Awadhesh Pratap Singh University Tender

Executive table 1350 MM Table without CPU Hanger size shall be 1350 Width mm x 750 Depth mm x 728 Height mm.Top shall be 18 mm thick Pre laminated particle board all work surface edges shall be having duly sealed with 2 mm thick PVC edgebanding. Understructure Modesty Panel 18 mm thick Pre laminated particle board . The Rectangular frame shall be fabricated component in 1.2 mm thick CRCA , Finish : powder Coat( epoxy polyster) . Leg shall be fabricated component in 38 mm x 25 mm 1.2 mm thick MS ERW ATube ,finish powder coat ( epoxy polyster).The plastic cap for cable travel shall be injection moulded polypropylene and leveler glide for shall be nylon 6 & MS bolt. The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawer front shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever and handle and leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyster) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyster) . Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Executive table 1200 MM Table without CPU Hanger size shall be 1200 Width mm x 600 Depth mm x 728 Height mm. Top shall be 18 mm thick Pre laminated particle board all work surface edges shall be having duly sealed with 2 mm thick PVC edgebanding. Understructure Modesty Panel 18 mm thick Pre laminated particle board . The Rectangular frame shall be fabricated component in 1.2 mm thick CRCA , Finish : powder Coat( epoxy polyster) . Leg shall be fabricated component in 38 mm x 25 mm 1.2 mm thick MS ERW ATube ,finish powder coat ( epoxy polyster).The plastic cap for cable travel shall be injection moulded polypropylene and leveler glide for shall be nylon 6 & MS bolt. The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawer front shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever and handle and leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyster) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyster) . Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Executive table 1650 MM Table with CPU Hanger size shall be 1650 Width x 9000 Depth x 728 Height mm . Top shall be 18 mm thick Pre laminated particle board all work surface edges shall be having duly sealed with 2 mm thick PVC edgebanding. Understructure Modesty Panel 18 mm thick Pre laminated particle board . The Rectangular frame shall be fabricated component in 1.2 mm thick CRCA , Finish : powder Coat( epoxy polyster) . Leg shall be fabricated component in 38 mm x 25 mm 1.2 mm thick MS ERW ATube ,finish powder coat ( epoxy polyster).The plastic cap for cable travel shall be injection moulded polypropylene and leveler glide for shall be nylon 6 & MS bolt. The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawer front shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever and handle and leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyster) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyster) . Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Big office table double drawer size shall be 1665 Width x 900 Depth x 750 Height . The top panels shall be made from 25 +/- 0.5 mm thick Pre - laminated boards as per with 2 mm thick PVC edge banding on all sides . Understructure shall be made from 0.9 mm +/- 0.09 mm thick powder coated 50 microns (+/-10) CRCA MS. Tubular Frame shall be sq. 25.4 +/- 0.3 mm x 1.2 +/- 0.096 mm thick MS ERW tube .Modesty panel shall be made from 1.0 +/- 0.09 mm thick powder coated 50 microns (+/- 10). The Storage shall be having shell 0.5 +/- 0.07 mm thick CRCA MS plus drawer tray 0.5 +/- 0.07 mm thick CRCA MS plus drawer front 0.8 +/- 0.1 mm thick CRCA MS . Also there should be 10 lever cam lock plus handles built in plastic.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

office table double drawer size shall be 1365 Width x 680 Depth x 735 Height . The top panels shall be made from 18 +/- 0.5 mm thick Pre - laminated boards as per with 2 mm thick PVC edge banding on all sides . Understructure shall be made from 0.9 mm +/- 0.09 mm thick powder coated 50 microns (+/-10) CRCA MS. Tubular Frame shall be dia. 25.4 +/- 0.3 mm x 1.2 +/- 0.096 mm thick MS ERW tube .Modesty panel shall be made from 1.0 +/- 0.09 mm thick powder coated 50 microns (+/- 10). The Storage shall be having shell 0.5 +/- 0.07 mm thick CRCA MS plus drawer tray 0.5 +/- 0.07 mm thick CRCA MS plus drawer front 0.8 +/- 0.1 mm thick CRCA MS . Also there should be 10 lever cam lock plus handles built in plastic. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Office table single drawer size shall be 1199 Width x 590 Depth x 735 Height . The top panels shall be made from 18 +/- 0.5 mm thick Pre - laminated boards as per with 2 mm thick PVC edge banding on all sides . Understructure shall be made from 0.9 mm +/- 0.09 mm thick powder coated 50 microns (+/-10) CRCA MS. Tubular Frame shall be dia. 25.4 +/- 0.3 mm x 1.2 +/- 0.096 mm thick MS ERW tube .Modesty panel shall be made from 1.0 +/- 0.09 mm thick powder coated 50 microns (+/- 10). The Storage shall be having shell 0.5 +/- 0.07 mm thick CRCA MS plus drawer tray 0.5 +/- 0.07 mm thick CRCA MS plus drawer front 0.8 +/- 0.1 mm thick CRCA MS . Also there should be 10 lever cam lock plus handles built in plastic.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Wooden office table 4*2size shall be 1200 Width x 600 Depth x 740 Height . The top shall be made from 25 mm thick pre- laminated board . All the edges are sealed with 2 mm thick PVC edge band all around . Side panels shall be made from 25 mm thick pre- laminated paticle board . All the edges are sealed with 2 mm thick PVC edge band on the user side and 0.8 mm on the top and bottom side .The side panels have 2 glide screws each for levelling of the desk. Modesty panel shall be made from 18 mm thick pre- laminated particle board . All the edges are sealed with 0.8 mm thick PVC edge band all around. Freestanding Pedestal shall be made from 18 mm pre- laminated particle board with a combination of 2 mm and 0.8 mm PVC edge band on all the exposed surfaces as per requirement . The drawers are provided with suitable slides for smooth operation . All the pedestal drawers are centrally locked with a single key .Drawer slides are of Hettich.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Wooden office table 5*2.5size shall be 1500 Width x 750 Depth x 740 Height . The top shall be made from 25 mm thick pre- laminated board . All the edges are sealed with 2 mm thick PVC edge band all around . Side panels shall be made from 25 mm thick pre- laminated paticle board . All the edges are sealed with 2 mm thick PVC edge band on the user side and 0.8 mm on the top and bottom side .The side panels have 2 glide screws each for levelling of the desk. Modesty panel shall be made from 18 mm thick pre- laminated particle board . All the edges are sealed with 0.8 mm thick PVC edge band all around. Freestanding Pedestal shall be made from 18 mm pre- laminated particle board with a combination of 2 mm and 0.8 mm PVC edge band on all the exposed surfaces as per requirement . The drawers are provided with suitable slides for smooth operation . All the pedestal drawers are centrally locked with a single key .Drawer slides are of Hettich.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Premium executive table with side table size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. Finesse ERU -3616 LHS size shall be 1050 Width x 450 Depth x 705 Height. The top of Finesse ERU -3616 LHS shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Premium wooden table 1200 x 600Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management. Modesty Panel:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under- structure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping..Handle is provided for ease of opening. Storage is provided with lock for security.1200x600x750. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Premium wooden table 1500Work Surface:Made of combination of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top and 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Softclosing access flap with in-build power box are provided on work surface for wire management. Modesty Panel:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Under- structure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to topPedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Wooden table 1800 mm Primary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Secondary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Softclosing access flap with in-build power box are provided on work surface for wire management. Modesty Panel:Made of 25mm thick MDF one side laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Under- structure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS 12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Confrence Table Per Seater Worksurface: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure : It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Modesty Panel : Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns) Wire Management : An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40 60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification, IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

STORAGE cabinet CARCASS Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 0.8 mm thick PVC lipping. Pilotholes provided for fixing 12U AV equipment rack. 1 Nos 12U rack fits into one unit of 112storage. 3 Nos 12U racks fit into one unit of 312 storage GLASS 5mm thk toughened, grey tinted glass with crystal edge polish finish is used as shutter.They are fitted with self closing hinges with soft close dampner for smooth operation. BACK VENT PANEL A panel made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for ventilation. The size of the panel is different for both the modules. CASTORS Castors (4nos.) are provided at the bottom to enable mobility of the unit as required for 112 unit Castors (5nos.) are provided at the bottom to enable mobility of the unit as required for 312 unit.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

POD table Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Soft closing access flap provided for access to power supply and audio cables.Work top is available in two shapes Square and Pebble (Round).Side Panel:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990 matching to the Worktop, Edge banded with matching 2 mm thick PVC lipping. Cutout with Gromet provided for routing cables in case any Audio Visual equipment is to be fixed later.Understructure:The Under-structure consists of an Inner Tube Assembly with Top for Worktop Mounting and Base plate with levellers. The Top Plate is made of 5mm thk hot rolled steel Plates (HR) (As per IS: 2062) & the bottom plate is made of 8mm thk hot rolled steel Plates (HR) (As per IS:2062). The Inner Tube Assembly is made of 25.4mmx 25.4mm x 1.2mm thk round electric resistant welded tube (ERW)(As per IS:7138) welded together using Tungsten inert gas welding. The whole structure is epoxy polyester powder coated (DFT 40-60 microns). The product has a knock-down construction. Cutout for standard Anchor Roma 6 Module is provided for electrical fittings.An additional cutout with a plate is provided for mounting Audio Visual Cables( eg HDMI,VGA-A,etc.)removable panel:The 3D removable panels are provided for ease of servicibility. It also provides easy access to internal space in case of any Audio Visual equipment is to be added later. It is made of 1.2mm CRCA MS IS:513 and EPOXY POLYESTER Powder Coated (DFT 40-60 microns).Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Conference table 8 Seater 8 Seater size shall be 2400 Width mm x 1200 Depth mm x 750 Height mm . Top shall be 32 mm thick Base material shall be 18 + 12 mm MDF board. There shall be natural veneer 0.5 mm on top surface plus 0.6 mm balancing laminate on bottom surface Chamfer edges - PU Matt painted and veneer portion of worksurface is finished in PU Matt paint . The Veil and cross member shall be 18 mm thick base material shall be 16 mm plain particle board plus post - laminated work -surface with 0.6 mm laminate on eithe side . 2 mm thick and 0.8 mm thick PVC edge banding of matching colour on outer edges of Veil 0.8 mm thick PVC edge banding of matching colour on outer edges of cross member . The legs shall be made from 1.6 mm Matt silver Anodized Aluminium extrusion . Legs assembeled together with a plastic glide holder at bottom and 5 mm thick MS powder coated sheet at top . The plastic glide holder is having provision for wire entry and glide fixing . The wire carrying is facilited through the hollow space between two leg extrusions and the wires are concealed between removable rigid PVC extrusion in the leg . Access Flap and Switch Mounting Tray shall be made of matt silver anodized aluminium extrusion and plastic moulded components . Powder coated switch mounting tray made from 0.8 mm and 1.2 mm MS sheet .Switches to be mounted on tray as per requirement and Provision for mounting a module anchor roma swtch plate on switch mounting tray.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Computer table 1200 x 600 x 750 TABLE MATERIAL - The Table Panels are made from 18 ±0.5mm thk Pre-LaminatedExterior grade PLT ( Grade I,Type-II )(IS 12823) with PVC edgebanding on all sides.Drawer bottom panels are made up of 9mm thick (±1mm)Pre-laminated Particle Board. Locking has been provided on top drawer only. CONSTRUCTION - Table has provision of CPU monitor, Drawer and Sliding KBPT.The Table has a knock-down construction.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Library table 1800 size shall be 1800 Width mm x 900 Depth mm x 740 Height mm . The top shall be 25 mm thick PLB with 2 mm thick PVC Edge Beading plus the Understructure shall be having C - Frames 1.6 mm thick MS supporting the top . The Legs shall be of dia. 38.1 x 1.6 mm thick MS ERW tube .Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Conference table12 seater Worktop:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access panels provided with soft closing hinges.Understructure:The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction.Wire management:Bottom cabinet with door is provided for flow of wires and cables. Cutout provision below Access flap at four locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg.HDMI,VGA-A,etc).Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services). Size - 3600*1500*740 mm

Office storewel shall have an overall size of 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Small Almirah shall have an overall size of 765mm(W)x440mm(D)x1270mm(H) with welded construction. It should have the shelf thickness of 0.7mm, Back thickness of 0.8mm and all other components shall be 0.9mm thick. These components are made of CRCA ‘D’grade high yield strength as per IS:513. The storwel Minor should have a Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting (3 nos.) which shall have a Uniformly Distributed Load capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Book Case 4 Door 4 Door Book Case shall have the configuration of 914mm(W)x320mm(D)x1742mm(H). The unique design provides the right rigidity to the Top hinged doors , which shall facilitate easy use. The Book Case shall be made from prime quality CRCA steel with anti rusting treatment. It shall have a Rigid Knock Down Construction. The Top Pannel, Back Pannel and Side Pannel are made from 0.7mm high yield CRCA and other components from 0.8mm CRCA. Each door shall have a 6 Lever Cam Lock with Common Key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. Scissor Mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. Each door should be provided with plastic side end caps as handle which is easy to grip. Each compartment shall have a storage shelf with a UDL capacity of max 80 Kg. The 2 Door Book Case shall have 18mm PLB Top straight edge with PVC lipping. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Glass Door Storwel Glass Door Storwel shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The glass door storwel shall have a brass handle and a 2 way locking mechanism with shooting bolt . It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Filing Cabient 4 Drawer Vertical Filing Cabinets whcih use less floor space. Size of 4 Drawer VFC shall be 1320mm(H) X 470mm(W) X 620mm(D). All the components shall be made of CRCA . It should have 1 Point Locking Mechanism and a Rigid Knock Down Construction. The Top, Side & Drawer Front thickness should be 0.7mm. The Frames, Drawer-inside cover and Side Back Side thickness should be 0.6mm. The Back, Bottom and Drawer thickness should be 0.5mm. Easy to grip Full length Recess Handle shall be integrated into Metal Drawer for easy pull out convenience. There shall be a Snap on type plastic label holder on Drawer Fronts. In addition, 28 ‘Ezee’ / ‘Visa’ files (Foolscap) from front to back of thickness 20mm per drawer can be hanged in VFC. The Centralized locking System shall be provided along with Shooting Bolt Mechanism and 10 Lever Cam Lock. The VFC should have anti-tipping arrangement which ensures that when one drawer is opened for use, it does not allow other drawers to be opened. The High Quality Precision Ball Slide shall be provided with Drawer Load capacity of max 40 kg and UDL for 75,000 cycles (BS). Plain Triangular plate pop should be riveted at the bottom corners for rigidity. Optional Accessories like Drawer Partition and Cradle for hanging A4 file folders front to back should also be available. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Slotted angle Racks Bolt Less 6.25 ft. Hight Boltless Racks:- Product specification for Boltless shelving - Depth (, mm) 500 , Width (mm) 1300, L/L Height (mm) 425 mm & 349 mm in top shelf, System Height (mm) 2500, Upright Height (mm) 2495 , Self loading capacity 142 . UDL, WITH 6.1 UPRIGHT :- Upright type - Upright G50, Profile , ‘T’ Profile, Profile Size 50 mm x 37 mm, No of bends 9 bends, Level adjustability 25 mm, Material Grade Min Ys=210 Mpa, Mfg process Roll forming, Finish Powder coated finish on Zinc coated steel, Colour Oxford Blue, 6.2 SHELF: Width 1300 mm, Depth 500 mm, Material Zinc coated, Shelf Height 32mm,No of bends 14, Mfg Process Roll formed, Fasteners NO, Mounting ‘4’ nos of clips per shelf ( no bolting), Surface finish Zinc Coated spangle free fine finish, 6.3 BRACINGS Section Flat Mid rib and end bends, Mfg process Press forming, Connectivity Hooking & Pin it, Surface finish Zinc coated, SHELF CLIP Profile section 24 x 8 x 35mm, Material GI, Mfg process Blanking & Punching, No of bend 2, Connectivity Insertion, Surface finish Galvanized, 6.5 STABILITY MEMBER : Profile section 20 x 25 x 54mm, Each Material Zinc coated Mfg process Notching & Folding, No of bends 2, Connectivity Hooking & pin it,STRUCTURAL ANALYSIS TESTING:- •The Racks / Shelves/ selves be tested for structural rigidity and safety. Design analysis and development activities are validated and approved by premier structural institutes and organization. QUALITY ASSURANCE BY THE BIDDER/ OEM:- • Robust Quality Assurance programmed is carefully overseen by our highly-qualified and dedicated in- house quality assurance team. • The high-quality raw materials be utilize and are to be sourced from world-class steel manufacturers across the world. • The powder meant for finish be tested for its chemical and physical properties for every batch. The fasteners undergo random sampling be tested for its dimensions.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Slotted angle Racks Bolt Less 7.5ft. Height Boltless Racks:- Product specification for Boltless shelving - Depth (, mm) 500 , Width (mm) 1300, L/L Height (mm) 425 mm & 349 mm in top shelf, System Height (mm) 2500, Upright Height (mm) 2495 , Self loading capacity 142 . UDL, WITH 6.1 UPRIGHT :- Upright type - Upright G50, Profile , ‘T’ Profile, Profile Size 50 mm x 37 mm, No of bends 9 bends, Level adjustability 25 mm, Material Grade Min Ys=210 Mpa, Mfg process Roll forming, Finish Powder coated finish on Zinc coated steel, Colour Oxford Blue, 6.2 SHELF: Width 1300 mm, Depth 500 mm, Material Zinc coated, Shelf Height 32mm,No of bends 14, Mfg Process Roll formed, Fasteners NO, Mounting ‘4’ nos of clips per shelf ( no bolting), Surface finish Zinc Coated spangle free fine finish, 6.3 BRACINGS Section Flat Mid rib and end bends, Mfg process Press forming, Connectivity Hooking & Pin it, Surface finish Zinc coated, SHELF CLIP Profile section 24 x 8 x 35mm, Material GI, Mfg process Blanking & Punching, No of bend 2, Connectivity Insertion, Surface finish Galvanized, 6.5 STABILITY MEMBER : Profile section 20 x 25 x 54mm, Each Material Zinc coated Mfg process Notching & Folding, No of bends 2, Connectivity Hooking & pin it,STRUCTURAL ANALYSIS TESTING:- •The Racks / Shelves/ selves be tested for structural rigidity and safety. Design analysis and development activities are validated and approved by premier structural institutes and organization. QUALITY ASSURANCE BY THE BIDDER/ OEM:- • Robust Quality Assurance programmed is carefully overseen by our highly-qualified and dedicated in- house quality assurance team. • The high-quality raw materials be utilize and are to be sourced from world-class steel manufacturers across the world. • The powder meant for finish be tested for its chemical and physical properties for every batch. The fasteners undergo random sampling be tested for its dimensions.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

SLIDING DOOR Alimrah Overall Dimensions shall be 900mm(W)x450mm(D)x711mm(H). The top shall be Metal top (1 mm add in unit height ) .The Rigid Knock Down Construction , Back , Sides and Door shall be made from 0.7 mm high yield strength CRCA ,rest in 0.8 mm CRCA . CRCA - 'D' Grade as per IS-513 . Sliding door arrangement shall have sliding door wth top hanging arrangement to prevent derailment . Each door shall be provided with 2 plastic roller having steel ball bearing for smooth movement of door & less noise . Locking shall be 5 lever cam lock for safe locking . Handle shall be plastic flush & recessed handle . Shelving shall have Height wise adjustable shelf mounting . Uniformly Distributed Load Capacity of the shelf is 40 Kg maximum . VSDU - 2 shall have 1 no. of adjustable full shelf . Accessories optional shall be cradle with pipes for hanging godrej instadex files . Leveler shall be screw type leveler with hex plastic base and overall finish shall be epoxy polyester coated to the thickness of 50 microns . For VSDU 2 - A4 size box file can be stored vertically on one shelf and clear space above second shelf is 220 mm . Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Sliding filing cabinet Overall Dimensions shall be 900mm(W)x450mm(D)x1168.5mm(H). The top shall be Metal top (1 mm add in unit height ) . The Rigid Knock Down Construction , Back , Sides and Door shall be made from 0.7 mm high yield strength CRCA ,rest in 0.8 mm CRCA . CRCA - 'D' Grade as per IS-513 . Sliding door arrangement shall have sliding door wth top hanging arrangement to prevent derailment . Each door shall be provided with 2 plastic roller having steel ball bearing for smooth movement of door & less noise . Locking shall be 5 lever cam lock for safe locking . Handle shall be plastic flush & recessed handle . Shelving shall have Height wise adjustable shelf mounting . Uniformly Distributed Load Capacity of the shelf is 40 Kg maximum . VSDU - 5 shall have 2 no. of adjustable full shelves . Accessories optional shall be cradle with pipes for hanging godrej instadex files . Leveler shall be screw type leveler with hex plastic base and overall finish shall be epoxy polyester coated to the thickness of 50 microns . For VSDU 5 - A4 size box file can be stored vertically on two shelves and clear space above third shelf is 295 mm .Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Workstation 4*2 1200 X 600 X 1200H :- 1 Seater :- Providing and placing WISH panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200including powder coated aluminium trims.Tiles: Combination of top tiles are fabric magneitc. Bottom tiles - Plain metal.INTERMEDIATE BLOCKS Intermediate blocks are given in DL +DL finsh. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. legs - metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w1 X 1500 MM w2 x 600 mm d. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services). Supplying and placing in position joining table of the following specifications. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services). TOP SUPPORTING Pedestals - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 720 mm ht 3dr = 2box+1file. CPU trolley - with castors , KBPT with mousetray - metal.

Workstation 4.6*2.6 1350 X 750 X 1200 :- 1 Seater :- Providing and placing WISH panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200including powder coated aluminium trims.Tiles: Combination of top tiles are fabric magneitc. Bottom tiles - Plain metal.INTERMEDIATE BLOCKS Intermediate blocks are given in DL +DL finsh. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. legs - metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w1 X 1500 MM w2 x 600 mm d. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services). Supplying and placing in position joining table of the following specifications. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services). TOP SUPPORTING Pedestals - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 720 mm ht 3dr = 2box+1file. CPU trolley - with castors , KBPT with mousetray - metal.

Workstation 5*2.61500 X 750 X 1200 :- 1 Seater :- Providing and placing WISH panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200including powder coated aluminium trims.Tiles: Combination of top tiles are fabric magneitc. Bottom tiles - Plain metal.INTERMEDIATE BLOCKS Intermediate blocks are given in DL +DL finsh. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. legs - metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w1 X 1500 MM w2 x 600 mm d. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services). Supplying and placing in position joining table of the following specifications. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services). TOP SUPPORTING Pedestals - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 720 mm ht 3dr = 2box+1file. CPU trolley - with castors , KBPT with mousetray - metal.

Workstation 3*2 RECTA WORKSTATIONS - 900 X 600 1 Seater :- Providing and placing WISH panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200including powder coated aluminium trims.Tiles: Combination of top tiles are fabric magneitc. Bottom tiles - Plain metal.INTERMEDIATE BLOCKS Intermediate blocks are given in DL +DL finsh. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. legs - metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w1 X 1500 MM w2 x 600 mm d. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services). Supplying and placing in position joining table of the following specifications. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Dust Bin Open perforated dustbin of size 8" X 12" (8 Inch X 12 Inch -Tolerance +/- 10 mm). Material should be SS 200 series of thickness 0.4MM sheet (Tolerance +/-0.2 mm). Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Swing Dust bin Solid dustbin of size 15" X 36" (15 Inch X 36 Inch -Tolerance +/- 10 mm) with provision of swing lid. Material should be SS 200 series of thickness 0.4MM sheet (Tolerance +/0.2 mm) Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

White Board 8' X 4'White Board of Size 8 feet X 4 feet (Tolerance +/- 50 mm) for writing purpose. Surface material should be suitable for writing by dry wipe Marker and should be made of resin coated white sheet with core material 9mm thick partical board (+- 2 mm Tolerance) and have galvanised steel sheet as backing material. Border of white board should be made of Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285- 2002 - and width of Aluminium Frame should be 16 mm thickness (+- 3 mm tolerance).Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

White Board 4' X 3'White Board of Size 4 feet X 3 feet ((Tolerance +/- 30 mm) for writing purpose. Surface material should be suitable for writing by dry wipe Marker and should be made of resin coated white sheet with core material 9mm thick partical board (+- 2 mm Tolerance) and have galvanised steel sheet as backing material. Border of white board should be made of Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285- 2002 - and width of Aluminium Frame should be 16 mm thickness (+- 3 mm tolerance).Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Green Board 8' X 4' Green Board of Size 8 feet X 4 feet ((Tolerance +/- 50 mm) for writing purpose. Surface material should be suitable for writing with non-dust chalk and should be made of resin coated green sheet with core material 9mm thick partical board (+- 2 mm Tolerance) and have galvanised steel sheet as backing material. Border of white board should be made of Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285- 2002 - and width of Aluminium Frame should be 16 mm thickness (+- 3 mm tolerance).Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Notice Board 4' X 2'Pin up Notice Board of Size 4 feet X 2 feet (Tolerance +/- 30 mm). Surface material should be woolen felt / Fabric with core material 9 mm thick soft board (+- 2 mm Tolerance) and have Laminate sheet with extra melamine surface mix colour OR Galvanised steel sheet as backing material. Border of white board should be made of Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285- 2002 - and width of Aluminium Frame should be 16 mm thickness (+- 3 mm tolerance).Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Footrest Footrest plateform should be of size 450mm X 300mm and made of Plastic -(High Impact Polystyrene) in balck colour and it's frame should be crome plated . Overall Tolerance +/- 10 mm Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

File File should be made of plastic(Polypropene 10100 with provision of hanging on metal drawer. Height - 372mm ( +- 15mm tolerance ) and Length- 495mm ( +- 15mm tolerance ) Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Premium file File should be made of 395 GSM and should have provision of hanging on metal drawer. Open Size - 365mm X 530mm and Closed size- 265mm X 365mmTolerance +-30MM Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Key Board Pull out Tray Key Board Pull out Tray is made of 0.9mm thich CRCA 'D' Grade as per IS-513 (Size- 482mm(W) X 280mm(D) X 40mm(H) -Tolerance +/- 10 mm) withn ball slide of 350mm (long) X 11.8mm (thick) X and ball slide should have single extension (stroke - 230 mm) and ball slide should made of combination of 1.2/1.5 mm thick roll-formed CRCA 'D' grade as per IS-513. KBPT should have retro fitted mouse tray (size 210mm X 210 mm) at right hand or left hand as per user requirement and mouse tray should made of 0.9mm Thick CRCA 'D' grade as per IS-513.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Notice Board 6' X 4'Pin up Notice Board of Size 6 feet X 4 feet ((Tolerance +/- 40 mm). Surface material should be woolen felt / Fabric with core material 9 mm thick soft board (+- 2 mm Tolerance) and have Laminate sheet with extra melamine surface mix colour OR Galvanised steel sheet as backing material. Border of white board should be made of Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285- 2002 - and width of Aluminium Frame should be 16 mm thickness (+- 3 mm tolerance).Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Leather Very High Back chair SEAT/BACK ASSEMBLY : The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather. Seat SIZE : 47.6 cm. (W) x49.2 cm. (D) BACK SIZE : 47.5 cm. (W) x 77 cm. (D) ARMRESTS: The armrest top should be moulded from polyurethane(PU), upholstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of03.81±0.03 cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism should be designed with the following features: 360° revolving type.Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort.Tilt tension adjustment can be operated in seating position.5-position Tilt limiter giving option of variable tilt angle to the chair.Seat/back tilting ratio of 1: 2 The mechanism housing should be made up of HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY The pedestal should be High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS:The twin wheel castors should be injection moulded in Black Polypropylene. Seat Height -44.5 to 54.5 cm. Height -114.0-131.5 cm. Width & Depth of Chair as measured from base - Width-76.1 cm and Depth-76.1 cm Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Leather high back SEAT ASSEMBLY: The seat is made up of 12mm thick MR Grade plywood, layered with pocket spring coms, super soft foam of 32 kg/m3 density and edging foam of 28 kg/m3 dormity. A 200GSM soft touch fibre fill sheet is placed over foam sub-assembly and upholstered in natural leather or leatherette. BACK ASSEMBLY: The back assembly is made up of a combination of pinewood members, 12mm thick MR Grade plywood and 2mm thick cardboard, layered with slab stock foamof 28 kg/m3 density. A 200GSM soft touch fibre fill sheet is placed over foam sub-assembly and upholstered in natural leather or leatheretteARMPAD ASSEMBLY: The amped assembly is made up of 6mm thick MR Grade plywood fixed with MS powder-coatedbrackets, Inyered with foam of 60 kg/m3 density, A 200GSM soft touch fibre fill sheet is placed over foam sub-assembly and upholstered in natural leather or leatherette.CENTER TILT WITH MULTI POSITION LOCK MECHANISM: The mechanism is designed with the following features:360 revolving type 3 position locking Till tension adjustmentPNEUMATIC HEIGHT ADJUSTMENT: The Class 4 pneumatic height adjustment has stroke of 100.3 cmPEDESTAL ASSEMBLY: The pedestal is made of high-pressure die-cast polished aluminum with a buffed outside surface and black color-coated internal surface, it is fitted with 5 castors and has a pitch-center diameter of 67.510.5 cm (77.510cm with castors). TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black polyamide.WIDTH (W) - 69.0cmDEPTH (D) - 77.8cmHEIGHT (H) - 105.0-115.0 cmSEAT HEIGHT (SH) - 49.5-59.5 cm.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Executive chair with Heardesrt SEAT/BACK ASSEMBLY: The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Backshould be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H)Seat Size : 51.0 cm. (W) x49.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgf for 25% compression.BACK SPINE: The support spine should be made up of High Pressure Die cast polished hed Aluminum.ARMRESTS : The armrest should be having two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminum structure of armrest which should be connected to Aluminum Back spine and should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner.ACTIVE BIO-SYNCHRO mechanism:The adjustable tilting mechanism should be designed with the following features:360° revolving typeFront-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfortTilt tension adjustment can be operated in seating position5 position Tilt limiter giving option of variable tilt angle to the chairSeat / back tilting ratio of 1:2The mechanism housing should be made up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron)SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 3.75±0.1 cmLUMBAR SUPPORT ASSEMBLY: The Lumbarsupport assembly should consist of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. LumbarSupport Assembly has height adjustment of 5.0±0.5cm.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm.PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injectionmoulded in black PP having 6.0± 0.1cm wheel Diameter.The neckrest assembly consshould be ts of upholstered Neckrest inner(material-PolyPropylene) with moulded Polyurethane foam and Polyster fabric.Upholstered inner should be fixed to Neckrest cover.Neckrest should be fixed to Back assembly through Neckrest spine .Neckrest assembly has height adjustment of 5.5 +/- 0.5cm and Rotation adjustment of overall 20° +/- 2°.Overall Dimensions of ChairSeat Height - min45.5 to max 55.5cm.Height - min 95.5 to max 105.5 cm.Width & Depth of Chair as measured from pedestal - Width-75.0 cm and Depth-75.0 cm Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Revolving chair 1SEAT/BACK ASSEMBLY: The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured. upholstered with knitted fabric , over moulded High Resilience Polyurethane foam HIGH BACK SIZE: 51.8 cm. (W) x 75.2 cm. (H) SEATSIZE : 49.0 cm. (W) x 48.8 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS:Theadjustable armrest is designed with the following features: • Up-Down adjustment– 8 steps (8.0±0.5 cm range) • Height adjustable armrest structure which is powder coated & fitted with an armrest top. • Fixed Armrest Top is PUmoulded over metal insert. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features360° revolving type. • Single point control. • Front-pivot for tilt with feet resting on ground ensuringmore comfort. • Tilt tension adjustment. • 4-position locking with anti-shock feature. • Seat/back tilting ratio of 1:2 .BACK HEIGHT ADJUSTABILITY: Back can be adjusted in 5 positions by manually. Stroke of height adjustable spine is 7cm. Back height adjustability is applicable for High back and Mid back chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm.PEDESTAL ASSEMBLY WITH CASTORS: Thepedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-centre dia is Ø66.1 ± 0.5 cm. (76.1 ± 1.0 cm. with castors) .TWIN WHEEL CASTORS: The twin wheel castors areinjection moulded in black Nylon..OPTION OF SLIDING SEAT MECHANISM: Seat can be slide horizontally as per user convenience. Stroke of seat slide is 5 cm. This option is available for revolving pedestal type of chair.Overall Dimensionsof Chair-Seat Height - min 45.0 to max 55.0cm.Height - min 102.0 to max 119.0 cm.Width & Depth of Chair as measured from pedestal - Width-76.1 cm and Depth-76.1 cm."Overall Dimensions of ChairSeat Height - min 45.0 to max55.0cm.Height - min 102.0 to max 119.0 cm.Width & Depth of Chair as measured from pedestal - Width-76.1 cm and Depth-76.1 cm."Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Revolving chair 2SEAT/BACK ASSEMBLY : The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,andhardness load 16 ± 2 kgf as per IS:7888 for 25% compression.The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with LeatheretteSeatSIZE : 47.0 cm. (W) x 48.0 cm. (D)HIGH BACK SIZE: 47.7 cm. (W) x 76.4 cmARMRESTS : The armrest top should be moulded from polyurethane(PU) and mounted on to a drop lift adjustable type ubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish.Thearmrestheight adjustable up to 6.5±0.5cm in 5 steps.ACTIVE BIO-SYNCHRO MECHANISM : The adjustable tilting mechanism should be designed with the following features:360' revolving type. • Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be operated in seating position. • 5-position Tilt limiter giving option of variable tilt angle to the chair. • Seat/back tilting ratio of 1: 2 • The mechanism housing should be made up of HPDC Aluminium black powder coated.SEAT DEPTH ADJUSTMENT : Seat depth adjustment should be integrated in the seat througha sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm.ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of7.42±0.5 cm for the comfortable back support to suit individual need.PNEUMATIC HT. ADJUSTMENT: The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm.PEDESTAL ASSEMBLY: The pedestal should be High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.)TWIN WHEELCASTORS: The twin wheel castors should be injection moulded in blackPP having 6.0± 0.1cm wheel Diameter.Overall Dimensions of ChairSeat Height -43.1-53.1cmHeight -112.7-130.2cm.Width & Depth of Chair as measured from base - Width-76.1 cm and Depth-76.1 cm. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Recolving chair 3SEAT ASSEMBLY: The seat is made up of 1.5 ± 0.1 cm thick hot - pressedplywood upholstered with fabric and moulded polyurethane foam.SEAT SIZE: 51.8cm (W) x 49.7cm (D)BACK ASSEMBLY: The Back is injection moulded in glass filled Nylon which isupholstered with Mesh fabric.The back consist of adjustable Lumbar support made ofinjection moulded Polypropylene having an adjustment of 5.0 ±0.1 cm.BACK SIZE: 47.9 cm(W) x 66.9 cm (H)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam ismoulded with density 45+/-2 kg/m³ and hardness 14 ± 2 kgf as per IS:7888 for 25%compression.ARMRESTS (ADJUSTABLE) :The height adjustable armrest is made of Polypropyleneand can be adjusted to 6.0±0.1cm height.It also has swivel and To and Fro adjustmentwith moulded PU armtop.ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designedwith the following features:360° revolving typeFront-pivot for tilt with feet resting on ground & continuous lumber support ensuringmore comfort.Tilt tension adjustment can be operated in seating position.5 position Tilt limiter giving option of variable tilt angle to the chair.Seat / back tilting ratio of 1:2.The mechanism housing is made up of HPDC Aluminium & black powder coated(DFT 40 to 60 micron).HEADREST: The Headrest sub-assembly is made up of injection moulded glass filledPolypropylene which is upholstered with moulded HR polyurethane foam and fabric. Ithas an adjustment of 3.0 ± 0.1cm & it is assembled over GRETA 2.0 Full back chair.The complete headrest assembly is retro fit to the main chair.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Recvolving chair 4SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressedplywood measured as per QA method described in OCP-QLTA-P14-18 and upholsteredwith fabric upholstery covers and moulded Polyurethane foam. The seat has extra thickfoam on front edge to give comfort to popliteal area.The Back is injection moulded in glass filled Polypropylene which is upholstered withMesh fabric.The back consist of adjustable lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 ±0.1 cm. The chair seat & back size are SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)*MESH BACK SIZE51.0 cm. (W) x 70.0 cm. (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 14±2 kgf as per IS:7888 for 25% compression. ARMRESTS :The adjustable armrest is designed with the following features : Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) Armrest top is mounted on Armrest structure made of glass filled Nylon Fixed Armrest Top is PU moulded over Polypropylene insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism isdesigned with the following features: 360° revolving type.3 position locking with anti shock mechanism. Tilt tension adjustment. HEADREST: The Headrest sub-assembly is made up of injection moulded glass filled Polypropylene which is upholstered with moulded HR polyurethane foam and fabric. It has an adjustment of 4.0 ± 0.1cm & it is assembled over Thrill mesh back chair.The complete headrest assembly is retro fit to the main chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with anadjustment stroke of 9.5 ± 0.3cm. PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia.(76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.WIDTH (W): 76.1 CM.DEPTH (D): 76.1 CM.HEIGHT (H): 117.5 - 127.5 CM.

SEAT HEIGHT (SH): 46.0 - 56.0 C .MManufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Revolving chair 5 SEAT/BACK ASSEMBLY: The seat is made up of 1.2 ± 01cm thk hot pressed plywood measured. The Back is made up of injection moulded glass filled nylon & upholstered using Micro mesh fabric with high tenacity yarn with 28 density foam Sandwich in lumbar area. SEAT SIZE(Larger Seat Depth) : 47.0 cm. (W) x 51.5 cm (D). BACK SIZE : 45.0 cm. (W) x 65.3 cm. (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM The HR poly methane seat foam is moulded with density 45+/-2 kg/m" and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : Theadjustable armrest is designed with the folIowing featuresUp-Down adjustment— 8 steps (8.0±0.5cm range) Height adjustable armrest structure which is Powder Coated & fitted with an armrest top. Fixed Armrest Top is PU moulded over metal insert.LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad Lumbar pad has an adjustment of 8 0 ± 0.5 cm in height.FRONT PIVOT SYYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features.360° revolving type. • Single point control.• Front-pivot for tilt with feet resting on ground ensuring more comfort• Tilt tension adjustment. • 4-position locking with anti shock feature• Seat/back tilting ratio of 1:2.PNELJMATIC HEIGMT ADJUSTMENTT: Tne pneumatic height adjustment has an adjustment Stroke of 10.0 ± 0.3 cm.PEDE STAL ASSEMBLY: The pedestal is injection moulded in black 3G% glass-filled Nylons and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 66.1 ±0.5 cm. (76.1 + 1.0 cm. with castors).TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon.NECKREST . The Neckrest assembly consist of polypropylène pad with moulded polyurethane foam & covered with polyester fabric. Neckrest is fixed to BackAssembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2 ± 0 5 cm and rotation adjustment of overall 76 ± 2 . The complète neckrest assembly is retro Ut to the main chair.SEAT SIZE: 47.0 cm. (W) x 51.5cm. (D)BACK SIZE:45.0 cm. (W) x 65.3 cm. (H) Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services). "

Visitor chair 1 SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back should be made up 1.2 ±0.1cm. thick hot pressedplywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam should be designed with contoured lumber support for comfortable seating posture.MID BACKSIZE: 48.0cm.(W) X 64.5cm.(H)SEAT SIZE: 51.0cm.(W) X 48.0cm.(D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back should be moulded with density = 45±2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression.ARMRESTS:The armrest top should be made of moulded polyurethane (P.U) and mounted on to a fixed type tubular armrest support which should be chrome plated Finish. FIXED BACKREST: The backrest consshould be ts of a fixed type mechanism i.e. no back up/down adjustment.FIXED SPINE (COFERENCE/VISITOR): The seat and backare arrested together withfixed type spine i.e no backup/down adjustment ;made of 0.8 ± 0.05cm thk HR steel ans id back power-coated (DFT 40-60 micros).TUBULAR VISITOR FRAME(VISITOR CHAIR):The tubular frame is cantilever structure & made of Dia 2.54 ± 0.03cm. X 0.2±0.016cm.thk . M.S. E.R.W. tube with a M.S. Spine mounting bracket welded to it. Back spine is fitted to the assembly. The frame finish is Nickel Chrome plated (15-20 microns).Overall Dimensions of ChairSeat Height - 47.7cm.Height - 93.0cm.Width & Depth of Chair as measured from pedestal - Width-66.5 cm and Depth-61.6 cm. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Visitor chair 2SEAT/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The stitched cover should be made from spacer fabric and leatherette. Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with spacer fabric and leatherette.Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D)BACK SIZE : 45 cm. (W) x 60.5 cm. (D)Visitor TUBULAR FRAME: The powder coated (DFT 40-60 micron) tubular frame should be cantilever type & made of 02.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube.The back connected to frame through powder coated (DFT 40-60 micron) high pressure die cast connector piece.Overall Dimensions of ChairSeat Height - 44.8cm.Height - 99.5cm.Width-60.9 cm and Depth-64.3 cm . Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Visitor chair 3SEAT/BACK ASSEMBLY: The seat and back should be made from 1.0±0.1cm. thk. hot pressed moshould be ture resistant tant.commercial plywood and upholstered with P.U. foam and fabric. BACK SIZE: 42.0cm. (W) X 26.5cm. (H) SEAT SIZE: 42.0cm. (W) X 42.0cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density =45+1-2 kg/m3 and Hardness load 16 ± 2 kgf for 25% compression. UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type mainframe made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated--( DFT 40-60 microns ). ARMREST ASSEMBLY: The armrests should be made in twin tube form using 0 1.58cm. (5/8"") x 0.16 ±0.0128cm.thk. M.S. E.R.W. tube and black powder coated ( DFT 40-60 microns). Overall Dimensions of ChairSeat Height - 46.0 cm.Height - 82.5cm.Width & Depth of Chair as measured from base - Width-54.0cm and Depth-59.5 cm." Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Visitor chair 4SEAT/BACK ASSEMBLY: The seat and back should be made from 1.0±0.1cm. thk. hot pressed moshould be ture resistant tant.commercial plywood and upholstered with P.U. foam and fabric. BACK SIZE: 42.0cm. (W) X 26.5cm. (H) SEAT SIZE: 42.0cm. (W) X 42.0cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density =45+1-2 kg/m3 and Hardness load 16 ± 2 kgf for 25% compression. UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type mainframe made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated--( DFT 40-60 microns).Overall Dimensions of ChairSeat Height - 45.0 cm.Height - 84.5cm. Width-52.5 cm and Depth-55.8 cm.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Visitor chair 5SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0..1 cm. thick hot pressed plywood and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam should be designed withcontoured lumbar support for extra comfort.BACK SIZE: 49.5cm. (W) X 45.5cm. (H).SEAT SIZE: 49.5cm. (W) X 43.0cm. (D).HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression.ARMRESTS: The one-piece armrests made of black integral skin polyurethane with 50-70 Shore Hardness and reinforced with M.S. insert. The armrests should be scratch and weather resistant tant. The armrests should be fitted to the seat with seat armrest connecting bracket made of 0.3 ±0.022cm. thk. HR steel.FIXED TYPE mechanism: The fixed type mechanism should be without back tilt.TUBULAR UNDERSTRUCTURE: The understructure should be made of Ø2.54 2.54±0.03cm.x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated (DFT 40-60 microns). Overall Dimensions of ChairSeat Height - 45.0cm.Height -84.0cm.Width & Depth of Chair as measured from pedestal - Width-55.0 cm and Depth-58.0 cm. Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Revolving chair 7SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0..1 cm. thick hot pressed plywood and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam should be designed with contoured lumbar support for extra comfort. BACK SIZE: 49.5cm. (W) X 69.5cm. (H) SEAT SIZE: 49.5cm. (W) X 43.0cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression.ARMRESTS: The one-piece armrests made of black integral skin polyurethane with 50-70 Shore Hardness and reinforced with M.S. insert. The armrests should be scratch andweather resistant . The armrests should be fitted to the seat with seat armrest connecting bracket made of 0.3 ±0.022cm. thk. HR steel.CENTRE PIVOT mechanism):The center pivot mechanism should be designed with the following features:• 360° revolving type.• 17° ±2°maximum tilt on pivot at cerntre.• Tilt tension adjustment.• Upright position locking.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.TELESCOPIC BELLOW ASSEMBLY: The bellow should be 3 piece telescopic type and injection moulded in black Polypropylene.PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel. castors. The pedestal should be 66.3 ±0.5cm.(76.3 ±1.0 cm with castors).TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Nylon.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Revolving chair 8 SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0..1 cm. thick hot pressed plywood and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam should be designed with contoured lumbar support for extra comfort.BACK SIZE: 49.5cm. (W) X 45.5cm. (H).SEAT SIZE: 49.5cm. (W) X 43.0cm. (D).HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression.ARMRESTS: The one-piece armrests made of black integral skin polyurethane with 50-70 Shore Hardness and reinforced with M.S. insert. The armrests should be scratch and weather resistant . The armrests should be fitted to the seat with seat armrest connecting bracket made of 0.3 ±0.022cm. thk. HR steel.CENTRE PIVOT mechanism:The center pivot mechanism should be designed with the following features:•360° revolving type 17° ±2°maximum tilt on pivot at cerntre.• Tilt tension adjustment. Upright position locking.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.TELESCOPIC BELLOW ASSEMBLY: The bellow should be 3 piece telescopic type and injection moulded in black Polypropylene.PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon-66and fitted with 5 nos. twin wheel. castors. The pedestal should be 66.3 ±0.5cm.(76.3 ±1.0 cm with castors).TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Nylon.Overall Dimensions of ChairSeat Height - min 43.4 to max 55.4cm.Height - min 78.4 to max 90.4cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Revolving chair 9SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressed plywood measured. upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. HIGH BACK SIZE 47.5 cm. (W) x 69.5 cm. (H) / SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO MECHANISM : The mechanism is designed with the following features: · 360° revolving type. · Upight position locking · Tilt tension adjustmen. ·Seat/back tilting ratio of1:3.TUBULAR FRAME : The powder coated ( DFT 40-60 microns ) tubular frame is cantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube.PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.TELESCOPIC BELLOW ASSEMBLY : The bellow is 3-piece telescopic type and injection moulded in black Polypropylene.PEDESTAL ASSEMBLY : The pedestal is injection moulded in black 33%glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-centre dia. (76.3 ±1.0cm with castors).TWIN WHEEL CASTORS (FOR 9U01RG/9U02RG): The twin wheel castors are injection moulded in Black Nylon.Overall Dimensions of ChairWIDTH (W): 76.3 CM. DEPTH (D): 76.3 CM.HEIGHT (H): 97.0-109.0 CM.SEAT HEIGHT (SH): 42.5-54.5 CM.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Revolving chair 10SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressed plywood measured. upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. MID BACK SIZE 47.5 cm. (W) x 58.0 cm. (H). SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. CENTERTILT SYNCHRO MECHANISM : The mechanism is designed with the following features: ·360° revolving type. · Upight position locking · Tilt tension adjustmen. ·Seat/back tilting ratio of1:3.TUBULAR FRAME : The powder coated ( DFT40-60 microns ) tubular frame is cantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube.PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.TELESCOPIC BELLOW ASSEMBLY : The bellow is 3-piece telescopic type and injection moulded in black Polypropylene.PEDESTAL ASSEMBLY : The pedestal is injection moulded in black 33%glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-centre dia. (76.3 ±1.0cm with castors).TWIN WHEEL CASTORS (FOR 9U01RG/9U02RG): The twin wheel castors are injection moulded in Black Nylon.Overall Dimensions of ChairWIDTH (W): 76.3 CM.DEPTH (D): 76.3 CM.HEIGHT (H): 85.5-97.5 CM.SEAT HEIGHT (SH): 42.5-54.5 CM.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Visitor chair 6 SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressedplywood measured upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contouredlumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort topopliteal area.MID BACK SIZE 47.5 cm. (W) x 58.0 cm. (H). SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded withdensity = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compressionARMRESTS :The one-piece armrests are injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME :The powde r coated ( DFT 40-60 microns ) tubular frame iscantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W.Tube.Overall Dimensions of ChairWIDTH (W): 61.4 CM.DEPTH (D): 64.5 CM.HEIGHT (H): 89.5 CM.SEAT HEIGHT (SH): 46.5 CM.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Computer chair SEAT/BACK ASSEMBLY: The seat and back should be made from 1.2 ±0.1 cm.. thk. hot pressed plywood method described in. and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam should be designed with contoured lumbar support for extra comfort.SEAT SIZE: 45.0cm(W) x 42.0cm.(D).BACK SIZE: 39.0cm(W) x 47.0cm.(H).SEAT /BACK COVERS: The seat and back covers should be injection moulded in black Co-polymer PolypropyleneHIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR polyurethane foam should be moulded with density = 4+/-21kg/m and hardness load 16_± 2 kgf for 25%_compression.ARMREST ASSEMBLY (FOR 7046R): The one-piece armrests should be injection moulded from black Nylon. The armrests should be fitted to the seat with armrest connecting brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT mechanism: The permanent contact mechanism should be designed with the following features• 360° revolving type.• 14° ±2°maximum-back-tilt-only.• Upright position locking.• Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cmTELESCOPIC BELLOW ASSEMBLY: The bellow should be .3 piece telescopic type and injection moulded in black Polypropylene PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal should be 62.0 ±0.5cm. pitch-centre dia. (72.0 ±1.0cm withcastors). TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Nylon.Overall Dimensions of ChairSeat Height - min 43.0 to max 54.0cm.Height - min86.1 to max 97.1cm.Width & Depth of Chair as measured from pedestal - Width-71.0 cm and Depth-71.0 cm.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Computer chair 2SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressedplywood , upholstered with fabric upholstery covers and moulded Polyurethane foam.SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D).BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should upholstered using double layer spacer mesh fabric with high tenacity yarn.BACK SIZE : 46.5 cm (W) x 60.5 cm (H).HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression.ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features:• 360° revolving type.• 17° ±2° maximum tilt on pivot at centre • Upright position locking• Tilt tension adjustment.PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm.TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene.PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 andfitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon.Overall Dimensions of ChairSeatHeight - min 43.3 to max 54.3cm.Height - min 89.5 to max 100.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Visitor chair 7 SEAT/BACK ASSEMBLY: The seat and back should be made up of1.2 ±0.1cm. thick hot pressed plywood measured and upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam should be designed with contoured lumbar support for extra comfort.MID BACK SIZE: 49.0 cm. (W) x 47.0 cm. (H)SEAT SIZE: 49.0 cm. (W) x 44.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density = 45 ±2 kg/m3/ and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS :The one-piece armrests made of black integral skin polyurethane with 50-70 Shore 'A' Hardness and reinforced with M.S. insert. The rmrests are scratch and weather resistant. The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 0.5 ± 0.05 cm. thk. HR steel.TUBULAR FRAME: The tubular frame should be cantilever type & made of ∅ 2.54 ±0.03cm x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated ( DFT 40-60 microns ). Overall Dimensions of Chair-Seat Height - 44.0cm.Height -80.5cm.Width & Depth of Chair as measured from pedestal - Width-55.0cm and Depth61.0 cm . Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

3 seater airport chair It should be made up of black powder coated rectangular M.S.ERW tube having 8.0 ± 0.03 cm x 4.0 ± 0.03 cm x 0.2 ± 0.014 cm size. It should be chrome plated made of cold rolled steelwith 0.12 ± 0.013 cm thinkness. It should be powder-coated perforated shell made from cold rolled M.S. sheet (DIN 1023 Part1 ST-12 Grade) 0.15 ± 0.013 cm thickness.The Side Bar should be made of Chrome plated solid steel 3.0 ± 0.03 cm x 1.2 ± 0.3 cm with fluting and plastic inserts. The Shell should be assembled on the Cross Beam with help of M8 Bolts (Per Seat - 8 nos. Seat to Bracket and 4nos. Bracket to Cross Beam).Overall Dimensions Seat Height - 40.0cm, Height - 77.5cm, Width & Depth of Chair as - Width-183.0cm and Depth-67.0 cm.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Revolwing Stool Overall Dimension: Overall Sizes Diagonal Leg Dia 538 mm H470 min-655max. Top plate made of SS 304 made sheet with spin section of thickness 1mm & non corrosive. It has a diameter of 305mm, seat base made of MS ring and rectangular tube. EN8 Screw having dia of 22 mm is used for height adjustment of the seat base. The round hub made of MS ERW tube having dia of 38mm and thickness 2 mm. The Hub is welded with the legs and it accommodate and cover the lead screw mechanism. The under-structure consist of 4 legs made up of MS ERW tube of diameter 25.4 mm and 1.6mm thick. The press formed pipe leg give a round & clean look. All the legs is Provided with 4 nos of Nylon-6 bush. All metal components are pre treated with zinc phosphating in 7 tank process and then powder coated with epoxy polyester powder coating . Safe working load is 135kg Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Plastic chair without arms The Seat and Back should be made up of injection moulded indoor grade PolyPropylene compound SEAT SIZE : 52.5 cm. (W) x 53.2 cm. (D) BACK SIZE : 51.6 cm. (W) x 40.5 cm. (H) The powder coated ( DFT 50±10 microns ) welded tubularframe should be made from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm MSERW tube. The shoes should be made of indoor grade PolyPropylene compound and snap fitted with tubular frame.Overall Dimensions of ChairSeat Height - 45.0 cm.Height - 84.5cm. Width-52.5 cm and Depth-55.8 cm.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Plastic chair with desklet The Seat and Back should be made up of injection moulded indoor grade PolyPropylene compound SEAT SIZE : 52.5 cm. (W) x 53.2 cm. (D) BACK SIZE : 51.6 cm. (W) x 40.5 cm. (H) The powder coated ( DFT 50±10 microns ) welded tubular frame should be made from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm MSERW tube. The shoes should be made of indoor grade PolyPropylene compound and snap fitted with tubular frame. The Armrest should be made of indoor grade PolyPropylene compound and assembled over the tubular frame. The "L" shaped desklet should be made of 1.8+-0.05cm thick prelaminated particle board with 0.2+-0.05cm thick injection moulded poly proplylene all around. Desklet should have back and front adjustment of 4.4+-0.5cm. The paper tray should be made of 0.4mm thick MS rod which is spot welded to form a mesh like structure.Overall Dimensions of Chair-Seat Height - 45.0 cm.Height - 84.5cm.Width-57.5 cm and Depth-67.8 cm."Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

King bed Primary material of the product is made up from engineered wood with average seat height of minimum 44 cm in imperial oak color finish. The space for mattress in the bed will minnimum 78inches by 72 inches and total net weight of the bed will be more then 100kgs . All the parts of bed will sealed with proper edge binding and in knockdown condition .Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Dressing table Primary material of the product is made up from engineered wood in imperial oak color finish covered or sealed with edge binding in all the parts and corner of dressing table . Product is in knockdown condition and to be fitted directly at location.Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Mattress Mattress total dimensions 1981mm *1829mm contains 2 layers in it , thickness of care layer of the mattress is 75 mm and top layer will be 25 mm thick . Matterss contains quilting foam on top as well as pu foam in core layer and fabric is knitted as well as cotton blended in it with mass of minimum 400 gm/m2 .Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Sofa set The sofa comes with a geometric design at the headrest, stitching lines are carefully crafted with precision and exact symmetry, at every geometrical line.The frame is made from pinewood, with soft foam with toal dimensions of 83.1D x 101.1W x 86.4H Centimeters . sofa set contains 1 nos. of three seater and 2 nos. of two seater and Fully Upholstered with synthetic leather in it. seat and back of the sofa is permanently attached with each other Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

center table table top is made from tempered glass and rest of the frame is made from wooden with total dimension of 1194mmX584mm . Table contains dual storage , one at upper portion & other at bottom portion . Wooden frame is made up from three layred prelaminated particle board with height of 400 mm . Manufacturing Bidders should have the following ISO Standards –ISO – 9001:2008, and a robust Quality Management System (QMS),ISO 14001:2004, The manufacturer must have ISO 18001 - the Occupational Health and Safety Management Systems, The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Air conditioner 1.5 ton 3 star 5-in-1 Convertible Split AC with inverter compressor: Variable speed compressor which adjusts power depending on heat load. Operates at a cooling capacity ranging from 40% to 110%, adjust cooling capacity at your convenience thus helps in saving energy.Capacity (1.5 Ton): Suitable for medium sized rooms (111 to 150 sq.ft), 675 CFM & Ambient Temperature: 52℃.Energy rating: 3 star, Annual energy consumption: 980.37, ISEER value: 3.95 This model is as per the new star rating standards valid till 2024 , Warranty: 1 year on product, 5 years extended warranty on PCB, 10 years extended warranty on compressor , Condenser Coil: 100% copper evaporator and condenser with Blue Fin Anti-Corrosion coating that ensures durability and heavy duty performance for uninterrupted powerful cooling , Key Features: 5-in-1 Convertible Technology with inverter compressor, i- Sense Technology, 100% copper condenser, Evaporator coils & Connecting tube, R32 refrigerent, Backlit remote, Anti-Freeze Thermostat, Silent Operation, Anti- Microbial Self Clean Technology , Special Feature: I Sense Technology: The sensor in the remote sense the temperature around you and will control the air conditioner to match the set temperature with that of your location, providing utmost comfort , R32 Refrigerant gas: Environmental friendly - no ozone depletion potential , Item Dimensions & Weight: Indoor Unit dimension IDU - 97 (L) x 23.5 (B) x 30 (H)cms, Outdoor Unit dimension ODU - 78 (L) x 32 (B) x 54.5 (H) cms & IDU Weight (11.5 Kgs) and ODU Weight (26 kgs) , Included in the box: ‎1 Indoor Unit, 1 Outdoor unit, Inter connecting cable 3.5 metres, Inter connecting copper pipe 3 metres, 1 Remote, User Manual, Warranty card , stablizer included with all electrical fittings , Outdoorstand , modular switches ,electrical wire etc. The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Air conditioner 1.5 ton 5 star 5-in-1 Convertible Split AC with inverter compressor: Variable speed compressor which adjusts power depending on heat load. Operates at a cooling capacity ranging from 40% to 110%, adjust cooling capacity at your convenience thus helps in saving energy.Capacity (1.5 Ton): Suitable for medium sized rooms (111 to 150 sq.ft), 675 CFM & Ambient Temperature: 52℃.Energy rating: 5 star, ISEER value: 3.95 This model is as per the new star rating standards valid till 2024 , Warranty: 1 year on product, 5 years extended warranty on PCB, 10 years extended warranty on compressor , Condenser Coil: 100% copper evaporator and condenser with Blue Fin Anti-Corrosion coating that ensures durability and heavy duty performance for uninterrupted powerful cooling , Key Features: 5-in-1 Convertible Technology with inverter compressor, i- Sense Technology, 100% copper condenser, Evaporator coils & Connecting tube, R32 refrigerent, Backlit remote, Anti-Freeze Thermostat, Silent Operation, Anti- Microbial Self Clean Technology , Special Feature: I Sense Technology: The sensor in the remote sense the temperature around you and will control the air conditioner to match the set temperature with that of your location, providing utmost comfort , R32 Refrigerant gas: Environmental friendly - no ozone depletion potential , Item Dimensions & Weight: Indoor Unit dimension IDU - 97 (L) x 23.5 (B) x 30 (H)cms, Outdoor Unit dimension ODU - 78 (L) x 32 (B) x 54.5 (H) cms & IDU Weight (11.5 Kgs) and ODU Weight (26 kgs) , Included in the box: ‎1 Indoor Unit, 1 Outdoor unit, Inter connecting cable 3.5 metres, Inter connecting copper pipe 3 metres, 1 Remote, User Manual, Warranty card , stablizer included with all electrical fittings , Outdoorstand , modular switches ,electrical wire etc. The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Air conditioner 2 ton 3 star 5-in-1 Convertible Split AC with inverter compressor: Variable speed compressor which adjusts power depending on heat load. Operates at a cooling capacity ranging from 40% to 110%, adjust cooling capacity at your convenience thus helps in saving energy. Capacity (2 Ton): Suitable for large sized rooms (151 sq.ft to 200 sq.ft), 710 CFM & Ambient Temperature: 52℃Energy rating: 3 star, Annual energy consumption: 1201.27, ISEER value: 3.90 This model is as per the new star rating standards valid till 2024. Warranty: 1 year on product, 5 years extended warranty on PCB, 10 years extended warranty on compressor. Condenser Coil: 100% copper evaporator and condenser with Blue Fin Anti-Corrosion coating that ensures durability and heavy duty performance for uninterrupted powerful cooling , Key Features: 5-in-1 Convertible Technology with inverter compressor, i- Sense Technology, 100% copper condenser, Evaporator coils & Connecting tube, R32 refrigerant, Backlit remote, Anti-Freeze Thermostat, Silent Operation, Anti- Microbial Self Clean Technology Special Feature: I Sense Technology: The sensor in the remote sense the temperature around you and will control the air conditioner to match the set temperature with that of your location, providing utmost comfort . R32 Refrigerant gas: Environmental friendly - no ozone depletion potential. Item Dimensions & Weight: Indoor Unit dimension IDU - 100 (L) *23 (B) x 29.5 (H)cms, Outdoor Unit dimension ODU - 85.8 (L) x 31.2 (B) x 59.2 (H) cms & IDU Weight (11 Kgs) and ODU Weight (28 kgs). Included in the box: ‎1 Indoor Unit, 1 Outdoor unit, Inter connecting cable 3.5 metres, Inter connecting copper pipe 3 metres, 1 Remote, User Manual, Warranty card. stablizer included with all electrical fittings , Outdoorstand , modular switches ,electrical wire etc. The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Sofa set 2The sofa comes with a geometric design at the headrest, stitching lines are carefully crafted with precision and exact symmetry, at every geometrical line.The frame is made from pinewood, with soft foam with toal dimensions of 85D x 88W x 132H Centimeters . sofa set contains 1 nos. of three seater and 2 nos. of two seater and Fully Upholstered with fabric in it. seat and back of the sofa is permanently attached with each other The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

75 ltr. Cooler The Powerful portable desert cooler is suitable for rooms up to 37 square meters of the area under ideal conditions with effective i-pure console , designed with the multi stage filter that fights pollution , reduces odor and allergies to provide clean air . high effeciency cooling with long lasting dura pump, high water retention capacity with honeycomb pads and cool flow dispenser for distriburing water evenly on all sides . this cooler uses only 190 watts and can easily be operated on inverter . the desert cooler for room cooling has a large 75 ltr. tank with water level indicator in it. components contais 1 unit of air cooler , 4 unit castor wheels and 4 unit legs .

115ltr cooler The Powerful portable desert cooler is suitable for rooms up to 40 square meters of the area under ideal conditions with effective i-pure console , designed with the multi stage filter that fights pollution , reduces odor and allergies to provide clean air . high effeciency cooling with long lasting dura pump, high water retention capacity with honeycomb pads and cool flow dispenser for distriburing water evenly on all sides . this cooler uses only 195 watts and can easily be operated on inverter . the desert cooler for room cooling has a large 115 ltr. tank with water level indicator in it. components contais 1 unit of air cooler , 4 unit castor wheels and 4 unit legs .

70 ltr. Cooler The Powerful portable desert cooler is suitable for rooms up to 37 square meters of the area under ideal conditions with effective i-pure console , designed with the multi stage filter that fights pollution , reduces odor and allergies to provide clean air . high effeciency cooling with long lasting dura pump, high water retention capacity with honeycomb pads and cool flow dispenser for distriburing water evenly on all sides . this cooler uses only 200 watts and can easily be operated on inverter . the desert cooler for room cooling has a large 70 ltr. tank with water level indicator in it. components contais 1 unit of air cooler , 4 unit castor wheels and 4 unit legs.

100 ltr cooler The Powerful portable desert cooler is suitable for rooms up to 45 square meters of the area under ideal conditions with effective i-pure console , designed with the multi stage filter that fights pollution , reduces odor and allergies to provide clean air . high effeciency cooling with long lasting dura pump, high water retention capacity with honeycomb pads and cool flow dispenser for distriburing water evenly on all sides . this cooler uses only 210 watts and can easily be operated on inverter . the desert cooler for room cooling has a large 100 ltr. tank with water level indicator in it. components contais 1 unit of air cooler , 4 unit castor wheels and 4 unit legs .

Lounge chair 3 seater SEAT SHELL :The seat shell should be a welded assembly of seat,back and side frame. The seat and back should be made of 0.12±0.013cm thk CR steel sheet with oblong perforations.They should be welded to sideframe of size 3.2±0.05cmx 0.5 ± 0.05 cm thk HR steel.The welded assembly should be powder coated ( DFT 40-60 microns ). The seat has a front water fall edge to provide popliteal clearance for comfortable seating. It also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. Clean and flat surfaces of seat and back aids in easy maintenance. SEAT SIZE : 47.8 cm (W) x 44.6 cm (D) BACK SIZE : 41.6 cm (W) x 23.0 cm (H). Understructure assembly consshould be ts of connecting beam and leg assembly made of M.S. E.R.W. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.The welded structure assembly should be powder coated ( DFT 40-60 microns ).The leg assembly should be fitted with shoes and levellers in Nylon. The leg structure should be designed with minimal should be a of contact close to ground providing easy access for cleaning purposes. The shoes fitted to leg assembly help in aligning the structure for back to back arrangements. Levellers take cshould be of uneven flooring.Connecting beam should be fitted with snap locking end cap.lt also aids in side-by-side understructure alignment. ARM REST ASSEMBLY: Armrest assembly consshould be ts of armrest frame and armrest pad . The armrest frame should be made up of size 3.175±0.05cm x 0.47±0.027cm thk HR steel and it should be powder coated ( DFT40-60 microns ). Armrest pad should be injection molded in Nylon and should be fitted onto the armrest frame. SIDE TABLE ASSEMBLY: It should be a welded structure assembly made of 0.12±0.013cm thk CR steel sheet with oblong perforations which should be welded to side strip of size 3.2±0.05cm x 0.5 ± 0.05 cm thk HR steel.The welded assembly should be powdercoated ( DFT 40-60 microns ) and fitted to understructure assembly. SIDE TABLE SIZE: 20.0 cm (W) X 37.2 cm (D) .The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Single bed78*36MS Hollow Rectangular/Square section with mattress size of 78inches by 36 inches with thickness of hollow section is 1.2 mm with 4 nos of legs in it with mattress panel made from ply if 12 inches. Whole bed is painted in black color with 2 layer of powder coating with thickness of 50 microns

Study table overall dimensions shall be 900*600*745 mm with metal structure at the bottomn with 12 mm thick prelaminated particle board top as well as edge of the board to be banded with 2mm thick pvc tape with the help of hot melt glue. Product shall be in knockdown condition and to be fitted directly in site . table contains 4 legs with hollow section of 1.2mm thicness and whole frame to be painted with 50 microns thick powder coating.

Study chair metal frame Chair shall be non revolving and non tilting with armrest and contains 4 legs , each legs contains PVC shoe at the bottomn. Seat/back is made from 12mm thick moulded ply with soft foam covered with fabric cloth of 80GSM

Plastic study chair Single Piece plastic moulded chair without seat/back cushion with overall dimension of 570*560*850 mm conforming to IS 3663 ( latest ) .

Auditorium chair 1 Chair seat comes with auto tip up mechanism with push back feature and seat rest assembly is made from PU foam moulded with 15mm thick plywood insert and upholstered with fabric with total seat thickness of 110 mm included with cushion. Armrest on both sides is made from integral polyurethane foam with 65mm hardness reinforced with ms insert fixed with leg frame .The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).

Auditorium chair 2Chair seat comes with auto tip up mechanism which is spring free with a gravity tip up movement with push back feature and seat rest assembly is made from 12mm thick flat plywood insert and upholstered with 3 layer foam laminated fabric with total seat thickness of 110 mm included with cushion. Armrest on both sides is made from integral polyurethane foam with 65mm hardness reinforced with ms insert fixed with leg frame .The manufacturer must have ISO 50001- Energy management systems all certificate fro TUV NORD Certifying Agencies. The manufacturer should be certified for comprehensive GREEN MANUFACTURING certification , IAQ Certificate from (SCS Global Services) Green Guard for LOW Chemical Emmison of International repute & member of BIFMA Membership and BIFMA (Level (R) 2) Certificate from (SCS Global Services).