Military Engineer Services Tender

(c) SEWAGE TRANSFER PUMPS (Equalization Tank) - Providing and fixing non-clog, open impeller type fully submersible pumps in the existing Collection Pit. The pump shall be complete in CI construction with cutter arrangment including lifting arrangement for the pumps including piping, valves on the discharge of pumps, level controllers, probes, cable, etc. including connection to STP. Sewage transfer pump (2 Nos - 1 working + 1 Standby) Flow Rate (each) = 15 m3 / hr each Head = 10-12 Mtr Solid Handling = 15-20 MM (One No additional pump with flow rate 45 m3/hr at 10-12 m head to be provided for for peak flow.) (d) DRAIN PIT SUMP PUMPS : Providing and fixing non-clog, open impeller type fully submersible pumps in the sump. The pump shall be complete in CI construction with cutter arrangment including lifting arrangement for the pumps including piping, valves on the discharge of pumps, level controllers, probes, cable, etc. including connection to STP. Drain transfer pump (2 Nos - 1 working + 1 Standby) Flow Rate (each) = 10 m3 / hr each Head = 10-12 Mtr Solid Handling = 15-25 MM (e) AIR DISPERSION SYSTEM : Twin Rotatory Air Blower, Head - 5 mtr, Capacity 300 m3 (1W + 1S) @ 0.55Kg/cm2 with Motor driven through "V" belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415 + 10% volts, 3 phase, 50 cycles A/C. - 02 Nos

(f) Provision of Coarse Bubble Diffuser non clog type air dispersion system capable of handling desired cfm of air. Air dispersion system shall be provided for raw sewage equilization tank & sludge holding tank - 16 Nos (g) Provision of Fine Bubble Diffuser non clog type air dispersion system capable of handling desired cfm of air. Air dispersion system shall be provided for the MBBR Reactors - 24 Nos (h) Filter Feed Pumps: Providing and fixing Horizontal centrifugal pumping set for filter feed pumps and discharging into the treated water tank. The pumps shall have CI casing, Bronze impeller - EN 8 shaft shaft with mechanical rotary shaft seal connected by a flexible tier type coupling to a TEFC induction motor mounted on a common channel base-plate with coupling guard,150 mm dia pressure gauge, GM isolation cock, suitable vibration eliminator, pads of approved design. Motor to be suitable for 400/440 V, 3 Phase, 50 cycles AC power supply. Including all necessary piping, valves and other accessories from STP to filteration units and treated water tanks. Filter feed pumps (2 Nos - 1 working + 1 Standby) : Flow Rate (each) = 20 Cum/hr. each Head = 30 Mtrs (j) Sludge Transfer Pumps For Suitable MBBR System : Providing and fixing horizontal, centrifugal sludge lifting pump to transfer sludge from instantaneous sludge storage tank to sludge holding tank.. The pumps shall have CI casing, impeller - shaft with mechanical rotary shaft seal connected by a flexible tier type coupling to a TEFC induction motor mounted on a common channel base-plate with coupling guard,150 mm dia pressure gauge, GM isolation cock, suitable vibration eliminator, pads of approved design. Motor to be suitable for 400/440 V, 3 Phase, 50 cycles AC power supply. Including all necessary piping, valves and other accessories including piping from pump to outside of suitable size 50 mtr. (approx.) length of suitable size to unload the slugde into a tanker as instructed by site-in-charge complete in all respect.

Sludge Recirculation Pump (2 Nos - 1 working + 1 Standby) Flow Rate (each) = 30 Cum/hr. each Head :10-15 mtrs. (for MBBR System) (k) Multi Grade Sand filter: (Suitable for 300 m3/Day) : Providing, fixing, testing & commissioning of vertical Pressure Sand Filter fabricated from MS sheet with epoxy painted as per manufacturer’s specifications with MS frontal piping including valves to provide service, backwash and rinsing operations. Complete with initial charge of filter media including anthracite & bio glassic media. - 01 set Shell Thickness - 8 mm Dish end - 10 mm Filtration Rate -- 18 m3/hr./m2 Test pressure -- 5.5 Kg/Cm2 Capacity 20000-30000 LPH (l) Activated Carbon Filter: (Suitable for 300 m3/Day) : Providing and fixing vertical MS make activated carbon filter with rubber lining of (Iodine value not less than 1000) as filter media. The shell shall be complete with initial charge of filter media MS frontal piping, complete including valve for service, rinse & backwash alongwith other accessories. - 01 set Shell Thickness - 8 mm Dish end - 10 mm Filtration Rate - 15m3/hr/m2 Test Pressure - 5.5 kg/cm2 Capacity -20000-30000 LPH (m) FLOW METER : Supply, installation, testing and commissioning of microprocessor based Electro Magnetic Flow Meter for total plant capacity of 300 KLD with pulsed DC excitation having automatic 'Zero' correction with Bi directional flow measurement, compact instrument version with measuring sensor (Primary) and Amplifier integrated in one mechanical unit. - 02 Nos

(n) PH METER : Providing, installing, testing and commissioning of online digital type pH meter. - 01 No (o) TURBIDITY METER : Providing and fixing turbidity meter. - 01 No (p) MICRO FILTRATION SYSTEM : Supplying, installing, testing and commissioning of MF System piping and  Valves  with all the required accessories, complete in all respects. - 01 set MF Module -Variable Pore Micro Filtration ( 5 micron) filter in SS hosing, Fiber MOC-PE/PP/Nylon, Pneumatic Valve, PLC Electrical Panel and all other accessories making the system complete. Providing, installation, testing & commissioning of Micro Filtration System (MF) of capacity 20 m3/hr. The system should be complete (with Feed Pump 20m3/hr ,MOC: CI (1W+1SB), Back Wash Pump ,40m³/h,Head : - 20-25 m(1W+1SB), Designed by the supplier. complete instrumentation for automation and monitoring Rotameter, pressure guage, interconnecting pipe, vales/solenoid valve, PLC base eleiberctrical panel with cabling all complete with all accessories. Flow rate : 20 cum/hr Output Oprating Pressure- 2-2.5kg/cm2 Backwash method- Air and Water Membrane Type :- Out to in process (q) SLUDGE HANDLING SYSTEM : Supplying, installing, testing and commissioning of filter press with hydraulic arrangement and all accessories as under for sludge handling system for STP of capacity 300 KLD. - 01 set Structure: Cast Iron Size of Plate: 760 mm x 760 mm, No. of plates : 28 Nozzles : P.P. Filter Element (MOC): P.P. Filter Element : Plate & Frame , Drainage surface: P.P. - Piped Delivery : Open, Operating Pressure : 3 bar (max.) , Working temperature : Ambient , Filter Media: P.P./Polyester Nos. 1

(r) SCREW PUMP : Supplying, installing, testing and commissioning of Screw feed pump to feed the Filter Press. Sludeg Feed Pump (02 Nos -1 working + 1 standby) Capacity : 2.5 m3/hr each Head : 40-50 mtrs. (s) All interconnecting pipelines, fittings and isolation control valves for making the system complete. - 01 lot (t) Hypo Dosing Pumps having capacity of 0-6 LPH Metering Type with one dosing Tanks of capacity 500 Lits. -02 Nos (1 W + 1S) (u) Supply, installation, testing & commissioning of Random Media for attached growth process (MBBR Technology) MOC = PVC, Surface Area = 400 sq.mtr / cum.mtr. - 27Cum (v) Supply, installation, testing and commissioning of PVC tube deck settling media to be installed in secondary settling tank . - 12 Cum Note :- (i) Consumables like bio culture for MBBR and Chlorine (Calcium Hypochrorite GP) as required for regular maintenance of plant is deemed to be included in quoted rates for a period of two years and no extra amount will be entertained on this account. List of consumbles shall be recorded and submitted during the claim of RAR. (ii) All test parameter for treated water shall be tested on quaterly basis from any National Test House /IIT/NIT/Zonal Lab/Command Testing Lab/NABL Lab/Govt approved Lab to confirm that parameters of treated sewage water are within specified limits (Ref E-in-C's Branch Sub Dte of Utility (E4) letter No. 86435/Misc/E4(U3) dt 19 May 2023) and the test reports shall be submitted by the contractor till defect liability period.

ELECTRICAL WORKS (a)Supply, installation, testing and commissioning of electrical panel, modular type, front accessible only, free floor standing confirming to Minimum IP:43 degree of protection. The panel sheet structure shall undergo seven tank pre-treatment process before painting. The sheet steel shall be all of 14 SWG/2mm thick CRCA sheet. All the openable compartments of the panel shall be completely shrouded and provided with padlocking arrangement on all compartments including bus bar and cable alley chambers. The panel height shall not exceed 2200 mm and the maximum operating height for any switchgear shall not be more than 1800mm. The panel shall be provided with minimum 75mm base channel frame fabricated from ISMC sections. All bus bar links in the panel shall be solid bus bars with coloured PVC shrinkable sleeves, no wires will be acceptable. Continuos earth bus shall run alround the panel with earthing studs provided at minimum 2 places. The control wiring shall be carried out with minimum 2.5 sq.mm copper wires and adeq for remote operation of the starters. - 01 set All MCCB's shall be provided with rotary handles and minimum fault rating of MCCB shall be as per drawing. Proper sized cable termination gland plates shall be provided on cable alleys and knockouts for same shall be provided during fabrication stage itself. The panel shall be provided with a thermostatically controlled heating arrangement (200W) to take care of high humidity conditions. One 5A socket service outlet (single phase) shall be provided in one of the compartments as service outlet in the panel. Panel shall be so designed at to have minimum 20% spare feeders/space. Panel shall undergo epoxy powder coated paint, colour as per IS:5 requirements. All cable terminations shall be from top. The complete panel shall be fuse less type, for control circuits 2A/6A MCB's to be used.

All bus bars shall be of aluminium, electrolytic grade only. Maximum design density shall not exceed 1Amps./Sqmm. All bus bars shall be insulated with coloured heat shrinkable PVC sleeved. All bus bar supports shall be non hygroscopic DMC/ SML supports. The panel shall be manufactured in conformance to CPRI. The minimum clearances between bus bars shall be as follows: Phase to phase - minimum 20 mm Phase to neutral - minimum 15 mm Incoming One (1) Nos. 63 A, TPN MCCB (35 KA) with over current, over/under voltage & earth fault protection. One (1) No. 0-63A, Digital ammeter with ammeter selector switch & required CTs. One (1) No., 0-500 V, Digital voltmeter with voltmeter selector switch & required set of PTs. One (1) Set Phase Indication Lights with 2A SP MCB. One (1) Set 0-63A Digital KWH Meter. Bus Bars: Set of 04 Nos Aluminium bus bar of 150 Amp, 415V having colour sleeves as RYBN Outgoings: One(1) No. 10A TPN MCB Motor Duty. One (1) No. 16A TPN MCB Motor Duty. Two (2) Nos. Auto/Manual, Working /Standby DOL starter of 3.0 KW rating with SPP, TP MCB, O/L relays, Digital ammeter with direct type/ CT type as per req, ON/OFF/OVER load indication lamps with 6 Am SP MCB provision of space for wlc. Collection Pit Submersible Pump.

Two (2) Nos., Auto/ Manual, Working /Standby DOL starter of 2.2 KW rating with SPP, TP MCB O/L relays, Digital ammeter with direct type/ CT type as per req. ON/OFF/OVER load indication lamps 6 Amp SP MCB provision of space for wlc. Equalization Tank Submersible Pump. Two (2) Nos., Auto/Manual, Working /Standby DOL starter of 5.0 HP rating with SPP, TP MCB O/L relays,Digital ammeter with direct type /CT type as per req. ON/OFF/OVER load indication lamps 6 Amp SP MCB provision of space for wlc. Filter Feed Pump. Two (2) Nos., Auto/Manual, Working /Standby DOL starter of 3.0 HP rating with SPP, TP MCB O/L relays,Digital ammeter with direct type/ CT type as per req. ON/OFF/OVER load indication lamps 6 Amp SP MCB provision of space for wlc. Sludge Transfer Pump. Three (3) Nos., Auto/Manual, Working /Standby DOL starter of 3.0 HP rating with SPP, TP MCB O/L relays,Digital ammeter with direct type/ CT type as per req. ON/OFF/OVER load indication lamps 6 Amp SP MCB provision of space for wlc. Sludge Fees (Screw ) Pump & Filter Press. Two (2) Nos., Auto/Manual/Standby SD With Cyclical Timer of 7.5 HP rating with SPP, TP MCB O/L relays, Digital ammeter with direct type/ CT type as per req. ON/OFF/OVER load indication lamps 6 Amp SP MCB, Air Blower One (1) No., ON/OFF/ Selector Switch.With 6 Amp SP MCB for Dosing Pump. One (1) No., of 1800 W with ON/OFF/Selector Switch With 6 Amp SP MCB for UV System.

(b) Cables and accessories: Design, Supply, Installation, Testing and Commissioning of Copper Conductor Control Armoured Cable/ Aluminium pvc insulated conductor armoured cables including terminations, cable glanding using brass plated single/double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting thesame to the equipment terminals, identification tags etc. complete as per specification or as required. - 01 lot (c) Cable trays & accessories Providing & fixing of cable trays of the required sizes (in one/two/ three tier fashion either on one side of the wall or on two sides of the wall) of GI/MS slotted sheets including grouting supports/hangers required hardwares etc. as specified subjected to the approval of Engr-in-charge. - 01 lot (d) Supply, installing, testing and commissioning of electronic type level controller for filter feed pumps and chlorine contact tank comprising of dry run protection in chlorine contact tank low and high level start and stop complete in all respect (for chlorine contact tank and treated water tank). - 03 sets

SCHEDULE 'A' PART- II ( EARTHWORK AND EXCAVATION) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART- III (INTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents.

SCHEDULE 'A' PART- IV (INTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents.

SCHEDULE 'A' PART- V (ROADS/FOOTPATH) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART- VI ( AREA DRAINAGE) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART- VII ( SEWAGE DISPOSAL) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART- VIII ( EXTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART- IX ( EXTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART- X ( COMPOUND WALL) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART -XI (MISCELLANIOUS ITEMS) Note:- This schedule is not pre-priced by MES.

SITE CLEARENCE Clearance of jungle including cutting of any girth shurbs trunks stumps roots grass weed and nacessary excavation including removal of unserviceable materials to distance exceeding 100 m n exc 150 m complete all as specified.

INTERNAL ELECTRIFICATION S&F supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete complete all as specified and as directed.

Supply and fixing LED lights fitting 4 feet, 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including street light GI pipe bracket of medium grade 40mm dia. ,1.5m long bend to required size and shape including two coat of aluminum paint over a coat of red oxide primer complete in all respect all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 Mtr deep below normal ground level with top edge of plate not less than 1.5 Mtr below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No-3 SSR Part -1 2009 connected to earthing test point including earth wire protection pipe of dia 15 mm (medium grage), excavation and earth work, disposal of surplus spoil, provn of RCC cover 50 mm thick, reinforced with 8mm dia TMT bars @100 mm /C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab and PCC (1:3:6) type C-1 concrete pit, funnel with watering pipe 20 mm bore (light grade) testing on completion complete all as specified and directed. [Note : (a) Proper earthing pit should be provided with pit cover. (b) Excavation/earthwork is deemed to be included in the quoted rate.]

INTERNAL WATER SUPPLY Supplying and fixing 15mm bore angle stop cock high pressure with capstan head long shank screwed down complete all as specified and directed.

SEWAGE DISPOSAL Supply and fix heavy duty UPVC pipe (column) 100 mm dia. along with column pipe socket of 3.0m length including all necessary fittings complete all as specified and directed.

M&L for PVC insulated submersible flat cable 16sqmm 3 core with copper conductor complete all as specified and directed

Material labour for automatic star delta starter capacity upto 10 HP, relay range (14 - 20 Amp) with hour meter, incorporting heavy duty 4 pole contractor type TCID, overload relay type LR-3D, auto start switch, 3 position selector switch for SPP, auto SPP manual/ manual dual analog VA meter, 3 Phase KWh meter (2 Motor SPCU power on hours), RYBLED indicator motor on and trip, LED indicator TPC curve MCB for short circuit protection fixed in position when directed with the help of MS febricated bracket angals nut bolts etc. complete all as specified and directed.

Supply, installing, testing and commissioning of Non clogging submersible sewage pump capacity 7.5 HP delivery pipe size 80mm (3 Phase, 415 V 50Hz) alongwith all accessories for pumping out sewage from the underground sump complete all as specified and directed.

Supply and laying of Centrifugally cast (spun) Ductile iron pressure pipes with spigot & socket end of 150mm bore, Class K-7, conforming to IS-8329/2000 (latest revision) suitable for (push on) rubber gasket jointing with centrifugally applied inside cement mortar lining with sulphar resistant cement and external metallic zinc coating with a finishing layer of black bitumen coating on external surface suitable for sewage water supply and including rubber gasket joint in any lenght laid in trenches complete all as specified and directed.

S&F factory made precast RCPC manholes covers of clear internal dia. 600mm, ST load capacity, confirming to IS 12592:2002 placed/ fixed in position complete all as specified and as directed

Cleaning of existing sewage lines of dia 100mm to 250mm at depth of 1m to 5m from existing ground level with mechanically operated cleaning / root cutting equipment including removal of all kinds of blockages/ chockages in the sewage lines for free flow of sewage including removal sludge from the manholes/lines and disposing off the same out side MD land complete all as specifiede and as directed.

M&L for boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine for DI/HDPE pipe of 150mm dia. without distrubing the road surface / pavment surface/ hard standing /RCC surface for laying of PPR/HDPE pipe of max size 150 mm bore complete all as specified and directed

EXTERNAL WATER SUPPLY Supply, Installing testing and commissioning of mono block centrifugal pump set suitable for 415 volt TPN system having capacity 10 HP for treated water distribution complete all as specified and directed.

Material labour for automatic star delta starter capacity 10 HP, relay range (14 - 20 Amp) with hour meter, incorporting heavy duty 4 pole contractor type TC1D, overload relay type LR-3D, auto start switch, 3 position selector switch for SPP, auto SPP manual/ manual dual analog VA meter, hour meter (2 Motor SPCU power on hours), RYB LED indicator motor on and trip, LED indicator TPC curve MCB for short circuit protection fixed in position when directed with the help of MS febricated bracket angals nut bolts etc. complete all as specified and directed.

M & L for construction of brick masonry valve pit of size 120 x 120 x 90 cm (internal dimensions) with one brick thick wall in cement mortar 1 : 4 on 100 mm thick PCC 1:4:8 D2 (using 40 mm graded broken stone aggregate) as in foundation lean concrete, incl. PCC 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) as in bedding and coping and 10 mm thick cement plaster in CM (1:4) internally and externally upto 15 cm below ground level providing valve pit 40 X 40 X 6 mm angle iron frame all round the fixed point by means of 04 Nos holdfast 150 mm long made out of flat iron 40 X 6 mm embedded in PCC block (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) of size 250 X 200 X 150 mm incl. provision of hinges welded with MS cover 3 mm thick, MS handle of suitable and size welded with MS cover and suitable locking arrangement incl. 65 mm dia with pad lock and applying two coats synthetic enamel paint over a coat of red oxide primer incl. necessary excavation and earth work in soft/loose soil complete all as specified and directed.

External Electrification Supply, Install, testing and commissioning of distribution transformer capacity 100 KVA step down outdoor type floor mounting. copper wound complete with standard fittings HT 11 KV 3 Phase, LT 433 Volts, 3 Phase 4 Wire, Oil immersed with ‘ONAN' type cooling with external cooling tubes/ radiators having no load voltage ratio 11/433 KV connected on secondary side (Secondary outgoing side) in accordance with vector group symbol (DYN-11) conforming to IS-1180 (Part-I) : 2014, Level-I as per latest 4th amendment in March 2021, and having off load tap changer in step of 2.5% on HV side to take care of voltage from +7.5%, + 5% to +2.5% to give output on 433 Volts secondary side and including initial oil filling to appropriate level, control cable and following standard fitting complete all as specified and as directed. (a) Oil Conservator with oil fitting hole cap and drain plug. (b) 01 No of prismatic oil level gauge mounted on conservator wall with first fill of charge upto maximum level. (c) Silica gel dehydrating breather with oil seal and first fill of charge. (d) Pressure release valve with automatic resetting arrangement after release of preassure. (e) Adequate No of thermometer pocket including one thermometer. (f) Top oil filter valve. (g) Bootom oil filter cum drain valve. (h) Rating diagram and terminal marking plate. (j) Earthing terminal - 02 Nos (k) Lifting Lugs - 01 Set (I) Jacking Pads - 01 Set (m) Under carriage with 4 Nos of plain rollers (n) Air release plug on main transformer tank. (o) Adequate Nos of cooling radiators.

(p}100mm Dial type oil temperature indicator with maximum red pointer and resetting device. (q) 100 mm dial type winding temperature indicator with maximum red pointer and resetting device. (r) Air insulated cable box on HV and LV side. Note: (i) Routine test shall be carried out as per IS 1180. (ii) Pre-dispatch inspection at OEM premises shall be carried out by the tep of accepting officer. (iii) After successful installation and commissioning , contractor shall get TFR tested by SEI/EI prior to pre-commissioning.

Supply & installation of silent Diesel Engine driven generating Set 415 Volts, 3 Ph 4 wire, engine as per IS : 10001/10002 and alternator as per IS :60034 complete with relay panel for automatic starting on mains failure, control panel having meters, sound proof canopy and foundation etc. of capacity 62.5 KVA 4 Stroke, designed to run continuously at 1500 RPM complete with the following accessories:- (A) Diesel Engine:- (i) Radiator cooling (ii) Radiator fan with guard (iii) Fly wheel with starter ring (iv) Dry type air cleaner (v) Vacuum indicator (vi) Mechanical governor (vii) Exhaust Silencer (viii) Fuel filter (ix) Inline fuel pump (x) Water pump (xii) Lub oil Filter (xiii) 24 V electric start system complete with starter ,battery charging alternator (xiv) Engine control panel consisting of starting key switch ,lub oil pressure gauge , ammeter safety shut down system for low lube oil pressure and coolant temperature engine maintenance manual with spare parts list. (xv) Exhaust pipe /stack upto 6m from top of shed with insulation structural steel required for supporting exhaust pipe/stack, fixed supports, sliding supports etc. (xvi) First fill of lube oil and coolant. (xvii) Residential silencer with cladding & supports

(B) Alternator Alternator conforming to IS-60034 with standard design with IP 23 protection ,suitably rated at 50KW/62.5KVA at 0.8 PF,415 volts,3-phase,4wires,50 Hz,1500 RPM, self excited brushless excavation) and self regulated, band of voltage regulation +/- 1.5% of rated voltage ( from no load to full load) and class "H" insulation, alternator should be mounted on common single base frame and coupled directly to the engine (C) Acoustic Enclosure Acoustic enclose as per norms of central pollution control board (CPCB) issued by ministry of environment & forests, Govt. of India (D) control panel cum AMF panel: The panel is equipped with as follows:- (i)Suitable size of MCCB FP - 02 Nos (ii) Digital ammeter with selector switch-01 No (iii) Digital voltmeter with selector switch -01 No (iv) Digital frequency meter -01 No (v) Instrument fuses & control wiring (vi) Pilot lamp for ' Load on' and ' Set running' (vii) Incoming & outgoing terminals (viii) AFM control accessories with contract of suitable size ,microprocessor based relay & wiring etc-01 No (ix) Over load protection system with relay -01 No (x) Electronic type 3 phase multi function meter-01 No (E) Spare parts & tools: (i) Rotary pump diesel with 3 mtr hose-01 set (ii) Box spanner set complete with all sizes

(iii) Oil filter set 2 Nos (iv) Air filter complete with element-02 nos (v) Fuel filter set -02 Nos (vi) AVR-01 No (vii) Rubber matting size 0.9mt*1.5 mtr* 15mm thick -02 Nos Note : (i) PCC foundation of adequate /required size extending 500mm all round more than size of DG set, as per manufacturer design. (ii) DG set shall be tested as type test routine test as per IS in presence of GE/his rep. (iv) The contractor shall get approval of GE for the make of DG set they plan to procure (v) Prior manufacturing the general arrangement drawings design details of the DG set and AMF panel shall be got approved by GE (vi) After installation of DG set at site, the pre commissioning test shall be carried out by IEM/Rep of Accepting Officer and the cost of consumable such as oil, DHPP'N', T&P deemed to be included in the quoted rate.

Supply and installation, testing and commissioning Outdoor type 20 KVAR capacity APFC bank panel, MDXL offered Heavy duty Mixed dielectric type Box capacitor with 7 % Aluminum wound Reactor, units tested in accordance with IS 13340-1993/IS 13341-1992, IEC 60831 part 1 & 2 with thyristor control module with aluminium heat sink with semiconductor fuses, smooth switching On and Off automatically at +/- 10 Volts, compartmental design dust and vermin proof suitable for 3 phase, 4 wire 440 volt, made out of 3.15mm thick CRCA sheet with built upon rigid frame work, cubical type, heavy duty powder coated RAL 7035 capacity 20 KVAR (10x1+5x2) kVAr capacitor bank having following accessories including control wiring with HR FR/FRLS copper wire complete all as specified and as follows :- (i) To withstand on Non Liner load upto 20% (ii) 2.5 in Over Current with stand. (iii) 10000/year Switching capacity. (iv) 1,60,000 hours life expectancy. (v) Capacitor, MCB/MCCB, Contractors, APFC Relay will be of same make. (vi) Panel fabrication need to be in house and at component manufactures own factory. (vii) APFC design with Aluminium bus bar as per global standard current density of 0.8A/Sqmm, (1A/Sq mm in case of copper)

(viii) Ambient will be of 45*C (ix) Ventilation air within cubicle must flow upwards. (x) Extractor fan must be fitted on top of cubicle. (xi) Bottom air intel should be as low as possible. (xii) Cross section of top air outlet must be more than bottom outlet. (xiii) Reactor must be fitted in separate enclusure of capacitor. (xiv) APFC relay with RS485 communication, Dual setting for EB & DG load , to monitor KVAR de rating, inbuilt programmable alarm for capacitor dating, Harmonic Monitoring 3rd to 19th, Temperature alarm and with Fan control relay. (xv) Compact modular bolted design, removable side and back panels with bottom cable entry.

S&F MCCB 4 pole 63 Amps, 50Hz, 415V with rupturing capacity of 25kA complete all as specified and directed

S&F LT pannel frame CPRI approved, Outdoor type, factory made febircated to CRCA sheet of 3.15 mm thickness, angle iron and tee section (frame) of suitable size of 900x600x400mm double door front/rear opening and locking arrangement, floor mounted on plateform of suitable size bus bar chember (enclosed) incl rust free spray painting with two coat of synthetic enamel paint over a coat of red oxide primer mounted on PCC blocks, dixed with grouted bold, nuts and washer and making complete connection in all recpects as directed comprising of following parts, (a) MCCB 4 Pole 415 volts, 125 Amps 35 KA 01 No ( for incoming) (b) MCCB 3 Pole 415 volts, 63 Amps 35 KA for out going :- 01 No ( for outgoing) (c) MCCB 3 Pole 415 volts, 32 Amps 16 KA for out going :- 02 No ( for outgoing) (d) Change over open execution 125 Amps- 01 No (e) Indicator lamp R,Y,B - 01 Set (f) Digital multifunctional meter -01 No (g) Phase selector (Vertical) with rotary switches - 01 Set (h) Astronomical Time Switch 32 Amps 24 hour programming type with ML-4 contractor 70A, 415 V, three phae, coil operating voltage 230 V, three point Auto manual switch 25 Amps for bypass system with 32A 4P MCCB adjustable (40% to 100%) Microprocessor release, 25KA complete including necessary connection.

Supply and fixing LED street light fitting 45 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete all as specified and directed.

Supply and fixing bracket for street light fitting of any size made out of GI pipe medium grade 40 mm dia, 1.5 mtr length bend to required size and shape including provisiob of clamps and fitting in position and including two coat of aluminum paint over a coat of red oxide primer complete all as specified and directed.

Supply and fix Thermo plastic terminal box of size not less than 130 x180 x 77 mm mm with locking arrangement and necessary mounting arrangement on pole with MS clamps, nut bolt and washers etc including 01 No MCB 6 Amps and PVC connector 3 phase and neutral for cable termination complete all as specified and directed.

M&L earthing complete with copper earth plate electrode 600mm x 600mm x 3 mm thick burried directly in ground (Earth pit not less than 3.0 m deep below ground level) with top edge of the plate not less than 2.25m below ground level connected to copper strip 20 x 3 mm as earth lead by brass nut bolts washer including brazing the copper strip with copper plate as shown in electrical plate No 3 connected to earth test point including necessary excavation in any type of soil(except rock), filling charcoal and salt around the plate in layers , filling the pit with agriculture soil free from stones, to be bring from outside defence land, and to be mixed with and including bentonite - 03 bags of 25 KG each for each pit, construction of PCC earth pit chamber of size 900 x 900 x 450 mm , RCC chamber cover plate, wire mess, funnel, test point, 32 mm dia GI protection pipe light grade and 40 mm GI medium grade peforated pipe for watering etc complete and testing on completion. The electrode and lead shall be of copper all as specified and directed. (Note : (i) Fresh agriculture soil will be used for filling the dug as required to achieve the desired resistance from out side (ii) Contractor has to provide bentonite -03 Bags ( each bags of 25 KG) to mix with fresh agriculture soil in each earth pit to achive desired resitance. (iii) Copper strip will be laid below 100mm from ground level and connected to test point through plinth protection.

(iv) Necessary cost of repair to plinth protection and connected plate and earth continuity conductor through double nut bolt and brazing of joints, argiculture soil to be bring from out side deemed to be included in the item rate. (v) Copper strip upto 7.5 RM will be included in the item rate and copper strip beyond 7.5 RM will be measured seperately. (vi) Contractor has to clear the site and disposed of the excavated soil (obtained from the pit ) from the site at the location as directed by Engineer in charge. (vii) Earth test point to be made inside earth pit by providing joint between downward conductor/strip coming from ground to earth continuity strip going to LT Panel.

ABORICULTURE Supply and plantation of Korean grass including preparation, of ground to required depth and filling of sweet earth, cow dung and watering etc complete all as sepcified and directed by the Engineer-in-charge.

Supply and plantation of Ashoka plants(height of plant not less than 45 cm above ground level) including preparation of ground upto 60 cm deep and filling of sweet earth, cow dung, vermi compost and watering etc. complete all as specifed and directed by Engineer-in-charge.

Supply and plantation of Bouganavilia including preparation of ground upto 3.0 cm deep and filling of sweet earth, cow dung, vermi compost and watering etc complete all as specified and directed by Engineer-in-Charge.

Supply and plantation of crotons and hedges including preparation of ground to required depth and filling of sweet earth, cow dung and watering etc. complete all as specified and directed by Engineer-in-Charge.

S&F GI tubes (medium grade) 25mm dia galvanized with all fittings and fixed to walls and ceilings or laid in floor complete all as specified and directed by Engineer-in-Charge.

S&F GI tubes (medium grade) 20mm dia galvanized with all fittings and fixed to walls and ceilings or laid in floor complete all as specified and directed by Engineer-in-Charge.

S&F 20mm dia (3/4 inches) sprinkler with fittings complete all as specified and directed by Engineer-in-Charge.

Maintenance of the plants and grass planted vide item given above by weedings, hosing, saucer moulding once in every 15 days, planting new plants/grass in placed of dead plants/grass of same species and height with out any extra cost to the department and as directed by Engineer-in-Charge complete for the period of maintenance period of one year.

AMC AMC by OEM of STP including maintenance of different types of pumps, blower, filters, pipes and valves, MBBR media, tube settler media, carbon media, dual filter media, LT panel board, connecting cable including all types of major and minor repair of any defective parts, periodic cleaning (fortnightly) , scheduled maintenance of running equipments, attending to the emergency break down of the components, regular testing of plant equipments by 'Walk Down' checks of internal conditions of equipments such as plant performance, pump test, decomposition system testing, etc. careful logging of Operational Data and periodically processing it to determine any abnormal or slowly deterioating conditions, careful control and supervision of operational conditions including all consumables and spare parts for maintenance of plant complete all as specified and directed from the next date of completion of Defect Liability Period. Any defective equipments parts of STP Plant shall be replaced without any extra cost. Note : - (i) The AMC of 1st year of maintenance will start by the next day after completion of Defect liability period. (ii) All the other items/parts which are not mentioned in the item, if required necessary for smooth functioning of STP Plant shall be deemed to be included in the rate quoted. (iii) All test parameters for treated water shall be tested on quarterly basis from any National Test House/IIT/NIT/Zonal Lab./Command testing Lab/NABL Lab/Govt approved Lab to confirm that parameters of treated sewage water are within specified limits and the test reports shall be submitted by the contractor with the interim payment bill due at the time of such testing.

(iv) Outsourcing of services of Maint & Operation shall be done through OEM/their authorized service agency. (v) All consumables like bioculture, chlorine, calcium hypo chloride 65-70% and alum etc as required for regular maint of plant is deemed to be included in quoted rates and no extra amount entertained on this account. List of consumables shall be recorded and submitted during the claim of RAR.

AMC by OEM of STP including maintenance of different types of pumps, blower, filters, pipes and valves, MBBR media, tube settler media, carbon media, dual filter media, LT panel board, connecting cable including all types of major and minor repair of any defective parts, periodic cleaning (fortnightly) , scheduled maintenance of running equipments, attending to the emergency break down of the components, regular testing of plant equipments by 'Walk Down' checks of internal conditions of equipments such as plant performance, pump test, decomposition system testing, etc. careful logging of Operational Data and periodically processing it to determine any abnormal or slowly deterioating conditions, careful control and supervision of operational conditions including all consumables and spare parts for maintenance of plant complete all as specified and directed from the next date of completion of Defect Liability Period. Any defective equipments parts of STP Plant shall be replaced without any extra cost. Note : - (i) The AMC of 2nd year of maintenance will start by the next day after completion of AMC of 1st year. (ii) All the other items/parts which are not mentioned in the item, if required necessary for smooth functioning of STP Plant shall be deemed to be included in the rate quoted. (iii) All test parameters for treated water shall be tested on quarterly basis from any National Test House/IIT/NIT/Zonal Lab./Command testing Lab/NABL Lab/Govt approved Lab to confirm that parameters of treated sewage water are within specified limits and the test reports shall be submitted by the contractor with the interim payment bill due at the time of such testing.

(iv) Outsourcing of services of Maint & Operation shall be done through OEM/their authorized service agency. (v) All consumables like boiculture, chlorine, calcium hypo chloride 65-70% and alum etc as required for regular maint of plant is deemed to be included in quoted rates and no extra amount entertained on this account. List of consumables shall be recorded and submitted during the claim of RAR.

AMC by OEM of STP including maintenance of different types of pumps, blower, filters, pipes and valves, MBBR media, tube settler media, carbon media, dual filter media, LT panel board, connecting cable including all types of major and minor repair of any defective parts, periodic cleaning (fortnightly) , scheduled maintenance of running equipments, attending to the emergency break down of the components, regular testing of plant equipments by 'Walk Down' checks of internal conditions of equipments such as plant performance, pump test, decomposition system testing, etc. careful logging of Operational Data and periodically processing it to determine any abnormal or slowly deterioating conditions, careful control and supervision of operational conditions including all consumables and spare parts for maintenance of plant complete all as specified and directed from the next date of completion of Defect Liability Period. Any defective equipments parts of STP Plant shall be replaced without any extra cost. Note : - (i) The AMC of 3rd year of maintenance will start by the next day after completion of AMC of 2nd year. (ii) All the other items/parts which are not mentioned in the item, if required necessary for smooth functioning of STP Plant shall be deemed to be included in the rate quoted. (iii) All test parameters for treated water shall be tested on quarterly basis from any National Test House/IIT/NIT/Zonal Lab./Command testing Lab/NABL Lab/Govt approved Lab to confirm that parameters of treated sewage water are within specified limits and the test reports shall be submitted by the contractor with the interim payment bill due at the time of such testing.

(iv) Outsourcing of services of Maint & Operation shall be done through OEM/their authorized service agency and paid separately. (v) All consumables like boiculture, chlorine, calcium hypo chloride 65-70% and alum etc as required for regular maint of plant is deemed to be included in quoted rates and no extra amount entertained on this account. List of consumables shall be recorded and submitted during the claim of RAR.

Manning & Operation Outsourcing of services for manning and operation of Sewage Treatment Plant round the clock in one shifts (of 08 hrs duration each) per day including Sunday and holiday with one skilled operator and One semiskilled for trouble free operation to ensure maximum optimisation of plant including monitoring the performance of the treated sewage by data logging, monthly report preparation and reporting to MES on performance of Sewage Treatment, Note:- (i) The quoted rates of bidders shall be deemed to be inclusive of the following aspects as below and nothing extra shall be paid on this account. (a) Generation and submission of reports in soft/ hard copy format as required by the Engineer-in-Charge. (b) Area cleaning and removing of grasses, bushes etc. as per instructions of the Engr-in-Charge. (c) Safety and security of all equipments, chambers, T&P, substation complete. (d) Sufficient trained manpower as per OEM or routine schedule/break down maintenance of all Plant equipment, HT/LT control system etc.

(ii) The operators and helper as per OEM's instruction for proper maintainance of the Sewage Treatment system working for 08 hrs shall constitute one shift and the quoted rate of the contractor shall be deemed to be inclusive of this aspect. (iv) Safety chart, First Aid chart and First Aid kit will be provided by contractor and the quoted rate of the contractor shall deemed to be included of this aspect.

All as per Ser item No 49.00 to 49.01 here-in-before but for the period commencing from the next day after completion of Srl Item No 49.00 to 49.01 above.

All as per Ser item No 49.00 to 49.01 here-in-before but for the period commencing from the next day after completion of Srl Item No 50.00 above.

All as per Ser item No 49.00 to 49.01 here-in-before but for the period commencing from the next day after completion of Srl Item No 51.00 above.

All as per Ser item No 49.00 to 49.01 here-in-before but for the period commencing from the next day after completion of Srl Item No 52.00 above.