Military Engineer Services Tender

Supplying, installing, testing & commissioning electrically operated passenger gearless lift INDRAVATI Building, 13 Passengers [884 KG capacity] to serve 10 Floors i.e. G + 9 upper floors in the existing lift well, confirming to all relevant IS, speed 2.0 metre/sec with automatic micro stroke button control, microprocessor based controller, simplex selective/ collective control suitable for 3 phase, 415 volts, 50 Hz, AC supply, independent operation with AC Variable Voltage Variable Frequency [AC VVVF] drive control [closed loop] with power saving regenerative drive with suitable gearless motor traction type to serve ground plus nine floors i.e. 10 stops and 10 landings with or without attendant, suitable for synchronised operation automatic power operated centre opening sliding type stainless steel doors 16 gauge with Mirror finish, Full toughend glass with two panel center auto door in mirror finish borders having full curtain infrared sensor safety, 3D infra red sensors for car doors along the full height, Automatic Rescue/ levelling Device [ARD] system with [±] 5mm and suitable batteries, Floor position digital indicators in car and all landing with call indicating lights, built in announcing system including necessary joists and beams for mounting the machine in machine room including addition/ alteration to existing lift well if any, all necessary civil works required in connection with erection of lift complete all as specified including dismantling of existing Lift complete alongwith its accessories of any description and transporting and depositing in MES stores and provision of temporary wooden door shutter at landing door opening for safety of the users till installation of new lift complete all as specified and as directed. Notes: The lift shall be provided with and including the following: [a] Fireman Switch [b] Automatic Rescue Device [ARD] during power failure including manual operation provision with suitable capacity of battery designed for running the lift with full load.

[c] Battery operated emergency light [LED Ceiling Fitting] alarm [speaker for emergency alarm system to be fixed] and stop button in car with rechargeable arrangement for battery. [d] Designer Six sleek circular LED light fitting 8 Watts x 6 Nos. in false ceiling. [e] Provision of one cross flow fan suitable for recessed mounting in false ceiling. [f] Provision of premium quality Jet black Granite stone slab of 18-20 mm thick as in flooring for lift car (Not more than two parts) over 3 mm thick aluminium chequered sheet. [g] Nonstop button/ independent operation. [h] Over load warning indicator with both audio and visual type with overload protection/ tripping system having relays , etc. [j] Front landing door operations with a minimum time of 10 sec and up to a maximum time of 30 seconds. [k] Stainless steel sliding doors with front opening for all Landings made of 16 gauge stainless steel sheet with Mirror finish with vision panel of size 350 X 1700mm covered with 8mm thick toughened plain glass. [l] All the dimensions of the lift and connected items shall be designed in conformity with IS 14665 standards and the contractor shall submit the design drawing to Accepting Officer for approval before commencementof work. The body shall be stainless steel of 16 gauge with Mirror finish with 38mm dia stainless steel hand rail with hairline finish. [m] Set of three in number limit switches at the bottom and top most position of lift hoist ways as specified in IS. [n] Stainless steel hand rail 38mm dia with hairline finish. [o] Specification plate with complete details [p Full length display indicator panel.

[q] Provision of suitable phase reversal relays to the controller to protect lift/ equipment against phase reversal, phase failure and low voltage. [r] Provision of Intercom. [s] Continuous earthing for machine and equipment [t] Steel Wire rope of adequate size as per relevant IS and as per manufacturers specification. [u] Other standard fixtures and fittings like guide rails, sheaves, counter weights with guards, buffers, gear unit brakes, control panel, car operational panel, governor, locks, power control and trailing cables complete all as per latest IS specifications. [v] Main drives and controls shall be high efficient and low power consumption. [w] Lift design, specifications, drawings, manufacturers instructions shall be got approved from Accepting Officer before placing order for procurement. [x] The contractor shall carry third party load testing for each lift installed once in every six months till defect liability period and shall submit staisfactory test results and the rate quoted shall be deemed to be included for this provision. [y] The Contractor shall shift the old dismantled lift to MES Storeyard as per direction of Engineer-in-Charge and the rate quoted shall be deemed to included transportation charges.