Military Engineer Services Tender

M&L for cement concrete type C1 (1:3:6) 20 mm graded stone aggregate as bonders (for stone walling) and setting the block slab etc in cement mortar 1:6) complete all as specified.

M & L for Rendering 15 mm thick in CM 1:4 on fair faces brick or concrete surfaces and finishing surfaces even & fair complete all as specified and directed.

M & L for plain cement concrete Type B-2(1:2:4) (using 12.5 mm graded stone aggregate), cills, steps, parapets , copings, bound stone, bed plates, hold fast and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

Extra over stone walling for hammer dressing to faces of stone and dressing of faced beds and joints as specified for RR walling uncoursed or brought upto courses hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc. 40mm for lime or sand stone complete all as specified and directed.

M&L for raised pointing to RR or Polygon rubble uncoursed or brought upto course in cement mortar 1:4 complete all as specified and directed.

110mm PVC (SWR) pipes single socketed, in any length as in weep holes with rubber ring joints, laid in trenches or in floors, complete all as specified and dir.

Excavating in post holes (or similar holes) in soft/disintegrated rock each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

M&L 5 mm MS plates (plain or cqequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conferming to Fe 410-W (Gde-E-250 quality A) complete all as directed.

S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as directed.

M&L for applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surface & applying one coat of red oxide, zinc chrome complete all as directed.

M & L Plain Cement Concrete type C-2, 1:3:6 (using 40 mm graded stone agg) in foundations, columns,pillars,boundary pillars and posts concrete complete all as specified and directed.

S&F Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws Complete all as specified and directed.

Taking down Chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each complete all as specified and directed.

S & F 30 mm thick moulded door shutter WPC factory made 1005 solid door shutter (confirming as per IS :4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with wood grain texture and back side plain with density not less than 600 kg / cum manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire retardant and having screw holding capacity complete all as specified and directed.

S&F Factory made single riveted WPC (wood polymer composite) solid door frames/chowkat of size 65x100mm of virgin PVC Polymer of K value 58-60(Suspension Grade) calcium carbonate and natural fibres (wood/powder/rice husk/wheat husk ) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threated star heads SS screw having minimum frame density of 750 kg/cum screw withdrawal strenght of 2200 N (face) and 1100 N (Edge)proof, water/moisture proo, minimum compressive strenght of 58 N/mm2, modules of elasticity 900 N/mm2 and serestance to spread of flame of Class A category with property of being termite/borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S & F 300mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified.

S & F 150mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified.

S & F Aluminium handles cast type anodised of size 150mm long ISI marked complete all as specified.

S & F Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in hard / dense soil complete all as specified.

Material & Labour for cement concrete type 1:4:8 (40 mm graded) in foundation, filling and mass concrete all as specified and directed.

M & L 25 mm thick sand filling under paver block incl watering & consolidation complete all as specified and directed.

M & L for Machine pressed precast cement concrete Interlocking paver block any shape and size conforming to IS 15658-2006 of 60 mm thick M-35 grade (ISI Marked) with grey cement and pigment finished with coloured rubber finish on top finished complete all as specified and directed.

Removing excavated mateial exc 250 m but n. exc 500 and depositing where directed at a level n exc 1.5 m above the starting point of soils complete all as specified and directed.