
Supply fixing, wiring and commissioning of Fuse monitoring and Auto change-over system for 32 11 nos. of G-Type/Knife edge fuses up to 4A capacity, Type-I as per RDSO Spec. No. RDSO/ SPN/ 209/ 2012 Rev.1 or latest as per configuration prescribed by the Railways. Requires accessories for installation & wiring shall be arranged by Contractor. Wire coils will be supplied by Railway. Per Unit =Module. Inspection: RDSO
4
31800
127200
Design, Printing and making of display boards made with laminated wooden(NUWUD) sheet of 12mm thickness as per given description.
10
450
4500
Supply, painting and fixing of cable Gland Plate for full / half GKP box as per site requirement.
260
533
138580
Supply of approved quality of paint manufactured by Asian/British/Johnson and Nicholas accepted by DSTE/ASTE and Painting of all S&T gadgets in two coats duly scarping the rust as directed by SSE/SE at site, the colour to be used as per standard practice and as directed by SSE/SE at site.
900
78
70200
Supply and fixing of Netlon wire mesh of all windows and ventilators as per instructions of Engineer-in-charge including labour charges. Inspection: Consignee.
60
291
17460
Installation of Earth Leakage detector 12 channels.
2
8000
16000
Supply & laying of Double Wall corrugated HDPE pipe of size 78mm OD and 63 mm ID in 6 mtrs. Length bar along with one snapfit coupler for each bar confirming to IS:14930, Part-II Mark on it. Per Unit =RMT. Inspection of supply :RDSO.
1200
96
115920
Labour assistance for SE/JE in day to day works i.e checking the curves/straight alignment of 18 formation, levels etc. Carrying the tools & equipment etc. watch & ward during the course of execution of work as per the instructions of concerned SE/JE (As per Chief labour commissioner letter F. No.1/13(6)/2017-LS-II Dt.20.4.17). Per Unit =Per Day.
600
653
391800
Shifting of existing working functions like signals/Shunt/Calling on/Points/Track circuits etc., from old cable to new laid cables carefully without affecting the traffic under disconnection/blocks. Per Unit =Per Function.
570
1460
832200
Supply of LED indication system with 6 indications, Buzzer & Acknowledgement button with 20 interface facility to existing Datalogger and Modification of Datalogger embedded software when Master fails to set the point against occupied line within stipulated time after arrival of the train for the specified station. Per Unit =Per Stn. Inspection: Consignee.
2
40000
80000
Implementation, testing & commissioning of the above item 20 and as per the instructions of the in- charge. (All required materials for the work to be arranged by the contractor). Per Unit =Per Stn.
2
5000
10000
Transporting and supply and installation of Concrete (RCC) route indicators at intervals of 50 22 meters as per technical specification. They should be of standard RCC with letters " one side "SCR" and the other side "S&T cables" as per drawing SK 12/10 of RVNL/SC . In case of telecom quad cable joint locations it shall be painted with red color. Inspection: Consignee.
800
807
645600
Installation of single earth(maintenance free) including the following:- welding and fixing of copper tape (used as bus bar) welding of cadmium bronze cable to copper plate using material supplied. All the material supplied for mounting of copper tape, exothermic weld materials, tools and fixtures for welding copper tapes shall be arranged by contractor. for BPAC location. a. Digging /Auguring/Boring of single earth pit of 100mm to 125 mm dia. to the depth of approx. 2.8 meter. b. Insertion of 3.0 meter electrode and penetrating it at least .2 meter by 23 pushing gently with sledge hammer where the natural soil is assumed. c. Filling of earth pit with earth enhancement compound (EEC) in slurry from and backfilling. d. Carrying out exothermic weld connection on single earth electrode to a copper tape of 150X25X6mm. e. Carrying out exothermic weld connection on the copper tape of 150X25X6mm on earth electrode for connecting two 35 Sq mm cables for redundancy.. f. The exothermic welding material for bonding the earth system shall be procured from RDSO approved firms, which includes graphite moulds, clamps, weld metal powders. g. Digging a trench to a depth of at least 0 .5 Mtr. and run the two 35 Sq. mm earth conductor ( procured against supply item) from earth pit to MEEB. h. Routing and termination of two 35 sq. mm earth conductors in trench from earth pit to 300X25X6mm MEEB, which is to be fixed inside the equipment room with two insulation studs. i. 300X300X300 mm (inside dimension) concrete earth pit with a concrete lid, approx. 50mm thick with pulling hooks, shall be provided to cover the pit. Back side of the cover will be painted in black and dare of the testing and average resistance value shall be written.
90
4276
384840
Any other USSR 2019 items of SCR USSR as per the instructions of engineer in charge.
2
200000
400000
Supply and installation of SPD indicative type class 'D' , complete with enclosure and connecting wire/cables as per technical specifications. Make : OBO/Phoenix. Inspection :Consignee
-
-
330000
Provision of Security guards round the clock beet from UP Home Signal to DN Home Signal to avoid theft of signaling gadgets in 12hour shift. Per Unit =per 12 hours.
840
434
364560
Arranging unskilled workers with all tools for Non Interlocking working as per the instructions of engineer in charge.
400
231
92400
Arranging skilled workers for non Interlocking working with all tools and plants required as per instructions of engineer in charge.
400
308
123200
Laying GI pipes of 50/80/100 mm. dia. with coupling wherever required as per the railway requirement over the cement bridges, girder bridges, drainage culverts etc.,. The cables are to be taken through 29 pipes without causing any damage. GI Pipe will be supplied by Railways and all other materials shall be arranged by the contractor. The pipes he GI pipes are to be provided on MS channels with suitable fitting on Girder bridges without drilling holes on the girders and GI pipes are to be drilled with holes 6 nos. of 1/4" dia. per Mtr. and around the pipe before laying for 6 m. pipe in zigzag manner). Per Unit =RMT.
900
91
81900
Laying of DWC pipe of REX/Duraline/Tirupathi plasto of 120mm /103mm (or)180mm outer dia./153mm inner dia. (or) 250mm/217mm (or) 315mm/271mm inner dia. to IS spec. no. 14930 (part-II) for underground cables (6 mtrs.) in the excavated trench in all type of soils. Per Unit =RMT.
1200
25
30000
Supply and laying of DWC pipe made of polyethene of size 103mm inner dia. and 120mm outer dia. in 6mtrs. Length as per IS 14930 Part-II along with 1 coupler per pipe as per specifications IP 67 grade for every 6mtrs. Inspection : RDSO.
900
196
176400
Excavation of earth and providing earth pipe of size 50mm dia., 3.5mm thick 2.0 m. long G.I. pipe with masonry tub constructed around at earth locations as specified by site Engineer. Alternate layers of 30kgs- 32 char coal and 30kgs-common salt to be filled in the pit while closing. The pipe perforation etc., to be carried out as per drawing No. G/SG/09/2002. The earth pipe to be connected to the function with cable as supplied by Railways. Earth reading should be less than 03 Ohms The reading should be painted on the masonry tub. The masonry tub of 300X300X300mm should be covered with cement slab. ( All materials to be supplied by the contractor except cable.)
135
5100
688500
Fixing of Fiber TLJB.
600
352
211200
Excavation of pit of 400mm x 400mm x 1500mm at a given location and erecting rail posts of various lengths, plumbing and concreting it with cement concrete in the ratio of 1:3:6 with 40mm graded stone and river sand and curing the same. (Rails and cement will be supplied by the railways).
80
300
24000
Supply and fixing of protection arrangement to the pedestals and meeting posts of lifting barriers by providing MS Chain, 25mm ring, 10mm thickness of 1 meter length and fixing to the rail posts already available, drilling 12mm holes, fixing with 115mm x 12mm bolts and nuts and painting chain and rail posts.
4
2739
10956
Cutting of rails.
80
47
3760
Installation, testing and commissioning of Electrically operated lifting barriers with assembly, drive mechanism, motors etc. with control panel, boom locking arrangements & crank handles complete with Hand 37 generator as per detailed technical specification and instructions of site in-charge ( The above work included excavation of pits & concreting foundation for pedestal - 2 nos, excavation of pits & concreting foundation for gate meeting post-2 nos, Erection of Electric lifting barriers-2 set, fixing of ELB panel & it's wiring -1 no as per detailed technical specification and instructions of site in charge.
2
30000
60000
Supply of teak wood board for fixing 2 Nos of EKTs, with 2 Nos of push button, 6 nos. 10 mm LED resistance holders etc. (only EKTs will be supplied by Railways)
4
5725
22900
Fixing of sliding type mechanical boom, make assembly movement drive mechanism, resting 39 stand, meeting posts and fixing of E type locking plate to meeting post and in gate lodge as per the site in-charge instruction. NOTE: all required nut, bolts, chains, pad locks-2nos, and other miscellaneous items are to be supplied by the contractor. Rates included for all required nut & bolts, chains, padlocks 2 Nos and other miscellaneous are to be supplied by contractor. Per Unit =per LC gate (both booms).
2
23650
47300
Excavation of pit and concreting foundations for resting stand/meeting stand (approx. 10 Nos/item- 2).
4
16800
67200
Earth work in filling embankment.
600
164
98904
Supply & fixing of Hard drawn steel wire fabric 75 x 25 mm mesh of weight not less than 7.75kg. per Sq.. Including 60 x 20mm beading of country teak wood. Inspection: Consignee.
140
236
33110
Fabrication, supply, fixing of M.S. of size 10'X 18'X9' with locking arrangement for locking the boom in stand by mode.
4
3235
12940
Supply and fixing of retro reflective (High Intensive Prismatic : HIP) stop board made out of aluminium sheet 2 mm thick and lettering in three languages and fixing arrangements to boom pipe and as directed by engineer in charge at site.
4
3235
12940
Supply of paint approved quality and painting of sliding type boom, boom movement frame, resting stand, meeting post etc. as per regular standard practice with 2 coats of enamel paint black & Yellow colour with 12mm width retro reflective RED Yellow sticker.
4
5600
22400
Supply and filling sand as per the technical specifications.
65
615
39976.95
Painting of particulars of Glued Joint on rails/track circuit No. on TLJ boxes as per particulars 47 issued by Engineer in charge. Before painting on surface of the Glued Joint Rails/TLJ boxes shall be cleaned thoroughly. Painting shall be done with approved quality of stranded paints like Asian/Johnson/Nicholas /Berger etc., All the men and materials shall be arranged by the contractor the colors scheme shall be as per the instructions of Engineer in charge.
650
95
62075
Installation of smoke cum heat detector.
60
350
21000
Installation of Microcontroller based Fire Alarm monitoring, control unit & alarm hooter.
2
750
1500
Testing and commissioning charges for smoke cum heat detector.
2
600
1200
Fabrication and Supply of perforated GI FRAME for earthing of cable armour in FULL & Half 51 location boxes. This includes sizing, bending, holes drilling and galvanizing of MS flat as per the drawing supplied by railways. All materials will be supplied by the contractor.
-
-
114410
Releasing of relay racks complete with its wiring, relay base, supporting frames, cable ladder, indoor/outdoor cables etc. Axle counter wiring, Data logger and its wiring, panel and its wiring completely and any other miscellaneous wiring in relay/equipment/panel room etc., complete.
2
24882
49764
Laying and fixing of GI flat to the existing conventional earth to LB/Signal post by Arc/Gas welding as per the instructions of site engineer in charge. All men and materials shall be arranged by the contractor except G.I Flat. Per Unit =Per Location.
180
433
77940
Supply and fixing of cross on the signals (signal not in use) made of hard wood of size 1000mm x 100mm x 20mm (painted white as per SEM & suitable clamp made of MS flat. Inspection: Consignee.
44
328
14432
Wiring of point machine as per the wiring diagram duly disconnecting and rearranging the working 55 wiring as per instructions of engineer in charge and testing from new panel for all safety checks and restoring back the working wiring to the previous state and again testing the point for all safety check. The above work is to be carried out under traffic conditions duly observing train movements. All materials except wire coils and point TLJB is to be arranged by the contractor.
14
1577
22078
Testing of plain track circuits and point zone track circuits from track circuit location to station/cabin under traffic Condition duly disconnecting old wiring, bonding and reconnection of new wiring, bonding, and restore to normal working after testing.
28
569
15932
Supply and laying of PVC warning tape color Orange, width of 250mm (10") by printing with black letters (Indian Railway Signal / Telecom / OFC Cable on both sides of the tape). Inspection: Consignee.
15
30000
450000
Lifting/Shifting of existing Location box with foundation duly removing existing equipments, digging outdoor cable and refixing the same in the location box, after placing the location box at new location away from infringement as per the instructions of Engineer in charge .(All the materials to be arranged by the contractor).
60
2152
129164.4
Supply and installation of teak wood telephone stands with decolam sheet top capable of accommodation two telephones DRG. NO SK/S&T/89/276. Inspection: Consignee.
4
1293
5172
DOCUMENTATION RELATED ITEMS.
-
-
55080
Printing of A4 size cable path diagrams in original.
400
7
3000
Spiral binding of cable path (section - wise) diagrams into booklets. Per Unit =Booklet.
24
18
432
Providing and fixing fly proof galvanized MS wire gauge to windows and clerestory windows using galvanized M.S wire gauge with average width of aperture 1.4mm in both directions with wire of dia. 0.63mm with 2nd class teak wood beading 50.20mm.
120
568
68221.2
Videography of the work/Route.
17.5
310
5433.75
Survey of existing cable route both signalling and telecommunication cables with cable route tracer and marking the same with lime powder and marking tape to protect the working cables from being damaged.
10
994
9940
Flashing of Relay contacts of all types of plug in type relays with relay flashing equipment. This 66 work involves removing relays, flashing & reinserting, Recording of contact resistance. pick up values, replacing defective relays with good ones as supplied by the railways and carrying out random testing from panel etc., and submission of report along with serial number wise/Relay wise as per instructions of Engineer in charge Relay flashing equipment will be supplied by the Railways.
1100
28
30800
Arranging one skilled and one semi skilled technician to present at the Engg. digging activity to protect S&T cables.
360
539
194040
Arranging of skilled and un skilled workers with required tools during point blocks for removal of S&T assets to give way for T28 Machines and refixing the removed assets after insertion/removal of point. Per Unit =Per Point.
28
3178
88984
Clearing Bushes around the location boxes making necessary arrangements to approach the location boxes. Per Unit =Per Box.
130
498
64740
Filling of sand in the masonry cable duct made in relay rooms and plastering the same after taking all cables in side. Per Unit: Per Location.
8
12530
100240
Fabrication & supply and fixing of stay rods for wiring support at location boxes, CT rack etc., this includes providing of sleeve to stay rod, fixing bolts, nuts & washers etc as required at site.
850
265
225675
HASSDAC - Installation Installation, energization, testing & commissioning charges with dual detection the work consists of i)Fixing of Axle counter track device consisting of Tx-Rx coil assembly for each detection point 2 in Up direction & 2 in Down direction. Total-4 in double line section) by drilling holes in the rails as per the marking given by the site in-charge. (Note: Tx-Rx coil assembly and rail mounting fixtures are covered 73 under supply of single section digital axle counter) ii) Fixing of Rail deflector plates on either side of each detection points as per the marking given by the site in charge. iii) Fixing of evaluators inside pre-erected location boxes on the nominated planks along with VR assembly duly providing anti vibration arrangement as per the instructions of site in charge. iv) Routing cables from Tx/Rx coil assembly through pre laid GI pipe/HDPE pipe arrangement of track crossing and entering termination box and termination. Note: Rs. 10000/- will be released after installation & testing, Remaining amount will be released after completion of field training for minimum 10 persons.
5
56180
280900
Supply and installation of wago connectors FTB set. Per Unit =Per Location. Inspection: Consignee.
10
2000
20000
Supply and installation of wago connectors UFTB set (Un-fused terminal block). Per Unit =Per Location. Inspection: Consignee.
10
1800
18000
Supply and installation of wago connector End Plate set (End Clamp) Per Unit =Per Location. Inspection: Consignee.
10
1300
13000
Supply and installation of Din Rail. Per Unit =Per Location. Inspection: Consignee.
10
350
3500
Installation of MAPLE 4C or Similar Equipment from Reputed system at station for BPAC working on OFC.
2
8427
16854
Fabrication, Supply & fixing of reset box stand made 1' X 1' L angle to fix reset box with powder coating & hylam sheet. Inspection: Consignee.
5
2832
14160
Provision of ring earth by connecting conventional earths with copper catenary wire as required at 80 site as per instructions site in charge. Excavation of earth and providing earth pipe of heating gravity of size 50mm dia, 3.5mm thickness, 2.0m long GI pipe of heavy quality along with masonry tub constructed around at earth locations as specified by site Engineer. Alternate layers of charcoal and common salt to be filled in the pit while closing. The pipe perforation etc., to be carried out as per drawing No.G/SG/09/2002. The masonry tub of 400X400X450mm. 50mm thickness should be cover with cement slab to be provided each conventional earth. Masonry tube shall be filled with river sand after completion of earthing. Conventional earths to be wrapped with catenary wires before excavated in earth along with use of proper clamps and nuts. All earths to be connected with each other by use of copper catenary wire or suitable cable provided by railways. Minimum two number earth pipe to be connected inside the location/function with suitable cable(cable will supplied by railways). Excavation of trench of 0.5m minimum depth for inter connection of 4 conventional earths by catenary wire. Catenary wire should be welded through are welding to the GI pipe with copper clamps. The earth reading. D.O.I & D.O.M. should be painted on the masonry tub.(All the men and the materials to be supplied by the contractor except catenary wire.)
10
18445
184450
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements