Military Engineer Services Tender

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm, any type of soil, complete all as specified and as directed.

Removing excavated soil not exceeding 50mtr and depositing where directed at a level not exceeding 1.50 mtr above the starting point, complete all as specified and as directed.

Cutting the road depth up to 1.50mtrs below the ground the level and making trench of suitable width to laying 80mm bore galvanised pipe across the cross-section of the road I horizontally for passing electric cable including making good to road surface as per existing specifications or with plain cement concrete M-20 (1:1.5:3), type B-1 (using 20mm graded crushed stone aggregates), complete all as specified and as directed. Note: Cost of cutting the road, laying electric cable through galvanised iron pipe and material required for making good to road surfaces, shall be deemed included in the quoted rate.

Plain cement concrete M-10(1:3:6), type C-2 (using 40mm graded crushed stone aggregate), as mass concrete in foundation, or in foundation of poles and stays, complete all as specified and as directed.

Tubes, 'medium grade' galvanised, 80mm bore, ISI marked including all fitting such as bends, socket, connectors, back nuts, etc, laid in trenches or under floors, complete all as specified and as directed.

Double wall corrugated HDPE pipe, orange colour, ISI marked, nominal size 90mm dia with 75mm inner dia, conforming to IS: 16205 Part-24, including connecting accessories i.e couplers, connectors, bends, sockets, for protection of electric cable, laying in trenches, duct or fixed to walls/ poles as required, complete all as specified and as directed.

Replacement of old unserviceable/ damaged LT XLPE cable with new XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 Volts grade, cross-sectional area 95.0 Sqmm, 3.50-core, laid in trenches or passing through pipes, including suitable lugs and accessories for making connections at both ends, complete all as specified and as directed. Make: Prince/ Finolex/ Astral/ RC Plasto

Supply installation, commissioning, new LT feeder pillar box/ panel, in-replacement of old unserviceable LT panel/ feeder pillar box, complete all as specified and as directed by Engineer-In-Charge. Note: Detailed description and accessories/ equipments shall be as mentioned on serial page No- 23 of tender (CA) here-in-after.

Arial bunched cable, 1100 KV, nominal cross sectional area 35.0 Sqmm, consisting four single core (Four Phase and one Neutral), sizes 4x35Sqmm+25Sqmm, each core screened by an extruded, semi-conducting cable, XLPE insulated and screened again by semi-conducting layer and aluminium tape and XLPE insulation, phase identification tape, twisted around one bared ACSR conductor as messenger made out of aluminium and mild steel alloy and over all PVC or polythene sheathed, stretching the cable on existing poles with mild steel anchor clamps, suspension, clamps, hooks, nuts, bolts and washers including cable ends/ straight through joints (in-line connectors), tee junctions as required at site, complete all as specified and as directed. Make: Havells/ Poycab/ Finolex/ Paragon/ Grandley.

Factory made junction box, made with thermo polycarbonate, weather, water and vermin proof, having IP-65 protection, dust proof, for outdoor use, having internal dimensions 195mmx140mmx65mm, suitable for road/ street lighting for 3-phase/ 4-core high wattage LED based lighting system for industrial applications, suitable for pole mounting, including 01 No. MCB single pole, 6 Amps and 04 Nos. aluminium bus bars of 200 Amps rating duly drilled holes for connections, cable glands, clamps etc for making necessary connections having openable door with locking arrangement, including mild steel iron flat size 25x4mm having holes, nuts, bolts, washers, for fixing/ mounting on poles, painted with two coats of synthetic enamel paint over one coat of primer on internal and external surfaces, fixing in repairs, complete all as specified and directed.

Dismantling insulators any type, any size, complete all as specified and directed.

Dismantling cross-arms of Mild Steel channel or angle sections etc. complete and setting aside and depositing in MES store for re-use in same of new work, complete all as specified and as directed.

Dismantling or taking down of ACSR conductors, setting aside and depositing in MES store for re-use in other work, complete all as specified and as directed

Earthing complete with galvanised iron earth plate electrode 600x600x6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of earth plate not less than 1.5mtr below normal ground level, connected with galvanised iron strip, size 32x6mm as earth lead, by means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 40mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15, type B-1 in pit with precast RCC M-15(1:2:4), type B-1 (using 20mm graded crushed stone aggregates) in cover reinforced with XPM not less than 4.0 Kg per Sqm, test point etc. all as shown in electric plate No-3 of SSR Part-I (2009), complete with necessary earth work in any type of soil, removal to a distance not exceeding 50mtr, including testing on completion, complete all as specified and as directed by Engineer-In-Charge. Note: Earth pit chamber and RCC pit cover shall be painted with two coats of red synthetic enamel paint over one coat of primer including preparing of surfaces.

Replacement of old unserviceable/ damaged LT XLPE cable with new XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 Volts grade, cross-sectional area 10.0 Sqmm, 2.0-core, laid in trenches or passing through pipes, including suitable lugs and accessories for making connections at both ends, complete all as specified and as directed.

Steel tubular swaged poles complete with mild steel base plate, finial taper plug, bolts, nuts and screws as specified, type-410, SP-31 (9.00 meters long), including painting with two coats of aluminium paint over one coat of zinc chrome primer after preparing the exposed surface and two coats of bitumiunous paint on embedded surfaces, complete all as specified and as directed. Note: Excavation, earth work and concrete in foundation shall be measured and paid separately under respective items of BOQ.

Excavation in trenches, not exceeding 1.50mtr wide and exceeding 1.50mtr but not exceeding 3.00mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 3.00 mtr in depth and getting out, in any type of soil, complete all as specified and as directed.

Sand cushioning to protection of underground cables, laid 8 Cm before laying and 15 Cm after laying of cable, and punned to form an overall layer of 18 Cm thick, complete all as specified and directed. Note: Punned thickness shall be measured.

Sub class ‘B’ bricks, modular size, brick covering laid dry, flat, transversally along the length of cable on sand cushioning for mechanical protection of cable, with width equal to the length of the brick, complete all as specified and directed.

Plain cement concrete M-7.50 (1:4:8), type D-2 (using 40mm graded crushed stone aggregate), as in or as mass concrete in foundation of poles/ stays etc, complete all as specified and as directed.

Plain cement concrete M-15 (1:2:4), type B-1 (using 20mm graded crushed stone aggregate), as in coping of pole's foundation including necessary form work, finish even and smooth without using extra cement, complete all as specified and as directed.

LED street light fitting 35 Watt 230 Volt, AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, connecting up with three core flexible copper conductor cable of suitable size, and including house service bracket for mounting light fittings House service bracket any type complete with 1.50mtr long galvanised iron pipe 40mm dia medium grade, bent to required shape including mild steel clamps of flat iron 40x6mm, hook, stay, nut, bolt and washer including painting with two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed. Make: Phillips cat part No- BRP030 P LED35 CW SLR GR PSU SPD or equivalent in Havells/ Bajaj/ Crompton.

Digital Time Switch (Timer), weekly programmable suitable for operating voltage 240 Volts, AC, 50Hz, 16 A contact, complete all as specified and as directed. Make: ABB cat part No- 2CSM208151R1000 or equivalent in L&T/ Merlin Gerin/ Siemens.

Factory made junction box, made with thermo polycarbonate, weather, water and vermin proof, dust proof, for outdoor use, having internal dimensions 250mmx150mmx100mm, suitable for road/ street lighting for 3-phase/ 4-core high wattage LED based lighting system for industrial applications, suitable for pole mounting, including 01 No. MCB single pole, 6 Amps and 03 Nos. aluminium bus bars of 100 Amps rating duly drilled holes for connections, cable glands, clamps etc for making necessary connections along with locking arrangement, including mild steel iron flat size 25x4mm having holes, nuts, bolts, washers, for fixing/ mounting on poles, painted with two coats of synthetic enamel paint over one coat of primer on internal and external surfaces, fixing in repairs, complete all as specified and directed.

Sub main wiring for circuits/ submain wiring alongwith earth wire with two run of 2.50 Sqmm of fire resistance, PVC insulated copper conductor, single core cable, multi-stranded, FRLS, ISI marked, 1100 Volts grade and one run of 2.50 Sqmm, FRLS, PVC insulated copper conductor, single core cable, multi stranded, ISI marked, 1100 Volts grade as earth wire connected to earth terminal, drawn in and including metallic medium grade rigid conduit, fire resistance, ISI marked, 20mm dia including all accessories, fixed on swaged pole surface alongwith mild steel clamps, complete all as specified and as directed.

MCCB, four pole, 415 Volts, adjustable thermal and fixed magnetic setting, 40 Amps with breaking capacity 16 KA, having indicating lamp, Ics=100% and Icu as per IEC 60947-2, complete all as specified and as directed. Make: Schneider cat part No- C11E6TM040B equivalent in L&T/ Legrand/ Merlin Gerin/ Siemens/ ABB.

Tubes, 'medium grade' galvanised, 15mm bore, ISI marked including all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc, fixed on walls or floors, complete all as specified and as directed. Note: Cost of cutting/ chasing and the making good to the surfaces shall be deemed included in qupoted rate.

Bib taps, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

Angle/ Stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

Point wiring (in existing concealed/ exposed conduits to surfaces) or in casing and caping for 3-pin, 15/ 16 Amps, switch socket combination on independent board with two run of 2.50 Sqmm, PVC insulated, unsheathed, single core, multi-stranded, copper conductor cable, FRLS, 1100 Volts, using colour coding, drawn in and including any type of conduit/ new casing and caping, any size/ dia including all accessories concealed by chasing/ cutting or fixed with PVC plug and mild steel screws on the surface of walls/ floors/ ceilings and making good the disturbed surface matching to existing descriptions/ specifications, with and including sunken type pressed steel/ welded mild steel terminal box 1.20mm thick coated with anti corrosive paint with bakelite laminated sheet top cover 3.0mm thick and including FRLS PVC green insulated unsheathed 2.50 Sqmm copper earth continuity wire connected to earth dolly, complete all as specified and as directed.

Switch piano, flush type, single pole, one way, 15/ 16 Amps, complete all as specified and as directed.

Socket outlet, 2-in-1, 3-pin, 5/ 6 and 15/ 16 Amps, combined, flush type, complete all as specified and as directed.

Water heater storage type (geyser), wall hanging, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5-Star rated, single-phase, 50 Hz AC, energy saving high density PUF insulation, complete with all accessories such as safety valve, thermostate, NRV, etc, complete all as specified. Make: Havells cat part No- GHWAPPTWB025 or as equivalent in Bajaj/ Jaquar/ Crompton.

Ceiling fan, metallic, sweep 1200mm, minimum air delivery 210CFM with service value 6.00BEE, five star rating for energy saving, copper wounded brush less direct current (BLDC) motor along with remote control including electronic fan regulator and hanging accessories i.e. U-clamp, down rod, canopy and nut bolts, washers, complete all as specified and as directed. Make: Crompton Greaves model- Energion HS or as equivalent in Havells/ Usha/ Bajaj/ Orient.

PVC connections 15mm size with brass nuts, of length 450mm, fleible and braided with mild steel wire, complete all as specified and as directed.

Earthing complete with galvanised iron earth plate electrode 600x600x6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of earth plate not less than 1.5mtr below normal ground level, connected with galvanised iron wire, size 4.0mm dia as earth lead, by means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 20mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15, type B-1 in pit with precast RCC M-15(1:2:4), type B-1 (using 20mm graded crushed stone aggregates) in cover reinforced with XPM not less than 4.0 Kg per Sqm, test point etc. all as shown in electric plate No-3 of SSR Part-I (2009), complete with necessary earth work in any type of soil, removal to a distance not exceeding 50mtr, including testing on completion, complete all as specified and as directed by Engineer-In-Charge. Note: Earth pit chamber and RCC pit cover shall be painted with two coats of red synthetic enamel paint over one coat of primer including preparing of surfaces.

Amount of Schedule of credit of for Rs 61,700.00 shall be deducted from quoted amount.