Military Engineer Services Tender

All as per BOQ Item No 3.00 here-in-before but of size 3.5 core 120 sqmm. ,complete all as specified

All as per BOQ Item No 3.00 here-in-before but of size 3.5 core 95 sqmm. ,complete all as specified

All as per BOQ Item No 3.00 here-in-before but of size 3.5 core 70 sqmm. ,complete all as specified

All as per BOQ Item No 3.00 here-in-before but of size 3.5 core 50 sqmm. ,complete all as specified

All as per BOQ Item No 3.00 here-in-before but of size 3.5 core 25 sqmm. ,complete all as specified

All as per BOQ Item No 3.00 here-in-before but of size 4.0 core 16 sqmm. ,complete all as specified

All as per BOQ Item No 3.00 here-in-before but of size 4.0 core 10 sqmm. ,complete all as specified

Laying only and connecting XLPE sheathed,PVC insulated screened steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade of size 3.5 core 95 sqmm to 150 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including Brass Compression Cable Gland, Terminal Lugs,clamps,nut & bolts etc all as specified

All as per BOQ Item No 11.00 here-in-before but of size 35-70 sqmm, 3.5 core ,complete all as specified

All as per BOQ Item No 11.00 here-in-before but of size 10-25 sqmm, 2 to 4 core ,complete all as specified

Materials and labour for sand filling around the cable with approved quality coarse sand for sand cushioning of Under ground cable including spreading and punning down to 18 cm thickness complete all as specified and as directed.(Compacted thickness shall be measured)

Supply and laying fly ash best quality, laid in trenches, perpandicular to U/G cable for cable protection complete all as specified.

Laying only old bricks obtained from item No 02 perpandicular to U/G cable for cable protection complete all as specified.

Returning, filling in, of soil including spreading leveling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed .

Removing excavated material to a distance n.exc 50M and deposited/ spreaded where directed at a level n. exc 1.5 M above the starting point complete all as specified and as directed .

M & L for Boring of horizontal hole under road, pavement, hardstanding suitable for passing through up to 80 mm bore, complete all as specified. Note : (i) One run of boring of horizontal hole will be measured as one unit length. (ii) All the precaution to be taken by the contractor before drilling the bore. The contractor has to take plan of existing cables any type and pipe line in existing area before drilling the bore. (iii) Any damage to existing cables any type and pipe line in the way of drilling the bore will be repaired and make good by the contractor. No extra cost will be paid on this account. (iv) Contractor has to get the survey of route, length and depth for boring before quoting the rate.

Supplying and fixing Galvanised mild steel pipe /tubing, light grade complete with all fittings of 100 mm bore dia, laid in trenches / under roads, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers as in cable protection complete all as specified and directed.

Supplying and fixing Galvanised mild steel pipe /tubing, light grade complete with all fittings of 80 mm bore dia, laid in trenches / under roads, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers as in cable protection complete all as specified and directed.

Supplying and fixing Galvanised mild steel pipe /tubing, light grade complete with all fittings of 50 mm bore dia, laid in trenches / under roads, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers as in cable protection complete all as specified and directed.

Supplying and fixing High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 complete with all fittings of 25 mm bore dia, laid in trenches / under roads, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers as in cable protection complete all as specified and directed.

Supplying and fixing High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 complete with all fittings of 40 mm bore dia, laid in trenches / under roads, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers as in cable protection complete all as specified and directed.

Supplying and fixing High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 complete with all fittings of 50 mm bore dia, laid in trenches / under roads, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers as in cable protection complete all as specified and directed.

Supplying and fixing High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 complete with all fittings of 100 mm bore dia, laid in trenches / under roads, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers as in cable protection complete all as specified and directed.

M&L for straight through joint (heat shrinkable) complete suitable for LT 1100 Volt aluminium conductor cable of size3.5/4 x 10-16 sqmm and testing after jointing of following sizes of cables. Note Payment will be released only after submission of PV anf test certificate

M&L for straight through joint (heat shrinkable) complete suitable for LT 1100 Volt aluminium conductor cable of size3.5/4 x 25-50 sqmm and testing after jointing of following sizes of cables, Note Payment will be released only after submission of PV anf test certificate

M&L for straight through joint (heat shrinkable) complete suitable for LT 1100 Volt aluminium conductor cable of size3.5 x 70-150 sqmm and testing after jointing of following sizes of cables. Note Payment will be released only after submission of PV anf test certificate

M&L for straight through joint (heat shrinkable) complete suitable for LT 1100 Volt aluminium conductor cable of size3.5 x 185-240 sqmm and testing after jointing of following sizes of cables. Note Payment will be released only after submission of PV anf test certificate

Material and labour for steel tubular poles complete with cast iron base palate, final taper plug bolts, nuts & screws as specified type 410 SP-22. 8.5 meter long including painting all external exposed steel surfaces with two coats of aliminium paint over a coat of red oxide zinc chrome primer and all internal surfaces and external surfaces in contact with concrete with two coats of black bitumenous paint complete all as specified and as directed including taking down old existing concrete poles / struts any size after demolition of foundation and depositing / stackingat a place where directed within 5kM distance from the work site complete allas directed.The remaining external position shall be painted with two coat of aluminium paint including numbering to pole complete all as specified and as directed by Engr-in-Charge. (Note:- Earth work, PCC work, shall be measured and paid separately.)

M&L for cement concrete ( 1:3:6) type C-2 using 40mm graded crushed stone aggregate as in pole foundation, filling and mass concrete complete all as specified

M&L for cement concrete ( 1:2:4) type B-1 using 20mm graded crushed stone aggregate as in coping of pole including weathering, slightly rounded or chamfered angles and throating, necessary formwork as directed complete all as specified

M & L for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections includings nuts, bolts, washers, welding, bending cold or hot drilling holes for bolts, in any shape of size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of aluminium paint including preparation of surfaces complete all as specified and directed

M & L Painting of steel pole (swan neck type or straight type) up to 12 mtr height with cross arms, clamp of any length and shape for LT overhead line/ for street light with two coat of aluminium paint after scraching out old paint, cleaning and exiting surface rust free, preparation of the existing surface, including marking pole numbers in a 15 cm dia yellow circle with number writting with black syenthic paint/ Stricker, including painting strips in alternate from bottom to top with three strips of black syenthatic paint & two strips of Yellow/ Sky blue paint (as per existing pattern through out the circumference of pole, including removing extra wall papdi ,peel off wall papdi by sand paper and making good with putty as per existing thickness and applying one coat of white washing on PCC copping of pole and re-numbering of pole with approved size of letter ( Example - P- 001) with synthetic enamel paint of white colour background and black colour lettering complete all as specified and as directed.

Material and labour for earthing complete with Galvanised steel earth plate electrode 600x600x6 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI strip 32x6 mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 40 mm dia GI pipe (light grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protectionh GI pipe of 40mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI strip of 32x6mm including protection pipe, from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI strip and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate

M&L for preparation of existing surface of LT Panel by srapping down peeled off old paint, cleaning etc of size upto 900mm X 400mm X 900mm (L X W X H) and applying Two coat of Siemens Grey Paint by using spray machine and Black paint on Angle Iron over a coat of red oxide primer complete all as specified and directed by Engr in Charge. Note:- Only external portion shall be painted.

M&L for preparation of existing surface of LT Panel by srapping down peeled off old paint, cleaning etc of size upto 1000mm X 400mm X 1000mm (L X W X H) and applying Two coat of Siemens Grey Paint by using spray machine and Black paint on Angle Iron over a coat of red oxide primer complete all as specified and directed by Engr in Charge. Note:- Only external portion shall be painted.

M&L for preparation of existing surface of LT Panel by srapping down peeled off old paint, cleaning etc of size upto 1200mm X 400mm X 1200mm (L X W X H) and applying Two coat of Siemens Grey Paint by using spray machine and Black paint on Angle Iron over a coat of red oxide primer complete all as specified and directed by Engr in Charge. Note:- Only external portion shall be painted.

S & F in replacement Aluminium Busbars electrolytic grade of as per site required Amps and KA rating, bus bars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in a dedicated compartment. the size and thickness of busbars shall be as per sample including drilling , cutting and suitable size of galvanised or codmium plated high tensile nuts, bolts and washers etc complete all as specified and directed.

S & F in repairs earth continuity conductor or main earthing lead fixed to wall or battens or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other situation using 32 x 6mm GI stripcomplete.

Dismantling existing LT panels of any type, any size carefully for reuse including necessary excavation demolition of concrete,disconnecting of earthing,cable, taking out burn out lugs,MCCBs,bus bars,insulators and other connected works ,surface levelling etc. and reinstall the LT panels after repair/replacement of burn out lugs,MCCBs,bus bars,insulators, wiring etc including re-connection of earthing,cables with new foundation of panels, brick works,PCC works etc complete including testing all as specified and as directed by Engr-in-charge.(NOTE : Earth Work,brick works, foundation work, PCC, lugs, switch gear, metering devices, bus bar,insulators, cable for wiring etc will be Measured and Paid separately under relevant Items as supply only).

Labour only for disconnecting, isolating and taking out burned/unserviceable lugs, switchgear, metering devices, wiring, bus bar etc from any type of pannel/board and replacing the same with new ones including testing completee al as directed by Engr-in-Charge. Note (i): New parts will be measured and paid separately under respective items as supply only. (ii). The item will not be operated simultaniously alongwith the item No 43.00

Supply only the followings ( to be incorporated against Item No 43.00 and 44.00 only)

MCCB 63 Amps rating, 4 pole , 415 V, AC, 50 HZ, adjustable thermal & adjustable magnetic setting setting, Ics-100 % Icu , service breaking capacity 16 KA.

MCCB 100 Amps rating, 4 pole , 415 V, AC, 50 HZ, adjustable thermal & adjustable magnetic setting setting, Ics-100 % Icu , service breaking capacity 16 KA

MCCB 125 Amps rating, 4 pole , 415 V, AC, 50 HZ, adjustable thermal & adjustable magnetic setting setting, Ics-100 % Icu , service breaking capacity 16 KA.

MCCB 160 Amps rating, 4 pole , 415 V, AC, 50 HZ, adjustable thermal & adjustable magnetic setting setting, Ics-100 % Icu , service breaking capacity 36 KA.

MCCB 200 Amps rating, 4 pole , 415 V, AC, 50 HZ, adjustable thermal & adjustable magnetic setting setting, Ics-100 % Icu , service breaking capacity 36 KA.

MCCB 250 Amps rating, 4 pole , 415 V, AC, 50 HZ, adjustable thermal & adjustable magnetic setting setting, Ics-100 % Icu , service breaking capacity 36 KA

MCCB 350 Amps rating, 4 pole , 415 V, AC, 50 HZ, adjustable thermal & adjustable magnetic setting setting, Ics-100 % Icu , service breaking capacity 36 KA.

Lugs suitable for 06 sqmm to 16 sqmm cable

Lugs suitable for 25 sqmm to 50 sqmm cable

Lugs suitable for 70 sqmm to 95 sqmm cable

Lugs suitable for120 sqmm to 240 sqmm cable

Lugs suitable for 300 sqmm to 400 sqmm cable

Epoxy type insulator upto 1100Volt for LT panel bus bar including nut bolts etc. complete

Digital Voltmeter 0-500 V range including connection with metering system

Digital Ammeter 0-400 A range including connection with metering system

Single core stranded Copper conductor FRLS of size 16 sqmm including copper lugs at both ends

Single core stranded Copper conductor FRLS of size 10 sqmm including copper lugs at both ends c

LED indicator lamp RYB

S&F Cable Junction Box 200X160X98mm in size, made out of thermoplastic sheet having IP 65 protection for outdoor installation fixed with 4 way bakelite cable terminals including 03 Nos polymide gland with check nut (M-32 - 2 nos) fixed on poles with flat iron clamps of size 25x3mm, nuts, bolts, washers etc. including applying Two Coats of Synthetic Enamel Paint over a Coat of Red Oxide Zinc Chrome Primer including taking out of old unserviceable cable junction box complete all as specified and as directed.

M&L SS pasivated Screw Bolts (Machine Made) with Hexagonal Head at one End and screwed the other Ends, each screwed End to be fitted with Washers and One Hexagonal Nut, diameter of Shank 5 to 10mm Length of Bolt exc. 50mm complete all as specified and as directed.

Supply and Fix Metal cable route indicator of height 750 mm MS Flat of 40 mm x 4 mm with Circular 100 mm diameter MS Sheet of minimun thickness 3 mm duly engraved " LT CABLE" including Aluminium paint over it and to be fixed 150 mm below ground level with PCC (1:3:6) (40 mm aggregate) of size 250x250x300 mm all as directed by Engr-in-Charge.

Dismantling of cross arms of MS channel or angle iron sections etc complete and setting aside all as specified

S&F of Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete including takig out the existing.

S & F in repairs Metal Rotary type locks for CRCA Sheet Panels as specified and directed.

Material & labour for Flexible PVC insulated multicore FR PVC sheathed multistranded copper conductor cable of size 2.5 Sqmm x 3 core for voltage grade up to 1100 V conforming to IS 694 : 2010 for connection of light fitting from junction box or from over head conductors to fitting incl taking out old unsv cable complete all as specified and as directed by Engineer-in-Charge.

Material & labour for Flexible PVC insulated multicore FR PVC sheathed multistranded copper conductor cable of size 1.5 Sqmm x 3 core for voltage grade up to 1100 V conforming to IS 694 : 2010 for connection of light fitting from junction box or from over head conductors to fitting incl taking out old unsv cable complete all as specified and as directed by Engineer-in-Charge.

M/L brick work with flyash bricks old size straight or curved on plan to any radius exc 6m mean radius build in CM 1:6 complete all as specified and directed.

M&L for 15mm thick in CM 1:4 rendering on brick or concrete surfaces finished fair and even on wall complete all as specified and directed.

Repair / Maint and overhauling of ACB of capacity 630Amp/800Amp/ 1000 Amp from existing position after disconecting the LT conections, open the outer cover,racking out , checking out spring charge motor, triping and closing coil, overhauling the complete unit by cleaning with suitable cleaning materials and replacement of minor spares ,internal electrical wiring and electronic accessories and insulated properly complete all as specified and directed by Engineer-in-Charge.

S&F in repair ACB Manual Draw out type 4 pole Microprocessor Based , 415 V adjustable type 630 Amps, with breaking capacity 50 KA including spreader link and separator and any modification required for fixing of ACB including taking down old unserviceable one complete all as specified and directed.

Supply,designing ,install, testing & commission 3 phase and neutral, 415 volts outdoor type, CPRI type tested having certification of IEC-61439 , factory made , dust and vermin proof, cubical type LT panel of size 1.10m x 0.45m x 1.10m, with canopy fabricated from 3.00 mm thick CRCA sheet for outer shell and 2 mm thick for non load bearing with angle iron frame of 50 x 50 x 6 mm, double door, front and back openable type, double door system, hinged opening, rubber lining, locking arrangement, with anticorrosive coating and finally epoxy polyester power coating with pure polyster Siemens grey structural RAL-7032 shade, protection class IP-66 fully compartmentalize design with 4 Nos of bus bar made of aluminium, 300 Amps rated (electrical grade aluminium complying with the requirements of latest BIS, colour coded), busbar extensions for cable connections of electrolytic grade . The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated pre-wired with suitable size of copper strip/copper wire with colour code for connecting out going MCCB/MCB's, including suitable aluminium earth strips conforming to IS with danger notice plate, necessary cable glands, cable connection with proper lugs, making electrical connection and circuit wiring for street light auto ON/OFF control timer by using desired electrical parameters PCC foundation and pedestal for fixing pillar feeder box/LT Panel with PCC 1:3:6, 15 cm thick in foundation, brick (Fly ash) / PCC block work in CM 1:6, rendering 1:6 on exposed surface and 100 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in padding on top and grounting bolts etc for panel. The platform shall be of 450 mm height above ground level all as specified with supply and fixing the following accessories including taking out the existing one :

(A) Incoming MCCB 160 Amps rating, FP ,415 V, AC, 50 HZ, adjustable thermal anf fixed magnetic setting Ics-100 % Icu , service breaking capacity 36 KA --- 01 Nos (B) Outgoing (b) MCCB 40 Amps rating, FP ,415 V, AC, 50 HZ, adjustable thermal anf fixed magnetic setting Ics-100 % Icu , service breaking capacity 16 KA --- 02 Nos. (c) MCCB 25 Amps rating, FP ,415 V, AC, 50 HZ, adjustable thermal anf fixed magnetic setting Ics-100 % Icu , service breaking capacity 16 KA --- 05 Nos. (d) Digital voltmeter 0-500 volt with selector switch -01 No e) Digital amp meter 0-100 Amp with set of current transformer of suitable rating and selector switch -01 No (f) Indicator lamp (RYB) LED type - 01 set (g) Control MCB 2.0 Amps SP- 03. Nos Note:- (i) All MCCB/MCB should be of approved Make (ii) Drawing of LT panel and make of items shall be get approved from GE before ordering the panel. (iii) Cost of lugs for cable and cable gland etc also included in unit rate of panel. (iv) The rating bus bar to out going MCCB / MCB`s shall not be less than 1.5 times the rated current of individual out going feeders/ MCCB. (v) Spreader terminals and Phase barriers to be provided with all MCCB`s (vi) Rate of panel include refixing of all cables in panel which are dismantle & taking out from old unserviceable panel.

All as per BOQ Item No 57.00 here-in-before but with the following incoming and outgoing accessories :- BUS BAR 4 Nos of bus bar made of aluminium, 250 Amps rated (electrical grade aluminium complying with the requirements of latest BIS, colour coded), busbar extensions for cable connections of electrolytic grade (A) Incoming MCCB 125 Amps rating, FP ,415 V, AC, 50 HZ, adjustable thermal anf fixed magnetic setting Ics-100 % Icu , service breaking capacity 16 KA --- 01 Nos. (B) Outgoing (b) MCB 25 Amps rating, TPN ,415 V, AC, 50 HZ, breaking capacity 10 KA --- 02 Nos. (c) MCB 16 Amps rating, TPN ,415 V, AC, 50 HZ, breaking capacity 10 KA --- 04 Nos. (e) Digital voltmeter 0-500 volt with selector switch -01 No e) Digital amp meter 0-100 Amp with set of current transformer of suitable rating and selector switch -01 No (g) Control MCB 2.0 Amps SP- 03. Nos (f) Indicator lamp (RYB) LED type - 01 set

All as per BOQ Item No 57.00 here-in-before but with the following incoming and outgoing accessories :- BUS BAR 4 Nos of bus bar made of aluminium, 400 Amps rated (electrical grade aluminium complying with the requirements of latest BIS, colour coded), busbar extensions for cable connections of electrolytic grade (A) Incoming MCCB 200 Amps rating, FP ,415 V, AC, 50 HZ, adjustable thermal anf fixed magnetic setting Ics-100 % Icu , service breaking capacity 36 KA --- 01 Nos. (B) Outgoing (b) MCCB 63 Amps rating, FP ,415 V, AC, 50 HZ, adjustable thermal anf fixed magnetic setting Ics-100 % Icu , service breaking capacity 16 KA --- 02 Nos. (c) MCCB 40 Amps rating, FP ,415 V, AC, 50 HZ, adjustable thermal anf fixed magnetic setting Ics-100 % Icu , service breaking capacity 16 KA --- 04 Nos (d) Astronomical Timer Switch 1 outlet 16 A-250V,vertical dial N/O contact,power supply 230V,50/60Hz,three position override switch "ON-AUTO-OFF" on front panel-01 Nos, 25A ,2 NO Contactor 3 phase, with 230V coil-01 Nos, 32 A MCB TPN-01Nos with suitable relay and other accessoris . (e) Digital voltmeter 0-500 volt with selector switch -01 No (f) Digital amp meter 0-100 Amp with set of current transformer of suitable rating and selector switch -01 No (g) Indicator lamp (RYB) LED type - 01 set (h) Control MCB 2.0 Amps SP- 03. Nos