Military Engineer Services Tender
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Costs
EMD
₹ 92,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_680294_1Bid Award Id
ViewTender No
8646/A/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
M&L for dry tibba sand in trenches for cushioning to under ground cable spreading, levelling, hand punning complete all as specified and directed.
Note- Punned down thickness will be measured for payment purpose.
229
-
-
Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250mm x 150mm x 40mm complete all as specified and directed.
18870
-
-
Disconnecting and Taking out of old LT armored PVC cables of any size/core/any voltage grade from trenches for replacement complete all as specified and directed.
3330
-
-
Supply, laying, testing and commissioning cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, elecric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 Sqmm 4.0 core complete all as specified and directed.
Note:- (i) Cable may be laid in trenches, under road, across the Nallah, along poles/walls and ducts etc.
(ii) Excavation, earthwork, sand cushioning, cable cover, pipe for cable protection to be measured and paid separately.
400
-
-
Supply, laying, testing and commissioning cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, elecric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sqmm 3.5 core complete all as specified and directed.
Note:- (i) Cable may be laid in trenches, under road, across the Nallah, along poles/walls and ducts etc.
(ii) Excavation, earthwork, sand cushioning, cable cover, pipe for cable protection to be measured and paid separately.
500
-
-
Supply, laying, testing and commissioning cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, elecric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 core complete all as specified and directed.
Note:- (i) Cable may be laid in trenches, under road, across the Nallah, along poles/walls and ducts etc.
(ii) Excavation, earthwork, sand cushioning, cable cover, pipe for cable protection to be measured and paid separately.
700
-
-
Supply, laying, testing and commissioning cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, elecric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 50 Sqmm 3.5 core complete all as specified and directed.
Note:- (i) Cable may be laid in trenches, under road, across the Nallah, along poles/walls and ducts etc.
(ii) Excavation, earthwork, sand cushioning, cable cover, pipe for cable protection to be measured and paid separately.
500
-
-
Supply, laying, testing and commissioning cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, elecric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 70 Sqmm 3.5 core complete all as specified and directed.
Note:- (i) Cable may be laid in trenches, under road, across the Nallah, along poles/walls and ducts etc.
(ii) Excavation, earthwork, sand cushioning, cable cover, pipe for cable protection to be measured and paid separately.
400
-
-
Supply, laying, testing and commissioning cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, elecric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 95 Sqmm 3.5 core complete all as specified and directed.
Note:- (i) Cable may be laid in trenches, under road, across the Nallah, along poles/walls and ducts etc.
(ii) Excavation, earthwork, sand cushioning, cable cover, pipe for cable protection to be measured and paid separately.
400
-
-
Supply, laying, testing and commissioning cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, elecric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 120 Sqmm 3.5 core complete all as specified and directed.
Note:- (i) Cable may be laid in trenches, under road, across the Nallah, along poles/walls and ducts etc.
(ii) Excavation, earthwork, sand cushioning, cable cover, pipe for cable protection to be measured and paid separately.
430
-
-
S& F in replacement aluminium cable lug of size of cable lug 25 sqmm complete all as specified and directed.
20
-
-
S& F in replacement aluminium cable lug of size of cable lug 35 sqmm complete all as specified and directed.
20
-
-
S& F in replacement aluminium cable lug of size of cable lug 50 sqmm complete all as specified and directed.
24
-
-
S& F in replacement aluminium cable lug of size of cable lug 70 sqmm complete all as specified and directed.
20
-
-
S& F in replacement aluminium cable lug of size of cable lug 95 sqmm complete all as specified and directed.
16
-
-
S& F in replacement aluminium cable lug of size of cable lug 120 sqmm complete all as specified and directed.
16
-
-
S& F in replacement aluminium cable lug of size of cable lug 150 sqmm complete all as specified and directed.
16
-
-
S& F in replacement aluminium cable lug of size of cable lug 185 sqmm complete all as specified and directed.
16
-
-
S&F in replacement aluminium crimping connectors of size of crimping connectors 25 sqmm complete all as specified and directed.
8
-
-
S&F in replacement aluminium crimping connectors of size of crimping connectors 35 sqmm complete all as specified and directed.
8
-
-
S&F in replacement aluminium crimping connectors of size of crimping connectors 50 sqmm complete all as specified and directed.
8
-
-
S&F in replacement aluminium crimping connectors of size of crimping connectors 70 sqmm complete all as specified and directed.
8
-
-
S&F in replacement aluminium crimping connectors of size of crimping connectors 95 sqmm complete all as specified and directed.
8
-
-
S&F in replacement aluminium crimping connectors of size of crimping connectors 120 sqmm complete all as specified and directed.
8
-
-
S&F in replacement aluminium crimping connectors of size of crimping connectors 150 sqmm complete all as specified and directed.
8
-
-
S&F in replacement aluminium crimping connectors of size of crimping connectors 185 sqmm complete all as specified and directed.
8
-
-
M&L for cutting of road / hardstanding upto a size not exceeding 20 cm in width and not exceeding 60 cm in depth for laying of LT UG cable protection pipe line and finished surfaces by extracted material and provided with 150mm thick PCC (1:3:6) type C-2 as top layer to match the existing surfaces and remove surplus extracted material 50 m away complete all as specified and directed.
50
-
-
S&F 50 mm bore tube, 'light grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.
60
-
-
S&F 40 mm bore tube, 'light grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.
62
-
-
M&L for making of surface for painting duly scrubing the existing paint and applying two coats of synthetic enamel paint over a coat of red oxide primer for LT panel board/Feeder piller box of any size/type at various location complete all as specified and directed.
35
-
-
M&L for servicing to Outdoor/Indoor type LT panel Board of any capacity/size by replacing pitted portion area not exceeding 1.0 sqm with suitable gauge of MS sheet,welding work,replacement of unservicable door hinges and locking arrangement complete all as specified and directed.
8
-
-
S&F in repair Adjustable thermal & Adjuatable magnetic setting MCCB four pole 63 Amps, 16 KA rating,Ics=75% Icu ,415 volts AC complete all as specified and directed.
12
-
-
S&F in repair Adjustable thermal & Adjuatable magnetic setting MCCB four pole 125 Amps, 16 KA rating,Ics=75% Icu ,415 volts AC complete all as specified and directed.
16
-
-
S&F in repair Adjustable thermal & Adjuatable magnetic setting MCCB four pole 160 Amps, 36 KA rating, 415 volts AC complete all as specified and directed.
12
-
-
S&F in repair Adjustable thermal & Adjuatable magnetic setting MCCB four pole 200 Amps, 36 KA rating, 415 volts AC complete all as specified and directed.
10
-
-
S&F in repair Adjustable thermal & Adjuatable magnetic setting MCCB four pole 250 Amps, 36 KA rating, 415 volts AC complete all as specified and directed.
10
-
-
S&F in repair Adjustable thermal & Adjuatable magnetic setting MCCB four pole 350/400 Amps, 36 KA rating, 415 volts AC complete all as specified and directed.
7
-
-
S&F in repair Adjustable thrmal & Adjuatable magnetic setting MCCB four pole 630 Amps, 50 KA rating, 415 volts AC complete all as specified and directed.
4
-
-
S&F in replacement isolator four pole 125 Amp, C curves MCB repturing capacity 16 KA complete all as specified and directed.
4
-
-
S&F in replacement MCB TPN 63 Amp, C curves MCB repturing capacity 10 KA complete all as specified and directed.
13
-
-
S&F in replacement MCB SPN 40 Amp, C curves MCB repturing capacity 10 KA complete all as specified and directed.
20
-
-
S&F in replacement MCB SP 6-32 Amp, C curves MCB repturing capacity 10 KA complete all as specified and directed.
60
-
-
S&F in replacement of volt meter 0-500 Volt digital type square 96 sq mm lamp accurracy glass complete all as specified and directed.
8
-
-
S&F in replacement of Ammeter 0-200 Amp digital type square 96 sq mm lamp accurracy glass complete all as specified and directed.
8
-
-
S&F in replacement power contactor 415 Volt, 50 HZ, 3 phase, type 400 Amp suitable for fixing in AMF panel of DG of capacity 200 KVA complete all as specified and directed.
2
-
-
M&L for earthing complete with copper earth plate 600 mmx600 mm x3.15 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including copper strip 20x3mm by means of bolts, nuts, check nuts and washers of copper/brass including providing of alternate layer from bottom edge to 30cm above top edge of earth plate by chemical fill compound, ground enhancing material, earth powderand after that 1 m back of layer of charcoal dust and common salt including PCC pit in PCC (1:2:4) type B-1using 20 mm graded crushed stone aggregate, RCC frame with 40mm thick RCC cover reinforced with 8mm dia deformed bars handle including excavation and earth work in any type of soil and medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 40mm bore main board complete all as shown in electrical plate No 3 connected to main control board all as specified and testing on completion including dismantling of old earth plate complete all as specified and directed. Note: (i) Excavation, earthwork, charcoal, PCC pit is covered under this item.
(ii) Contractor shall be produced the result of earth below 1 Ohm othrewise earthing will not be acceptable.
10
-
-
S&F in replacement LED aviation obstruction light 6/7 watt with light dependent sensor, IP:65 protected complete all as specified and directed.
4
-
-
S&F in replacement LT cable straight through jointing kit heat shrink type of 70 to 150 Sqmm cable size complete all as specified and directed.
20
-
-
S&F in replacement CT coil suitable for Amp metre 100/5 Amp complete all as specified and directed.
16
-
-
S&F in replacement indicating lamp set RYB for phase indication operating 240 Volt 50 Hz AC with new one LED panel mounting type as per existing make and type complete all as specified and directed.
20
-
-
Supplying, installing, testing and commissioning factory made outdoor type cubical feeder pillar box of size 1000mm x 800mm x 400mm made out of MS sheet of 3.15mm thickness outer sheet and inner sheet thickness 2.00mm suitable for 3 phase, 4 wire, 415 volts, 50 Hz from CPRI approved having aluminium busbar 400mp 3 phase 4 wire system, 415 volts, factory made in an approved factory having to seven tank treatment process for powder coating with thickness not less than 60 microns provided with suitable gasket to make it dust/weather and vermin proof suitable for opening both side with locking arragement and general condition confirming to IS: 8623/93 mounted on suitable PCC (1:2:4) type B1 using 20 mm graded stone aggregate foundation comprising including taking down old feeder pillar box complete all as specified and directed.
2
-
-
Supply, installation, commissioning and testing in replacement of LT panel board CPRI approved ,(415 Volts, 50 Hz , 3-phase, 4 wire supply) floor mounted , factory assembled, outdoor type weather and vermin proof (Protection Class IP-54) made out of 40mm x 40mm x 6 mm angle iron frame of size 1.5 mtr height and 3.15 mm thick MS Sheet CRCA sheet with both side hinged opening for external, rubber lining, locking arrangement, painted externally and internally with two coats of synthetic enamel gray paint First Quality) over a coat of red oxide primer complete including grouting of frame with PCC (1:2:4) type B-1 of block size 30x30x30 cm for installation of panel complete all as specified and directed and including the following:-
(a) MCCB 415 Volts, 400 Amp rating 4 Pole, Service Breaking Capacity 35/36 kA -1 No. (b) MCCB 415 Volts, 200 Amp, rating 4 Pole, Service Breaking Capacity 25 kA-2 No(Out going)
(c) MCCB 415 Volts, 100 Amp, rating 4 Pole, Service Breaking Capacity 25 kA-1 No(Out going)
(d) MCCB 415 Volts, 100 Amp, rating 4 Pole, Service Breaking Capacity 25 kA-2 No(Out going)
(e) CTs 500/5 ma -1 set of 3
(f) Digital panel metre class 1 with 3 Phase Voltage, current Frequency, PF, KW, KVA, KVAR and KWh-1 No
(g) Aluminium bus bars 500 Amp -1 set of 4
1
-
-
M&L for Earthing complete with galvanized steel earth plate electrodes 600 mmx600 mm x 6 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including galvanized GI strip 25X4mm by means of bolts, nuts, check nuts and washers of galvanized iron and steel including PCC pit in PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregate, RCC frame with 40mm thick RCC cover reinforced with 8mm dia deformed bars handle. including excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 40 mm bore main board complete all as shown in electrical plate No 3 connected to main control board all as specified and testing on completion including dismantling of old earth plate complete all as specified and directed. Note: (i) Rate of excavation, earthwork, charcoal, PCC pit is covered under this item.
(ii) The unit rate includes for protection pipe and GI strip 25 x 4mm from top of earth plate up to 7.5 meter above ground level.
20
-
-
M&L for Earthing complete with galvanized steel earth plate electrodes 600 mmx600 mm x 6 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including galvanized GI strip 32X6mm by means of bolts, nuts, check nuts and washers of galvanized iron and steel including PCC pit in PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregate, RCC frame with 40mm thick RCC cover reinforced with 8mm dia deformed bars handle. including excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 40 mm bore main board complete all as shown in electrical plate No 3 connected to main control board all as specified and testing on completion including dismantling of old earth plate complete all as specified and directed. Note: (i) Rate of excavation, earthwork, charcoal, PCC pit is covered under this item.
(ii) The unit rate includes for protection pipe and GI strip 32 x 6mm from top of earth plate up to 7.5 meter above ground level.
10
-
-
M&L for Sub main wiring with 2 runs of 4 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLSH 1100 volts grade cable drawn through PVC casing caping and including PVC casing caping on wall/roof and one run of 4 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLSH 1100 volts grade cable as earth conductor including taking down old unsv submain wiring complete all as specified and directed. Note : Two runs of 4 Sqmm cable, one run of 4 Sqmm earth conductor and one run of PVC casing caping shall be measured and paid as one unit length.
90
-
-
Dimantling of existing unserviceable PCC pole of any size and type from its position from the site and taking away from site including necessary excavation and earth work in any type of soil, demolition of concrete, disconnecting of street light fitting ect complete all as specified and directed.
3
-
-
Supply, erecting & fixing in true vertical position Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31 (9.00 metres long) confirming to relevent IS including one coat of primer of red oxide and two coats of aluminium paint and two coats of bituminous paint inside and out side of bottom portion up to 1.8 mtr length complete all as specified and directed.
3
-
-
S&F in repairs for rigid non-metallic PVC conduit of 20 mm dia heavy duty alongwith street light poles for wire from junction box to light fittings including fixing arrangement complete all as specified and directed.
105
-
-
M&L for LT Cable junction box outdoor shall be made out of Polycarbonate with glass fiber reinforced and size should be not less than 205mm x 255mm x 112 mm(upto Cable Size 35/25 Sqmm). The Polycarbonate Junction Box shall be environment friendly, recyclable, halogen & silicon free, anti acid & anti corrosive. The Junction Box shall be rated for degree of ingress protection IP 66/69 in accordance with IEC 60529.Weather proof, UV-resistant, rainwater-proof, temperature-resistant. The gasket material of junction box shall be Polyurethane and the gasket shall be internally embedded. The Junction Box shall be complies with requirements of the standards IEC 60998 - 1, IEC 60670 - 22 & IEC 60670 - 2 - 5. The Junction Box with Connectors or Terminal Trip or Bus Bar. The manufacturer of Junction Box / Enclosure shall submit a copy of IEC Certificate . For better safety the Polycarbonate enclosure and shall be fire retardant & self - extinguishing in accordance with IEC 60695 - 2 - 11, DIN VDE 0304 Part - 3, UL Subject 94 for Flammability V-2. It should be tested at Glow Wire test for 960 degree Centigrade & Current Carrying Capacity upto 102 Amp. The impact strength of Polycarbonate enclosure / boards i.e. the Degree of protection against mechanical load shall be in accordance with EN 50298 - 98 for IK 08 including one No. 4 pole connector and one No. MCB SP 'B' curved 6-32 Amp and chromium plated clamps and nut bolts, Glands complete all as per specified and directed as per manufacturer’s instructions.
55
-
-
S&F LED flood light 210 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed.
8
-
-
M&L for PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in pole foundation complete all as specified and directed.
7
-
-
S&F in repairs earth value / type indicator metal sheet post made of MS and sheet, post height 1.0 metre, sheet size 400mm x 300mm x 3mm including two coat synthetic enamel paint (yellow/red/black) and fixed on PCC (1:2:4) type B0 complete all as specified and directed.
20
-
-
M&L for 20 mm nominal bore Mild steel galvanised water tubing, medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed..
96
-
-
Labour only for taking down of cable and relaying in trenches as per existing cable of any size complete all as specified and as directed.
Note : Earthwork shall be measured and paid seprately under respective item of schedule.
1000
-
-
S&F in repairs of earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25x4mm galvanised iron strip complete all as specified and directed.
250
-
-
S&F in repairs air termination, single pointed aluminium rod 12mm dia and 300mm long complete all as specified and directed.
60
-
-
S&F in repairs porcelain, vitreous, white, brown or green insulator including washers, insulator bolts, washers and nuts etc complete all as specified and directed.
200
-
-
M&L in repairs of test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos., 8mm dia, 25mm long hexagonal head screw complete all as specified and directed.
20
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements