Indian Oil Corporation Limited Tender

10m USB 3.1 Gen1 Extender Cable || SITC of USB Extender Cable. Connectors || USB Port 1 x USB 3.1 Gen1 Type A Male || Downstream 1 x USB 3.1 Gen1 Type A Female || USB Specification USB 3.1 Gen1 / 2.0 / 1.1 for Super / High / Full or Low speed || Cable Length 10 m || Data Rate Up to 5 Gbps

Retractable Motorized 21,5” Monitor RET-L Line for boardroom and meeting room tables - || SITC Of Retractable Motorized 21.5"" Monitor || Native Resolution 1920x1080 || Painted Steel Housing. 20º Tilt adjustment at user choice || Retractable Motorized 21.5” TFT monitor for boardroom and meeting room tables. 20º tilt adjustment that can be set according to user preference. || High-end painted steel monitor housing with square corners. || Automatic opening system for the cover plate, avoiding contact between monitor housing and the aperture. If an obstruction is detected on the cover plate, the system stops and reverts the movement. || Brushed aluminium cover plate. Monitor and cover plate can be customized with different finishings. || RS-232 serial control through DB9 connector. || RS-485/422 serial control through In/Out RJ45connector allowing loop and addressing DISPLAY || Panel Technology- Edge LED Technology || Display Area (mm) 476.64(H) x 268.11(V) || Size 21.5”Pixel Pitch (mm) 0.248 x 0.248 || Screen Aspect 16:9 || Native Resolution 1.920 x 1.080 || Viewing Angle UDLR 89º/89º/89º/89º || Contrast Ratio 5000:1 (Typ) || Brightness cd/m2 300 (Typ) || Colors -16.7M Colors || Response Time 16ms Ton +TofLife Time (hours) 50.000. || Analogue RGB Input 1xDB15Digital Input 1xDVI-DRS-232 Control 1xDB9RS-485/422 Control 2xRJ45 (In/Out) || CONTROL-Remote Control 1xRS232, 1xRS485/422Manual Control 2 Pushbuttons (Up/Down)2 Pushbuttons (Tilt adjustment) || ELECTRICAL- Power Adaptor 90 ~ 264VAC to 12VDC47 ~ 63HzPower Consumption 30WEnergy Management VESA DPMS

Cable Cubby || SITC of Cable Cubby with Option for HDMI, USB & Power

Wireless Presentation & Conferencing System || || SITC of Wireless Presentation System || Output resolution: (HDMI) up to 3840 × 2160 pixels @ 30fps || Video connections: 1 x HDMI1.4b (1 x output) || Number of sources: 2 x displayed simultaneously || Number of participants: 32 x connected (buttons or app connected) || Transmission: IEEE 802.11 a/g/n/ac, IEEE 802.15.1 || Authentication protocol: WPA2-PSK for individual operation, WPA2-PSK or IEEE || 802.1 x network operation || Transmission band: 2.4 GHz and 5 GHz, || Wireless data rate: Up to 300 Mbps || Audio sources: Broadcast quality, 16Bits 22.1 kHz || Lip sync support || Reach: 30m || Base unit: Connections: 1 x Ethernet LAN, 1 x USB-A, 1 x USB-C, 1 x Audio IN / Out via USB, Video/Audio Out via HDMI, 1 x WLAN, UC&C || Platform Agnostic: Yes || Network Connection: Wired (RJ-45) or Wireless (5-Ghz or 2.4-Ghz) || Dual Network Support- Yes || Wireless and Wired || Wireless Network Modes: Access Point or Wireless Client || POE+- Yes || Wireless Presentation support on or off with Network || Wireless Conferencing support on or off with Network || Wireless Presentation with button or app || Wireless Conferencing with button or app || Windows platform only Annotation || Whiteboard and Touchback capable, Miracast, Google Cast, and Airplay Support, Wireless Presentation || Automatic Meeting Room Connection – Present Sense

Full HD PTZ camera with 12x zoom || SITC of Full HD PTZ Camera || sensor 1/2.8" 2.41MP CMOS || Video Format HDMI:1080p 60 / 50 fps,720p 60 / 50 fps || USB:1080p 30 / 25 fps, 720p 30 / 25 fps || Video Output (HD) Interface HDMI / USB 3.0 || Optical Zoom 12x, || Digital Zoom 12x (HDMI Only) || Viewing Angle 72°(H) 80°(D) || Panning Angle +100° ~ -100° || Panning Speed 100°/ sec || Tilting Angle +30° ~ -30° || Tilting Speed 100°/ sec || Aperture F1.6~F2.8 || Focal Length f = 3.92 ~ 47.32 mm || Shutter Speed 1/1 ~ 1/10,000 sec || Minimum Object Distance 500mm (Wide) ~ 1500mm (Tele) || Video S/N Ratio 50dB || Minimum Illumination 1.6 lux (F1.8, 50IRE, 60fps) || Focus System Auto / Manual || Gain Control Auto / Manual || White Balance Auto / One-Push / Manual || Exposure Control Auto / Manual || WDR -Yes || 3D NR- Yes || Image Flip- Yes || Preset Positions 128 || Control Interface RS-232 In and Out / USB || Control Protocol VISCA / UVC || Video Stream YUV422 / MJPEG || IR Pass-through Yes || IR Receiver Yes || IR Remote Control Yes || Power Consumption 13W

Camera mount (wall/ceiling) || SITC for Camera Mount

  || 35 Ft HDMI Cable || SITC of 24k gold-plated HDMI premium high speed optical cable || Built-in active circuitry for inter conversion between electrical and optical signal || Powered by the connected source device || Data rates up to 18 Gbps || Video resolutions up to 4K/60 @ 4:4:4, and HDR, EDID, HDCP, and CEC pass through || Plenum rated || 35' (12 m)

Scaler with Seamless Switching and PIP - picture-in-picture || || SITC Of Five Input HDCP-Compliant Scaler with Seamless Switching which Integrates HDMI and analog video sources into presentation systems || should have Three HDMI inputs and two universal auto-detecting analog video inputs || Simultaneous outputs for HDMI and analog RGB or component video || Should support PIP - picture-in-picture || Should support Auto-switching between inputs || Should support Clean switch transitions || Should support Selectable output rates from 640x480 to 1920x1200, including 1080p/60 and 2K, Should support Advanced scaling engine with 30 bit precision processing and motion-adaptive deinterlacing for signals up to 1080i || Should support EDID || Should support Aspect Ratio Control || Should support HDMI specification features include data rates up to 6.75 Gbps, Deep Color, and HD lossless audio format || Should support HDCP Visual Confirmation || Accu-RATE Frame Lock || Image freeze control || Auto-Image™ setup || Auto Input Memory || Picture controls for brightness, contrast, color, tint, and detail, as well as horizontal and vertical positioning, and sizing || Quad standard video decoding || Should support Ethernet Monitoring and Control || Should have RS 232 Control Port || Should support ARP, ICMP (ping), IP, TCP, UDP, DHCP, HTTP || Telnet Ethernet Protocol

HDMI and Audio to USB Bridging Capture Device || SITC of HDMI and audio to USB C interface, for integration of an AV source or system with a computer in a soft codec video conferencing application || HDMI and audio to USB C scaling bridge with integrated audio control || Video processing || Variety of analog audio I/O ports and signal management for analog audio || HDMI embedded audio and USB bidirectional audio || Shall provide one (1) HDMI Type A connector for digital video signals with embedded audio || Shall provide one (1) HDMI Type A connector for buffered loop-through || Shall support HDMI computer and video resolutions up to 4K/60 and 4K/30 || Shall provide one (1) five-pole captive screw connector for mic/line audio || Shall provide selectable +48 volt phantom power || Shall support HDMI audio de-embedding for two-channel PCM audio || Shall support two channels of USB audio from the host computer || Shall provide analog to digital audio conversion at 48 kHz sampling rate with 24-bit resolution || Shall provide one (1) USB Type C connector for DP Alt digital video and bidirectional 2x2 audio signals || Shall support USB 3.0 standards || USB 3.0 device connection shall appear as generic USB webcam and speakerphone to host computer || Utilizes industry standard UVC - USB Video Class and UAC - USB Audio Class drivers || USB video and audio content shall be compatible with popular Unified Communications (UC) || Lecture Capture, or other USB streaming software || Shall provide one (1) connector for balanced/unbalanced line level stereo audio || Shall provide two channels of USB audio to the host computer || Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution || Shall provide a signal-to-noise ratio greater than 90 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted || Shall provide a THD+N measurement of less than 0.03% measured at 20 Hz to 20 kHz, at maximum level || Shall provide processing and conversion of video from HDMI to USB encoded video for the host computer || Shall provide audio signal management and optimization for analog audio, HDMI de-embedded audio, and USB bidirectional audio || Shall provide digital audio processing tools including gain, mixing, and ducking || Shall provide automatic EDID management || Shall provide HDCP-compliant capabilities on HDMI input and loop-through || Should support Ethernet monitoring and control

USB A to B cable 6' (1.8 m) || SITC of USB 3.2 Type-A male to Type-B male cables support SuperSpeed USB data at rates up to 5 Gbps and up to 4.5 watts of power for USB charging || USB specification USB 3.2 (Gen1) || USB 2.0, USB 1.1 compatible || USB data rate Up to 5 Gbps || Connectors 1 USB A Male to 1 USB B Male || Connector Type Gold plated || Length 6 feet or more || Regulatory compliance RoHS/WEEE/CE/UL-CMX

Extension Cables usb A to A || SITC Of USB Extension cable USB-A signal extension between the host and a peripheral device || Signal Type USB-A male to USB A female || USB Version USB 3.2 (Gen 1), 2.0, 1.1 compatible or more || USB Data rate 5 Gbps or better || Connector Type USB-A male to USB A female || USB power 5 V and up to 900 mA of power to the USB peripheral device or more Contacts || Gold plated || Length 25 feet or more || Regulatory compliance CE/ RoHS/UL-CMP/WEEE

8x8 HDMI Matrix Switcher || SITC of 8 x 8 HDMI Matrix Switcher with Audio De-embedding which supports computer and video resolutions up to 4K/60 @ 4:4:4 || Supports data rates up to 18 Gbps || HDR || Deep Color up to 12-bit || 3D || HD lossless audio formats || Supports maximum pixel clock of 600Mhz HDMI audio de-embedding with digital S/PDIF and analog stereo audio outputs || Should supports EDID management || HDCP 2.3 compliant || Supports HDR video || Supports DDC transmission || HDMI to DVI Interface Format Correction || Should support Ethernet monitoring and control || RS-232 control || Should support Ethernet protocol : ARP, DHCP, DNS, HTTP, HTTPS, ICMP (ping), IEEE 802.1X, NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, Telnet, UDP/IP || Unit can be fixed chassis or modular

DTP Transmitter for HDMI || SITC of HDMI transmitter transmitting HDMI plus control and analog audio up to 230 feet (70 meters) over twisted pair; || Supports computer and video resolutions up to 4K ; || Supports data rates up to 10.2 Gbps, || Deep Color up to 12-bit, 3D, HD lossless audio formats, and CEC pass-through ; || HDCP 2.3 compliant; || Supports up to 4:4:4 chroma sampling; s || Should support Maximum pixel clock 300 MHz; || Should support Audio Gain Unbalanced output: 0 dB; balanced output +6 dB,  || Frequency response  20 Hz to 20 kHz, ±0.5 dB , THD + Noise  0.03% @ 20 Hz to 20 kHz at maximum output ,  S/N  90 dB, at maximum output (15 dBu), balanced (unweighted),  Stereo channel separation  80 dB @ 1 kHz to 20 kHz

DTP Receiver for HDMI || SITC of twisted pair receiver which Receives HDMI plus control and analog audio up to 230 feet (70 meters) over twisted pair;  || Support computer and video resolutions up to 4K,  || Data rates up to 10.2 Gbps or better and CEC pass-through; || HDCP 2.3 compliant; || EDID Management; || Support up to 4:4:4 chroma sampling;  || Should support Maximum pixel clock of at least 300 MHz; || Should support Audio Gain of Unbalanced output: 0 dB; balanced output +6 dB,  || Frequency response of 20 Hz to 20 kHz, ±0.5 dB, THD + Noise of 0.03% @ 20 Hz to 20 kHz at maximum output, S/N of 90 dB, at maximum output (15 dBu), balanced, Stereo channel separation : 80 dB @ 1 kHz to 20 kHz

6ft HDMI patch cable || SITC of HDMI Patch Cable, || Cable Length 6 Feet || Signal Type HDMI 2.0 || Video Data rate support 18 Gbps or better || Supported Resolution 4K or more || Connector Type Gold plated contacts

Audio System

Table Top Boundary Layer Mic || SITC of cardioid pre-polarized condenser on-table boundary layer microphone with 3-pin XLR, programmable microphone button for Toggle on/off, PTM, PTT and permanent || Bi-color LED ring for status indication || TTL logic connector with logic inputs and outputs || Frequency response of 40 Hz - 20,000 Hz or better || Sensitivity of 10 mV/Pa or better || Nominal impedance at 1 kHz of 200 Ω or better || Current consumption of 5.3 mA or better || Maximum SPL of 140 dB or better || Operating on 48 V phantom power

Wireless Handheld Microphone Set || SITC of Digital wireless handheld Microphone with UHF transmission greatly enhances range || Reliability and scalability of 56 MHz Bandwidth will allow for up to 90 channels || Up to 2,200 or more selectable frequencies with Mobile App integration setup 134 dB or more transmitter dynamic range || Lithium Ion battery pack delivers up to 10 hours of operation (up to 6 hours of operation with AA batteries) || Transducer principle dynamic with Pick-up pattern cardioid || Sound pressure level 154 dB SPL || Transmit power : 10 mW ||

12x8 ProDSP Digital Matrix Processor with AEC || SITC Of 12x8 ProDSP Digital Matrix Processor models with 12 mic/line inputs and 8 line outputs || 12 channels of AEC - acoustic echo cancellation || AUDIO SYSTEM should include a configurable USB Audio interface- /output configuration of the USB Audio Interface can be set to 0x8, 2x6, 4x4, 6x2, or 8x0  || Up to 16 assignable and routable AEC processor instances || Should feature 64 bit floating point audio DSP processing || Equipped with selectable 48 volt phantom power for the first eight inputs || Should have studio grade 24‑bit/48 kHz analog‑to‑digital and digital‑to‑analog converters || 8 or more DSP Configurator presets || Should have  Audio system gain: Balanced output: 0 dB, unbalanced output: -6 dB or better, || Frequency response: 20 Hz to 20 kHz, ±0.2 dB or better,  Frequency response: 20 Hz to 20 kHz, ±0.2 dB or better,  || THD + Noise  0.01%, 20 Hz to 20 kHz or better, at maximum level, S/N: Analog In to Analog Out  107 dB, 20 Hz to 20 kHz, at maximum balanced output (unweighted), Analog In to Digital Out  110 dB, 20 Hz to 20 kHz, at full-scale output (unweighted), Digital In to Analog Out  115 dB, 20 Hz to 20 kHz, at maximum balanced output (unweighted) , || Crosstalk should be -90 dB @ 20 Hz to 20 kHz, fully loaded; || Audio input impedance 10k ohms balanced/unbalanced, || Nominal level should be -60 dBV, +4 dBu, -10 dBV adjustable via input gain,  || Maximum level should be +21 dBu at rated THD+N when mic gain is set to 0 dB, || Equivalent input noise should be -120 dBV (1 µVrms) at 40 dB input gain,  || CMRR  should be 60 dB typical or better,  || Input gain adjustment should be -18 dB to +80 dB in 0.1 dB steps, adjustable per input or better;  || Audio output impedance should be 100 ohms balanced, 50 ohms unbalanced or better, || Gain error should be ±0.1 dB channel to channel or better;

6x4 ProDSP Digital Signal Processor || SITC Of 6x4 ProDSP Digital Matrix Processor models with 6 mic/line inputs and 4 line outputs || Six channels of AEC - acoustic echo cancellation || AUDIO SYSTEM should include a configurable USB Audio interface- /output configuration of the USB Audio Interface can be set to 0x8, 2x6, 4x4, 6x2, or 8x0 || Should feature 64 bit floating point audio DSP processing || Equipped with selectable 48 volt phantom power for the first eight inputs || Should have studio grade 24‑bit/48 kHz analog‑to‑digital and digital‑to‑analog converters || 8 or more DSP Configurator presets || Should have Audio system gain: Balanced output: 0 dB, unbalanced output: -6 dB or better, || Frequency response: 20 Hz to 20 kHz, ±0.2 dB or better, || THD + Noise 0.01%, 20 Hz to 20 kHz or better, at maximum level, S/N: Analog In to Analog Out 107 dB, 20 Hz to 20 kHz, at maximum balanced output (unweighted), Analog In to Digital Out 110 dB, 20 Hz to 20 kHz, at full-scale output (unweighted), Digital In to Analog Out 115 dB, 20 Hz to 20 kHz, at maximum balanced output (unweighted) , || Crosstalk should be -90 dB @ 20 Hz to 20 kHz, fully loaded; || Audio input impedance 10k ohms balanced/unbalanced, || Nominal level should be -60 dBV, +4 dBu, -10 dBV adjustable via input gain, || Maximum level should be +21 dBu at rated THD+N when mic gain is set to 0 dB, || Equivalent input noise should be -120 dBV (1 µVrms) at 40 dB input gain, || CMRR should be 60 dB typical or better, || Input gain adjustment should be -18 dB to +80 dB in 0.1 dB steps, adjustable per input or better; || Audio output impedance should be 100 ohms balanced, 50 ohms unbalanced or better, || Gain error should be ±0.1 dB channel to channel or better;

Four Channel Amplifier || SITC of Four Channel Amplifier which shall provide 100 watts rms per channel into 4 or 8 ohms measured at 1 kHz with 0.1% THD || Signal-to-noise ratio of 100 dB measured from 20 Hz to 20 kHz, unweighted || Shall support bridging of adjacent odd/even output pairs to provide 200 watts rms output power into 8 ohms || Shall provide a THD+N measurement of 0.1% measured at 1 kHz, at 3 dB below clipping || Shall provide damping factor of greater than 100 at 8 ohms || Shall utilize an efficient Class D amplifier design || Shall be convection cooled and operate without fans or vents || Shall provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain without audible artifacts to eliminate clipping distortion || Shall provide multiple protection circuits that activate during output shorts, thermal overload, or DC faults || Shall provide power factor correction technology to remove harmonic content on the AC power line ||

Wall Mount speaker || SITC of Wal Mount Speakers with 6.5" (16.5 cm) polypropylene woofer || Shall consist of a 1" (2.5 cm) silk dome tweeter || Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space || Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program/ peak || Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space || Shall provide a nominal impedance of 8 ohms; Shall provide a crossover frequency of 2.5 kHz || Shall support 8 ohm direct connection from power amplifiers || Shall provide an internal overload protection circuit || Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation

Mount for speakers || SITC of Mount For Speaker

Control System

Control Processor || SITC of AV Control Processor || Supports 1x RS232/RS422/RS485, 1x bidirectional RS232 or more, 1 or more IR/Serial, 2 or more Relay, 4 or more x Digital IO || Control at least 30 devices over more Ethernet port supporting 10/100/1000Base-T || Support IEEE 802.1X, IPv4, TCP, UDP, DHCP, DNS, HTTPS, NTP, SFTP, SMTP, SNMP, SSH protocols. || SDRAM: Min 1GB or more || Flash Memory: Min 8 GB or more || Shall be supplied with necessary license to integrate with iOS/Android device || Built-in IR receiver for recording IR commands || Operational in up to 45°C temperature || Regulatory compliance: CE/UL or any equivalent

IR Emmitter & Shield Kit || SITC of IR emitter for remotely controlling AV equipment via a tiny infrared light-emitting diode with emitter shield included and cable length of at least 6 feet

10.2 inch Ipad silver 32 GB || SITC of CONTROL PAD MONITOR. 10.2-inch (diagonal) || LED-backlit Multi‑Touch display with IPS technology or better || Touch ID fingerprint sensor || Wi-Fi (802.11a/b/g/n/ac); dual band (2.4GHz and 5GHz). HT80 with MIMO Bluetooth 4.2 technology || Ambient light sensor || Native resolution of 1620 x 2160-pixel

Charging Point || SITC of Charging Point for Interface

Base Station || SITC of Base Station For Interface

Dual Band Wireless Access Point || SITC OF Access Point E5600 -Type Electro absorption Modulated Isolated Laser Module (EM-ILM) for Ultralong-Reach Applications

Room Scheduler panel with wall mount || SITC of 7 inch Room scheduler with 7" capacitive touchscreen with 1024x600 resolution or better. || AspectRatio:16:10 /16:9, || Brightness:420 cd/m2 or more, || SDRAM: 2 GB, Flash: 8 GB or better. || Supports Ethernet Data Rate: 10/100/1000Base-T, half/full duplex with autodetect || Ethernet Protocols : DHCP, DNS, HTTP, HTTPS, IEEE 802.1x, SFTP, SSH, TCP/IP, UDP/IP. || Shall be compatible to book the room using Microsoft® Exchange, Office 365™, Google Calendar™, 25Live®, EMS, NFS, and Ad Astra® etc. || Shall be PoE compatible. || Room scheduler shall have LED lights to show room availability. || Device shall be free from license for yearly subscriptions or to add more number of units. || Provided with mounting accessories

28- Port Gigabit Desktop Switch || SITC of 28- Port Gigabit Desktop Switch || 24 x 10/100/1000BASE-T PoE ports || 4 x Gigabit RJ45/SFP Combo ports || Advanced L2 switching and security features || L2+ Static Routing || Optional “standard mode” or “surveillance mode” management user interface || 193 W PoE budget

Installation & Cabling

Stereo Audio / Control Cable || SITC Of 22 AWG stranded (7x30) Stereo Audio / Control cable or better || High-conductivity tinned copper conductors or better || Polypropylene insulation or better || Should have PVC jacket || Operating Temperature Range: -20°C To +75°C or better || EU Directive 2011/65/EU (ROHS II) compliant or better || Non Plenum

Microphone bulk cable || SITC Of 24 AWG stranded (27x38) Microphone cable or better || High-conductivity bare copper conductors or better || Should have PVC insulation || Should have PVC jacket || Operating Temperature Range: -30°C To +60°C or better || Non Plenum

Speaker Cable || SITC Of Multi-Conductor - High-Conductivity Copper Speaker Cable || Twisted Jacketed Connector || 14 AWG stranded (42x30) tinned copper conductors || PVC insulation || PVC jacket. Operating Temperature Range : -20°C To +90°C or better || NEC/(UL) Specification: CL3 or equivalent || AWM Specification : UL Style 2587 (600 V 90°C) or equivalent || CSA Specification : FAS90 or equivalent || EU Directive 2011/65/EU (ROHS II) compliant or equivalent || EU RoHS Compliance or equivalent

Cabling and termination charges

RJ 45 Plugs || SITC OF Should be provided with shielded twisted pair for devices transmitting and receiving signal over twisted pair || Should be high performance Category 6A RJ-45 plug || Metal strain relief and ground bonding || Suitable for high EMI/RFI environments || Should be compatible with TIA/EIA 568A/B wiring standard || Conductor alignment guide should reduce crosstalk and signal interference || Should have Gold plated contacts

Shielded Digital Twisted Pair Cable || SITC OF Shielded twisted pair cable engineered for optimum signal transmission between devices transmitting and receiving signal over twisted pair || The cable is certified to 475 MHz bandwidth at distances up to 330 feet (100 meters) and has been independently tested and verified to meet performance requirements set by the HDBaseT Alliance || The cable should be engineered and tested to exceed HDMI error rate specifications of less than one pixel per billion at 100 meters || Should provide protection from outside interference and ensures high quality signal transmission || Should have SF/UTP design with four unshielded 24 AWG twisted pair conductors inside an overall braid and foil shield

RACK/CREDENZA FOR Keeping AV Equipment || SITC Of 36 U AV Equipment Rack || Multi Hollow Extruded Aluminum Frames Structure across the X, Y & Z axis to give an Uninstruct bolting mechanism ( UL ) and Further reinforced with 8 Nos. of corner bracket which ensure better stability and strength || Multi Hollow Extruded Aluminum Frames Structure across the X, Y & Z axis to give an Uninstruct bolting mechanism ( UL ) and Further reinforced with 8 Nos. of corner bracket which ensure better stability and strength || Dimension 600mm Width, 800 mm Outer Depth (600mm usable depth) || Top cover ventilated on all sides along the width and depth thereby enhancing exhaust of hot air || Cable entry provision is both at the top and bottom covers with 35mm round cable entry point || The cable entry provision comprising of a gland plate with cable entry points in round cut outs edge protected with rubber grommets || Castor – 4 Nos. of heavy duty castors to take care of heavy load bearing capacities are provided || Earthing Strip – Copper strip to take care

SITC Of Cat-6 Cable

Delivery, Installation, Commissioning, Programming, Training & Hand Over charges

INTERIOR, ELECTRIC & ACCOUSTICS

Dismantling Of Existing system || Dismantling & dis-integration of existing conference table & AV system & stacking of re-usable items at designated location within IOCL premise.

Dismantling of Existing Wall Panel/False Ceiling, Conduit etc. || Dismantling of existing wall panel and necessary cutting of false ceiling, taking out existing light fittings and disposing/stacking them at designated location within IOCL premise.

PVC Conduit || Supply and laying of 2mm thick rigid PVC conduits in concealed conduit system using conduit accessories like junction boxes, collars, bends, elbows, binding wires, etc., 25mm dia conduit + 3 x 2.5 sqmm. Cu wire. || Approved Make: Any Brand ISI Marked

UPS Power Point || UPS Power Point 3 x 6A socket + 1 x 16A switch. || Approved Make: CRABTREE / INDO-ASIAN / ROMA / LEGRAND

Power Socket || Raw Power Socket 1 x 6/16A socket + 1 x 16A switch. || Approved Make: CRABTREE / INDO-ASIAN / ROMA / LEGRAND

UPS Power Point || UPS Power Point 1 x 6A socket + 1 x 6A switch || Approved Make: CRABTREE / INDO-ASIAN / ROMA / LEGRAND

Flooring Work || Making good the floor chase with cement sand mortar and leveling the base with existing floor for laying of carpet. || Approved Make: Cement : ULTRATECH / AMBUJA / ACC / DALMIA

Door Shifting || Shifting position of existing door to pantry by closing the existing door opening and creating the new door opening as per direction of the EIC.

Decorative laminate Panelling || ·  Providing and fixing Decorative Laminate Panelling, || ·  Base made with 12mm thick commercial plywood on 19 x 40mm ply strip/framework. || ·  Ply surface to be finished with 1mm laminate and grooves as approved. Item includes wooden mouldings duly polished as per design/instruction. || · Approved Make: PLYWOOD : GREEN ECOTEC / SYLVAN / ARCHID / GLOBE ; LAMINATE : MERINO / AICA / CENTURY / GREENLAM

Acoustical Slats Wood based MDF panels || · Providing and fixing Grooved Acoustical Slats Wood based MDF panels with linear perforations. || · The melamine laminate in size 2440mm x 128mm x16mm type 28/2 i.e. having 28mm strips and 2mm groove, tongue and groove edges for seamless mounting having density of 600kg/m3. || · The back of the panels are perforated with 8-10mm diameter circular holes with black acoustic fleece covering for providing sound absorption. || · Panel is wooden slat will be backed with polyester fibre 1000 gsm. Wooden slat will be fixed on 19 x 50mm ply strip/framework. || ·Approved Make: SLAT WOOD : THERMOFRIZ / HIMALAYAN / Equivalent

Providing and fixing PET sheets || || ·Providing and fixing PET sheets : 2440mm x 1220mm x 9mm thick sheet over 12mm MDF proper acoustic with GI frame work 600 x 600 c/c. || || ·Specification of Sheet is as following- || || Density : 9mm PET sheet 120-140kg/cum under IS 1734 (PT-1) – 1983 || Weight : 1.20 - 1.30 Kg/sqmt. || NRC : 0.70 || Fire Resistance : 25 (A grade) by ASTM – E84 || Smoke Density Index : 300450 by ASTM – E84 || Composition : 100% polyester Fibre. || || ·Base to be provided with wood wool panels made of wood fibre 1mm width magnesium composites 15mm thick fibril as per the choice of the Architect of size 1220 x 610mm, having noise absorption as per ISO:354-1985 and ASTM 423-90 a, || || · Density 400 kg/cum, || || ·Meets Fire Ratings ASTMD-876 and Fire Class -1 as per BS 476 part 5 and 6, Class P-not easily ignitable as per BS-476-Part 5 (Ignitability for material). This is applicable for core and class 1 as per BS 476-Part 7 (Method for classification of surface spread of flame), || ·Weather resistance as per IS 3308, || || ·  Thermal insulation as per IS:3346 with relative humidity of 90% RH at 60o Celsius for 15 days, conforms to En-13168 and are RoHS Complaint. || || · The panel will be backed with Rockwool 50mm thick and density 48kg/cum. PET panels to be pasted on top of wood wool board according to the design. || || · Approved Make: PET Sheets : THERMOFRIZ / TAP Equivalent

Window & Door Architrave || Providing and fixing Window & Door Architrave with 12mm thick commercial plywood on all sides to be finished with 1mm laminate and grooves as approved. Approved Make: PLYWOOD : GREEN ECOTEC / SYLVAN / ARCHID / GLOBE ; LAMINATE : MERINO / AICA / CENTURY / GREENLAM

Acoustics Ceiling || Providing and fixing 600mm x 600mm (0.5/0.55 NRC) Acoustic Ceiling Tiles with white colour silhouette exposed grid system, gird to comprise main runners spaced at 1200mm centre to centre securely fixed to structural soffit by approved hangers at 1200mm maximum centre to centre and not more than 150mm from spliced joints. || The last hanger at the end of each main hanger should not be greater than 600mm from adjacent wall. || Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to from 1200 x 600mm modules. || Cut cross tees longer than 600mm require independent support. || 600 x 600mm modules to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200mm cross tees. || Perimeter trim to be silhouette wall angle or channel secured to walls at 450mm maximum centres. || The rate shall include cutting of the tiles for light fixtures / A.C. diffusers & any other MEP provisions etc. and providing necessary and additional frame work for fixing the same. || Wherever channels are cut in this process, additional support shall be made for proper stability. || Approved Make: ARMSTRONG / USG / AMF / ANUTONE

Suspended gypsum False ceiling || Providing and fixing Suspended False Ceiling using 12.5mm thick Gypsum boards confirming to IS 2095-1982 and GI framework of approved make as per architectural drawing and instructions comprising of following. || || GI perimeter channel of 0.50mm thick having one flange of 20mm, another of 30mm and web of 27mm fixed to brick wall partition along periphery of ceiling with the help of nylon sleeves and screws at 610mm c/c. || || GI intermediate channel of size, 45mm web, two flanges each of 15mm & thickness 0.9mm ) suspended from the soffit / ceiling at 600mm c/c spacing. || || || GI ceiling sections of 0.50mm thick having knurled web of 51.5mm and two flanges each of 26mm with leaves of 10.5mm fixed to intermediate channel with the help of connecting clip at direction perpendicular to the intermediate channel at spacing of 600 mm c/c. || || GI suspender angle of 25mm x 10mm and thk. 0.50mm at spacing of 600mm c/c, fixed to the ceiling / soffit using GI cleat angle 25mm x 25mm, 0.50mm thk. cleat angle to be fixed to the ceiling / soffit using 6mm dia anchor fastener. || || Approved Make: GYPROC / USG BORAL / INDIA GYPSUM / GYPSOMAN

Zebra Blinds || Supply and installation of Zebra Blinds in windows , all complete. Approved Make: VISTA / MAC / MARVEL / ECOSOFT

Upgradation of existing Doors || Upgradation of existing Doors by pasting 1mm laminate on 6mm thick plywood on both sides of the door including fixing new handles, lock and accessories as required. || || Approved Make: PLYWOOD : GREEN ECOTEC / SYLVAN / ARCHID / GLOBE ; LAMINATE : MERINO / AICA / CENTURY / GREENLAM ; FITTINGS : GODREJ / DORSET / OZONE / HARDWYN

Providing and applying Emulsion Paint || Providing and applying Emulsion Paint, 2 coats over 1 coat water-based primer after surface preparation by scrapping and applying putty punning wherever required for achieving smooth surface. || Approved Make: ASIAN PAINTS / BERGER / ICI / NEROLAC

Console Storage || Providing and fixing of Console Storage made with 19mm thick commercial plywood and finished with 1mm laminate on exposed surfaces. Inside surfaces to be finished with balancer laminate. Storage below to be provided complete with hardware & fittings. || Depth- 600mm, height- 750mm. || || Approved Make: PLYWOOD : GREEN ECOTEC / SYLVAN / ARCHID / GLOBE ; LAMINATE : MERINO / AICA / CENTURY / GREENLAM ; FITTINGS : EBCO / HETTICH / GODREJ / HAFELE

Carpet Tile || Providing and fixing of Carpet Tile of approved shape and size, 100% PP with PVC backing of pile height 3mm & total height 6mm in multi-level loop construction, fixed with adhesive as per manufacturer's specification. Approved Make: SOLUTIA / ANEMORE / ELM / HERITAGE

Smart Wifi Aura LED Downlighter || Supply and installation of 10 Watt Philips Smart WIFI Aura LED Downlighter. Approved Make: PHILIPS / WIPRO / LEDVANCE / Equivalent

Smart WIFI TW Strip || Supply and installation of Philips Smart WIFI TW Strip 5M length housed in Aluminium profile 25mm x 12mm. || Approved Make: PHILIPS / WIPRO / LEDVANCE / Equivalent

WIFI remote Control || Supply of WIFI remote control.|| Approved Make: PHILIPS / WIPRO / LEDVANCE / Equivalent

Conference Table || Providing and fixing of Conference Table for 21 Pax, including wire management provision all complete as per approved design. Excluding cable cubby and IT/AV accessories. || || PLYWOOD : GREEN ECOTEC / SYLVAN / ARCHID / GLOBE ; LAMINATE : MERINO / AICA / CENTURY / GREENLAM ; FITTINGS : EBCO / HETTICH / GODREJ / HAFELE

IOCL LOGO || Supply and installation of IOCL Logo, made in stainless steel with colour heat print. Overall size of Logo with letters - 18" x 18".

IOCL LOGO-Pasting || Supply and pasting of IOCL Logo in vinyl print, size - 24" x 24".

Air Conditioner (this will be additional cooling on top of the existing Air conditioning system available in the hall)

Cassette AC || Supply of Cassette Air-Conditioner, 3.0 TR with R-32 Gas of make Daikin or equivalent. || DAIKIN / BLUESTAR / CARRIER / VOLTAS, Star Rating : Inverter 5 Star , 1 Year Warranty on Total Machine, 3 Years Warranty on Compressor

Cassette AC Installation || Installation of Cassette AC.

Copper Refrigerant Pipe || Supply and installation of Copper refrigerant pipe including 9mm nitryle foam insulation for Cassette AC.|| Approved Make: RAJCO / TOTALINE / MANDEV / Equivalent

Drain Pipe || Supply and installation of Drain pipe including 13mm nitryle foam insulation for Cassette AC. || Approved Make: ASTRAL / SUPREME / ASHIRBAD / Equivalent

Control Cable || Supply and installation of control cable 4 core x 1.5 sqmm. for Cassette AC. Approved Make: POLYCAB / HAVELLS / FINOLEX / RR