Military Engineer Services Tender

Removing excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5m above the starting point in any type of soil, complete all as specified and directed.

M & L for PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) for foundation, filling, mass concrete, foundation of pole/struts etc. including necessary form work, complete all as specified and directed.

M & L for PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in sub base DPC etc, complete all as specified and directed.

M&L for brick work with flyash bricks, old size, straight or curved on plan exc 6 mtr mean radius built in CM (1:6), complete all as specified and directed.

M&L 15mm thick rendering in CM (1:6) on fair faces of brick work or concrete surfaces of wall, finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 15mm thick in two coats (10mm in 1st layer & 5mm in top layer) on fair faces of brick work or concrete surfaces of wall in CM (1:4), mixed with integral water proofing compound in top layer as per manufacturer's instructions and finished the surface even and fair without using extra cement, complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item as supply only.)

Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification, complete all as directed

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash, complete all as specified and directed.

M&L for preparation new plastered surfaces of wall and applying two coats of 100% premium acrylic weather proof exterior emulsion paint, alkali & fungal resistance, approved coloure and shade (pattern deep green/camouflage), over and including a primming coat of exterior emulsion primer as per manufacturer's instructions, complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick light shade (square/ rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick light shade (square/ rectangular) area of each tile not exceeding 0.36 sqm, on vertical surfaces such as skirting dados etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match over and including 10mm thick rendering in CM (1:4), complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement of match over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350 x 250 x 7mm/450 x 300 x 7mm thick on vertical surfaces such as skirting or dados etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4), complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, fixed in opening as per specification, complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification, complete all as specified and directed.

S&F 150mm long aluminium barrel tower bolts of extruded section, complete all as specified and directed

S&F 100mm size butt hinge, medium weight, cold rolled, mild steel, complete all as specified and directed.

S&F 100mm long aluminium handle, cast type anodised, complete all as specified and directed.

S & F powder coated (minimum thickness of powder coating 50 micron) aluminium anodised door comprising of frame of size 101.60mm x 44.6mm x 2.4mm thick push/pull type glazed door shutter having top and bottom section of size 83 x 44.5 x 2.4mm and 100 x 44.5 x 2.4mm thick respectively, styles section of size 80 x 44.5 x 2.4mm thick and lock rail of size 100mm x 44.5mm x 2.4mm thick including necessary jointing cleat, glazing clips, rubber packing, anodised aluminium snap beading, screws of suitable size including 5mm thick tinted sheet glass in both panel, hinges, mortice lock, stays & aluminium anodised handle of suitable size, etc, complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) aluminium anodised sliding window shutter frame comprising of 3 track sliding window made out of aluminium extruded section of bottom frame of weight not less than 1.175 kg/RM, top and side frame of weight not less than 0.423 Kg/RM, top and bottom rail of shutter of weight not less than 0.336 Kg/RM, in two panel and shutter with and including 5mm thick selected quality tinted glass and third one with and including stainless steel wire mesh and overall aluminium decogrill of size 100 x 100 x 8mm as approved by GE with standard aluminium channel out side, with and including handles, cleat glazing clips, special auto lock, dry set rubber gasket, complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) aluminium work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections/appropriate 'Z' sections and other section of approved make conforming to IS-733 and IS-1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at junctions, i.e. at top bottom and sides with required EPDM rubber/neoprene gasket. aluminium sections shall be smooth rust free straight mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/paneling, CP brass/stainless steel screws, complete all as specified and directed.

S&F 3mm thick ACP (aluminium composite panel) sheet, wooden finish, in aluminium frame including all nessesary fittings, complete all as specified and directed.

S&F 10mm thick toughened glass, as in partition, fixed to aluminium section, including cutting to shape, drilling holes, as required, complete all as specified and directed.

S&F CPVC pipe of size 16mm dia, SDR 11 & plain CPVC SDR 11 fittings complete, fixed on wall/ceiling or laid in floors with necessary saddle/clamps including all necessary fittings like elbow, tee, socket, reducer, etc. fixed with necessary solvent cement, complete all as specified and directed.

S&F CPVC pipe of size 20mm dia, SDR 11 & plain CPVC SDR 11 fittings complete, fixed on wall/ceiling or laid in floors with necessary saddle/clamps including all necessary fittings like elbow, tee, socket, reducer, etc. fixed with necessary solvent cement, complete all as specified and directed.

M&L for cutting chases, pinning in making good to facing where required and pointing in CM (1:3) to ends to facings where required and pointing in CM (1:3) to ends or edges of landings, steps, cills , sunshades,shelves, lintesl etc and cutting chases for cncealed water tubing or concealed conduit wiring etc and making good as per existing surface cutting not exc 10cm girth in brick walls, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks, triple layered, (cylindrical vertical with closed top) ISI marked, confirming to IS 12701-1989, hoisted and fixed in position all as specified in SSR Part I (1000 ltr capacity) including 20mm Nipple suitable for HDPE water tank including 20mm bore ball valve, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed to 20mm bore pipe, complete all as specified and directed.

S&F 15mm bore bib taps, cast copper alloy, chromium plated, two in one, with crutch or butterfly handle, screwed down, screwed for iron pipe, compelete all as specified and directed.

S&F 600mm x 450mm bevelled edge mirror made of selected quality sheet glass not less than 5.5mm thick, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed.

S&F vitreous china wash hand basin, oval shape,pastel, flat back of size 580 x 450mm including chain, plug & procelain stopper and pinning in ends of brackets etc, complete all as specified and directed.

S&F vitreous china bowl urinal half stall type, white, with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including urinal spreader, providing and fixing plugs, bedding urinal against wall in CM (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, complete all as specified and directed

S&F vitreous china EWC water closet pan, white and including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe with seat and cover and flushing cistern & flush pipe including making good distrubed surfaces/damaged, complete all as specified and as directed.

S&F waste fittings 32mm bore, brass, chromium plated for wash basins/sink etc with long screwed shanks and fly nuts, flange and bed deal in red lead cement and other end, complete all as specified and directed.

S&F PVC connection 15mm size of length 600mm with PTMT nuts, complete all as specified and directed.

S&F 15mm bore bib taps, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe, compelete all as specified and directed.

S&F 15mm bore, fancy type, chromium plated, stop valves with long shank and cup, concealed type, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union, complete all as specified and directed.

S&F CP pillar tap, 15mm bore, capstan head, screwed down high pressure with or without lettered “hot’ or “ cold” with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

S&F for 15mm dia pipe, health faucet (ABS Body) mild steel chromium plated suitable with 1.25 metre long flexible tube and ABS wall hook including makeing connection and fixed in position, complete all as specified and directed.

S&F 600mm towel rail of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms), complete all as specified and directed

S&F towel ring of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms), complete all as specified and directed

S&F shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms), complete all as specified and directed

S&F swivel shower rose of PTMT, any colour, with arm 15mm size, 195mm long with bend of 45 degree with flange for fixing with 15mm bore pipe (minimum weight of shower 40 gms and shower arm 40 gms), complete all as specified and directed.

S&F 140mm grating round of PTMT (minimum wight - 50 gm), complete all as specified and as directed.

S&F 100m dia cast iron nahani trap, with grating including jointing to waste pipe fixed in CM (1:2:4) type B2 (using 20mm graded crushed stone aggregate), complete all as specified and as directed.

S&F 110mm bore, PVC (SWR), soil waste and vent pipes, in any length with cement joints fixed to wall with all necessary fixing arrangement, complete all as specified and directed.

S&F 110mm bore, PVC (SWR) bends of any radius, complete all as specified and directed.

Supply and laying in trenches of reinforced concrete pipes, class NP2, laid and jointed complete with collars, complete all as specified and directed.

M&L for hardcore of gauge not exceeding 63mm of broken stone, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified and directed. (Note : Compacted volume shall be measured for payment).

M&L for 100mm thick PCC (1:3:6) type C- 2 (using 40mm graded crushed stone aggregate) as in floors & pavings or plinth protection, path, hardstanding etc., complete all as specified and directed.

M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C- 2 (using 40mm graded crushed stone aggregate) as in floors & pavings or plinth protection, hardstanding etc. (finished without using extra cement), complete all as specified and directed.

Supply only chain link MS galvanisd fencing, any size 75 x 75mm / 100mm x 100mm, complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire, complete all as specified and directed.

S&F rolled mild steel in stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc of Fe-290, E-265 including distance pieces, cleats etc, complete all as specified and directed.

M&L for MS framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing, Fe-290, Gde E-165, complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer, complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating, GI based plain steel sheet 0.50mm thick, of any colour, having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws, complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating, GI based corrugated steel sheet 0.50mm thick, of any colour, having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws, complete all as specified and directed.

S&F for 605 x 605mm GI frame work for seamless ceiling comprising of Gl perimeter channnel 0.55mm thick with two unequal flanges of 20 and 30mm and web of of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre, hanger with 4-6mm dia GI (length as required) adjusting level fixed to roof slabs/truss by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expension hold fast evers 12.5mm dia 40mm long including providing 6mm thick non asbestos fibre cement building board fixed or laid/ inserted to GI framework with screws, for fixing 600mm x 600mm grid, complete all as specified and directed.

Taking out existing plaster and removing of debris to a distance exc. 100m and n. exc. 250m and cleaning roof surfaces to remove all loose dust etc., roughening surfaces of old concrete roof by picking, sweeping clean and washing down with water using wire brush, brooming down and applying the following treatment all as directed in order of precedence as stated : (a) Brushing neat cement slury with 3.50 kg of cement per Sqm. (b) 15mm thick screed bed or bedding layer in CM (1:3) mixed with water proofing compound as per manufacturer instruction on existing roof surface, true to level. (c) Applying one coat of cold bituminous primer over screed bed @ 400ml/Sqm confirming to IS-3384 (d) Supply and laying 3mm thick APP based polymeric membrane of approved manufactured with weight not less than 3.50 Kgs per Sqm reinforced with non-woven polyester fabric weighing not less than 160gms per Sqm having softening point not less than 15°C, having tensile strength of 650 N/Sqcm and 350 N/Sqcm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180 N by torch application. Polymeric membrane shall be taken to a height of 30cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (e) Applying one coat of green weather coat paint @ 0.11 Kg/Sgm over APP membrane surface. Note:- (i) Laying APP based polymeric membrane shall be done torch on method as per manufactures instructions. (ii) A minimum overlap of 150mm and 100mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturers instruction. (iii) APP based polymeric membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given in IS 16540-2017/1S 16532 2017. (iv) Contractor shall produce necessary test certificate of the manufacturer to the Engr-in-Charge before incorporation in the work. (v) Necessary independent tests shall also be carried out by the contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work. (vi) The work shall be executed through authorised applicators of original manufacturer only. (viI) WPC shall be measured and paid separately as supply only.

M& L for point wiring with 1.5 Sqmm PVC insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, ISI marked, FRLSH type drawn through and including PVC casing /caping (ISI marked) of adequate size (not less than 20mm) and its accessories with sunk cast iron/pressed steel terminal boxes of size 1.6mm thick for one light or one fan point controlled by one switch incl 1.5 Sqmm (nominal area) copper conductor cable (multistrand), FRLSH type, PVC insulated and unsheathed with colour code earth wire connected to common earth dolly at one end and metalic bodies of luminaires/ fan at other end for one light point/one fan point controlled by one light/fan/exhaust fan, one way switch, complete all as specified and directed.

All as per item No 64.00 here-in before but one 5 Amp 5 pin socket outlet point on same board, complete all as specified and directed.

All as per item No 64.00 here-in before but one 5 Amp 5 pin socket outlet point on independent board but not below the switch board of the light point in the same vertical plane, complete all as specified and directed.

All as per item No 64.00 here-in before but with 2.5 Sqmm PVC insulated unsheathed multi stranded cable FRLSH type for one 15 Amp 3 pin socket outlet point including PVC insulated 2.5 Sqmm FRLSH type copper multi stranded conductor as earth wire on independent board, complete all as specified and directed.

S&F ceiling rose, surface bakelite PVC/ polycarbonate, isolated body with three terminals, complete all as specified and directed.

S&F switch, modular type, single pole, one way, 6 Amp, one module, complete all as specified and directed.

S&F socket outlet, modular type, multipurpose having provision for 2/3 pin, 6 Amp and combined, 2 module, complete all as specified and directed.

S&F two socket outlet, modular type, heavy duty, multipurpose having provision for 6 pin, 6/16 Amp, 2 module, complete all as specified and directed.

S&F switch, modular type, single pole, one way, 16 Amps, one module, complete all as specified and directed.

S&F modular cover plate with frame including metal flush box, 3 module, white, completes all as specified and directed.

S&F modular cover plate with frame including metal flush box, 4 module, white, completes all as specified and directed.

S&F modular cover plate with frame including metal flush box, 8 module, white, completes all as specified and directed.

S&F MCB distribution board (DB), SPN with sheet metal encloser, double door, IP 43 protection, 240 volts, 4 way, IP 43 & IK 09 with metal door with 200 Amps rated copper busbar (as per OEM), neutral link for fixing MCBs/Isolators, completes all as specified and directed.

S&F MCB distribution board (DB), SPN with sheet metal encloser, double door, IP 43 protection, 240 volts, 8 way, IP 43 & IK 09 with metal door with 200 Amps rated copper busbar (as per OEM), neutral link for fixing MCBs/Isolators, completes all as specified and directed.

S&F MCB SP 6 to 32 Amps, 240V, 10 KA, 'C' curve, including connection and testing, completes all as specified and directed.

S&F MCB SPN 40 Amps, 10 KA, 'C' curve, including connection and testing, complete all as specified and directed.

M&L for submain wiring wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLSH type, cables 4 Sqmm drawn in and including heavy duty PVC conduit (ISI marked) not less than 20mm dia with fixing accessories including 4 Sqmm 1100 Volts grade, FRLSH type, PVC insulated unsheathed multistranded flexible copper conductor cable as continuous earth wire and connecting to common earth dolly, complete all as specified and directed. Note:-Three runs of cable and one run PVC conduit including accessories shall be measured as one length of sub main.

M&L for submain wiring wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLSH type, cables 6 Sqmm drawn in and including heavy duty PVC conduit (ISI marked) not less than 20mm dia with fixing accessories including 6 Sqmm 1100 Volts grade, FRLSH type, PVC insulated unsheathed multistranded flexible copper conductor cable as continuous earth wire and connecting to common earth dolly, complete all as specified and directed. Note:-Three runs of cable and one run PVC conduit including accessories shall be measured as one length of sub main.

S&F LED lights fitting 1 x 18 W, 220V, AC, with driver, LED rod complete connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F exhaust fan, steel body AC, single phase, 230V of size 450mm sweep with, blades, and frame & louvers including cutting wall for making hole for fixing the exahaust fan and making good the opening in CM (1:3) or PCC (1:2:4) type B1, as required at site, completes all as specified and directed.

Supply and errecting steel tubular swaged poles type 410 SP-22 (9 metres long) complete with mild steel base plate, finial taper plug, bolts, nuts & screws as per IS 2713 (part-II) 1980 made out of mild steel tubing including earth work, PCC, painting of pole with two coats of aluminium paint over a coat of red oxide primer, drilling hole for passing of cable from bottom to top and marking pole No. on pole including GI bracket 1.5m long for fixing light fittings, completes all as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide and not exc 1.5 metre in depthand n. exc. 10 Sqm on plan, for foundation of pole/stay, or cable trenches etc and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in incl spreading, leveling watering and well ramming in layers not exceeding 25cm in soft/loose soil, complete all as specified and directed.

Removing excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point in any type of soil, complete all as specified and directed.

Supply and laying double walled corrugated (DWC) HDPE duct pipe of 40mm dia conforming to IS, approved colour complete with fittings for cable protection, complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sqmm 4 core, complete all as specified and directed.

S&F LED street light fittings 90 watt 230 V AC outdoor type with high pressure dia cast aluminium housing and heat-resistant complete with driver, lamp bracket with impact and corrision resistant, IP 65/66 protection, complete all as specified and directed.

S&F in repair KIOSK box weather proof made out of PVC and including one piece mounted SMC base and door pole mounted hinged door size 333 x 233 x 200mm out side and 300 x 200 x 105mm inside dimension comprising of aluminum bus bar 4 strips for 3 phase and neutral 63 Amp and 10 Amp MCB for controlling the street light fitting including FI clamps 30 x 4mm with necessary MS nuts bolts and washer including embossing/painting of danger notice of size not less than 10cm x 7.5 cm with letters, figures and conventional skull and bones in signal red colour on front face of KIOSK box body, complete all as specified and directed.

S & F 3 core PVC insulated unsheathed multistranded copper conductor cable of size 1.5 Sqmm passing through PVC conduit from junction box to fittings, complete all as specified and directed.

S&F LED flood light fitting 120 Watt 230 volt, AC outdoor type with thermal management in multiple optics with impact and corrosion resistant complete with driver and lamp, IP 65/66 protection, complete all as specified and directed.

S&F post top lantern LED type 40/45 Watt 230 volt, AC outdoor type with decorative post top for 360 degree indirect light, with impact and corrosion resistant complete with driver and lamp, IP 65/66 protection, complete all as specified and directed.

M&L for PCC (1:2:4), type B-1. (using 20mm graded crushed stone aggregate) as in benching, coping, bed plate, lintel, benching/foundation etc. including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified and directed.

Horizontal boring under the road (with manual method) below 1mtr from the road surface and dia of hole not exc 100mm, with out damaging the existing road, getting out and disposal of soil to a distance not exceeding 50m from the site of work, complete all as specified and directed.

M&L for earthing complete with GI earth plate electrode 60 × 60cm × 6mm thick , buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to existing earth lead strip by means of bolts, nuts, check nuts and washers of brass or HS steel all as shown in electrical plate No. 3 connected to earthing test point and and necessary excavation and earth work PCC (1:3:6) type C-1 as earth pit with pre-cast RCC (1:2:4) type B-1 cover slab size 400 x 400 x 50mm reinforced with 8mm dia TMT bar, 100mm c/c both ways including one handle made of 12mm dia including providing charcoal or coke and common salt in alternate layer of 15cm compacted thickness all around the earth electrode with funnel and 20mm bore galvanized iron watering pipe (light grade) wire mesh, copper lugs, complete in all respect, including galvanised iron earth strip 25 x 4mm, protected by 40mm bore (medium grade) galvanized iron pipe up to earthing test point as directed, incl disposal of spoil to a distance not exc. 50 mtr and necessary testing on completion, complete all as specified and as directed. Note : (i) Proper earthing pit should be provided with pit cover. (ii) GI earth strip beyond 7.5 mtr shall be measured and paid seperately.

Supply and install hi wall split type Air conditioning units 2 TR indoor/outdoor complete with cordless remote control unit and with in built air ionisor and plasma filter for better indoor air quality with 5 star rated and EER 3.2/BLDC type compressor unit including suction/discharge tube with proper insulation, complete with all piping arrangment, etc complete all as specified and directed. Note : (i) Condensate drain pipe of best quality to be provided and fixed in suitable manner till ground level/max up to 6.0 Mtrs fixed on wall/floor/ceiling and quoted rate shall deemed to be included for the same. (ii) The quoted rate includes necessary fixing arragement for indoor and outdoor units and copper tubing upto 6.00 mtr length, brazing, welding including insulation, complete charging of refrigerator gas upto required level, filling the cavities on wall, setting of grill alignment including testing & commissioning, complete all as specified and directed.

Supply and install hi wall split type Air conditioning units 1.5 TR indoor/outdoor complete with cordless remote control unit and with in built air ionisor and plasma filter for better indoor air quality with 5 star rated and EER 3.2/BLDC type compressor unit including suction/discharge tube with proper insulation, complete with all piping arrangment, etc complete all as specified and directed. Note : (i) Condensate drain pipe of best quality to be provided and fixed in suitable manner till ground level/max up to 6.0 Mtrs fixed on wall/floor/ceiling and quoted rate shall deemed to be included for the same. (ii) The quoted rate includes necessary fixing arragement for indoor and outdoor units and copper tubing upto 6.00 mtr length, brazing, welding including insulation, complete charging of refrigerator gas upto required level, filling the cavities on wall, setting of grill alignment including testing & commissioning, complete all as specified and directed.

S&F voltage stabilizer of capacity 5 KVA for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5%, with digital display automatic high and low cut out with wall mounting accessories, complete all as specified and directed.

S&F single pole and neutral encloser with a two pin and earth plug and socket complete with one MCB SP 20 Amps, 'C' curve, complete all as specified and directed.

Supply and fixing energy efficient ‘LED Flood Light 120 W LED luminaire with Aluminium dia cast housing, toughened glass cover with IP 66 protection, CCT 5700 K including fixing arrangment on wall/pole / surface and connecting cable up to nearest ceilign rose into flexible PVC conduit. Make : Crompton/Havells/ Surya/Philips