Military Engineer Services Tender

Total amount of Sch 'A' part-II (Excavation and Earth work)

Total amount of Sch 'A' part-III (Internal Electrification)

Total amount of Sch 'A' part-IV (Internal Water Supply)

Total amount of Sch 'A' part-V (External Electric Supply)

Total amount of Sch 'A' part-VI (External Water Supply)

Total amount of Sch 'A' part-VII (Fire Fighting System)

Sch 'A' Part- VIII (MISCELLANEOUS) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Boring for cast-in-situ bored piles of 500mm dia to any depth through any type of soil/strata by DMC method using bentonite slurry including removal of bored materials to place outside MD land all as specified and as directed Note:-The rate shall include mobilisation,erection,dismantling and demobilisation of equipment for pile boring including all labours and material. Nothing extra shall be payable for mobilisation of equipment seperately.

RCC with ready mix concrete(RMC) M30 grade in cast in situ bored pile with minimum cement content 400kg/cum of any length/any sections complete all as specified and as shown on drg including non destructive integrity test on all pile as per IS 2911 part IV. Note:-(i) Reinforcement will be measured and paid separately under relevant items

RCC with ready mix concrete(RMC) M30 grade in pile cap , grade beam & tie beam complete all as specified and shown on drg. Note:-(i) Reinforcement will be measured and paid separately under relevant items

Providing TMT bars (CRS/HCRM/CRM) in reinforcement 10mm dia and over for bored piles of any length and any dia all as shown on drgs including cut to length, bend to required shape, cranking/hooking ends if necessary and binding with 0.9mm dia MS wire annealed or welding so as to secure the bar firmly in position/required shape complete all as specified and shown on drgs.

Providing TMT bars (CRS/HCRM/CRM) in reinforcement 10mm dia and over for grade beam/tie beams and pile caps of any length and any dia all as shown on drgs including cut to length, bend to required shape, cranking/hooking ends if necessary and binding with 0.9mm dia MS wire annealed or welding so as to secure the bar firmly in position/required shape complete all as specified and shown on drgs.

Providing TMT bars (CRS/HCRM/CRM) in reinforcement 5mm dia and over up to and including 16mm dia confirming to IS-1786 as in Helical/stirups for pile cut to length, bend to required shape, cranking/hooking ends if necessary and binding with 0.9mm dia MS wire annealed or welding so as to secure the bar firmly in position/required shape complete all as specified and shown on drgs.

Providing TMT bars (CRS/HCRM/CRM) in reinforcement 5mm dia and over up to and including 12mm dia as in stirups for pile caps and grade beams including cut to length, bend to required shape, cranking/hooking ends if necessary and binding with 0.9mm dia MS wire annealed or welding so as to secure the bar firmly in position/required shape complete all as specified and shown on drgs.

PCC (1:4:8) type D2 using 40mm graded stone aggregate for concrete layer below pile caps/grade beams and foundation complete all as specified and shown on drgs.

Providing testing equipment & load and testing of 500mm dia bored pile (Initial Load test) all as per IS including removing the testing equipments from site after testing is completed all as specified and directed.

Providing testing equipment & load and testing of 500mm dia pile (Routine Load test) all as per IS including removing the testing equipments from site after testing is completed all as specified and directed.

Conducting standard penetration test all as per IS-2131 at levels and locations as directed for 500mm dia cast in situ bored piles all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep or area not exceeding 10 sqm on plan in soft/loose soil including bailing out/pumping out water on account of spring/rain or any other causes using any method as required and as directed by Engr-in-Charge for pile caps/plinth beams,raft foundation etc all as specified and shown on drawings.

Returning filling in around pile cap, plinth beams, raft foundation etc using excavated soil including spreading levelling and well ramming in layers not exc 25 cm thick all as specified and directed.

Removal of surplus soil to a distance not exceeding 50m deposited whereever dircted at a level not exc 1.5 m above starting point .

PCC (1:4:8) type D2 using 40mm graded stone aggregate for concrete layer below pile caps/grade beams and foundation complete all as specified and shown on drgs.

Formwork to sides of pile caps , grade beams rough finished surface of concrete flat all as specified .

Internal Electrification:-Ceiling fan 1400mm sweep copper wound having minimum service value of 4.1m^3/min/W and min air delivery 245m^3/min , including fixing of down rod and connecting up complete with and including three core flexible PVC insulated multi stranded copper conductor cable of size 0.5 Sq mm from ceiling rose/ connector to fan complete all as specified and directed.

Exhaust fan heavy duty 300 mm sweep 230 Volts AC 50 Hz, 1400 rpm, with high efficient heavy duty motor and die cast aluminium rotor mounted on two ball bearings, aero dynamically countered blades, rigid frames with rubber mountings etc for silent operation, including factory fabricated powder coated aluminium louvers, including connecting up from ceiling rose with 3 core flexible copper cable, PVC sheathed of size 1.5 sqmm, complete all as specified and directed at site.

LED Batten light fitting with extruded aluminium housing 4 feet long, with all accessories and integrated electronic driver,20W Make:- Philips model Smart Bright Cat part No. BN021C LED20S PSU CW GR S2 or eqvt in /Wipro/ Osram/GE

LED street light fitting with pressure die cast aluminium housing and acrylic cover as diffuser, having IP 66 protection of 30 Watt complete including fixing with GI Bracket made of 43mm outer dia GI Pipe including fixing clamps etc and wiring from junction box/ceiling rose with 3 core flexible copper wire, 1.5 sqmm complete all as specified and directed. Make:-Philips model Vistaglow Cat part No. BRP046 LED30 CW MR S1 PSU GR or eqvt in /Wipro/ Osram/GE

MCB SP 06 to 32 Amps "C" Series

MCB SPN 32 Amps "C" Series

Internal Water Supply:- Angular stop cock, chromium plated, cast copper alloy, screwed down, screwed for CPVC pipe 15 mm dia bore complete all as specified and directed.

Health faucet/ Hand shower with 8 mm dia, wall hook and easy flexible tube in crome finish1.5m long with nuts. Complete of make Jaguar cat part No ALD573 and SHA571 or equivalent complete all as specified and directed..

FIRE FIGHTING SYSTEM:- Supplying, Installation, Testing and Commissioning of Electric driven main fire pump suitable for automatic operation and consisting of following: complete in all respect as required as per the technical specification. (a) Horizontal type, centrifugal, End Suction pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq.cm. at highest and farthest outlet at specified flow of 2850 LPM at 105m. head conforming to IS 1520. (b) 90KW/120HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. Includes as per standard size of PVC insulated Copper conductor cable through the medium grade PVC Pipe Standard Size. Make:- Kirloskar / Crompton Greaves / Mather & Platt

Supplying, Installation, Testing and Commissioning of Diesel engine driven Standby Pump suitable for automatic operation and consisting of following: complete in all respect as required as per the technical specification. (a) Horizontal type, centrifugal,End Suction pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq.cm. at highest and farthest outlet at specified flow of 2850 LPM at 105 m. head conforming to IS 1520. (b) 110HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete with auto starting mechanism, 12 volts/24 Volts electric starting equipment,2x12v 180AH Batteries and leads, Diesel Tank Fabricated from MS sheet of 4mm Thick (Minimum Capacity 300 Litres) with level indicator, Bypass line,MS Piping to diesel tank from engine, exhaust pipe extended upto 1 m. outside pump house duly insulated with 50 mm. thick glass wool with 1.0 mm. thick aluminium sheet cladding, residential silencer, instruments and protection as per specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration. Make for Diesel Engine :- Kirloskar / Cummins /Crompton Greaves Make for Pump:- Kirloskar/Crompton Greaves/ Mather&Platt

Supplying, Installation, Testing and Commissioning of Jockey Pump suitable for automatic operation and consisting of following: complete in all respect as required as per the technical specification. (a)Horizontal type, centrifugal, pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal and flow of 180 LPM at 110 m. head conforming to IS 1520. (b)12.5 HP Squrrel cage induction motor, TEFC, synchronous speed 2900 RPM, suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads . Including as per standard size of PVC insulated Copper conductor cable through the medium grade PVC Pipe standard size complete all as specified and directed.. Make:- Kirloskar / Crompton Greaves / Mather & Platt.

Supply,erection, testing and commissioning of Automatic Motor Control Panel for the Electric driven main Pump,Standby Diesel Engine Driven Pump & Jockey Pump, with Star Delta Starters, switch gear and contactors shall be rated for motor HP. The panel shall include necessary indicating lamps for the RYB phases, ammeters and volt meter with selector switch. etc. The panel shall have Auto/Manual Selector Switch. The panel shall be powder coated red in colour and shall have provision for foot mounting with all accessories as required complete all as specified and directed. Make:- L&T/C&S/Seemens

Supply and fix Pressure Gauge 100mm dia with ball valve of pressure of 25Kg/Sqcm , 3/8" BSP bottom entry,weather proof with stainless steel internals,siphon tube and ball valve including fittings complete all as specified and directed. Make:- H Guru/Atom/Equivalent

Providing, laying, testing & Commissioning of GI Pipes, heavy duty conforming to IS 3589( 200mm and above) and 1239( upto 150mm) including all types of joints and heavy duty drop forged/fabricated fittings like elbows, tees flanges, tapers, nuts bolts, gaskets etc. laid in trenches, fixed on the wall / ceiling with suitable clamps etc. Rates includes painting all exposed pipes with red oxide primer and two or more coats of synthetic enamel paint of required shade complete as required. Pipes laid trenches shall be provided with.anti corroosive wrapping coating as per IS10221 and the rate shall be deemed to include the same. Note:Excavation and earth work only shall be measured and paid separately. Make:- Tata / Jindal /Zenith

200mm dia

150mm dia

100mm dia

80mm dia

Supply, installation, testing and commissioning of cast iron flanged sluice valve rating PN1.6 with non rising spindle, bronze/gun metal seat ISI marked complete with nuts ,bolts washer gaskets complete all as specified and directed. Make:- Kirloskar/Leader/Upadhyay

200mm dia

150mm dia

100mm dia

Supplying, installing and commissioning C.I.flanged "Y" type Strainer 200 mm dia with SS mesh,suitable flanges, nuts, bolts, gaskets etc. complete all as specified and directed. Make:Kejriwal/Kirloskar

Fire Hydrant landing valve type A (single head ) of 63mm dia confirming to IS 5290 complete all as specified and directed. Make: Newage/Essel/CRC

63mm dia 15 mtr long Hose Pipe confirming to IS 636 complete with male and female coupling confirming to IS 903 complete all as specified and directed. Make: Newage/Essel/CRC

Supply Installation Testing and Commissioning of Weather proof Hose cabinet for keeping One hose pipe of length 15mtrs each, branch pipe, nozzle, coupling etc of MS sheet of Thickness of 2mm complete all as specified and directed. Make:- Friends/Capital Gains

Supply, installation, testing and commissioning of Air Release Valve 25mm dia with stainless steel internal and 25 mm dia Ball valve including fittings complete all as specified and directed. Make:- Newage/ITAP/RB

Construction of brick Valve Chamber of internal dimensions 900 x900 x900mm ( bottom RCC floor of the pit should be minimum 30 cms below the bottom surface of sluice valve flange to provide sufficient working space) , bottom floor of the pit be constructed in RCC (1:2:4) 20 cms thick with 20 mm stone aggregate, inner and exposed surfaces and bottom floor of the pit should be plastered in CM (1:4) 15 MM thick. The sluice valve and other fittings should be housed in center of the pit. the vertices of the pit should in right angle and champhered .The top cover of the pit will be made out of Chequered Plate Fe 410 W grade with angle iron frame made out of MS angle 50mm x50 mmx 6 mm with galvanised steel hindges two nos ,and locking arrangements, duly painted with two coats of water resistant synthetic enamelled paint over one coat of red oxide all as specified and as directed.

FIRE ALARM SYSTEM:- Supply, installation, testing and commissioning Addressable Main Fire alarm control panel complying with BS EN 54 5 Loop panel with 99 detectors & 99 modules 7 upto 200 detectors and modules per loop complete all as specified and directed. Make:- Notifier/ Morley/ Cooper

Addressable type Multi-Sensor Detector with heat and smoke combination complete all as specified and directed. Make:- Notifier/Morley/Cooper

Addressable type Manual Call Point break glass type with Alarm LED complete all as specified and directed. Make:- Notifier/ Morley/ Cooper

Laying / fixing 2 core x 1.5 sqmm FRLS Multi standered copper conducter cable (Red Colour) suitable for Fire Alarm System complete all as specified and directed. Make:- Finolex/Polycab

Supply, Installation, Testing and commissioning of Network card RS 485 complete all as specified and directed. Make: Morley/Cooper/Edward

External Water Supply:- Supply and fixing 75 mm bore CPVC Ball valves Suitable for CPVC pipe with necessary fittings ,including taking down old one complete all as specified and directed. Make:- Supreme/Astral/Zoloto

EXTERNAL ELECTRIC SUPPLY:- Supply and Laying XLPE insulated galvanised steel strip or wire armoured eletric power cable with stranded aluminium conductor 1100 V grade of size 120 sqmm 3.5 core complete all as specified and directed. Make:-Finolex/Gloster/Polycab

Supply, spreading and levelling riddled soil as earth cushioning to UG cable by using IS seive to seperate the composite/roots etc and refilling spreading in trenches as cushioning and rammed down to form a solid bed all as specified and directed at site. Note:- Punned thickness shall be measured and paid.

MCCB 200 A 35 KA 4 pole with enclosure complete all as specified and directed. Make:- L&T/ABB/Schneider