Get tender documents at just ₹200 per tenderKnow More
Search made simple for latest tendersNo hidden charges. No keyword restrictionsExplore Our Plansor Pay Per Tender

Bid Number: GEM/2019/B/348830 Dated: 09-09-2019 Bid Document Bid Details Bid End Date/Time 20-09-2019 09:00:00 Bid Life Cycle (From Publish Date) 90 (Days) Bid Offer Validity (From End Date) 30 (Days) Ministry/State Name Ministry Of Defence Department Name Department Of Defence Organisation Name Indian Army Office Name Od Fort Allahabad Total Quantity 667900 Item Category Stainless steel safety razor blades MSE Exemption For Years Of Experience And Turnover Yes Startup Exemption For Years Of Experience And Turnover Yes Bid to RA enabled No Stainless Steel Safety Razor Blades ( 667900 pieces ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Bid Requirement (Allowed Values) Dimensions Types (in mm) Medium (0.100 ± 0.005) * Material The material used for razor blades shall conform to IS: 9294-1979 Yes * Workmanship and finish Cutting edges: Both sides of the blade at the cutting edge shall be honed and stropped When viewed under a magnification of 100 X, the final honing bevel Yes * 1 / 4 shall either be hollow or flat, smooth and continuous, throughout the lenght of each edge and shall be free from marks made by grinding and rough honing operations The initial intermediate (if present ) and the final bevels shall be seperate and parallel to the cutting edge of the blade When view under a magnification of 100 X, the cutting edge of the blade shall be free from defects like bend edges, jagged edges, honed edge gouted out, one side not honed and bent over edge Yes * Any nick 0 point 01 mm or smaller, or any nick appearing in the chamfered or curved postion at the ends of the cutting edges shall not be counted but a series of nicks (0 point 01 mm or smaller) forming a serrated edge or unhoned cutting edge shall not be permitted Yes * Straightness and parallelisum of cutting edges: When checked on the top of cutting edge along the full length of the blade, each cutting edge shall be straight to within 0 point 04 mm The two cutting edge shall be parallel to within 0 point 08 mm so that when measured at the two end and at least three intermediate postion, there shall not be variation in excess of 0 point 08 mm in the maximum and minimum Yes * 2 / 4 perpendicular measurement between the two cutting edges Finish: The blade, when it reaches the consumer, shall be in a clean and new condition, free from dirt and dust Yes * Marking Each blade or the dispenser shall be legibly and indelibly marked with the manufacturer's name or trade-mark or identification mark The blade and/or its wrapper or dispenser shall also be marked with the word "stainless steel" or "stainless" Yes * The outer packing of each blade may also be marked with the ISI certification mark Yes * Packing The packing shall be in accordance with the acceptable trade practice or as agreed to between the purchaser and the supplier When the blades shall not having any marking they shall be packed in temper proof dispenser Yes * Certification Conforming to IS:7371(Latest) YES * Whether ISI Marked YES * CM/L Number(Must declare if ISI Marked) NA * Test report details Availability of Test Report from Central Govt/NABL/ILAC accredited lab to prove conformity to specification No * Test Report to be submitted to the Buyer on Demand write NA if Test report is not available NA * 3 / 4 * Bold specifications are the golden parameters. * Bidders may note that In respect of non-golden Parameters, the specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer. Consignees/Reporting Officer and Quantity S.No. Consignee/Reporti ng Officer Address Quantity Delivery Days 1 S M Tripathi 211005,Ordnance Depot, Fort Allahabad, Near Bairahana 667900 15 EMD Detail Required No ePBG Detail Required No Splitting Bid splitting not applied. Buyer Specific Additional Terms

Disclaimer: BidAssist has made every reasonable effort to ensure that the information is accurate and authentic however it cannot be held liable for any third-party claims or losses of any damages. BidAssist makes no warranty, expressed or implied, as to the results obtained from the use of the information. If you think you may have noticed any error or omission, please let us know by contacting contact@bidassist.com.