Military Engineer Services Tender

M&L for 40 mm thick consolidated thickness bituminous premixed carpet with 0.54 Cu.m per 10 sqm of stone chipping and mixed with 29.20 kg per 10 sqm of binder using paving bitumen grade 30 Pack (VG-30) laid and rolled with 8 to 12 tonne power road roller and compacted to required camber and gradient, complete all as specified and directed.

M&L for liquid seal coat by applying paving bitumen of grade 30 (VG-30) @ 9.8 kg per 10 Sqm blinded with 6.3 mm size stone chipping @ 0.09 cum per 10 Sqm and rolled to a uniformed smooth surface by 8 to 12 tonne power road roller, complete all as specified and directed.

Providing and lying Mastic Asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29 using approved coarse aggregates, fine aggregates filler materials and bitumen, prepared by using Mastic cooker including cost and carriage of all ingredients, cost of heating aggregates and binder mixing in specified proportions conforming to approved job mix formula and laid to required level and slope after cleaning the surface, compacting, sealing the construction joints and surface finishing conforming to specifications including providing antiskid surface with bitumen pre-coated fine arraigned hard stone chipping of 13.20mm nominal size at the rate of 0.005 cum per 10 sqm and at an approximate spacing of 10 cm Centre to Centre in both directions, pressed into surface when the temperature of surfaces not less than 200C, protruding 1 mm to 4mm over mastic surface including the hire charges of all tools and plants and machinery, pay of operators, cost of fuel and lubricants and quality control all complete as per clause 516 of specification for road and bridge works of MORTH (5th Revision). 25mm thick (Pakur) VG-30 (PO, 10/20 (P), complete all as specified and directed.

Supply and fixing of cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions and all as specified and directed.

M&L for applying thermoplastic road marking paint of approved colour upto 10cm width in edges of road with 2.75mm or more thickness, applied using mechanically propelled vehicle consisting heated hopper mounted on a pram, which feeds hot molten thermoplastic under gravity to a rectangular screed with a gate at the base whose opening is set to produce the thickness, complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, all as specified and directed.

M&L for 100mm thick plain cement concrete(1:3:6), type C-2 (40 mm graded stone aggregate) as in sub-base, floor, plinth protection, hard standing, paving etc., complete all as specified and directed.

M&L for sand filling under floors or in foundations or sand cushioning (40mm thick) including spreading, levelling, watering and consolidation, complete all as specified and directed.

M&L for providing machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement and pigment, complete all as specified and directed.

M&L for providing machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment, complete all as specified and directed.

M&L for providing cement concrete (1:3:6), type C-1, (using 20 mm graded aggregate) as in coping /parepet wall/bed plate /Kerb stone etc with plain fair faces including chamfers, weathering, slightly rounded or chamfered angles and throating, including necessary form work complete all as specified and directed.

Note 1:- (Applicable for all parts/items) : The bidders/contractors are advised to read tender document, all drawings & all corrigendum / amendments and general condition of contracts before entry / quoting the rates. Note 2:-The contract sum shall be arrived at after deducting amount of schedule of credit from the total quoted amount.