Military Engineer Services Tender

Supply and fix copper pipe 5/8 inch for aircoditioning suction system cooling and heating including heat resistant covering all as specified

Supply and fix copper pipe 1/2 inch for aircoditioning Delivery system cooling and heating including heat resistant covering all as specified

Supply and fix PVC Drain pipe pipe 1/2 inch for drainout water from Slit AC Unit all as specified

S&F Powerline Vertical TPN DB with suitable for 160A MCCB incomer, double door (IP-54), 4 Ways, built- in 250 Amps copper busbar for each phase, 2 neutral and 2 earth bar complete suitable for 415 Volts, AC, 50 Hz complete all as specified and as directed Make : Legrand (Cat No: 507750)

Supply and fix MCCB, 4 pole, 125 Amps, 415 volts, 50 Hz, 16kA complete all as specified and directed by Engr-in-Charge. Make- Legrand, Siemens, Schinder, Havells.

S&F MCB, SP,240 volts, breaking capacity 10 KA, rating, 'C' curve 40 to 63 amps, complete all as specified and as directed. Make: L&T / Legrand /C&S/Havells

S&F Plug & Socket DB, CRCA Sheet steel, powder coated, with metal plug & socket 3 pin with 32 Amps MCB SPN complete as specified and directed Make : L&T (Cat No: DBMPPS332SD)

S&F Sheet Metal enclosure for SPN DBs, 4 Ways, Double Door, built in 200 Amps bus bar complete suitable for 240 Volts, AC, 50 Hz complete all as specified and as directed Make: L&T / Legrand /C&S/Havells

S&F MCBs, SPN, 240 volts, breaking capacity 10 KA, rating 40-63 amps, complete all as specified and as directed. Make: L&T / Legrand /C&S/Havells

M&L submain wiring with two single core PVC insulated, unsheathed, stranded copper conductor cable (FRLS), 1100 volts grade of size 06 Sqmm (nominal area) each and one single core 06.0 Sqmm (nominal area) as earth continuity conductor drawn into PVC casing capping complete all as specified and directed. NOTE: (i) Rates for PVC casing capping with accessories are deemed to be included in the unit rate.

Excavation in trenches in hard/dense soil not exc 1.5 mtr wide and not exc 1.5 mtr deep in for lying of electric cable, pole foundation and stays etc and getting out, trimming the sides, forming bottom surfaces to required level complete all as specified and directed by Engr-in-charge.

Returning, filling in, including spreading , leveling , watering and well ramming in layer not exceeding 25cm each layer all as specified.

Removing excavated material not exceeding 50M and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified.

Sand cushioning to underground cables provided with a layer of sand 8cm thick before laying the cable in trenches and 15cm thick after laying the cable in trenches complete all as specified.

M&L Sub class ‘B’bricks for covering to cable laid dry flat ,with width equal to the length of brick.

S & F Steel pipe glavanized light grade of 40 mm dia laid in trenches or under ground/floor or road of fixed with pole for protection of cable/ Earth sstrip including clams with bolts nuts and wasers complete ass as specifed.

S&F 80mm dia GI Pipe light grade with all fittings for passing of cables fixed to pole / wall / laid under floor or roads including all fixing accessories complete all as specified and directed by Engr-in-Charge.

Cutting through existing bituminous road /PCC/floor/approx size width 50cm X 60cm depth along cross section of the road for laying of GI tubing/RCC pipe for encasing of cable and repairing the road to match with the original finish, M&L complete all as specified.

Earthing with GI earth plate electrode 600x600x6 mm thick buried directly in ground vertically to depth not less than 2.25m below the ground level with top edge of earth plate at a depth not less than 1.5m below the ground level connected to galvanized iron strip of 32mm x 6mm earth lead by means of bolts & nuts,check nuts & washers made of galvanised steel, earth strip protected by GI Pipe 40mm bore (light grade), including concrete pit using PCC (1:3:6) type C-1,precast RCC (1:1.5:3) type A-1 cover slab with one handle for lifting, funnel with wire mesh, 20mm bore galvanised or steel pipe (light grade) for watering, charcoal & salt in alternative layers including necessary excavation and earth work in any type of soil complete all as shown in electrical plate No. 3 of SSR-2009 Part I all as specified and as directed at site

Earthing complete with galvanized mild steel earth plate electrode size 600x600x6mm thick buried directly in ground (Preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 1.5 meter (BGL) connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 15mm bore “light grade” galvanized iron protection pipe for earth lead wire upto 5m length, charcoal, common salt, complete all as shown in EP No 3 of SSR 2009 part-I, connected to test point complete, all as specified and testing on completion.

Supplying , Laying in trenches XLPE insulated,sheathed, armoured,heavy duty electric power cable with aluminium conductor multy stranded. Suitable for 1100 Volts grade, icluding necessary cable glands and aluminium lugs and having cross sectional area 120 Sqmm 3.5 Core complete all as specified.

Supplying , Laying in trenches XLPE insulated,sheathed, armoured,heavy duty electric power cable with aluminium conductor multy stranded. Suitable for 1100 Volts grade, icluding necessary cable glands and aluminium lugs and having cross sectional area 50 Sqmm 3.5 Core complete all as specified.

Supplying , Laying in trenches XLPE insulated,sheathed, armoured,heavy duty electric power cable with aluminium conductor multy stranded. Suitable for 1100 Volts grade, icluding necessary cable glands and aluminium lugs and having cross sectional area 35 Sqmm 3.5 core complete all as specified.

Supplying , Laying in trenches XLPE insulated,sheathed, armoured,heavy duty electric power cable with aluminium conductor multy stranded. Suitable for 1100 Volts grade, icluding necessary cable glands and aluminium lugs and having cross sectional area 25 Sqmm 3.5 Core complete all as specified.

Supplying , Laying in trenches XLPE insulated,sheathed, armoured,heavy duty electric power cable with aluminium conductor multy stranded. Suitable for 1100 Volts grade, icluding necessary cable glands and aluminium lugs and having cross sectional area 16 Sqmm 4 core complete all as specified.

Supplying , Laying in trenches XLPE insulated,sheathed, armoured,heavy duty electric power cable with aluminium conductor multy stranded. Suitable for 1100 Volts grade, icluding necessary cable glands and aluminium lugs and having cross sectional area 10 Sqmm 4 core complete all as specified.

Supplying , Laying in trenches XLPE insulated,sheathed, armoured,heavy duty electric power cable with aluminium conductor multy stranded. Suitable for 1100 Volts grade, icluding necessary cable glands and aluminium lugs and having cross sectional area 10 Sqmm 2 core complete all as specified.

Supply and fixing in replacement LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. MAKE :- Phillips/wipro/Crompton.

S&F street light bracket made out of GI tubing 40mm bore, medium grade, 1.5 metre long bent to shape as directed, including suitable MS clamp of MS Flat with MS bolts, nuts and washer fixed to steel tubular pole/PCC pole duly painted with two coats of aluminium paint complete including taking down u/s bracket any type all as specified and as directed.

Supply & Fix in replacement of PVC round 3 Core copper cable 1100 volts grade PVC insulated and PVC sheathed of size 1.5 sqmm complete all as specified and directed.

Supply and fixing in replacement of Thermal magnetic release MCCB 4 pole 415 volt rapturing capacity 36 KA 0f size 160 amp complete all as specified.

Supply and fixing in replacement of Thermal magnetic release MCCB 4 pole 415 volt rapturing capacity 36 KA 0f size 200 amp complete all as specified.

Supply, fabricate, erect, connect, test and commissioning of factory made, CPRI approved, cubical type, Outdoor type LT panel board, double door, front and rear opening with locking arrangements, totally enclosed, dust, weather and vermin proof 1100 Volt, 3 phase, 4 wire system, 50 HZ , 415 volt supply made out by 3.15mm thick CRCA sheet for load bearing and 2mm thick for non load bearing, fully compartmentalised, with IP - 65 protection, painted with powder coated paint, and 4 side slanting canopy type roof on top, danger notice board, Suitable size of angle iron padastal frame with nut and bolt (65 x 65 x 6mm) 600mm hight above ground level including PCC work and dismantling of old LT panel and refixing existing cable connection with new cable lugs as per existing all as per conforming to IS-2417 of 1962, complete including the following accessories for each set all as specified and directed. (a) 4 Nos bus bar of equal size made out of copper bus bar of suitable size with PVC insulated coloured heat shrinkable type sleeves, of rating 300 Amps, for looping and branch connection system, mounted on non cracking resin type insulators - 01 Job. all outgoing MCCBs shuld be connected through adiquated size of bus bars. Make of MCCBs from Legrand/ Schneider/ Siemens. (b) TPN, 4 Pole, MCCB ( Thermal magnetic protection) 200 Amps, 415 Volt, 50KA - 01No. (incoming) (c) TPN, 4 Pole, MCCB ( Thermal magnetic protection) 160 Amps, 415 Volt, 50KA - 02No. (Outgoing) (d) TPN, 4 Pole, MCCB ( Thermal magnetic protection) 63 Amps, 415 Volt, 36KA - 03No. (Outgoing) (e) TPN, 4 Pole, 'C' curve MCB 63 Amps, 10 KA - 01No. (Outgoing) (f) TPN, 'C' curve MCB 32 Amps, 10 KA - 01No. (Outgoing) (g) SPN, 'C' curve MCB 32 Amps, 10 KA - 01No. (Outgoing) (h) Indication lamps R, Y & B - 01 Set (i) Provisioning of copper tinned cable glands for incoming and outgoing cables - 01 Job. (j) Provision of 3 phase, 3 display multi functional meter. with CTs and PTs (V, A, W, PF, VA, WH) Legrand 414991 -01 set

Supply, fabricate, erect, connect, test and commissioning of factory made, CPRI approved, cubical type, Outdoor type LT panel board, double door, totally enclosed, dust, weather and vermin proof 1100 Volt, 3 phase, 4 wire system, 50 HZ , 415 volt supply made out by 3.15mm thick CRCA sheet for load bearing and 2mm thick for non load bearing, fully compartmentalised, with IP - 65 protection, painted with powder coated paint, and 4 side slanting canopy type roof on top, danger notice board, Suitable size of angle iron padastal frame with nut and bolt (65 x 65 x 6mm) 600mm hight above ground level including PCC work with new cable lugs as per conforming to IS-2417 of 1962, complete including the following accessories for each set all as specified and directed. (a) 4 Nos bus bar of equal size made out of copper bus bar of suitable size with PVC insulated coloured heat shrinkable type sleeves, of rating 200 Amps, for looping and branch connection system, mounted on non cracking resin type insulators - 01 Job. all outgoing mccb shuld be connected through adiquated size of bus bars. Make of MCCBs from Legrand/ Schneider/ Siemens. (b) TPN, 4 Pole, MCCB ( Thermal magnetic protection) 160 Amps, 415 Volt, 50KA - 01No. (incoming) (c) TPN, 4 Pole, MCCB ( Thermal magnetic protection) 100 Amps, 415 Volt, 50KA - 01No. (Outgoing) (e) TPN, 4 Pole, 'C' curve MCB 63 Amps, 10 KA - 01No. (Outgoing) (f) TPN, 'C' curve MCB 32 Amps, 10 KA - 01No. (Outgoing) (g) SPN, 'C' curve MCB 32 Amps, 10 KA - 01No. (Outgoing) (h) Indication lamps R, Y & B - 01 Set (i) Provisioning of copper tinned cable glands for incoming and outgoing cables - 01 Job. (j) Provision of 3 phase, 3 display multi functional meter. with CTs and PTs (V, A, W, PF, VA, WH) Legrand 414991 -01 set

Supply, fabricate, erect, connect, test and commissioning of factory made, CPRI approved, cubical type, Outdoor type LT panel board, double door, totally enclosed, dust, weather and vermin proof 1100 Volt, 3 phase, 4 wire system, 50 HZ , 415 volt supply made out by 3.15mm thick CRCA sheet for load bearing and 2mm thick for non load bearing, fully compartmentalised, with IP - 65 protection, painted with powder coated paint, and 4 side slanting canopy type roof on top, danger notice board, Suitable size of angle iron padastal frame with nut and bolt (65 x 65 x 6mm) 600mm hight above ground level including PCC work, cable connection with new cable lugs as per conforming to IS-2417 of 1962, complete including the following accessories for each set all as specified and directed. (a) 4 Nos bus bar of equal size made out of copper bus bar of suitable size with PVC insulated coloured heat shrinkable type sleeves, of rating 300 Amps, for looping and branch connection system, mounted on non cracking resin type insulators - 01 Job. all outgoing mccb shuld be connected through adiquated size of bus bars. Make of MCCBs from Legrand/ Schneider/ Siemens. (b) TPN, 4 Pole, MCCB ( Thermal magnetic protection) 200 Amps, 415 Volt, 50KA - 01No. (incoming) (d) TPN, 4 Pole, MCCB ( Thermal magnetic protection) 63 Amps, 415 Volt, 36KA - 03No. (Outgoing) (e) TPN, 4 Pole, 'C' curve MCB 63 Amps, 10 KA - 01No. (Outgoing) (f) TPN, 'C' curve MCB 32 Amps, 10 KA - 01No. (Outgoing) (g) SPN, 'C' curve MCB 32 Amps, 10 KA - 01No. (Outgoing) (h) Indication lamps R, Y & B - 01 Set (i) Provisioning of copper tinned cable glands for incoming and outgoing cables - 01 Job. (j) Provision of 3 phase, 3 display multi functional meter. with CTs and PTs (V, A, W, PF, VA, WH) Legrand 414991 -01 set

Supply, erection, testing and commissioning of outdoor type LT Bus Bar Chamber box in replacement, platform mounted, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos stepped type Aluminium bus bars 400Amps capacity for looping & branch connection system .The chamber shall be painted with powder coated paint. The bus bar chamber shall be provided with suitable Neoprene rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 (a) The bus bar chamber shall be made out of 3.0mm thick CRCA mild steel sheet and 3.00mm thick gland plate , front door (01 layer) and rear Door (01 layer) opening facility and 4 side slanting canopy type roof on top and angle iron padastal frame 600mm high above ground level. The bus bar chamber shall be provided with ventilation facility in the form of louvers for better heat dissipation. (Note : The bus bar chamber Box shall be designed in such a way that adequate workable space is made available inside the compartments and the size of the chamber shall not be less than 600mm height (without base frame & canopy), 500mm width and 400mm depth).

Supply and fix outdoor type pole mounted LT Bus Bar Chamber box, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos stepped type Aluminium bus bars 200Amps capacity for cable connection system including necessary clamps for fixing arrangements .The chamber shall be painted with powder coated paint. The bus bar chamber shall be provided with suitable lockintg arrangements and fixing arrangements in steel tubular pole. (a) The bus bar chamber shall be made out of 2.00 mm thick CRCA mild steel sheet (Note :The bus bar chamber Box shall be designed in such a way that adequate workable space is made available inside the compartments and the size of the chamber shall not be less than 320mm height 400 mm width and 200mm depth).

M & L for junction box hot press moulded SMC of 295 x 195 x 100mm and outside dimention with locking arrangements consisting of necessary suitable arrangements for incoming & out going cables with cable glands & having TPN Bus bar 100A amps capacity with necessary base insulator and including necessary flat iron clamps with nuts, bolts & washers all as specified and directed. Make- Sintex Industries Ltd or equivelent make.

Note: In case doubling/duplicancy of BOQ items , the lowest quoted rate shall be applicable for payment.