Military Engineer Services Tender

S&F prepainted aluminium zinc steel sheet (galvalume base) or thinknee 0.50mm having tensile strength of 550 MPA , in colour and profile as apporved by GE and to be facotry moulded as in roof covering /cladding and fixed with hot dipped galvanished with high durable protective triple coated self tapping screws /self drilling serews, to suit the roofing in customized colour matching with the colour of roofing and screws are to be fixed using torque adjustable electronic gun screws drills of suitable capacity complete all as specified.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Dismantling timber scantlings 40 sq. cm and over in section, in any positioncomplete all as specified and directed.

Material and Labour in repairs second class hard wood in scantling, clean swan ,incl to replace old and delayed timber (including piecing, scarfing, etc., of old and new timbers if required) complete all as specified.

M&L for Rolled sections channel angle Tee section and in tubular section as in main and cross beams, hip and jack rafters; purlins,post where connected to common rafters and running rails and embbeded in concrete of Fe 410 (GDe 250) complete all as specified and directed.

S&F MS work as in wind ties for roof including securing bolts complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level).

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 20mm graded agg as in plinth protection incl all necessary form work & finishing surface even & smooth without using extra cement complete all as specified and as directed.

Taking down Chowkhats or frames not exc. 1.5 sqm each (without taking off shutters from frames) complete all as specified and directed.

S&F aluminium three track powder coated of any color (thickness of powder coating not less than 50 micron) sliding window with three sliding shutter the size of outer frame three track 92x31.5x1.2mm (using two track for glazed window shutter and one track for wire gauged), the section shutter size 37x18x1.2mm) and glazing with 4.8mm thick glas (Plain/floated) incl allround suitable rubber gasket and MS wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminium flat and inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle incl rocking arrangement & 2 numbers sliding rollers of nylon with incl all necessary fittings complete all as specified and directed.

Taking down Chowkhats or frames 1.5 sqm but nexec 4 sqm each without taking off shutters complete all as specified and directed.

S&F plain framed solid, st chowkhats and frames, wrought rebated on solid rounded or chamfered put together with glue pinned supplied and fixed 2nd class hard wood complete all as specified and directed.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face paness, commercial type on both sides complete all as specified and as directed.

M&L for 0.9mm thick decorative laminate type 1 of surface finish, colour and patters as approved, fixed with approved adhesive as per manufacturer's insturctions, complete all as specified and directed.

S&F 35 mm thick glazed and skelton shutter open rebated and prepared to receive glass, gauge etc,(with out sash bars) edges of framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Sec-8, clause 8.23(a) 2nd class hard wood (Shisham), 35mm thick shutter. complete all as specified and as directed.

S&F mild steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4 mm and fixed with alluminium staple and around all beading complete all as specified and as directed.

S&F Aluminium anodised, barrel tower bolts of ex- trudedsection 150mm long complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts 300mm long complete all as specified and directed.

Supply & fixing butt hinges medium weight cold rolled mild steel of 100mm long complete all as specified and directed.

S&F Aluminium handle alloy fabricated type 150mm long complete all as specified and directed.

M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for PCC 1:3:6 type C-1(using 20mm graded stone agg) for bed block for fixing hold fast complete all as specified.

S&F framed work such as grills,gratings, etc with ends of bars shouldered and / or riveted or forged into spikes; framed guard ; barred iron doors; ladders ; framed balusters; walk ways; railing and simillar work Con-forming to Fe 290 Gde E-165.

Taking down cement plaster on brick or stone walls etc raking out joints hacking for key scrabbing down water etc complete all as specified and directed.

Material and labour for 15mm thick cement plaster in CM (1:4) on fair faces of brick or concrete surfaces using WPC where ever required as per manufacturerer's instructions and finishing the surface even and smooth (without using extra cement) etc. complete all as specified and directed. NOTE -WPC shall be measured and paid separetely.

Supply only WPC complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M & L Preparing new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted over & including a coat of chalk whiting complete all as specified and directed.

M&L Preparing newly plastered surfaces and applying two coat of cement base paint over a coat of primer complete all as specified and as directed.

M&L for applying two coats of synthetic eneamel painting over a coat of pink primer on new/old untreated wooden surfaces exc 10 cm width or girth including preparation of surfaces complete.

M&L preparation of steel Surfaces of any description, over 10cm in width or girth,and applying two coats of synthetic enamel paint over a coat of red oxide primercomplete all as specified and directed.

Supply & fixing Decorative MS chromium plated tubular curtain rail of 25mm dia incl brackets on each end and one no of globe/roller, stops etc on each end of the rod per opening of door / window (make and materail approved by Engineer-in-charge) complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) any thickness, including cover fillets but without frame work complete all as specified and directed.

Supply & fixing of powder coated aluminium anodised snap grid frame work for false ceiling comprising of the following sections for making partitions of 605x605 mm size fixed to walls with rawl plugs & screws and hanged to roof with and including 2mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 37mmx24mmx0.3 mm thick , cross tee shall be 28mmx24mmx0.3mm thick and wall angle shall be 24mmx24mmx0.3 mm thick complete all as specified and directed.

Supply & fixing 4mm thick non asbestos E-board cememt building board for insulation and accoustic purpose in ceiling, 600 x 600 mm size fixed with staples on snap grid as in ceiling complete all as specified and directed.

BOQ/Sch 'A' E/M portion Taking down carefully aluminium/copper wiring of any size (for light, fan, socket or power etc complete) including fixture and fittings such as switches, sockets, ceiling roses, pendent holders regulators, tube lights etc and making good disturbed surfaces of wall, roof etc to match with existing surface.

Supply & Fixing point wiring for one light point/ fan point controlled by one, one way switch with 1.5Sqmm size, PVC insulated and unsheathed 1100volts grade, single core stranded (multistrand) copper conductor (FRLS) PVC cable drawn into & including medium grade PVC conduit (not less than 20mm outer dia ) with all fittings and accessories fixed concealed (including chase cutting in brick/ stone masonry walls for fixing conduit and plastering and whitewash/colouring the external surface and matching the same with existing surface) and sunk cast iron or pressed steel terminal boxes for mounting fittings like switches, sockets & fan regulators etc with 3 mm thick plastic laminated sheet covers fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.5 Sqmm multistranded copper conductor cable earth wire and connected to earth dolly complete all as specified and directed (Note:- wiring shall be done in colour coding as directed by Engineer in charge.

All as per item No. 41 herein before but one socket outlet 5 Amps on the same board.

All as per item No.41 herein before but one 3 pin socket outlet 5 Amps independent.

All as per item No. 41 above but with 2.5 Sq mm two single core and 2.5 Sq mm one single core as earth wire for 5/15 Amps socket.

supply & Fixing lamp holder PVC insulated body with back plate for angle/battern fitting complete all as specified and directed

Suppy & Fixing switch piano flush type single pole, one way 5 Amp complete all as specified and directed.

Supply & Fixing switch piano, flush type single pole 15 Amp complete all as specified and directed.

Supply & Fixing socket outlet 2 in 1, 3 pin, 5 and 15 Amp flush type complete all as specified and directed.

Supply & Fixing socket outlet 2 in 1, 3 pin, 5 Amp flush type complete all as specified and directed.

Supply & Fixing steped type electronic fan regulator flush type on the existing phenolic laminated sheet etc.

Supply & Fixing ceiling rose, PVC/ Poly carbonate, isolated body three terminal complete all as specified and directed.

Supply & Fixing sheet metal enclosure for DBs(double door type) TPN 4 way including blanking plate as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed .

Supply & Fixing sheet metal enclosure for DBs(double door type) single pole and neutral 8 way including blanking plate as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed .

Supply & Fixing 415V, 10KA 'C' curve miniature circuit breaker (MCB) of TPN 63 Amp and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed .

Supply & Fixing 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 40 to 63 Amp and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed .

Supply & Fixing 240V, 10KA 'B' curve miniature circuit breaker (MCB) of single pole 5 to 32 Amp and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed .

Material and labour for Sub main wiring with 2 run of 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to and including Rigid non metallic PVC conduit ( ISI marked) Heavy grade, 20 mm dia (external) inclusive of junction/terminal boxes, all fittings and accessories fixed concealed with and including 6.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB including cutting and chasing and making good surface as original by plastering and whitewash/ colour/ distemper etc including taking down existing old sub main wiring complete all as specified. Note :1 The cost of earth wire is included in the quoated rates. 2. Two run of 6 sqmm, one run of 6 sqmm and one run of PVC conduit will be measured as one unit ie one running metre”

Supply and fixing LED lights fitting 1x 20W (warm/milky white as required on site), 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and life of tube light not less than 50,000 hours.complete all as specified and directed.. Make Havells cat pat LUMILINEBS20WLED865SPCWH or equivalent of phillips/wippro/Bajaj/Surya complete Note:- LED tube light shall be purches to get minimum 2 year warrenty of material from manufracturer.

M&L for taking down ceiling fans / wall mounted fans of any size / sweep after disconnecting the wire from existing ceiling rose and depositing to MES store yard complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories (incl ceiling clamp/hook fixing in ceiling/roof with fashner/nut & bolts), 230 V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)complete all as specified and directed by Engineer-in-Charge.

S & F LED light fitting 1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. Make : Havells cat pat HEXAFT10WLED857SSYMBOPC or equivalent cat part in make phillips/wippro/Bajaj & C&S . Note:- Contractor shall submit 2 year warrenty of material from manufracturer alongwith purchase voucher.

M&L for Earthing complete with galvanized sheet earth plate electrodes 600x600x6.3 mm thick buried directly in ground (earth pit not less than 2. 25mtr deep below ground level) with top edge of plat not less than 1.5 mtr below normal ground level connected to galvanized iron strip 25 x 4 mm as earthing lead by means of bolts, nuts , check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 and including excavation and earth work, GI pipe light grade 15 mm bore for protection of GI wire from earth electrode to and incl the earth test point of galvanized Iron/steel of size 75x75x 25mm, supplying and laying charcoal dust, common salt, PCC 1:2:4 type B1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced with 6 mm dia TMT bars @ 75mm C/C both ways with MS handle 12mm dia, PGI funnel and wire mesh,20 mm dia GI pipe light grade for watering and connected to earth test point including brazing at all joints except at test point and testing complete all as specified and directed by Engr-in-Charge.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade, cross section area 16 Sqmm 4core laid in trenches or passing through pipes/ducts and incl the disturbence surface of road making good with using PCC complete all as specified and directed. Including taking down old LT U/G Cable from trenches/protection pipe etc complete.

Excavation in trenches not exceeding 1.5 mtr wide, depth exceeding 1.5 mtr and getting out in hard/dense soil complete all as specified and directed by Engineer-in-charge

Returning, filling incl spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil all as specified and directed.

Removing excavated material (soil) not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

M&L for dry clean sand filling in trenches below and around under ground cable cushioning complete all as specified and directed.. Note :- Thickness of sand cushioning shall be measured after punning.

M&L for brick sub class 'B' for protection of cable comlete all as specified and directed.

Supply and Fixing steel tube Light grade galvanised 50 mm bore with all fittings for protection of UG cable under road/culvert and fixing on wall with saddle, screw complete all as specified and directed.

Taking down and Supply, installation, testing & commissioning LT panel Out door type, suitable for operation on 415 volts, AC 3 phase, 4 wire, 50 Hz electric supply system, made out of CRCA sheet outer box thickness 3.15 mm and inner box thickness 2 mm, IP-54 Protection side covers with front and back hinged doors with proper locking arrangement including side cable alley, rubber gasket on front and back door to make it dust and vermin proof, powder coated , The cubicle shall have frame work, bottom frame & 45 CM long four legs of size 50 x 50 x 6 mm Angle iron, including 300 Amp TPN aluminium busbar sleeved with heat shrink sleeve colmmour coated for 3 Phase, 4 wire electric supply system and control wiring with minimum size: 1.5 SQmm of copper cable complete comprising of following accessories all as specified and any other items required for smooth functioning of LT Panel is deemed to be included in the rate quoted for the items and as directed by the Engr-in-charge. (Note: Feeder pillar box shall be mounted on PCC 1:2:4 type B-1 (with 20 mm graded stone aggregate) foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC foundation shall be deemed to be included in the unit rate quoted for the item ( Note:-All type Test Certificates and Design varification with switch gears ( ACB & MCCB) as per confirming to IS/ IEC: 61439/2011 Part-1 and part -2 with short circuit test at 65 KA, should be submitted by the contractor before executing the job.) INCOMMER:- MCCB, 200 Amps FP, 25KA, -01 No. ( As in-commer) METERING:- 3-Phase Digital Volt. Meter with inbuilt selector switch -01 Set 3-Phase Digital Amp. Meter with inbuilt selector switch -01 Set CT 200/5 A -03 Nos. RYB Indicating Lamp LED type 240 V AC -03 Nos. Control MCB SP 6A.-03 Nos. 200 A Manual Changeover SWITCH Suitable 9 Nos outgoing Cable for Three Phase with suitable Nuts and bolts

Supply, installation, testing & commissioning 250 KVAR, LT panel board for High Mast, Out - door type, double door, suitable for operation on 415 volts, AC 3 phase, 4 wire, 50 Hz electric supply system, made out of CRCA sheet outer box thickness 3.15 mm and inner box thickness 2.0 mm, side covers with front and back hinged doors with proper locking arrangement, rubber gasket on front and back door to make it dust and vermin proof, powder coated , The cubicle shall have frame work, bottom frame & 45 CM long four legs of size 50 x 50 x 6 mm Angle iron, including 750 Amp TPN aluminium busbar sleeved with heat shrink sleeve colmmour coated for 3 Phase, 4 wire electric supply system and control wiring with minimum size: 1.5 SQmm of copper cable complete comprising of following accessories all as specified and any other items required for smooth functioning of AMF Panel is deemed to be included in the rate quoted for the items and as directed by the Engr-in-charge. (Note: Feeder pillar box shall be mounted on PCC 1:2:4 type B-1 (with 20 mm graded stone aggregate) foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC foundation shall be deemed to be included in the unit rate quoted for the item.( Note:-All type Test Certificates and Design varification with switch gears ( ACB & MCCB) as per confirming to IS/ IEC: 61439/2011 Part-1 and part -2 with short circuit test at 65 KA, should be submitted by the contractor before executing the job.) INCOMING:- 750 Amp TPN aluminium busbar - 01 Set 500A, 4P, MCCB 36 KA, Adj, ICS= 100% ICU- 01 No SPREADER LINK-01 Set ROH- 01 No. METERING:- MFM, for V,I,F,PF - 01 No. CT 500/5 - 01 Set CT connection link -06 Nos RYB Indicating Lamp LED type 240 V AC - 01 Set APFC Relay, 8 Steps, MICRO based (1-CT input) - 01 No. CT 500/5 Amps Auto mannual switch - 01 No. OUTGOINGS:- 50 KVAR BANK:-04 Nos. :- 100A, 3P, MCCB 25 KA, Adj, ICS= 100% ICU - 01 No.

Spreader Links - 01 Set Capacitor, MPP, HD,, 480 V, 3-P, 50 KVAR - 04 Nos Capacitor duty contactor, 50 KVAR -04 Nos ON indicator -04 Nos ON-OFF Push button with elements -04 Nos MCB 6 A, SP, C' Series, 10KA -04 Nos 25 KVAR BANK:- 01No. :- 63A, 3P, MCB 10 KA - 01 No. Capacitor, MPP, HD, 480V, 3-P, 25KVAR - 01 Nos Capacitor duty contactor, 25 KVAR - 01 No. ON indicator - 01 No. ON-OFF Push button with elements -02 Nos MCB 6 A, SP, C' Series, 10KA - 01 No. 10 KVAR BANK:- -02 Nos. :- 20A, 3P, MCB 10 KA -02 Nos. Capacitor, MPP, HD,, 480 V, 3-P, 10 KVAR -02 Nos. Capacitor duty contactor, 10 KVAR -02 Nos. ON indicator -02 Nos. ON-OFF Push button with elements -04 Nos MCB 6 A, SP, C' Series, 10KA -02 Nos. 5 KVAR BANK:- 01 No. :- 16 A, 3P, MCB 10 KA - 01 No. Capacitor, MPP, HD,, 480 V, 3-P, 05 KVAR =- 01 No. Capacitor duty contactor, 5 KVAR - 01 No. ON indicator - 01 No. ON-OFF Push button with elements -02 Nos MCB 6 A, SP, C' Series, 10KA - 01 No. AXIAL Fan 150 MM with thermostate -04 Nos Wiring with accessories - 01 Lot.

Supply, installation, testing & commissioning 80 KVAR, LT panel board for High Mast, In - door type, , suitable for operation on 415 volts, AC 3 phase, 4 wire, 50 Hz electric supply system, made out of CRCA sheet outer box thickness 2.0 mm and inner box thickness 1.6 mm, side covers with front operated with proper locking arrangement, rubber gasket on front and back door to make it dust and vermin proof, powder coated , The cubicle shall have frame work, bottom frame & 45 CM long four legs of size 50 x 50 x 6 mm Angle iron, including 250 Amp TPN aluminium busbar sleeved with heat shrink sleeve colmmour coated for 3 Phase, 4 wire electric supply system and control wiring with minimum size: 1.5 SQmm of copper cable complete comprising of following accessories all as specified and any other items required for smooth functioning of AMF Panel is deemed to be included in the rate quoted for the items and as directed by the Engr-in-charge. (Note: Feeder pillar box shall be mounted on PCC 1:2:4 type B-1 (with 20 mm graded stone aggregate) foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC foundation shall be deemed to be included in the unit rate quoted for the item.( Note:-All INCOMING:- 250 Amp TPN aluminium busbar - 01 Set 160A, 4P, MCCB 25 KA, Adj, ICS= 100% ICU - 01 No. SPREADER LINK -01 Set ROH - 01 No. METERING:- MFM, for V,I,F,PF - 01 No. CT 160/5 -01 Set CT connection link -06 Nos RYB Indicating Lamp LED type 240 V AC -01 Set APFC Relay, 6 Steps, MICRO based (1-CT input) - 01 No. CT 160/5 Amps - 01 No. Auto mannual switch - 01 No. OUTGOINGS:- 25 KVAR BANK:- 02No. :- 63A, 3P, MCB 10 KA -02 Nos Capacitor, MPP, HD,, 480 V, 3-P, 25 KVAR -02 Nos Capacitor duty contactor, 25 KVAR -02 Nos ON indicator -02 Nos ON-OFF Push button with elements -04 Nos

MCB 6 A, SP, C' Series, 10KA -02 Nos 10 KVAR BANK:- 02 No. :- 20A, 3P, MCB 10 KA -02 Nos Capacitor, MPP, HD,, 480 V, 3-P, 10 KVAR -02 Nos Capacitor duty contactor, 10 KVAR -02 Nos ON indicator -02 Nos ON-OFF Push button with elements -04 Nos MCB 6 A, SP, C' Series, 10KA -02 Nos 5 KVAR BANK:- 02 No. :- 16 A, 3P, MCB 10 KA -02 Nos Capacitor, MPP, HD,, 480 V, 3-P, 05 KVAR -02 Nos Capacitor duty contactor, 5 KVAR -02 Nos ON indicator -02 Nos ON-OFF Push button with elements -04 Nos MCB 6 A, SP, C' Series, 10KA -02 Nos AXIAL Fan 150 MM with thermostate -02 Nos Wiring with accessories -01 Lot

Supply, installation, testing & commissioning MOTOR CONTROL, LT panel board for High Mast, In - door type, , suitable for operation on 415 volts, AC 3 phase, 4 wire, 50 Hz electric supply system, made out of CRCA sheet outer box thickness 2.0 mm and inner box thickness 1.6 mm, side covers with front operated with proper locking arrangement, rubber gasket on front and back door to make it dust and vermin proof, powder coated , The cubicle shall have frame work, bottom frame & 45 CM long four legs of size 50 x 50 x 6 mm Angle iron, including 150 Amp TPN aluminium busbar sleeved with heat shrink sleeve colmmour coated for 3 Phase, 4 wire electric supply system and control wiring with minimum size: 1.5 SQmm of copper cable complete comprising of following accessories all as specified and any other items required for smooth functioning of AMF Panel is deemed to be included in the rate quoted for the items and as directed by the Engr-in-charge. (Note: Feeder pillar box shall be mounted on PCC 1:2:4 type B-1 (with 20 mm graded stone aggregate) foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC foundation shall be deemed to be included in the unit rate quoted for the item.( Note:-All INCOMING:- 150 Amp TPN aluminium busbar - 01 Set 100A, 4P, MCCB 25 KA, Adj, ICS= 100% ICU - 01 No. SPREADER LINK -01 Set ROH - 01 No. COS, 4P, 100A - 01 No. METERING:- MFM, for V,I,F,PF - 01 No. CT 100/5 -01 Set CT connection link -06 Nos RYB Indicating Lamp LED type 240 V AC -01 Set OUTGOINGS:- FASD STARTER 20 HP : 02 No. Contactor, 3P, 32A -06 Nos O/L Relay (20-33 A) -02 Nos ON - indicator -02 Nos ON/OFF Push button -04 Nos MCB SP 6 A, 10KA -02 Nos Add ON Aux Block, 1NO-1NC -02 Set SPP -02 Nos , Auto mannual selector switch -02 Nos Timer -02 Nos , Wiring with accessories -02 Lot

Supply , laying , connecting, testing and commissioning of 185 Sqmm 3.5 core under ground LT cable XLPE insulated screened, PVC bedded, armoured heavy duty electric cable with stranded aluminium conductor 1100 Volts laid in trenches, fixed to walls/ drawn through pipe and incl the disturbence surface of road making good with using PCC, fixing the cable with suitable size glands, crimping type lugs etc all as specified and directed.

Supply , laying , connecting, testing and commissioning of 95 Sqmm 3.5 core under ground LT cable XLPE insulated screened, PVC bedded, armoured heavy duty electric cable with stranded aluminium conductor 1100 Volts laid in trenches, fixed to walls/ drawn through pipe and incl the disturbence surface of road making good with using PCC, fixing the cable with suitable size glands, crimping type lugs etc all as specified and directed.

M&L for GI tubing light grade 80 mm bore for cable protection laid in trenches/fixed to wall, poles including MS flat iron, clamps,nuts, bolts, etc complete.

Supply and fixing LED street light fittings 60 watt, 230 V AC out door type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp braket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection, average life of street light not less than 50000 hours, inluding clamps, nut, bots, bracket made of GI pipe light grade dia 32mm, length not less than 1.5m, bent to shape for LED fitting for fixing of LED light on electric LT pole including 2 sqmm PVC twin core aluminium cable from conductor to street light not less 2.0 metre , testing to satisfaction of Engineer in charge complete all as specified and directed.