Military Engineer Services Tender

Material & labour for Injecting grout of epoxy mixed with ordinary Portland cement 43 grade in proportion as per instruction of the manufacturer into RCC roof by suitable gun/pump at required pressure including cutting of nipples after curing etc., complete all as specified and as directed.

Material & labour for preparing RCC roof surfaces with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particle and applying APP membrane HMHDPE 3 Kg plain (thickness 2.1 mm) (total weight of the finished membrane not less than 3.0 kg/ sqm ± 5 % per sqm) confirming to IS 16540: 2017 over a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25⁰C, 0.87-0.89 kg/ litre and viscosity 70-160 cps, laying over the primer coat using Butane Torch and sealing all joints, overlapping etc. as per Annex D of IS 16540: 2017, complete all as specified and as directed.

Material & labour for cutting grooves or chase in brick wall, 75 mm wide and 65 mm deep and including filling with cement mortar 1:4 mixed with water proofing as mentioned in Annex D of IS 16532: 2017, IS 16540: 2017 compound, complete all as specified and as directed.

Material & labour for PCC benching/ angle filleting at the junction of parapet and RCC roof in M15 (Nominal Mix) using 12.5 mm nominal size crushed stone aggregate mixed with water proofing compound as mentioned in Annex D of IS 16532: 2017, IS 16540: 2017 compound complete all as specified and as directed.

Material & labour for cement concrete M15 (Nominal Mix) using 12.5 mm nominal size graded crushed stone aggregate mixed with water proofing compound as levelling course mass concrete finished even and fair complete all as specified and as directed. Note:- Water proofing compound shall be measured and paid for separately.

Material & labour for plain cement concrete tiles, general purpose, double layer of size 25 cm X 25 cm X 22 mm thick with grey cement and no pigments in wearing layer as per IS 1237: 2012, including laying over 15mm thick bedding of cement mortar (1:3) and neat cement slurry, set, jointed and grouted in cement mortar (1:3) mixed with 2% integral water proofing compound by weight of cement in 4 mm wide joints all as specified and as directed Note :- water proofing compound shall be measured and paid for separately.

Dismantling of Asbestos cement (corrugated, semi-corrugated, etc) sheets in roof coverings including ridges etc complete all as specified and directed.

Supply & Fixing pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply & Fixing pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling cast iron work of any description etc complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position etc., complete all as specified and directed.

Supply & Fixing roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of grade Fe 410 -W (Gde- E- 250) quality-A etc., complete all as specified and directed.

Demolition of brick work built in cement mortar of any description including quoins, arches, pillars etc but excluding ashlars facing complete all as specified and directed by the Engr-in-charge.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

Material & Labour for brick work with sub class ‘B’ bricks straight or curved on plan exc. 6 mtr mean radius built in CM (1:6), complete all as specified and directed.

Material & Labour for brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4, complete all as specified and directed.

Material & Labour for PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in coping including weathering slightly rounded or chamfered angles and throating including use & waste of form work complete all as specified and directed.

Taking down plaster on brick or concrete surfaces including raking out joints for key and scrubbing down with water etc complete all as specified and directed.

Material & Labour for rendering 15 mm thick on fair faces of brick or concrete the surface even and smooth without using extra cement in CM (1:4) Mixed with water proofing compound @ 3% complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid separately)

Supply only integral water proofing compound complete all as specified and directed.

Material & Labour for rendering 15 mm thick on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement in CM (1:6) complete all as specified and directed.

Material & Labour for applying a coat of 1.5 mm thick Birla wall care putty as per manufacture instruction complete all as specified and directed.

Material & Labour for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper etc., complete all as specified and directed.

Material & Labour for complete removal of existing treatment by scrapping, wire brushing from old walls and applying two coats of oil bound distemper including preparation of surfaces etc., complete all as specified and directed.

Material & Labour for preparation of old decorated plastered surfaces of ceiling including cornices, pilasters etc and applying two coat of white wash etc., complete all as specified and directed.

Material & Labour for preparation of old painted surface of wood and wood based material of any description over 10 cm in width or girth and applying one coats of synthetic enamel paint etc., complete all as specified and directed.

Material & Labour preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer, complete all as specified and directed.

Material & Labour preparation of old steel surfaces and applying one coats of synthetic enamel paint of any description over 10 cm width and girth complete all as specified and directed.

Dismantling of wall and ceiling boards (fiber, pulp, insulation, etc.) or insulation boards/slabs/blankets, of any thickness, including snap grid frame work complete all as specified and directed.

Supply and fixing in position suspended false ceiling using GI exposed ceiling suspension system of grid size 600mm x 600mm with main runner 38x24mm (0.25mm thick) of central black line / black groove, Cross Tee 27mmx24mm(0.25mm thick) of central black line / black groove and Angle 22mm x 24mm (0.4mm thick) & including Supply and fixing 4mm thick (high pressure stream cured) pre-painted self-embossed, reinforced designer cement board (Ivory) with texture of size 595 x 595mm including conforming to IS 14862-2000 to be placed in a grid if gI system duly suspended with 4 mm dia galvanized iron /mild steel bar hanger fixed with steel dash fastener or iron purlins from the roof with adjustment clip. The main runner to be secured to structural soffit by hanger @ 1200mm maximum c/c. The last hanger at the end of each main runner should not be placed at more than 450mm from the adjacent wall. Flush fitting 1200mm cross tee to be interlocked between main runner @600mm C/C, so as to firm 600mm x 600mm grid etc., complete all as specified and directed

Providing and fixing ECO-4000 series pre-coated double rebated openable window or ventilator made out of galvanised steel colour coated/powder coated (base steel as per IS 513 of 'D' quality galvanised as per IS 277 with zinc of 120 gm/Sqm) with total thickness of coating 0.58 microns finished painted with polyster paint of 12 to 16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with polyster powder up to 50-60 microns thick outer frame section 72x55 mm, centre mullion section 72x50 mm, shutter section 47x20 mm, fly mesh section 40x20 mm and the fixed glass beading section 12x12 mm outer frame and mullions shall consist rebate for glazed shutter, fly mesh and 20 mm provision for guard bars/grills, the section cut to length miter jointed with corner brackets, center mullions fixed with mullion cap, stay handles, latch 2 Nos of heavy duty stainless steel pivot hinges per shutter and paneled with 5 mm thick pain float glass and stainless steel (304 grade) mesh for fly mesh shutter fitted with EPDM (Ethyl Propylene Diamine Monomer ) gaskets including fixing window with concrete/stone or brick masonry wall by means of self expanding sleeves and driving MS electroplated 80 mm long bolt into the sleeves through frames (Minimum 4 nos for 1600mm high windows, 3 Nos for 1200 mm less window and 2 Nos in ventilator ), including 10 mm square bars welded to 6x12 mm flat at a distance 125 mm c/c etc as per direction of Engineer-in-Charge. Note:- Refer TD No CELZ/C-TD/102 sheet 1/2 and 2/2. Make :- M/S Ashwani & Sons, E-15 patel nagar -II Gaziabad (UP),NCL Alltek & Seccolar Ltd & any other manufacturer approved by E-in-Branch

Dismantling unserviceable PVC water storage tank of 500 Ltr capacity, complete all as specified and directed.

Supply and fixing 500 ltr rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with all as specified in SSR Part I, complete all as specified and directed.

Supply & Fixing 15mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Supply & Fixing in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 210 gms) complete screwed for iron pipe or brass ferrule of size 20 mm bore, complete all as specified and directed.

Supply & Fixing PVC (SWR) pipe 75 mm dia bore, single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed.

Supply & Fixing 75mm dia PVC (SWR) bends any radius, complete all as specified and directed.

Supply & Fixing PVC (SWR) rain water pipes, 110mm bore, single socketed , in any length with rubber ring joints, fixed to walls with PVC clamps including fixing of pipes in roof projection etc., complete all as specified and directed.

Supply & Fixing PVC (SWR) bends /shoes 110 mm bore any radius, complete all as specified and directed.

Supply & Fixing PVC (SWR) junction single (single ‘T’) equal or unequal nominal bore in mm joints fixed to walls for 110mm bore, complete all as specified and directed.

Material & labour for machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Supply & Fixing 25mm dia drapery rod (Poles, finials, ring & bracket, complete all as specified and directed.

Material & labour for 75mm thick cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate finished even & smooth without using extra cement as in plinth protection including forming joint to full depth at every 3.0m interval and at every charge of direction and filled mixture of bitumen and sand (1:3) by weight, complete all as specified and directed.

Material & labour for Preparation of new plastered surfaces of wall and applying two coats of Exterior emulsion paint over a coat of primer, complete all as specified and directed.

Material & labour for complete removal of existing treatment and applying two coats of weather proof exterior paint over a coat of primer and putty where required on wall including preparation of surfaces etc., complete all as specified and directed.

NOTE :- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs 29,375.00 /- ]