Military Engineer Services Tender
To know what Andhra Pradesh government has posted about any AP etender, Bidassist helps us to get a one-stop platform where a registered bidder can have access to the details on each and every eprocurement tender. There is no need to provide the details on the AP E-procurement website i.e. https://www.apeprocurement.gov.in as BidAssist helps us find the specific etender we're looking for. BidAassist has collated each and every Eproc Andhra Pradesh Tender on its website.
Military Engineer Services - MES Tender
Electrical and Electronics
Electrical Works
Eprocure
Opening Date11 Dec 2024
Closing Date29 Jan 2025
Tender Amount₹ 3,45,86,000
Costs
EMD
₹ 4,20,860Document Cost
₹ 2,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_688069_1Tender No
85451Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
HORIZONTAL END SUCTION LONG COUPLED TYPE CHILLED WATER PUMP WITH INSULATION Supply, installation, testing and commissioning of end-suction & top-discharge, non-self-priming, single-stage, centrifugal volute type pump having cast iron casing, enclosed type dynamically balanced phosphor-bronze/SS impeller, high tensile steel shaft, carbon steel stuffing box (sealed by mechanical seal), deep groove ball bearings, TEFC squirrel cage high efficiency induction motor, star/delta starter panel, base plate, mounting channel frame, accessories and fittings, viz. mechanical seal, pressure gauges, thermometers, drains, coupling, coupling guard, vibration isolation arrangement by means of spring/rubber type mounting, elastomeric thermal insulation of suitable thickness, etc. suitable for operation on 3- Phase, 415 V ± 10%, 50 Hz AC supply. (2 W + 1 S)
-
-
-
... More
Horizontal End Suction Long Coupled type pump with insulation suitable for 450 USgpm water flow rate and 45 m head.
2
-
-
... More
FRP RECTANGULER/ROUND SHAPE INDUCED DRAUGHT COOLING TOWER Supply, installation, commissioning and testing of induced draft top discharge counterflow type FRP cooling tower (rectangular/ round bottle shape) with FRP body and base, water spray headers, cooling tower fills, fan with motor, supporting base frames, as per manufacturer's standard instructions.
-
-
-
... More
FRP Bottle shape induced draught cooling tower of 200 TR capacity.
1
-
-
... More
HORIZONTAL SPLIT CASING CONDENSER WATER PUMP FOR COOLING TOWER Supply, installation, testing and commissioning of end-suction & top-discharge, non-self-priming, single-stage, centrifugal volute type pump having cast iron casing, enclosed type dynamically balanced phosphor-bronze/SS impeller, high tensile steel shaft, carbon steel stuffing box (sealed by mechanical seal), deep groove ball bearings, TEFC squirrel cage high efficiency induction motor, star/delta starter panel, base plate, mounting channel frame, accessories and fittings, viz. mechanical seal, pressure gauges, thermometers, drains, coupling, coupling guard, vibration isolation arrangement by means of spring/rubber type mounting suitable for operation on 3- Phase, 415 V ± 10%, 50 Hz AC supply.
-
-
-
... More
Horizontal Split Casing type pump suitable for 720 USgpm water flow rate and 45 m head.
2
-
-
... More
DOUBLE SKIN AIR HANDLING UNITS WITH 43 mm THICK CFC-FREE PUF INJECTED INSULATION PANEL HAVING 10 MICRON PRE-FILTERS Supply, installation, testing and commissioning of double-skin type horizontal, floor-mounted, top/side discharge air handling units having corrosion resistant extruded aluminum hollow profile with thermal break, heavy gauge galvanized steel channel base frame, 43 mm double skin panel with pressure injected CFC & HCFC free PUF with 'k' value of 0.02 W/°C m & density 40 kg/cum, pre-coated pre-plasticized galvanized outer and inner skin 0.60mm thick, air-tight casing using gaskets and self-adhesive tapes, AMCA certified energy efficient fans with double inlet double width forward or backward curved impellers for high static pressure mounted on aluminum extruded slide rail base frame, chilled water coils with combination of 6 rows deep with anti-corrosion Aluminum fins, PVC Naylon hinges & handles, view port and marine lamp, limit switch, SS-304 drain pan, 10 micron pre-filters, inspection windows/doors, mixing box and supply/return/fresh air dampers. [a] Suitable DIDW fan with AMCA certified blower having outlet velocity not exceeding 9.2 m/s [b] 4 Pole, TEFC, high efficiency, squirrel cage induction motor drive having BHP rating 20% higher than the peak capacity, suitable for 415 V ±10%, 50 Hz, 3-Phase AC power supply [c] V-belt drive assembly with pulleys, belt, guard, etc., double canvass connections with zip to discharge duct/plenum, etc.
[d] 50 mm thick, washable HDPE, 90% down 10 micron pre-filters, filters, fixing framework, hinge type access doors, etc. [e] 6 row deep chilled water coil section with copper fins and copper tube tested on 21 kg/sq cm with SS sandwiched drain tray, etc. [f] 18 gauge MS CRCA duly powder coated AHU sub panel board in compartamentalised construction with incomer and outgoing feeders for AHU motor, 3-way valve actuator motor, fire damper actuator motor, etc. complete with required variable frequency drive, relays, timers, contactors, PT, push buttons, switches, internal wiring, etc.
-
-
-
... More
36000 CFM; 90 TR; 75 mm WG static pressure.
2
-
-
... More
STAINLESS STEEL CHILLED WATER MAKE-UP EXPANSION TANK S & F SS- 304 closed expansion tank of pressure rating to suit the system pressure and sized adequately to compensate for water expansion due to operating temperature variations, conforming to IS: 2825- 1969 for 'non-fired pressure vessels' complete with inter-connection piping, non-return valve, safety relief valve and pressure gauge, insulated with 50 mm thick insulation and cladded with 26 G aluminium.
-
-
-
... More
SS- 304 closed expansion tank of 1000 liter capacity
2
-
-
... More
HDPE CONDENSER WATER EXPANSION TANK FOR COOLING TOWER
S & F HDPE expansion tank of pressure rating to suit the system pressure and sized adequately to compensate for water expansion due to operating temperature variations, conforming to IS: 2825- 1969 for 'non-fired pressure vessels' with interchangeable EPDM-BUTYL rubber membrane complete with inter-connection piping, non-return valve, safety relief valve and pressure gauge etc.
-
-
-
... More
HDPE expansion tank of 5000 liter capacity
1
-
-
... More
CONDENSER WATER PIPING
MS ERW CLASS- C PIPE
Supply, installation, testing and commissioning of MS ERW Class 'C' condenser water piping with all necessary fittings i.e. bends, tees, reducers, flanges, structural support, wooden blocks, air-purge valves, drain-valves, etc. as specified and as directed.
-
-
-
... More
150mm NB
80
-
-
... More
100mm NB
50
-
-
... More
BUTTERFLY VALVE
Supply, installation, testing and commissioning of PN 1.6 rated double flanged short & long body type butterfly valve designed, manufactured and tested as per IS: 13095 (1991), suitable for isolation and throttling services, having CI body & disc, SS AISI 304 disc seal, CS clamping ring and SS AISI 410 shaft and flange drilling standard end connection with accessories as specified and as directed.
-
-
-
... More
150 mm NB
20
-
-
... More
100mm NB
20
-
-
... More
NON-RETURN VALVE (NRV)
Supply, installation, testing and commissioning of PN 1.6 rated swing check type multidoor reflux valve (NRV), designed & tested as per IS: 5312-2 (1986), suitable to handle clear water having turbidity up to 5000 ppm, having CI body, door and diaphram, leaded tin bronze seat rings and flange drilling standard end connection, etc. with accessories as specified and as directed.
-
-
-
... More
100 mm NB
4
-
-
... More
Y STRAINER
Supply, installation, testing & commissioning of Y-type strainer with CI/MS body, bolted cover, flanged ends, basket of brass/ bronze/ SS wire mesh complete with flanges, nuts-bolts, gaskets and flange drilling standard end connection, etc. with accessories as specified.
-
-
-
... More
100 mm NB
2
-
-
... More
150 mm NB
4
-
-
... More
MANUAL BALANCING VALVE
Supply, installation, testing and commissioning of 2-way, globe type, PN 1.6 rated, balanced/high rangeability control valve as per following specification.
Nominal Pressure: PN16
Temperature: -10° C to +110° C
Body Material: IS:210, FG 220 CI
Stem Material: ASTM A276,GR SS 410
Disc Material: Stainless steel Disc
Hand Wheel: Cast Iron
Leakage Rate: No visible leakage
Medium Type: Water
Flange Standard: ISO7005-1 (GB/T 9113)
Shell Test Pressure: 24bar
Seal Test pressure: 17bar
-
-
-
... More
150 mm NB
3
-
-
... More
FLOW SWITCH
Supply, installation, testing and commissioning of paddle type water flow switch, having operating pressure 1000 kPa, withstand pressure 91750 kPa, insulation resistance over 100 Ω, withstand voltage 1500 V AC for 1 minute, contact point life of 1000 k cycles and bellows life 500 k cycles complete with control wiring and accessories, etc. as specified
-
-
-
... More
Water Flow Switch 80mm
6
-
-
... More
Water Flow Switch 100mm
3
-
-
... More
Water Flow Switch 150mm
3
-
-
... More
DRAIN PIPE
M & L for UPVC pipes (SCH-80) fittings, resistant to chemical & electromechanical corrosion, conforming to EN 1452-2, having specific gravity 1.43, shore hardness 70°C to 90° C, tensile strength 500 kg/sq.cm, bending strength 950 kg/sq.cm, modulus of elasticity 3.2 X 10 kg/sq.cm and dielectric strength 40 kV/mm complete with accessories as specified
-
-
-
... More
50mm dia
100
-
-
... More
CHILLED WATER PIPING
MS ERW CLASS- C PIPE WITH INSULATION
Supply, installation, testing and commissioning of MS ERW Class 'C' chilled water piping with all necessary fittings i.e. bends, tees, reducers, flanges, structural support, wooden blocks, air-purge valves, drain-valves, etc. thermally insulated with elastomeric insulation of 25 mm thick with rapped water prof fabric cloth as specified and as directed.
-
-
-
... More
100 mm NB
135
-
-
... More
80 mm NB
80
-
-
... More
65 mm NB
60
-
-
... More
BUTTERFLY VALVE WITH INSULATION
Supply, installation, testing and commissioning of PN 1.6 rated double flanged short & long body type butterfly valve designed, manufactured and tested as per IS: 13095 (1991), suitable for isolation and throttling services, having CI body & disc, SS AISI 304 disc seal, CS clamping ring and SS AISI 410 shaft and flange drilling standard end connection with elastomeric thermal insulation of suitable thickness and accessories as specified and as directed.
-
-
-
... More
100 mm NB
8
-
-
... More
80 mm NB
16
-
-
... More
65 mm NB
4
-
-
... More
NON-RETURN VALVE (NRV) WITH INSULATION
Supply, installation, testing and commissioning of PN 1.6 rated swing check type multidoor reflux valve (NRV), designed & tested as per IS: 5312-2 (1986), suitable to handle clear water having turbidity up to 5000 ppm, having CI body, door and diaphram, leaded tin bronze seat rings and flange drilling standard end connection, etc. with elastomeric thermal insulation of suitable thickness and accessories as specified and as directed.
-
-
-
... More
80 mm NB
4
-
-
... More
Y STRAINER WITH INSULATION
Supply, installation, testing & commissioning of Y-type strainer with CI/MS body, bolted cover, flanged ends, basket of brass/ bronze/ SS wire mesh complete with flanges, nuts-bolts, gaskets and flange drilling standard end connection with elastomeric thermal insulation of suitable thickness and accessories as specified and as directed.
-
-
-
... More
100 mm NB
4
-
-
... More
MANUAL BALANCING VALVE WITH INSULATION
Supply, installation, testing and commissioning of 2-way, globe type, PN 1.6 rated, balanced/high rangeability control valve as per following specification.
Nominal Pressure: PN16
Temperature: -10° C to +110° C
Body Material: IS:210, FG 220 CI
Stem Material: ASTM A276,GR SS 410
Disc Material: Stainless steel Disc
Hand Wheel: Cast Iron
Leakage Rate: No visible leakage
Medium Type: Water
Flange Standard: ISO7005-1 (GB/T 9113)
Shell Test Pressure: 24bar
Seal Test pressure: 17bar
-
-
-
... More
80 mm NB
6
-
-
... More
100 mm NB
3
-
-
... More
3-WAY TEMPERATURE CONTROL VALVE WITH INSULATION
Supply, installation, testing and commissioning of CI 3-way mixing valve, suitable for operation up-to 10 bar, with electronically operated actuator for AHUs. Water flow through the valve shall be regulated by rotation of brass slipper between the main and the bypass ports; it shall be possible to manually rotate the brass slipper through 360° and interchange the main and the common ports, to facilitate installation at site. All internals of the valve shall be rust-proof and the 'O' ring shall be of elastomeric insulation. The valve actuator shall be of electronic type with DC motor, the actuator's angle of rotation shall be 90°, it shall be without any limit switches and shall be overload-proof. It shall have an indicator to indicate the position and push-button to disengage the gear train for manual operation. All complete complete with elastomeric thermal insulation of suitable thickness as specified.
-
-
-
... More
100 mm NB
2
-
-
... More
BALL VALVE
-
-
-
... More
20 mm NB
40
-
-
... More
AUTO-AIR-VENT
Supply, installation, testing and commissioning of automatic air-vent valve with Brass OT 58 body and cover, polyacetal lever, high density expanded polyethylene float, EPDM rubber plug, stainless steel spring, polyamide capm etc. suitable for maximum operating pressure of 16 bar and maximum operating temperature 115° C respectively, installed on all high points in the water piping system to automatically remove the trapped air, installed on all high points in the water piping system to automatically remove the trapped air, all complete as specified.
-
-
-
... More
Automatic air-vent having 19 mm end connections
8
-
-
... More
TEMPERATURE GAUGE
Supply, installation, testing and commissioning of glycerin filled bimetallic thermometer in compliance to EN 13190, having standard range 0° C to 60° C up to 400° C, IP 67 protection, bimetal coil sensing element, accuracy class 1 as per EN 13190, stainless steel casing, direct bottom mounted, SS- 304 case and bayonet type bezel, SS- 316 stem and connection, aluminum dial (white background with black marking) & pointer (black colour micrometer with zero adjustable), toughened glass window, neoprene filling plug and gasket complete with accessories, etc. as specified.
-
-
-
... More
Temperature gauge of 150 mm dial size for temperature range 0° C to 100° C
28
-
-
... More
PRESSURE GAUGE
Supply, installation, testing and commissioning of glycerin filled pressure gauge in compliance to EN837-1, having standard range 15 to 0 psi and 16 psi to 10000 psi, IP 67 protection, accuracy class ±1.6% of FS, stainless steel casing and TIG argon welded socket to case, direct bottom mounted, SS- 304 case and bayonet type bezel, SS- 316 bourdon, socket, SS dial (white background with black marking) & pointer (black colour micrometer with zero adjustable), polycarbonate glass window, neoprene blow off disc and filling plug, silicon gasket complete with accessories, etc. as specified and as directed.
-
-
-
... More
Pressure gauge of 100 mm dial size for pressure range 0 psi to 200 psi
36
-
-
... More
AIR DISTRIBUTION GALVANIZED STEEL SHEET DUCTING
Supply, installation, testing and commissioning of pre-fabricated galvanized steel sheet (G.S.S.) square/rectangular ducting for supply/return air, fabricated from galvanized steel sheet, having zinc coating of 160 gm/sq m total on both sides complete with gaskets, elbows, splitters, vanes, supports etc. as per IS: 655/1963 with required scaffolding work to install the ducts at site
-
-
-
... More
24 G (MS angle flanges)
275
-
-
... More
22 G (MS angle flanges)
210
-
-
... More
20 G (MS angle flanges)
180
-
-
... More
FIRE DAMPER Supply, installation, testing and commissioning of fire damper complete with smoke detector/thermister, fusible link etc. and actuator as required for operation. The fire dampers shall be spring activated on melting of fusible link having melting point 67.13° C. The fire damper shall be located in the SA/RA ducts, at all fire rated crossoevers (shafts, walls, etc.). The control panel shall be located in such a way that the reset can easily be done. These combination smoke and fire dampers shall be interlocked with the building management system for the fire detection or HVAC and shall trip/close in the event of fire/smoke in the respective zone. Fire damper shall be tested as per ULL- 555 and certified by CBRI. The fire-damper shall be of at least 120 minutes fire-rating as per the approved particular technical specifications and shall meet the following design criteria:
[a] Bare fire dampers with 400 mm sleeve, [b] Control panel actuator, including electrical spring type actuator, remote indication of the fire damper position. [c] Interconnection wire for the fire detection & alarm system with the AHU and the smoke dampers [d] Sealing any openings around the sleeve of the fire dampers with approved fire sealant as per the recommandations of the manufacturer and specifications as specified and as directed.
.
-
-
-
... More
Motorized, spring return type, combination fire and smoke damper
2
-
-
... More
Control panel actuator, including electrical spring type actuator, remote indication of the fire damper position.
10
-
-
... More
ACOUSTIC INSULATION M&L for duct insulation with resin bonded fibre glass wool roll of density 24 kg/Cum, with factory laminated aluminium vapour barrier, thickness of insulation as specified and including the following:-
(a) M&L for cleaning the duct surface (to be insulated ) by scrapping carefully with wire brush etc. to make the surface completely free of millscale, dirt, dust, grease and other foreign materials, taking special care so that all duct joints are sealed against any leakage. (b) M&L for applying rubber based adhesive CPRX compound. (c) M&L for sealing of all longitudinal joints and circular overlaps with and including Aluminium foil tape 50 mm wide, to make the insulation leakproof. (d) M & L for securing the insulation with and including mechanically fastened nylon/' steel straps of size 12 mm/50 mm at maximum intervals of 1.2 mtr.
-
-
-
... More
50 mm thick
285
-
-
... More
THERMAL INSULATION M & L for underdeck insulation for metal roof with bonded fibre glass wool of density 24 Kg/Cum, 50 mm thick, suitably factory laminated with aluminium foil backed up by scrim and kraft paper (FSK), facing with 50 mm projection for overlap and butting comprising of the following:- (insulating material shall conform to BS - 476, Part 4,5, 6 & 7):-“(a) Supply and fix 6 mm dia M S rods between purlins suitably for supporting the required thickness of insulation material beneath the metal roof.“(b) Supply and fix 22 SWG GI wires supports for insulation.“(c) Supply and fix chicken wire mesh 12.5 mm x 22 SWG of hexagonal construction below the insulation for supporting the same."All complete as specified.
335
-
-
... More
SA/RA DIFFUSERS/ GRILLES/LOUVERS Supply, installation, testing & commissioning of removable supply/return air diffusers/grilles of extruded aluminum sections duly powder coated with volume control damper.
-
-
-
... More
4-way SA/RA diffusers/grilles/louvers with volume control damper
100
-
-
... More
Supply, fabricated, install test and commissioning Motor control panel weather proof, dust/vermin proof made out of 3.15 mm thick CRCA sheet double opeanable door with angle iron frame and locking arrangement, including bus bar suitable for 3 phase 4 wire system , 415 V 50 Hz, AC Supply with bus bar aluminium of rating 1200 Amps capacity including with PVC heat shrinkable sleeves RYB colours for phases identification, conforming to IP-62, and fixed on raised PCC platform with PCC 1:2:4 type B1 (20 mm graded aggregated) raised base with control wiring and compressing cable steel gland brass, Aluminium lugs of suitable size etc, and compressing the follwing items conforming to CPRI approved manufacturer:-
1
-
-
... More
(a) ACB 4 Pole 800 amps 415 V with mannual drawout type and thermal megnetc realese Amps, 50KA - 01 No (for incoming)
(b) MCCB TP 350 amps 415 V , 36 KA - 03 No (For Compressor)
(c) MCCB TP 250 Amps 415 V , 36 KA -02 No (For AHU)
(d) MCCB 3 Pole 63 Amps 415 V , 10 KA -01 No (For Plant Room).
(e) Star delta starter for 25 HP condensor pump-02 Nos.
(f) Star delta starter for 20 HP Chilled water pump- 02 Nos.
(g) Star delta starter for 7.5 HP CT Fan. .
(h) CT secondary site selectable 1A/5A.
(j) Danger notice plate
(k) CT/PT one step higher of rating current Site programmable.
(l) Constant Wh vewing in LCD multifunction meters in auto scroll mode.
(m) LCD multifunction meters site selectavle for Kwh + 2 Parameters.
(n) Dedicated buttons available for direct access to basic, power and energy parameters.
(o) Phase indicator lamps with fuse carriers -06 Set of three
(p) Volmeter and ammeter.
-
-
-
... More
POWER CABLES
M & L for IS 694 marked, FIA/TAC approved stranded aluminium/copper conductor (as per IS 8130), XLPE insulated, extruded PVC type ST-2 (as per IS: 5831) sheathed, single layer of galvanized steel flat strip armoured cable of 1.1 kV grade, conforming to IS 7098 (Part-2), including cable termination and cable glanding.
-
-
-
... More
Aluminum Conductor, 120 sq mm, 3.5 core
40
-
-
... More
Aluminum Conductor, 95 sq mm, 3.5 core
85
-
-
... More
Aluminum Conductor, 35 sq mm, 3.5 core
95
-
-
... More
Aluminum Conductor, 25 sq mm, 3.5 core
120
-
-
... More
EARTHING
M & L for earthing complate with copper earth plate electrode of 60 cm X 60 cm X 3.15 mm thick size , buried directly in ground (earth pit not less than 2.25 m deep below ground level ) with top edge of the plate not less than 1.5 m below normal ground level, connected to 20 mm X 3 mm copper strip as earthing lead,by means of bolts , nuts, check nuts and washer of galvanised iron or steel ,connected to earthing test point, including testing on completion.
24
-
-
... More
M & L for earth contuinity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 20 mm X 3 mm copper strip
155
-
-
... More
Dismantling of central type AC plant any type of capacitys upto 3x 50 TR water cooled AC Plant and 3 x 50 TR comprising of following complete and loading transporting and handing over to the MES store yard and as directed by Engr-in -charge.
Note :- i) Chiller units AC plant compressor,mounting frame with refrigeration piping and instrument panel complete. ii) condenser piping /Chiller piping with fitting fixture etc. iii) Ducting with grills and diffusers,dampers,supports. iv) Air handling unit complete v) cooling tower and connected accesories complete. vi) LT electrical panel board and cable.
1
-
-
... More
WATER-COOLED SCROLLTYPE CHILLER UNIT WITH R22/R407C/R40a REFRIGERANT Supply, install, commissioning and testing of Air-cooled Scroll chiller, with multi- compressors, comprising of semi - hermetic/hermetic/open type compressors, DX Evaporator, shell and tube condenser, suitable expansion device, suitable for operation on R - 22 /R - 407 C/R 410a refrigerants and of following nominal capacity. (2 Working + 1 Stand by)
-
-
-
... More
scroll type chiller of nominal capacity not less than 01x 50 TR, suitable for ambient conditions, with AHRI(Air Conditioning, heating and Refrigeration Institute) certification.
3
-
-
... More
HORIZONTAL END SUCTION LONG COUPLED TYPE CHILLED WATER PUMP WITH INSULATION Supply, installation, testing and commissioning of end-suction & top-discharge, non-self-priming, single-stage, centrifugal volute type pump having cast iron casing, enclosed type dynamically balanced phosphor-bronze/SS impeller, high tensile steel shaft, carbon steel stuffing box (sealed by mechanical seal), deep groove ball bearings, TEFC squirrel cage high efficiency induction motor, star/delta starter panel, base plate, mounting channel frame, accessories and fittings, viz. mechanical seal, pressure gauges, thermometers, drains, coupling, coupling guard, vibration isolation arrangement by means of spring/rubber type mounting, elastomeric thermal insulation of suitable thickness, etc. suitable for operation on 3- Phase, 415 V ± 10%, 50 Hz AC supply. (1 Working + 1 Stand by)
-
-
-
... More
Horizontal End Suction Long Coupled type pump with insulation suitable for 240 USgpm water flow rate and 45 m head
2
-
-
... More
FRP RECTANGULER/ROUND SHAPE INDUCED DRAUGHT COOLING TOWER Supply, installation, commissioning and testing of induced draft top discharge counterflow type FRP cooling tower (rectangular/round bottle shape) with FRP body and base, water spray headers, cooling tower fills, fan with motor, supporting base frames, as per manufacturer's standard instructions.
-
-
-
... More
FRP Bottle shape induced draught cooling tower of 110 TR capacity
1
-
-
... More
HORIZONTAL SPLIT CASING CONDENSER WATER PUMP FOR COOLING TOWER Supply, installation, testing and commissioning of end-suction & top-discharge, non-self-priming, single-stage, centrifugal volute type pump having cast iron casing, enclosed type dynamically balanced phosphor-bronze/SS impeller, high tensile steel shaft, carbon steel stuffing box (sealed by mechanical seal), deep groove ball bearings, TEFC squirrel cage high efficiency induction motor, star/delta starter panel, base plate, mounting channel frame, accessories and fittings, viz. mechanical seal, pressure gauges, thermometers, drains, coupling, coupling guard, vibration isolation arrangement by means of spring/rubber type mounting suitable for operation on 3- Phase, 415 V ± 10%, 50 Hz AC supply.
-
-
-
... More
Horizontal Split Casing type pump suitable for 400 USgpm water flow rate and 45 m head
2
-
-
... More
DOUBLE SKIN AIR HANDLING UNITS WITH 43 mm THICK CFC-FREE PUF INJECTED INSULATION PANEL HAVING 10 MICRON PRE-FILTERS Supply, installation, testing and commissioning of double-skin type horizontal, floor-mounted, top/side discharge air handling units having corrosion resistant extruded aluminum hollow profile with thermal break, heavy gauge galvanized steel channel base frame, 43 mm double skin panel with pressure injected CFC & HCFC free PUF with 'k' value of 0.02 W/°C m & density 40 kg/cum, pre-coated pre-plasticized galvanized outer and inner skin 0.60mm thick, air-tight casing using gaskets and self-adhesive tapes, AMCA certified energy efficient fans with double inlet double width forward or backward curved impellers for high static pressure mounted on aluminum extruded slide rail base frame, chilled water coils with combination of 6 rows deep with anti-corrosion Aluminum fins, PVC Naylon hinges & handles, view port and marine lamp, limit switch, SS-304 drain pan, 10 micron pre-filters, inspection windows/doors, mixing box and supply/return/fresh air dampers. [a] Suitable DIDW fan with AMCA certified blower having outlet velocity not exceeding 9.2 m/s [b] 4 Pole, TEFC, high efficiency, squirrel cage induction motor drive having BHP rating 20% higher than the peak capacity, suitable for 415 V ±10%, 50 Hz, 3-Phase AC power supply [c] V-belt drive assembly with pulleys, belt, guard, etc., double canvass connections with zip to discharge duct/plenum, etc. [d] 50 mm thick, washable HDPE, 90% down 10 micron pre-filters, filters, fixing framework, hinge type access doors, etc. [e] 6 row deep chilled water coil section with copper fins and copper tube tested on 21 kg/sq cm with SS sandwiched drain tray, etc. [f] 18 gauge MS CRCA duly powder coated AHU sub panel board in compartamentalised construction with incomer and outgoing feeders for AHU motor, 3-way valve actuator motor, fire damper actuator motor, etc. complete with required variable frequency drive, relays, timers, contactors, PT, push buttons, switches, internal wiring, etc.
-
-
-
... More
20000 CFM; 50 TR; 75 mm WG static pressure.
2
-
-
... More
HDPE CONDENSER WATER EXPANSION TANK FOR COOLING TOWER S & F PVC expansion tank of pressure rating to suit the system pressure and sized adequately to compensate for water expansion due to operating temperature variations, conforming to IS: 2825- 1969 for 'non-fired pressure vessels' with interchangeable EPDM-BUTYL rubber membrane complete with inter-connection piping, non-return valve, safety relief valve and pressure gauge etc.
-
-
-
... More
PVC expansion tank of 2000 liter capacity
1
-
-
... More
Supply, fabricate, install, test and commissioning motor control panel weather proof dust/vermin proof, made out of 3.15 mm thick CRCA sheet double openable door with angle iron frame and locking arrangement, including bus bar suitable for 3 phase 4 wire system, 415 V, 50 Hz AC Supply with bus bar aluminium 600 Amps capacity including with PVC sleeves/taps RYB colours for phases identification, conforming to IP-54, and fixed on raised PCC platform with PCC 1:2:4 type B-1 (20 mm graded aggregate) raised base with control wiring and compressing cable gland brass, alminium lugs etc and compressing the following items:-
(a) MCCB 4 Pole, 400 Amps, 36 KA - 01 (for incoming ).
(b) MCCB 4 Pole 125 Amps, 25 KA - 03 (Outgoing to Chiller pump 2w+1stand by).
(c) MCCB 4 pole 63 Amps 25 ka -02Nos ( for AHU) (d) Star delta starter for 5 HP CT Fan -01 No.
(e) Star delta starterr for 7.5 HP Chiller water pump - 02 Nos.
(f) Star delta starter for 10 HP Condenser pump - 02 Nos.
(g) Star delta starter for 12.5 HP AHU -02 Nos.
(h) CT secondary site selectable 1A/5A.
(j) Danger notice plate
(k) CT/PT one step higher of rating current Site programmable.
(l) 128 Sample/cycle
(m) Constant Wh vewing in LCD multifunction meters in auto scroll mode.
(n) LCD multifunction meters site selectavle for Kwh + 2 Parameters.
(o) Dedicated buttons available for direct access to basic, power and energy parameters.
(p) Phase indicator lamps with fuse carriers -06 Set of three
1
-
-
... More
EARTH WORK
-
-
-
... More
Excavation in trenches/foundation in soft/loose soil not exceeding 1.5 m wide and not exceeding 1.50 m deep for laying of cables, Earthing etc. and getting out complete all as specified.
0.74
-
-
... More
Excavation in trenches/foundation in soft/loose soil not exceeding 1.5 m wide and exceeding 1.50 m deep and not exceeding 3.0 m for laying of cables, Earthing etc. and getting out complete all as specified.
0.37
-
-
... More
S & F Cast iron work grade FG 150, Articles exc 5 kg each unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles as specified.
6.57
-
-
... More
M & L for Setting in cement mortar 1:3 and flaunching with cement concrete 1:2:4 type B-1 cast iron manhole covers and frames, medium duty, any type and size fixing as specified.
1
-
-
... More
Removing excavated material in soft/loose soil exc. 1.50 km but n exc. 5 km and depositing where directed complete all as specified.
1.1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%