Military Engineer Services Tender

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

Taking down chowkat or frame with shutters including fitting and fixtures area not exc 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats complete all as specified and directed by Engineer-in-charge.

Taking down chowkat or frame with shutters including fitting and fixtures area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats complete all as specified and directed by Engineer-in-charge.

Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each (includig fitting and fixtures) complete all as specified and as directed by Engineer-in-charge.

Taking down shutters of any description not exc 1 Sqm (includig fitting and fixtures) complete all as specified and as directed by Engineer-in-charge.

S&F 30mm thick flush shutter solid core construction with block board core & ply wood face panels, commercial type on both faces including necessary fitting like 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) (02 Nos in each shutter), 250mm long aluminium alloy anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked)(01 No in each shutter), 150mm long SS handles, (ISI marked) (02 No in each shutter), floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring overall length of cover plate 140mm (ISI marked), Mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate fixed to wooden frame or welded to steel frame making suitable cut out in wall and making good in CM 1:4 (01 No in each shutter) and 100mm size B-21 butt hinges of extruded aluminium alloy (02 Nos in each shutter) inclusive of magic eye complete all as specified and directed by Engineer-in-charge. Note : Rate of all required fitting are included in this item, Nothing extra shall be paid on this account.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) complete all as specified and directed by Engineer-in-charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm double rebated comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be inclusive in this items) complete all as specified and directed by Engineer-in-charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm single rebated comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be inclusive in this items) complete all as specified and directed by Engineer-in-charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F providing factory made 18mm thick 100% solid WPC (Wood Polymer Composite) laminated finish shutter of required size comprising of virgin K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives made from Extrusion process WPC foam sheet single extruded (inner) with having minimum density of 650 kg/cum manufactured by a ISO 9001-2015 certified company, having good screw holding capacity (screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be lamintated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel piano hinges of required size with necessary full body threaded star headed counter sunk S.S screws all as per direction of Engineer-in-Charge.

M&L for solid PVC sheet for 18mm width & 3mm thick PVC coloured lipping of approved design & colour fixed with solvent cement or headless nails complete all as specified and directed by Engineer-in-charge.

S&F 35mm thick factory made glazed and skeleton shutters made of second class hard wood (Bonsum/Hollock), open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Part I Section 8 Clause 8.24 (a) kiln seasoned and chemically pressure treated fixed to chowkat complete all as specified and directed by Engineer-in-charge.

Supply and fixing 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 including necessary fitting like 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked)(02 Nos in each shutter), 300mm long aluminium alloy anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked) (01 No in each shutter), 150mm long brass handles, (ISI marked)(02 Nos in each shutter), 100mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin, anodized type B-21 (ISI marked) (02 Nos in each shutter), magic eye, aldrop complete all as specified by the manufacturer and as per directions of Engineer- in-charge

Providing and fixing factory made uPVC white colour casement (Openable) window area exceeding 1.00 sqm but not exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges of'zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass complete all as specified directed by Engineer-in-Charge Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid inclusive in this item). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be mad

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be inclusive in this item) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified & shown in relevant drawing of item No. 08095 in MES Schedule (Part-II) and directed by Engineer-in-Charge

S&F 30mm thick factory made solid core PVC door shutter (style) consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in mild steel frame welded/ sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement, complete, all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and including necessary fitting like 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked)(01 No in each shutter), Aluminium locking bolts anodised, with bolt not less than 10mm dia, 150 mm size (01 No in each shutter), 150mm long extruded aluminium handles, anodised, fabricated type (ISI marked)(02 Nos in each shutter), 75mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin, anodized type B-21 (ISI marked) (03 Nos in each shutter) complete all as specified and directed by Engineer-in-charge.

M&L for providing 30mm thick factory made prelam plain wire mesh solid PVC door shutters consisting of frame made out of MS tubes of 19 gauge thickness and size of 19mmx19mm for stile and 15mmx15mm for top, lock & bottom rails MS frame shall have a coat of metal primer of approved make and manufacturer, 19mmx19mm M.S square tubes shall be covered with heat moulded prelam sheet, C channel made from 5mm thick PVC sheet of density 600 kg/Cum of size 30mm thickness, 115mm width out of which 100 shall be flat and 15mm shall be bent in 90 degree angle on either side forming stiles, one of the 90 degree bend edge is cut from stiles as well as rails to nail from inner side of door to hige wiremesh fixing steel screws. 5mm thick 140mm wide PVC sheet out of which 125mm shall be flat and 15mm shall be bent in 90 degree on the inner side to form top and bottom rail and 155mm wide PVC sheet out of which 100mm shall be flat and 15mm shall be betin 90 degree on both side to from lock rail. An additional 5mm thick PVC strip of 20mm diwth is to be stuck on the iterior side of the 'C' Channel using PVC solvent cement adhesive. panel will be of ss wire mesh of 24 gauge to be fitted inside area of stiles & rails, the wire mesh in top, bottom & lock rails sealed with 15mm x 15mm tube with steel screw of size 13/6mm. 10mm (5mmx2 Nos) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail door to be fiexd to frame with 3 Nos MS Powder coated butt hinges size 100mm x 25mm x 2mm and 32 mm long steel screws drilled suitable to pass through both the walls of M.S. tube other hardware should be fixed with 19x6mm size steel screws etc. complete as per direction of Engineer-in-Charge, maufacturer's specification & drawing. Note :- All hardware are deemed to be included in quoted rates including door spring, tower bolt, Aldrop bolt.

S&F 150 mm long mild steel barrel tower bolt stove enamelled black with bright bolt (ISI marked) complete all as specified & directed by Engineer-in-Charge.

M&L for 100mm bright finish chromium plated steel handles of approved shade and design fixed with cadmium coated screws on the kitchen cabinet drawers complete all as specified and directed by Engineer-in-charge..

S&F 250mm long mild steel sliding door bolts clip type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate (ISI marked) complete all as specified & directed by Engineer-in-Charge.

S&F 150 mm long mild steel pressed handle, oval type, stove enameled black (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F 200mm long powder coated aluminium American handles, anodised, cast type (ISI marked) complete all as specified and directed by Engineer-in-Charge

S&F 150mm long stainless steel deisigner handle fixed with cadmium plated screws (ISI marked) complete all as specified and directed by Engineer-in-Charge

S&F as in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made out of mild steel heavy duty & fixed (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S&F as in repair stainless steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed by Engineer-in-Charge.

M&L for brass mortice lock set with handles 175mm and 6 lever locking mechanism complete all as specified and directed by Engineer-in-charge.

S&F as in repair bright finished brass 100mm mortice slatch and lock with four levers and pair of anodized (anodic coating 10 mircron) as per IS-1868 aluminium lever handles with necessary screws etc complete all as specified and directed by Engineer-in-charge.

M&L for 1.5mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed by Engineer-in-Charge.

S&F as in repairs stainless steel drapery rod of 25 mm inner dia (in lengths as directed) with & including decorative finial at both ends and pair of stainless steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam including making good disturbed surface with 1:3 cement plaster and finishing treatment of existing wall quality complete all as specified & as directed.

S&F as in repair Mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate fixed to wooden frame or welded to steel frame making suitable cut out in wall and making good in CM 1:4 complete all as specified and directed by Engineer-in-charge.

S&F as in repair 0 degree clip type self closing hinges for kitchen cupboards fixed with cadmium coated screws as per manufacturer instruction complete all as specified and directed by Engineer-in-Charge

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge.

Material & Labour for providing and fixing stainless steel (Grade 304) railing /grill made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed by Engineer-in-Charge. Note :- Drawing for the same is enclosed with tender documents.

S&F anodised aluminium frames powder coated (thickness of powder coating shall not less than 50 micron) for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified and directed by Engineer-in-Charge.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge

S&F telescopic channel steel ball 20" to 24 " drawer side channel of standard size and incl of roller for moving drawer mild steel bright finished or electrogalvanised complete all as specified & directed by Engineer-in- charge.

S&F kitchen perforated cutlery SS basket grad 304 4" fixed in kitchen drawer including 2 Nos 22" telescopic channel of appropriate length fixed cupboard material complete all as specified & directed by Engineer-in- charge.

S&F kitchen cup and saucer SS basket grad 304 6" fixed in kitchen drawer including 2 Nos 22" telescopic channel of appropriate length fixed cupboard material complete all as specified & directed by Engineer-in- charge.

S&F kitchen thali SS basket grad 304 8" fixed in kitchen drawer including 2 Nos 22" telescopic channel of appropriate length fixed cupboard material complete all as specified & directed by Engineer-in- charge.

M&L for 18-20mm thick Granite slab of approved shade and colour as in cooking platforms, steps, jambs, pillars, window cills and the like etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) over & including 15mm thick screed bed (bedding layer) in CM (1:6) complete all as specified and directed by Engineer-in-charge. Note : The exposed edges of granite stone slab shall be made full round & polished to mirror finish and rate quoted shall deemed to include this provision.

M&L for 15mm thick rendering in cement mortar (1:4) on fair face surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement including preparation of newly plastered surface of walls & applying two coat cement base paint over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-charge. Note : Plaster shall be carried out in patches and contractor shall have no claim for any height and scaffolding what so ever is the location.

M&L for 10mm thick rendering in cement mortar (1:6) on fair faced surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement including preparation of newly plastered surface of walls & applying two coat OBD over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-charge.

M&L for 10mm thick rendering in cement mortar (1:6) on fair faced surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement including preparation of newly plastered surface of walls & applying two coats white wash complete all as specified and directed by Engineer-in-charge.

M&L for complete removal of existing treatment from old plastered surfaces like lime, distemper, plastic paint, cement base paint including scrapping down smoke soot, moulds, moss, efflorscent salts, trading oil, greasy spots using mechanical grinding machine and washing of old surface with water including filling of cracks and applying two coats of cement base paint shade/tint over a coat of cement base primer on walls complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge.

S&F 5.5mm thick obscured or frosted glass pin head type and glazing with EPDM neoprane gasket in square exc 0.5 sqm in each pane complete all as specified and directed by Engineer-in-charge.

S&F 5.5mm thick sheet glass ordianary quality glazing with oil putty in squares, area exceeding 0.50 Sqm in each pane area complete all as specified and directed by Engineer-in-Charge .