Military Engineer Services Tender

75 Sqmm to 120 Sqmm, 3.5 core

150 Sqmm to 185 Sqmm, 3.5 core

240 Sqmm to 400 Sqmm, 3.5 core

Excavation in trenches not exc 1.5 metre width and not exceeding 1.5 metre in depth in soft/loose soil and getting complete all as specified and as directed.

Excavation of trench in road/hardstanding etc, not exc 1.50 m wide and not exc 1.50 m deep and getting out complete all as specified and directed.

Returning, filling in including spreading levelling watering and well ramming in layers n.exc 25 thick for soft/loose soil complete all as specified and as directed.

Removal of excavated material to a distance n.exc 50 metre and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed.

Supply Laying double wall corrugated HDPE Pipe 120mm Outer Dia, confirming to IS-16205 (Part-24) with couplers end cap & bends as required, laid in trenches for cable protection complete all as specified and directed

Supply Laying double wall corrugated HDPE Pipe 120mm Outer Dia, confirming to IS-16205 (Part-24) with couplers end cap & bends as required, laid in trenches for cable protection complete all as specified and directed

Taking out carefully interlocking paver block, of any size or shape and re-laying in the same position after relaying of LT Cable, duly removing all vegetation, algae, grass etc., laid in proper slope and gradient over sand cushioning, complete all as specified and directed. Note: Sand, if required for correction of cushioning level shall be measured and paid separately. Replacement of broken paver blocks shall be separately as "Supply only"

Supply and laying machine pressed precast concrete interlocking paver block with grey cement and pigment of any shape and size as approved by GE conforming to IS-15658-2006 of 60 mm thickness, M-35 grade with 6 mm top layer of coloured rubberised anti abrasive material complete all as specified and directed.

Relaying of XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured electric power cable 1100 Volts grade with stranded aluminium conductor cable, laid in trench or fixed to wall / passing through pipe/ pole. (retrieved against item No 1 above) after fault rectification incl necessary aluminium thimbles, jointing and testing complete all as directed by the Engr-in-Charge of the following sizes :- (Note :- Necessary earth work to be measured and paid separately.

10 Sqmm to 16 Sqmm, 2/3.5/4 core

25 Sqmm to 50 Sqmm, 3.5 core

70 Sqmm to 120 Sqmm, 3.5 core

150 Sqmm to 185 Sqmm, 3.5 core

240 Sqmm 4 core to 400 Sqmm, 4 Core

Supply, Laying and testing XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured electric power cable 1100 Volts grade with stranded aluminium conductor cable, laid in trench or fixed to wall/passing through pipe/pole incl necessary aluminium thimbles, jointing and testing complete of the following sizes and cross sectional area :- (Note :- Necessary earth work to be measured and paid separately.

35 Sqmm, 3.5 Core

50 Sqmm, 3.5 Core

95 Sqmm, 3.5 Core

120 Sqmm, 3.5 Core

150 Sqmm, 3.5 Core

185 Sqmm, 3.5 Core

240 Sqmm, 3.5 Core

S&F heat shrinkable straight through Joints using suitable jointing Kit suitable for 1100 volts grade XLPE insulated stranded aluminium conductor cable including testing on completion complete all as specified and directed by the Engr-in-Charge for the following size of cables :-

25 Sqmm to 50 Sqmm, 3.5/4 Core

70 Sqmm to 150 Sqmm, 3.5 Core

185 Sqmm to 240 Sqmm, 3.5 Core

300 Sqmm to 400 Sqmm, 3.5 Core

Dismantling/ Disconnecting electric connection of underground LT, XLPE Cable, 1100 volts upto 35 to 400 Sqmm from both sides and locating the fault in LT cable with fault locating machine in the entire length up to 1 Km complete testing after reconnecting and commissioning of cable complete all as specified and as directed. Note : The work will be executed after obtaining proper shutdown from Substation liase with JE E/M.

Supply and fix (in replacement) ACB, 800 amps, 4 pole, with microprocessor based release, Ics=50% of Icu, manual drawout type, with overload, short circuit & ground fault protections with inbuilt display for current metering with high accuracy of class 1, internal battery, communication port, inbuilt USB port for software diagnosis, all accessories incl taking down existing ACB complete all as specified and directed. Make: L&T / LEGRAND / SCHNEIDER/ ABB / C&S / SIEMENS or equivalent make specified in tender.

S&F in repair MCCB 630 Amps, 4 pole, 50 kA, 415 Volts, with microprocessor based release with electronic Sg (LSg) protection unit, Ics=100% of Icu with overload, short circuit & ground fault protections with in built display for current metering with high accuracy of class 1, internal battery, communication port, inbuilt USB port for software diagnosis, with all accessories, complete all as specified and directed. Make: L&T / LEGRAND / SCHNEIDER/ ABB / C&S / SIEMENS or equivalent make specified in tender.

S&F in repair MCCB 400 Amps, 4 pole, 50 kA, 415 Volts, with microprocessor based release with electronic Sg (LSg) protection unit, Ics=100% of Icu with overload, short circuit & ground fault protections with in built display for current metering with high accuracy of class 1, internal battery, communication port, inbuilt USB port for software diagnosis, with all accessories, complete all as specified and directed. Make: L&T / LEGRAND / SCHNEIDER/ ABB / C&S / SIEMENS or equivalent make specified in tender.

S&F in repair MCCB 320 Amps, 4 pole, 36 kA, 415 Volts, with adjustable type, Ics=100% of Icu, with all accessories & copper spreader complete all as specified and directed. Make: L&T / LEGRAND / SCHNEIDER/ ABB / C&S / SIEMENS or equivalent make specified in tender.

S&F in repairs of MCCB 4 Pole, 415 V, Adjustable type 250 Amps with breaking capacity 36 KA, Ics=100% of Icu with all accessories incl taking down existing MCCB complete all as specified and directed Make: L&T / LEGRAND / SCHNEIDER/ ABB / C&S / SIEMENS or equivalent make specified in tender.

S&F in repair MCCB 200 Amps, 4 pole, 25 kA, 415 Volts, with adjustable type, Ics=100% of Icu, with all accessories & copper spreader complete all as specified and directed. Make: L&T / LEGRAND / SCHNEIDER/ ABB / C&S / SIEMENS or equivalent make specified in tender.

S&F in repair MCCB 160 Amps, 4 pole, 25 kA, 415 Volts, with adjustable type, Ics=100% of Icu, with all accessories & copper spreader complete all as specified and directed. Make: L&T / LEGRAND / SCHNEIDER/ ABB / C&S / SIEMENS or equivalent make specified in tender.

S&F in repair MCCB 100 Amps, 4 pole, 25 kA, 415 Volts, with adjustable type, Ics=100% of Icu, with all accessories & copper spreader complete all as specified and directed. Make: L&T / LEGRAND / SCHNEIDER/ ABB / C&S / SIEMENS or equivalent make specified in tender.

S&F in repair MCCB 63 Amps, 4 pole, 25 kA, 415 Volts, with adjustable type, Ics=100% of Icu, with all accessories & copper spreader complete all as specified and directed. Make: L&T / LEGRAND / SCHNEIDER/ ABB / C&S / SIEMENS or equivalent make specified in tender.

Dismantling carefully serviceable isolating LT Panel board of sizes 1500mm x 900 mm x 600 mm to 2500 mm x 2000mm x 900 mm, duly unscrewing/ opening front and back cover and cleaning complete bus bar chamber, tightening all the nuts, bolts incoming and outgoing terminals including cleaning the all switchgear/ accessories and replacement of cable gland and replacement of stainless steel hinges of size 100mm for panel board door fixed with welding machine incl applying one coat of synthetic enamel paint externally to panel board after scrubbing/cleaning the surface complete testing the Panel board till satisfaction of Engr-in-Charge, complete all as specified and directed.

S&F Cable Route Indicator made out of Cast Iron plate 80 mm dia fixed with MS angle iron 40x40x6mm having 60 Cm long showing MES LT Cable Size with voltage with two coats of synthetic enamel paint in blue colour over one coat of primer necessary Earth Work and Cement Concrete 1:2:4 (20mm graded crushed stone aggregates) Block of size 20x20x20 Cm including Taking out Unserviceable Cable Route Indicator, complete all as specified and as directed.

Dismantling / Disconnecting electric connection of UG LT XLPE cable, 35 Sqmm to 400 Sqmm, 1100 Volts grade, for finding the earth fault from both sides of cable and locating the fault in LT cable with fault locating machine in the entire length, complete testing after reconnecting and commissioning of cable, complete all as specified and directed. (NOTE: The testing shall be conducted only after obtaining the proper shutdown from the Main Power House, in the prengence of GE / Engineer-in-Charge)

Supply and fixing in repair Motorised Changeover switch open execution type, 415V, 3 phase 4 pole 125 Amps with AST Controller with wire harness to be fixed on existing panel board all as directed by Engr-In-Charge Make : L&T Cat Part No. CK90161B000 + CK901920000 or equivalent make specified in tender.

Supply and fixing in repair Motorised Changeover switch open execution type, 415V, 3 phase 4 pole 200 Amps with AST Controller with wire harness to be fixed on existing panel board all as directed by Engr-In-Charge Make : L&T Cat Part No. CK90161B000 + CK901920000 or equivalent make specified in tender.

Supply and fixing in repair Motorised Changeover switch open execution type, 415V, 3 phase 4 pole 400 Amps with AST Controller with wire harness to be fixed on existing panel board all as directed by Engr-In-Charge Make : L&T Cat Part No. CK90161B000 + CK901920000 or equivalent make specified in tender.

Supply and fixing in repair Motorised Changeover switch open execution type, 415V, 3 phase 4 pole 630 Amps with AST Controller with wire harness to be fixed on existing panel board all as directed by Engr-In-Charge Make : L&T Cat Part No. CK90161B000 + CK901920000 or equivalent make specified in tender.

Supply and fixing GI tubing 50mm bore (light grade) in trenches/floor/fixed along pole for cable incl taking down old unsv pipe complete all as specified and directed.

Supply and fixing 80 mm bore galvanized iron pipe (light grade) with all fittings, fixed in trenches/floor/fixed along pole for cable incl taking down old unsv pipe complete all as specified and directed.

Supply and fixing 100 mm bore galvanized iron pipe (light grade) with all fittings, fixed in trenches/floor/fixed along pole for cable incl taking down old unsv pipe complete all as specified and directed.

Dismantling carefully serviceable isolating LT Panel board of sizes 1500mm x 900 mm x 600 mm to 2500 mm x 2000mm x 900 mm, duly unscrewing/ opening front and back cover and cleaning complete bus bar chamber, tightening all the nuts, bolts incoming and outgoing terminals including cleaning the all switchgear/ accessories and replacement of cable gland and replacement of stainless steel hinges of size 100mm for panel board door fixed with welding machine incl applying one coat of synthetic enamel paint externally to panel board after scrubbing/cleaning the surface complete testing the Panel board till satisfaction of Engr-in-Charge, complete all as specified and directed.

Taking out unserviceable LT panel board / FEEDER PILLER box (of any size) and Supply, install, commissioning and testing of Outdoor type LT panel board, cubical type, dust and vermin proof, made out of 3.15 mm thick CRCA sheet of size 1000mm x 1200mm x 500mm, CPRI approved with front and back openable door (with locking arrangement) and making compartment for each MCCB separately, duly painted with two coats of powder coated paint over a coat of red oxide zinc chrome primer inclusive of four numbers aluminium bus bar 500 Amps of suitable size (of adequate length), for three phase and neutral system, fixed over and including 4 no's insulators, pre-wired with PVC insulated stranded copper conductor (of adequate size), all incoming / outgoing connection to be made with aluminium lugs and strips, with provision of cable entry and exit at mid portion of the panel board (with cable gland),and 02 Nos Danger Notice Plate (of size 20 cm x 15 cm, suitable for LT line, made out of 0.6 mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour, fixed with angle iron frame with base 40 x 40 x 6 mm with legs not more than 450mm long including grouting with PCC (1:2:4) complete including earthing all as directed by the Engr-in-Charge including supply and fixing of the following accessories:- Make : Star Electric & Engg Co/ CPRI approved.

MCCB design with thermal-magnetic releases of capacity 320A, 4P, 36 KA - 01 No (Incoming).

MCCB design with thermal-magnetic releases of capacity 100 Amps, 25 KA - 04 Nos (Outgoing).

MCB SPN 63 Amps - 02Nos.

Digital Ammeter with Selector Switch - 01 No

Digital Voltmeter with Selector Switch - 01 No

MCB SP 6 Amps, 10 KA - 01 No

LED type indication lamp R Y B - 01 set.

Current Transformer Ratio 400/5A - 03 Nos

Note:-(i) All incoming and outgoing cables, duly thimbled along with suitable size of brass cable glands, to be connected with accessories. (ii) All MCCB & Automatic Transfer Switch to be connected internally with suitable size of aluminium strip. (iii) All requisite accessories including spreader terminals shall be provided alongwith MCCBs and cost of the same shall be deemed to be inclusive in the quoted rates

M&L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanized iron strip 25 X 4 mm (upto 7.5 metres) by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 45 cm x 45 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 40 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing and dismantling of existing unsv earthing complete all as shown in Figure 15A of IS 3043 :1987, complete all as specified and directed.