Military Engineer Services Tender

Excavating over areas, n.exc 1.5 m deep and getting out in soft/loose soils complete all as specified and directed.

Moorum/red bajri filling in floors or in foundation, laid in layers n.exc 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for Hardcore of gauge n.exc 63mm, deposited, spread and leveliled in layers n.exc 150mm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC type D2, 1:4:8 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for 100mm thick Cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in floors, fisnished even and smooth without using extra cement complete all as specified and directed.

M&L for Forming Contraction (Dummy) joints 50mm deep x 10mm wide, filled with sealing compound Grade 'B' complete all as specified and directed.

M&L for Reinforced Cement Concrete (Design Mix) M-25 using 20mm graded aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for Reinforced Cement Concrete (Design Mix) M-25 using 20mm graded aggregate in Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for Reinforced Cement Concrete (Design Mix), M-25 in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for type B-1 1:2:4 (using 20mm graded stone aggregate) providing RCC precast cement concrete as in cover slab for man hole and similar article with plain face set in cement mortar 1:6 complete all as specified and directed.

S&F Mild Steel TMT bars 10mm and over, cut to lenghth, bent to shape requird, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clip all as directed by Engr-in-Charge.

M&L for Mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finihed surfaces complete all as specified and directed.

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces complete all as specified and directed.

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surfaces complete all as specified and directed. .

M&L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete, all as specified and as directed.

M&L for Rendering 15mm thick in CM (1:4) using liquid waterproofing compound as per manufacturer instruction on fair faces of brick work or concrete surfaces of wall finished fair and even complete all as specified and directed. (Note: WPC shall be measured and paid separately).

M&L for Rendering 5mm thick in CM (1:3) on fair faces of brick work or concrete surfaces of ceiling finsihed fair and even complete all as specified and directed.

Supply only Liquid water proofing compound complete all as specified and directed.

M&L for preparation on new plastered surface of wall, chajja, parapet etc and applying two coats of cement base paint over a coat of acrylic chalk whitening primer etc complete all as specified and as directed.

M&L for preparation of new surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment complete all as specified and directed.

M&L for Providing, plain cement concrete type B0, 1:2:4 (using 12.5mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

S & F ISI marked rotational moulded polyethylene multi- layer water tanks (vertical cylindrical with close top) of 2000 litres capacity hoisted and fixed in position including provision of 25 mm /20 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including dismantling the existing one and removing to store complete all as specified and as directed.

S&F 25 mm dia bore steel tubing medium grade galvanised with all fittings and connection complete all as specified and directed.

S&F 20 mm dia bore steel tubing medium grade galvanised with all fittings and connection complete all as specified and directed.

S&F 15 mm dia bore steel tubing medium grade galvanised with all fittings and connection complete all as specified and directed.

S&F Bib taps of 15mm bore fancy type, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule complete all as specified and directed.

S&F for Gun metal gate valve, 20 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed.

S&F for Gun metal gate valve, 25 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed.

Returning, filling in and including spreading, leveling, watering & well ramming in layers n.exceeding 25 cm in soft/loose soil complete all as specified and directed.

Removing of excavated materials to a distance n. exc 50m and depositing where directed at a level n exc 1.5m above the starting point in oft/loose soil complete all as specified and directed.

Reinforced cement concrete (Design mix) M-25 using 20mm graded aggregate in Beams, lintels over 1.5m span complete all as specified and directed.

M&L for Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 20 mm thick in cement mortar 1:3 and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with admixture of pigment to match the shade of granite stone including grinding and polishing with brass screw complete over 10 mm thick screed complete all as specified and as directed.

M&L for Use and Waste of Formwork (steel plate stiffened with steel angles, steel pipe scaffolding telescopic or otherwise) to the sides of soffits of floor or roof beam, beam haunchings, girders, lintels, cantilever shelves including supports, overhangs, etc and similar ork for flat rough finished surfaces of concrete complete all as specified and as directed..

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410 -W (Gde E- 250) quality A complete all as specified and as directed.

M&L for preparation of painting of new steel surfaces over 10 cm in width or girth over a coat of primer using red oxide and applying two coats of synthetic enamel paint complete all as specified and as directed.

M&L for 75 mm thick Cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base, sub floors etc complete all as specified and as directed..

M&L for or 25 mm thick chequered cement concrete pre-polished tiles of approved size, set, jointed and pointed using with grey cement and pigment in floors, pavings etc including the setting and jointing in neat cement plaster or slurry 0.3 kg/sqm over 20mm thick screed bed or bedding layer in cement mortar (1:6) complete all as per specification.

M&L for machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete all as specified and directed

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc complete all as specified and as directed.

S&F rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc, complete drilled for fixing of steel sheeting or other covering, door etc to be prepared for sliding with and including either hooks and hinges, also fastening and fixing complete all as specified and directed.

E/M PORTION M&L for concealed point wiring for fan/light point controlled by one one way switch complete with 1.5 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red/yellow/blue wires for phases and black wire for neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and including provision of PVC FRLSH insulated 1.5 sq mm copper conductor for earth continuity (Green Colour) and connected to common earth dolly including sunken in GI terminal box 2.8 mm thick bakelite hylam sheet cover, ISI marked with CM/L no. for mounting switch & sockets for the following:- Note : a) Note :- Cost of PVC conduit, cutting chases of wal/ceilingl, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

S&F in repairs epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 4 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as directed.Note: all wire connection with suitable size copper lugs complete all as specified and directed

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning

S&F in repairs MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

S&F Post Top lantern LED type 20 watt 230volt outdoor type with decorative post top for 360degree, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 25000 working hours IP 65 Protection with impact and corrosion resistant suitable for service bracker dia 40mm GI pipe complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as specified and directed.

S&F Post Top lantern LED type 40 watt 230volt outdoor type with decorative post top for 360degree, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 25000 working hours IP 65 Protection with impact and corrosion resistant suitable for service bracker dia 40mm GI pipe complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as specified and directed.

Supply, Laying, testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade of size 2 core 6 sqmm laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including Brass Compression Cable Gland, Terminal Lugs, clamps, nut & bolts etc complete all as specified and directed.

Materials and labour for sand filling around the cable with approved quality coarse sand for sand cushioning of Under ground cable including spreading and punning down to 18 cm thickness complete all as specified and as directed.(Compacted/Punned thickness shall be measured).

M&L for sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and directed.

S&F GI Light grade 40 mm dia of size for road cross/cutting on wall floor drain etc complete all as specified and directed.

S&F CRCA sheet steel duly phosphatized and powder coated with 7 tank process,wall/pole mounted/floor mounted,degree of protection IP 54,pre-wired,liberal terminal space,louvers provided on both sides for proper heat heat dissipation,manufactured by an ISO 9001 certified company, door locking by panel lock and provided for pad locking available,with auto/manual selection switch,astronomical programmable time switch (Operating voltage 220-240 Volt AC), three phase, MCB TPN 40 Amp (coil voltage 240 Volt AC), Power Contactor 32 Amp, Astronomical timer, terminal blocks,maximun load 6KW, complete all as specified and as directed. Make: Havells Cat No.IHXTS0306A or Equivalent make & model of C&S/L&T/ABB

S&F CRCA sheet steel duly phosphatized and powder coated with 7 tank process,wall/pole mounted/floor mounted,degree of protection IP 54,pre-wired,liberal terminal space,louvers provided on both sides for proper heat heat dissipation,manufactured by an ISO 9001 certified company,door locking by panel lock and provided for pad locking available,with auto/manual selection switch, astronomical programmable time switch (Operating voltage 220-240 Volt AC), three phase, MCB TPN 63 Amp, Power Contactor 65 Amp (coil voltage 240 Volt AC), Astronomical timer, terminal blocks, maximun load 12KW complete all as specified and as directed. Make :Havells Cat No.IHXTS0306A or Equivalent make & model of C&S/L&T/ABB

Supply, Laying, testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade of size 4 core 10 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including Brass Compression Cable Gland, Terminal Lugs,clamps,nut & bolts etc complete all as specified and as directed.

Supply, Laying, testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade of size 4 core 16 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including Brass Compression Cable Gland, Terminal Lugs,clamps,nut & bolts etc complete all as specified and as directed.

Supply, Laying, testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade of size 4 core 25 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including Brass Compression Cable Gland, Terminal Lugs,clamps,nut & bolts etc complete all as specified and as directed.

Labour only for Horizontal Boring for Passing Protection Pipe up to 80mm Bore (dia), under Road /Foot Path, not exc. 10.00 mtr in a Single Length, complete all as specified and as directed. Note : Pipe to be measured separately.

M&L for PCC 1:3:6 type C2 (using 40 mm graded aggregate) as in foundation for pole,Cement concrete in foundations, filling and mass concrete etc complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 (using 20 mm graded aggregate) as in coping for pole including form work and finishing the surfaces even and smooth etc complete all as specified and as directed.

S&F 40 mm High density polyethylene pipe (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specified and directed

Material and labour for earthing complete with Galvanised steel earth plate electrode 600x600x6 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI strip of size 32 x 6 mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 40 mm dia GI pipe (light grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protection GI pipe and watering pipe including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of earth lead including protection pipe, from top of earth plate upto 7.5 meter, above/below ground level is deemed to be included in the unit rate. 4. All the joints in earth lead and connection with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate