Military Engineer Services Tender

Notes for item No. 01 & 02 (Contd):- (iv) All existing earthing of the lifts shall be maintained and made fully functional by the contractor to the entire satisfaction of the Engr-in-Charge & submit Earthing report monthly to Engr-in-charge. (v) The contractor will detail one technician staff to inspect the lift regularty regarding functioning of lifts or any other issues arising in the lift. The problem noticed if any to be informed immediately to JE E/M / Engr-in-Charge. Technician should alaways carry service tools during site visit. (vi) Contractor or his rep shall come to the site of breakdown within two hours of notification of breakdown. In case the contractor or his rep shall not visit the site for attending breakdown within two hours, a penalty of Rs 600 per fault per day shall be imposed over contractor and shall be deducted from his dues. (vii) The contractor has submit report of lifts such as daily,weekly,fortnightly,monthly,quaterly,half yearly & yearly as per format given in PS/Engr-in-charge. (viii) Adequate arrangements shall be made for dewatering in lift pit as and when water accumlates in it. (ix)Carrying out once inspection of lifts as per IS by the Govt approved lift inspector with submission of test reports to Engr-in-charge. (x) Contractor will provide DO'S & DON'TS display board in side lift. (xi)The rates quoted shall be inclusive of T&P required for carrying out repairs, stationary for maintenance of record all as specified. (xIi) All the cleaning items (Dusting cloths, floor/Glass cleaner, SS steel cleaner, broom etc) shall be provided by the contractor and rates deemed to be included in the quoted rate.Contractor is expected to inspect the lift before quoting the rate and Lifts will be handed over in the same condition. No claim will be admissible thereof.

Material and labour for carryong out Load test to the following Passenger Lift in various technical buildings along with checking all the mechanical, electrical, safety, speed locks, conditional interlocks, load/strain and light sensors for complaint free operation of the lifts including testing for the operation of ARD complete and directed by the Engr in charge all as spacified and as directed by the Engr - in- Charge. Note:- (1)The rates quoted by the tenderers shall deemed to be including arrangement of loads on its own and other safety items as required during testing.(a) Passenger lift 1000 Kg capacity of make Johnson in P-4 Bldg A block

(b) All as per above item but Passenger Lift ( 680 Kg ) of make Johnson in HR Wing G + 4 Floors.

Supply and fixing of aluminium car flooring as per existing at site suitable for 680 KG/1000 KG passenger lift installed in P-4 building block -A & P-103 HR Wing building in replacement complete all as specified and directed by Engr-in-charge.

Dismantling and taking out of unservicable main steel wire rope after necessary disconnecting from counter weight pulley and car cabin and supplying and fixing new main steel wire rope of suitable dia as per existing dia (8/10/13 mm dia) including proper necessary connection with counterweight, pulley and car cabin with clamps, bolts, washers, etc. conforming to IS 14665 latest edition in Dumbwaiter/Passenger/Goods lifts complete all as specified and directed by Engineer-in-Charge. Make - USHA MARTIN or equivalent model of make specified here-in-before.

Supply & fixing sealed maintenance free batteries 18 AH,12 Volts for ARD system of 08/10 pessengers lift with proper electrical connection in replacement complete all as specified and directed by Engineer-in-charge.Make :Exide,Amaron or Equivalent it.

Supply & fixing sealed maintenance free batteries 7 AH,12 Volts for ARD system of 08/10 pessengers lift with proper electrical connection in replacement complete all as specified and directed by Engineer-in-charge.Make :Exide,Amaron or Equivalent it.

Supply & fixing of COP assembly suitable for Johnson lift with illuminated push button floor position alarm, non stop door closer , door open , cabin fan, cabin light, stop atendant out key etc in and including 7 segment display with CPI card and stainless steel face plate duly connected with existing control and electric system complete & testing including taking out unserviceable COP assembly complete all as specificed & directed by Engineer in charge.

Supply & fixing LOP assembly with illuminated push button floor position alarm, non stop door closer , door open etc in and including 7 segment display with CPI card and stainless steel face plate duly connected with existing control and electric system complete & testing including taking out unserviceable LOP assembly complete all as specificed & directed by Engineer in charge.

Supply and fixing full beam infrared sensor upto full length of car doors (2.00 mtr) suitable for passenger lift including taking out unserviceable one from its location complete all as specified and directed by the Engineer-in-Charge. Make :Weco/TL Jones/Cedes or equivalent model of make specified here-in-before.

Supply and fixing cabin fan non oscilliating type axial/cross flow, single speed 300 mm sweep, 240 volts ISI marked with grill including taking down old unserviceable cabin fan from car cabincomplete all as directed by Engineer-in-charge.Make :- EMCO / VBM / CINI / Gailekesi or equivalent model of make.

Supply and fixing in replacement of emergency alarm with battery backup as per existing make of lits including taking out unserviceable one from its location complete all as specified and directed by the Engineer-in-Charge.

Material and Labour for preparing, scraping the old painted surfaces and applying two coat of approved colour synthetic enamelled paint in machine room on all accessories including marking /stencil writing of MES number, Location, Capacity, Sl No etc with white synthetic enamelled paint complete all as specified and directed.

Supply, fixing and testing in repair door drive system as per existing make suitable for 8/13 passenger lift serving up to G+4 floors (i.e. 05 floors) along with all electrical connection complete including taking down old unserviceable door drive of make any type from its existing location complete all as specified and directed by Engr-in-charge.

Dismantling and taking out unserviceable travelling cable from hoistway & supply and fixing new travelling cable PVC insulated 12 Core flat/ round type with standared copper conductor 0.75 sq mm, conforming to relavent IS in and including thimbles, suspended type freely move with car cabin up and down movement between ground and upper floors including necessary proper connection with mid way junction and other connection required in circuit complete all as specified and as directed suitable for G+3/G+4 bldg.

Material and Labour for 600 to 2200 central Opening door track allignment,Alignment of steel lift door suitable for lifts with suitable bearings,shoe and its connected items for noise free operation of door opening & closing complete all as specified and directed by Engr-in-charge.

M&L for earthing to switch gear/MCB DB with mild steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) connected to galvanised iron earth lead strip 25 x 4 mm by means of galvanised iron nuts, bolts and washer, earth lead connected to eqpt as directed, earth plate surrounded with adequate quantity of charcoal dust mixed with common salt to a packed thickness of 15 cm all around the plate including necessary earth work, PCC chamber and reinforced PCC cover made by PCC 1:3:6 type C-1 as in pit chamber and RCC pit cover 50 mm thick precast RCC 1:2:4 type B-1 duly reinforced with 6mm dia MS bar at 150mm c/c both ways with 10 mm dia MS round bar as handle, 20 mm bore GI pipe medium grade for watering and 40 mm dia GI pipe light grade for protection of earth lead up to 3 mtr with funnel, wire mesh etc with and including testing complete all as specified and as shown in electrical plate No 3 of MES sch Part I.

M&L Earthing continuity galvanised strip 25 x 4 mm or main earthing lead fixed to wall with clamps or recess or croses or buried in ground or drawn in conduits/pipe or fixed to poles or any other indicated situation for loop earthing etc as required all as specified and directed by Engr-in-Charge.

Taking down induction Motor of capacity 10 HP from lift machine room by disconnecting electrically and mechanically, loading / inculding transporting to workshop for repair, rewinding with ISI marked copper winding wire of existing gauge /size ISI marked insulating paper, varnish, replacement of bearings two Nos. of DE and NDE etc transporting back the motor after repairs, installing on foundation, aligning the same reconnecting electrically and mechanically and testing on Full load for satisfactory functioning complete all as specified and directed by Engr-in-Charge.

S & F of limit switches of protective device to stop lift at terminal floors during over travel suitable for 10 passenger lift complete all as specified and directed by Engr-in-charge.

M & L for speed reduction Gear box suitable for elevator with phosphorous bronze worm wheel and stain less worm shaft housed in cast iron housing with suitable bearings for worm wheel and worm shaft.The gear box shall be oil cooled with glass inspection window to inspect the oil level in the gear box.The gear box shall be provided with necesaary eye bolt for handling the gear box for transportation and erection.The shaft shall be provided with necessary key to lock the flanger properly complete all as directed and as specified .Make :-Montanri

M & L for dual shaft extended brake unit working on 110 V DC supply,the brake unit shall have 2 coils with emergency release handle along with drum and arms with brake bands of 6 mm thickness complete all as speciifed and directed.Make :-Montanri

M & L for 3 phase induction motor 11 KW capacity suitable for elevator and VVVF drive working on 415 V AC supply 50 Hz frequency,4 poles,S4 Class duty 40 % flange mounting with F class insulation.The shall have double shaft extension for fixing coupling flange on one end and on the other end fix fly wheel,both the shaft end shall be provided with locking key to fix flange and fly wheel properly.shaft dia shall be provided with IP 21 protection complete all as specified and as directed.Make :Montanri

S &F of mild steel frame suitable for mounting elevator gear box along with traction sheave,motor brake unit and other components of machine unit of elevator,the frame shall be provided with anti vibration rubber pads along with all hardware required to fix the complete machine unit the frame shall be made out of suitable C channel and I beam complete all as specified and directed.Make :Montanri