West Bengal Agro Industries Corporation Limited Tender

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups,binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape,placing in proper position and binding with 16 gauge black annealed wire at every inter-section. complete as per drawing and direction. (i) Tor steel/Mild Steel 1. SAIL/ TATA/RINL

Hire and labout charges for shuttering with centreing and neessatry staging upta 4 m. using approved stout props and thick hard wod planks ol approved thickness with required bracing for concTete slabs, beams, columns, lintels curved or straight inciuding titting, hXIng and striking out after completion of works. (upto roof of ground floor) (a) 25 mm. to 30 mm. thick wooden shuttering as per decision & direction ot Engineer-in-charge.

125 mm. thick brick work with 1st class bricks in cement mortar (4:1) in ground floor

Wood work in door and window frame fitted and fixed complete including a protective coat of painting at the contact surface of the frame. (c) Sal: Siliguri

Supplying fitting and fixing MS. clamps tor door and window rame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per directuon a) 40mm X 6mm, 250mm Length

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or rougening of concrete surface, including throating, nosing and drip course where necessary (ground floor) i) With 6:1 cement mortar (b) 20 mm. thick plaster

c)15 mm. thick plaster (6:1)

(ii) With 4:1 cement mortar (c) 10 mm. thick plaster

Supplying and laying true to line and level vitrified tiles off approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring plgment to match with Colour of tiles / epoxy grout materlals of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and directlon of Englineer-in-Charge. A) Deep Colour & White

Iron butt hinges of approved quality fitted and fixed complete. (vi) 100mm. X 50mm. X 1.25mm.

Anodised aluminium barrel/ tower/ socket bolt (full covered) or approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: (ii) 100mm long x 10mm dia. bolt.

Anodised aliminium D-type handle of approved quany manutactured from extruded section conforming to IS specification (I.S. 230/72) fitted and fixed complete: (a) With continuous plate base (Hexagonal/ Round rod) (vii) 150 mm grip x 12 mm dia rod

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hige and other fittings. (a) 50mm thick shutters with 25mm thick panel of size 30 to 45 cm (a) 1st class best Indian teak.

Protective and Decorative Acrylic exterior emulsilon paint of approved quality, as per manufacturer's specitication and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. b) Premium 100% Acrylic Emulsion

Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand(1.5mm thick)

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylie primer (as per manufacturer's specification) including cleaning and smoothening of surface, Two Coat

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. On timber surface.

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. On Steel Surface.

Painting with best quality synthetic enamel paint of approved make including & smooth finishing surtaces thoroughly.. Two Coats With super gloss (hi-gloss)- (a) On timber or plastered surface

With super gloss (hi-gloss) b) On steel or other metal surface:

M.S. or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq.mtr

Sub Total

GST 18%

CESS 1%