Military Engineer Services Tender

Removing excavated material (Soft/ disintigrated rock) exc 250m but n.exc 500 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

S&F mild steel posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. Note: 1. The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account. 2. Embedded portion of fencing post shall be painted to two coats of tar coal and provision of the same shall be deemed to be including in quoted rate.

All as per item No 05 here-in- before but except material but inclusive of fabrication all as specified and directed.

Dismantling of fencing wire mesh, any type complete all as specified and directed.

Fixing only chain link mild steel galvanised wire fencing of mesh size 100mm x100mm and dia of wire 3mm including 5mm dia GI line wires at top and bottom fixed to any type of standards rails, straining bolts etc including provision of binding wire complete all as specified and directed. Note: 1. The unit rate quoted by contractor is deemed to be inclusive of fixing of ms round bar for line wire and for which supply only rate will be measured and paid separately.

Supply only chain link mild steel galvanised wire fencing of mesh size 100mm x100mm and dia of wire 3mm complete all as specified and directed.

Supply only mild steel round bars 10mm dia and over as in tighting of chain link fencing including cutting to shape, necessary drilling, bolting etc Fe-410-W (Gde E-250) quality -A or Fe 290 (Gde-E-185) complete all as specified and directed.

S&F in repair galvanised, 2 strand, steel barbed wire 2 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts , including,securing or tying at crossings with and Provision of galvanised mild steel wire, staples or steel pins etc. as directed (each line wire to be measured) complete all as specified and directed.

M&L for removal of vegetation growth and bushed etc n'exc 30cm girth including cutting of trunk portion, protruding over ground, diggingout roots, filling holes and levelling off ground, stacking of serviceable materials and removing of unserviceable materials to a distance n'exc 50m and cleaning the site complete all as specified and directed.

Restraining resecuring including making good staples etc galvanised, 2 strand, steel barbed wire 2 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts , including,securing or tying at crossings with and Provision of galvanised mild steel wire, staples or steel pins etc. as directed (each line wire to be measured) complete all as specified and directed.

Dismantling structural steel work including doors, gates any description complete all as directed.

S&F framed work as in iron enclosure, doors or gate of angle iron or other section with gussets plate, rails, braces etc drilled for fixing of steel seating other covering, door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel handing door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and as directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account.

M&L for preparation of new surfaces of steel of any description over 10cm in width or girth applying two coats of synthetic enamel paint over a coat of Red oxide primer complete all as specified.

M&L preparation of old painted steel surfaces of any descripton over 10cm width or girth and applying one coat of synthetic enamel paint of first quality all as specified and directed .

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

M&L for PCC (1:4:8) Type D2 (40 mm graded aggre-gate) as in sub base of floor/ hard standing/ footpath complete all as specified and directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete.

M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregates, as in kerb/ benching/ coping, bed plates, for fixing of hold fast, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L for factory made kerb stone (300mm x 450mm x 150mm) of M-25 grade cement concrete in position to the required line, level and curvature, jounted with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of jounts except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required with and including taking down old kerb stone complete all as specified and directed.

Preparation of newly previously untreated concrete surface of any descroption surfaces exc. 10 cm width or girth and applying two coat of synthetic enemelled paint over a coat of primer incl all preparation complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with old size full brick subclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

Description same all as item No. 25 above but except brick complete all as specified and directed. Note:- Old retreived serviceable bricks shall be used under this item.

M&L for PCC (1:3:6) type C0 (12.5 mm graded stone aggregate) as in coping, roof kerb, cill, bed block, block for insertion of hold fast of door and window with and including formwork complete all as specified and directed.

M&L for Rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete walls surfaces finished even & smooth without using extra cement all as specified and directed.

M&L for preparing old decorated plastered surfaces of wall by complete removal and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed. Note :- The old plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted.

M&L for preparing newly plastered surfaces of wall and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed. Note :- The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted.