Uttar Pradesh Rajkiya Nirman Nigam Tender

Double bed for satelite catering/ Player living Supplying and placing decorative design double bed with an overall size 1560mm (L)X 2060mm (W) X 900mm/400mm. The bed shall be made of Pre-laminated particle board of grade II of IS 12823 with approved laminate and shade. The head and leg shall be made of 18mm thick particle board and also plingth of 18mm thick particle board. The edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel with the assistance of edge banding machine at 200 degree celsius. The side cladd with 18mm thick particle board with 2mm PVC edge banding at upper side and 0.8mm thick edge banding al bottom side. Mattress panel shall be made up of 18mm thick particle board. The bed shall have openable under storage through mattress panel. The understructure shall consist of MS/CRCA powder coated pipe frame with 1.5mm thick. The base shall be used 12mm thick particlde board. There shall be nylon shoe provided at the base to avoid scratches on the floor of maintain uneven surface. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Sofa 1 seater for Judge's lobby Supplying and placing single seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The armrest shall be flap with soft cushion on both side for aesthetically appealing as well as side comfort. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall consist of MS powder coated frame having thickness 8mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 500±10 mm(W) X 530±10 mm (D) X 380±10 mm (H). Overall width = 1020±10 mm, overall depth = 830±10 mm & overall height = 860±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Sofa 2 seater for resting room/ Judge's waiting/ Waiting Supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The armrest shall be flap with soft cushion on both side for aesthetically appealing as well as side comfort. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have MS powder coated frame having thickness 8mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 980±10 mm(W) X 530±10 mm (D) X 380±10 mm (H). Overall width = 1525±10 mm, overall depth = 830±10 mm & overall height = 860±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Sofa 3 seater for Mixed Zone/ Waiting/ Conference room/ Ticket office/ Tech. office lounge/ Athelete changing Supplying and placing a three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The armrest shall be flap with soft cushion on both side for aesthetically appealing as well as side comfort. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have MS powder coated frame having thickness 8mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 1460±10 mm(W) X 530±10 mm (D) X 380±10 mm (H). Overall width = 2030±10 mm, overall depth = 830±10 mm & overall height = 860±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Centre table for resting room/ Judge's waiting/ Mixed Zone/ Waiting/ Conference room/ Ticket office/ Tech. office lounge Supplying & placing center table with an overall size 1200mm X 600mm X 450mm. The top shall be made up of 12mm thick toughened glass. The top profile shall be in rectangle shape with bevelled edges. The understructure shall consist of MS/CRCA rectangle pipe frame having cross-section area 30mm X 15mm with 1.6mm thick duly powder coated with 50-60µ dy film thickness. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Table for common wealth sports federation/ National federation office/ Organising committee office/ Tech. office lounge Supplying & Placing executive table with credenza unit and pedestal in completely knock down conditions with an overall size 2400mm X 2300mm X 750mm that is to be assembled at site. The worktop shall be 43mm thick having the combination of 18mm Pre-laminated particle board with approved laminate and shade as top and 25mm Medium density fibre-board as base top. The worktop shall have the size 2400mm X 1100mm having the profile in rectangle shape and the edges (top) shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius and deco paint with half round post form edges along with grooves (base top). The top shall be supported on 4 nos. of SS pipe strips having size 230mm X 60mm X 15mm. The table shall be clad with 48mm thick modesty panel which provide structural support for the table. It should be 48mm thick Pre-laminated particle board in linear shape with appropriate PVC edge banding and shall be cladded with SS pipe frame on sides having cross-section area 95mm X 25mm. The understructure shall consist of SS 202 grade loop leg having cross-section area 95mm X 25mm. There shall be buffers provided to avoid to avoid scratches on the floor as well as uneven surfacing. The credenza unit shall have the size 1600mm x 500mm X 670mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with top 25mm thick, drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 7 drawer and operated with the assistance of SS handle and easily close & open with roller channel ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The credenza unit shall be mounted on SS 202 grade loop leg having cross-sectional area 95mm X 25mm. Pedestal shall be provided with an overall size 400mm X 500mm X 660mm. It should be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, facia shall be 18mm thick & drawer base shall be 9mm thick. It shall have 3 nos. of drawer having same size and operated with SS handle and easily close & open with the assistance of roller and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be locked with one single key. The pedestal shall be mounted on injection moulded nylon castor. The Bidder/ Bidder/ manufacturer/ OEM shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Chair high back for common wealth sports federation/ National Federation office/ Organising committee office/ Tech. office lounge Providing and supplying high back chair with ergonomic design for user comfort. The seat and back shall be made of hot pressed commercial plywood and wooden frame padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GMS. The backrest of the chair shall be made by keeping the natural curvature of the spine for lumbar support as well as head support. The armrest shall be used cushion arm with leatherite covering top mounted on injection moulded ABS chrome holder. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustement. The pneumatic seat height adjustment for healthy seating user can adjust seat height up to 65mm with BIFMA standard class 3 gas-lift to suite them using the lever under the seat. The gas-lift mechanism should be tested as per BIFMA X5.1-2011 standard. The pedestal should have five legged die casted aluminium having pitch circle dia. 700mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 500±10 mm(W) X 500±10 mm(D) and back size shall be 500±10 mm(W) X 775±10 mm(H) from seat & overall height = 1180±10 mm, overall width (arm) = 630±10 mm & overall depth = 700±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Chair mid back for common wealth sports federation/ National federation office/ Organising committee office/ Tech. office loung Providing and supplying medium back chair with ergonomic design for user comfort. The seat and back shall be made of hot pressed commercial plywood and wooden frame padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GMS. The backrest of the chair shall be made by keeping the natural curvature of the spine for lumbar support. The armrest shall be used cushion arm with leatherite covering top mounted on injection moulded ABS chrome holder. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustement. The pneumatic seat height adjustment for healthy seating user can adjust seat height up to 65mm with BIFMA standard class 3 gas-lift to suite them using the lever under the seat. The gas-lift mechanism should be tested as per BIFMA X5.1-2011 standard. The pedestal should have five legged die casted aluminium having pitch circle dia. 700mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 500±10 mm(W) X 500±10 mm(D) and back size shall be 500±10 mm(W) X ±10 mm(H) from seat & overall height = ±10 mm, overall width (arm) = 630±10 mm & overall depth = 700±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Workstation/ Ticket office/ Control room Providing and placing workstation table in completely knock down conditions with an overall size 1320mm X 660mm X 1200mm that is to be assembled at site. The work top shall have the size 1200mm X 600mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 525mm X 350mm. The trey shall be operated on keyboard channel. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in the front side of user as well as on the both sides of the user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with 40µ-60µ thick. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways & 4 ways (L-cover for corner, T-cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) and marker board provided at front of the user. Laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. Fixed type pedestal shall be provided with an overall size 400mm X 450mm X 725mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized lock with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A nylon castor based CPU unit shall be provided with an overall size 468mm X 284mm with 18mm thick Pre-laminated particle board. The Bidder/ Bidder/ manufacturer/ OEM shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Workstation for broadcast/ Organisation committee/Tech. operation/ Satellite catering/ sports federation/ Telephone booth/ Mobile communication Supplying & Placing workstation table in completely knock down conditions with an overall size 1560mm X 1560mm X 1200mm that is to be assembled at site. The worktop shall have the size 1500mm/600mm X 1500mm/600mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in curvilinear shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on particle board base gable end. The end wall of the top shall be topped by gable end. It should be made up of 25mm thick Pre-laminated particle board and the profile shall be in linear shape with appropriate PVC edge banding. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in front side of user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with 40-60µ thick. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways & 4 ways (L-cover for corner, T-cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) provided at front of the user. Laminated bottom tile shall be situated below the work top. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. Mobile pedestal shall be provided with an overall size 400mm X 450mm X 680mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted on injection moulded nylon castor. A nylon castor based CPU unit shall be provided with an overall size 470mm X 286mm with 18mm thick Pre-laminated particle board. The Bidder/ Bidder/ manufacturer/ OEM shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Chair for Workstation for broadcast/ Organisation committee/Tech. operation/ Satellite Catering/ sports federation/ Telephone booth/ Mobile communication Providing and supplying mid back chair. The seat shall be made of 15mm thick hot pressed commercial plywood upholstered with high resiliance polyurethane foam 40mm thick having density 40kg/m³ with fabric tapestry 0.6mm thick and 235 GSM and the back shall be made of two piece injection moulded polypropylene net cover upholstered with breathable mesh tapestry. The armrest of the chair shall be used polypropylene arm completely joint with seat & back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 120mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged injection moulded in black nylon having pitch circle Dia. 650 mm fitted with 5 nos. twin wheel castor. The castor of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 470±10 mm(W) X 460±10 mm(D) and back size shall be 460±10 mm(H) from seat & overall height = 865±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Sofa 3 seater for common wealth sports federation/ National federation office/ Technical committee office/ Ceremony room/ Organise committee office Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall consist of SS 202 grade leg having Dia. 38mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 540±10 mm(D) X 1540±10 mm(W), seat height = 430±10 mm, overall width = 1920±10 mm, overall depth = 760±10 mm & overall height = 750±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Sofa 1 seater for common wealth sports federation/ National federation office/ Organise committee office Supplying and placing single seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have SS leg with shiny chrome finish having Dia. 38mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 540±10 mm(D) X 480±10 mm(W), seat height = 430±10 mm, overall width = 870±10 mm, overall depth = 760±10 mm & overall height = 750±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Sofa 1 seater for common wealth sports federation/ National federation office/ Organise committee office Supplying and placing single seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have SS leg with shiny chrome finish having Dia. 38mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 540±10 mm(D) X 480±10 mm(W), seat height = 430±10 mm, overall width = 870±10 mm, overall depth = 760±10 mm & overall height = 750±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Conference table for ceremoney room/ Meeting room Supplying & Placing Conference table in completely knock down conditions with an overall size 3600mm X 1200mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix, dowels, pins and brackets. The worktop shall have the combination of PLPB board and MDF board. The main top should be made up of back to back 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and the base top shall be made up of 25mm thick Medium density fibre-board with deco matt finish. The table top profile shall be boat like shape with round corners. The edges edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius and the base top shall be with half round post form with grooves. The table shall be supported on particle board base gable end. The end wall of the table on the side and mid shall be topped by gable end. It should be made up of 36mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick Pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The Bidder/ Bidder/ manufacturer/ OEM shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Supplying & Placing Conference table in completely knock down conditions with an overall size 4500mm X 1500mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix, dowels, pins and brackets. The worktop shall have the combination of PLPB board and MDF board. The main top should be made up of back to back 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and the base top shall be made up of 25mm thick Medium density fibre-board with deco matt finish. The table top profile shall be boat like shape with round corners. The edges edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius and the base top shall be with half round post form with grooves. The table shall be supported on particle board base gable end. The end wall of the table on the side and mid shall be topped by gable end. It should be made up of 36mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick Pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The Bidder/ Bidder/ manufacturer/ OEM shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Conference table for meeting room Supplying & Placing Conference table in completely knock down conditions with an overall size 5400mm X 1500mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix, dowels, pins and brackets. The worktop shall have the combination of PLPB board and MDF board. The main top should be made up of back to back 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and the base top shall be made up of 25mm thick Medium density fibre-board with deco matt finish. The table top profile shall be boat like shape with round corners. The edges edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius and the base top shall be with half round post form with grooves. The table shall be supported on particle board base gable end. The end wall of the table on the side and mid shall be topped by gable end. It should be made up of 36mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick Pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The Bidder/ Bidder/ manufacturer/ OEM shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Conference chair for ceremoney room Providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be supplied with inserted pipe frame. The chair shall be padded with high resilience polyurethane foam 50mm thick having density 40Kg/m³ in seat and 12mm thick having density 23Kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM and breathable mesh tapestry behind the backrest. MS chrome plated pipe frame shall be provided on both side of seat and back with size 25mm X 10mm. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support. The armrest shall be used black integral polyurethane arm mounted on CRCA chrome plated pipe having size 40mm X 10mm completely joint with seat and back with the assistance of Allen key screw. A chrome plated round bend pipe of dia. 9mm shall be provided behind the backrest of the chair and welded with main frame. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal shall have five legged CRCA chrome plated having pitch circle dia. 650mm fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled, confirming to ANSI/BIFMA Standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The Seat size shall be 490±10 mm(W) X 520±10 mm(D) and back size shall be 450±10 mm(W) X 535±10 mm(H) from seat & overall height = 980±10 mm, overall width = 560±10 mm & overall depth = 670±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

4 door PLU for athlete changing Overall size of Personal Locker Unit with add on units shall be of dimensions 380mm(W) X 450mm(D) X 1800mm(H) having 4 locker unit. Stackability shall have add - on units that can be stacked width wise to form bank of lockers having common side panel. Locking shall have cam lock with lock lever plus option. Material shall be CRCA 0.8 mm thickness. Shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum. Finish shall be epoxy polyester powder coated to the thickness of 50 microns. Handle/Label holder shall be aesthetically appealing Snap fit ABS plastic handle. Ventilation shall be attractive punched pattern for ventilation. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Table for international federation office Supplying & installing of table with ERU and pedestal having following specifications. The table shall be supplied in completely knock down conditions with an overall size 2400mm X 2100mm X 750mm that is to be assembled at site. The worktop shall have the size 2200mm X 940mm made up of 50mm thick Medium Density Fibre-board with approved laminate and finish as per approved shade. The top edge should cladded with 1.2mm thick extruded aluminium section all around the worktop and die cast end caps on joints for better strength of the table. The profile shall be in rectangle shape and enclosed by single sided flapper box that houses telephone cable, data and power connection discretely. The top shall be supported on gable end at one side and round peg mounted on ERU unit at another side. The end wall of the table on the side shall be topped by gable end. It should be 50mm thick Medium Density Fibre-board linear in profile and the edges cladd with extruded aluminium profile. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick particle board and shall be linear in profile with round corners and the edges shall be sealed with 0.8mm thick PVC edge banding. The table shall be supplied with credenza unit with an overall size 1980mm X 400mm X 635mm that shall be constructed from Pre-laminated particle board of grade II of IS 12823 with 25mm thick top and other parts 18mm thick like shutter, back, facia etc. It shall have 3 drawers and 2 door shutter. The drawer and shutter shall be operated with ball bearing sliding channel and soft close concealed crank hinge. G-profile Aluminium handle shall be supplied for ease of opening. The ERU unit shall be mounted on 38mm Dia. Aluminium round leg. Fixed pedestal shall be supplied with an overall size 380mm X 400mm X 600mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Top shall be 25mm thick, side, back, facia shall be 15mm thick. The pedestal shall have 2 nos. of drawer having same. The drawer shall be operated with ball bearing sliding channel having load capacity 35Kg to enable smooth operation. Aluminium handle shall be provided for ease of opening. For locking provision central lock mechanism shall be given in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted on Aluminium round leg. The Bidder/ Bidder/ manufacturer/ OEM shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Chair high back for international federation office Providing and supplying high back chair. The seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 45kg/m³ and the back shall be made of bright bar padded with high resilience polyurethane foam 50mm thick having density 45kg/m³. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine with contour lumbar support as well as head support. The seat and back shall be arrested together with mechanism by means of powder coated HR steel spine and armrest shall be used Aluminium PU arm completely joint with seat. For seating durability the chair shall have synchro knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti shock feature. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA standard. The pedestal should have five legged die casted aluminium having pitch circle dia. 700mm fitted with 5 nos. twin wheel castor. The castor of the chair should be injection moulded in black 30% glass filled nylon. The seat size shall be 510±10 mm(W) X 480±10 mm(D) and back size shall be 500±10 mm(W) X 720±10 mm(H) from seat. Overall height shall be = 1225±10 mm, base width/ depth = 760±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Mid back chair for international federation office Providing and supplying mid back chair. The seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 45kg/m³ and the back shall be made of bright bar padded with high resilience polyurethane foam 50mm thick having density 45kg/m³. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine with contour lumbar support. The back shall be arrested together with mechanism by means of powder coated HR steel spine and armrest shall be used Aluminium PU arm completely joint with seat. For seating durability the chair shall have synchro knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti shock feature. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA standard. The pedestal should have five legged die casted aluminium having pitch circle dia. 700mm fitted with 5 nos. twin wheel castor. The castor of the chair should be injection moulded in black 30% glass filled nylon. The seat size shall be 510±10 mm(W) X 460±10 mm(D) and back size shall be 500±10 mm(W) X 580±10 mm(H) from seat. Overall height shall be = 1045±10 mm, base width/ depth = 760±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Sofa 1 seater for international federation office Supplying and placing single seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The armrest shall be flap with soft cushion on both side for aesthetically appealing as well as side comfort. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall consist of MS powder coated frame having thickness 8mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 500±10 mm(W) X 530±10 mm (D) X 380±10 mm (H). Overall width = 1020±10 mm, overall depth = 830±10 mm & overall height = 860±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Centre table for international federation office Supplying & placing center table with an overall size 1200mm X 600mm X 450mm. The top shall be made up of 12mm thick toughened glass. The top profile shall be in rectangle shape with bevelled edges. The understructure shall consist of MS/CRCA rectangle pipe frame having cross-section area 30mm X 15mm with 1.6mm thick duly powder coated with 50-60µ dy film thickness. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Table for technical committee office/ Organising committee office/ Merchandisin Supplying & Placing Modular table in completely knock down conditions with an overall size 1800mm X 1650mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall have the size 1800mm X 750mm made up of 25mm thick particle board with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape with front and back full round post form edges and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The table top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table shall have side unit for storage purpose with an overall size 900mm X 450mm X 750mm. The side unit shall be made up of Pre-laminated particle board of grade II of IS 12823 with top 25mm thick and other parts 18mm thick like shutter, back, side panel etc. It shall have 2 sliding shutter which slides over sliding rail track. The shutter shall be operated with SS handle and Multi-purpose (MP) locking mechanism. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 680mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. A movable type CPU unit shall be provided with an overall size 468mm X 284mm. The CPU unit shall be made up of 18mm thick Pre-laminated particle board and mounted over 65mm injection moulded nylon castor. The Bidder/ Bidder/ manufacturer/ OEM shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

High back chair for technical committee office/ Organising committee office/ Merchandising Providing and supplying high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of hot pressed plywood padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine which helps to provide lumbar support as well as head support. The armrest shall be used cushion arm with leatherite covering top. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged MS/CRCA chrome plated having pitch circle Dia. 700mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA standard X5.1-2011 tested to perform 98,000 cycles with 250lba load. The seat size shall be 480±10 mm(W) X 480±10 mm(D) and back size shall be 475±10 mm(W) X 755±10 mm(H) from seat & overall height = 1200±10 mm, overall depth = 700±10 mm & overall width = 630±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Mid back chair for technical committee office/ Organising committee office/ Merchandising Providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of hot pressed plywood padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine which helps to provide lumbar support. The armrest shall be used cushion arm with leatherite covering top. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged MS/CRCA chrome plated having pitch circle Dia. 650mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA standard X5.1-2011 tested to perform 98,000 cycles with 250lba load. The seat size shall be 490±10 mm(W) X 470±10 mm(D) and back size shall be 490±10 mm(W) X 540±10 mm(H) from seat & overall height = 970±10 mm, overall depth = 710±10 mm & overall width = 645±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Lounge table for Games family lounge/ VIP/ Lounge meeting/ Media lounge/ Food and beverages Supplying and placing cafeteria table with an overall Dia. 800mm X 750mm. The top of the table shall be made of 8mm thick tempered glass with bevelled edges. The top profile shall be in circular shape and supported on Aluminium round spacer mounted on CRCA rectangle pipe frame having cross-section area 30mm X 15mm in Y shape welded together with tubular pipe frame having cross-section area 40mm X 20mm with 1.6mm thick in circular shape. The understructure shall consist of 3 nos. of legs made up of MS/CRCA. The complete metal structure shall be supplied with 50-60µ thick powder coated and chrome plated. There shall be plastic shoe provided at the base to avoid scratches on the floor. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Lounge chair for Games family lounge/ VIP/ Lounge meeting/ Media lounge/ Food & beverages Providing and supplying plastic shell chair. The seat and back shall be made up of injection moulded high impact strength polypropylene polymer. The understructure shall consist of MS/CRCA round pipe frame having dia. 22.2mm with 1.6mm thick and 35mmX15mm capsule pipe with 1.6mm thick. It should be powder coated to the thickness of 40-60µ DFT. There shall be plastic show provided at the bottom. The overall size of the chair shall be 840mm(H) X 520mm(W) X 530mm(D). The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

3 seater waiting chair for lobby Providing and supplying 3 seater visitor chair with 4 arms. The seat and back shall be made up of reinforced PU foam with MS perforated sheet. The seat mounted on MS powder coated rectangular cross beam having cross-section area 60mm X 60mm fitted with polypropylene end caps on both side. The arm and leg shall be made up of pressure diecast aluminium. there shall be leceller shoe provided at the bottom with metal insert. The individual seat size shall be 515±10 mm(W) X 467±10 mm(D), Back size shall be 515±10 mm(W) X 510mm±10 mm(H) from seat, Overall width shall be = 1640±10 mm, overall depth = 680±10 mm, overall height = 860±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Table for team cabin Supplying & Placing cafeteria table with an overall size 1800mm X 900mm X 750mm. The top shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS/CRCA rectangle pipe frame having cross-section area 70mm X 20mm with 1.6mm thick. The understructure shall consist of four legs made up of MS round pipe having dia. 38.1mm with 1.6mm thick. The Joints shall be made using TIG welding. The metal parts shall be powder coated to dry film thickness of 40-60µ. There shall be PPCP shoe provided at bottom to avoid scratches on the floor. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Chair for team cabin Providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle Dia. 650±15 mm and fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 460±10 mm(W) X 450±10 mm(D) and back size shall be 460±10 mm(W) X 400±10 mm(H) from seat. Seat height = 460±10 mm, overall height shall be = 810±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Table for doctor room Supplying & Placing executive table with credenza unit in completely knock down conditions with an overall size 1800mm X 1800mm X 750mm that is to be assembled at site. The worktop shall have the size 1500mm X 900mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on CRCA rectangle pipe frame having cross-section area 40mm X 20m with 1.6mm thick duly powder coated. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick Pre-laminated particle board in linear shape with appropriate PVC edge banding. The table understructure shall consist of CRCA rectangle pipe leg (loop leg) and (U-type leg) having cross-section area 40mm X 10mm and 95mm X 25mm with 1.6mm thick. There shall be shoe provided at the base to avoid scratches on the floor. The table shall have credenza unit for storage purpose with an overall size 1800mm X 580mm X 430mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 3 drawer and 1 sliding shutter which is operated on ball bearing channel to enable smooth operation, SS handle and central locking mechanism in which all the drawer shall be synchronized locked with one single key. The credenza unit shall be mounted on CRCA rectangle pipe frame leg having cross-section area 40mm X 10mm with 1.5mm thick. The complete metal parts shall be duly powder coated to the thickness 50-60µ dry film thickness. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The Bidder/ Bidder/ manufacturer/ OEM shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

High back chair for doctor room Providing and supplying high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 45kg/m³ in seat and 45mm thick having density 35Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene/ABS moulded cover and the backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used black integral polyurethane arm with metal insert completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700±15 mm and fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA Standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 485±10 mm(W) X 450±10 mm(D) and back size shall be 490±10 mm(W) X 610±10 mm(H) from seat. Seat height 460±10 mm, overall height shall be 1060±10 mm, overall depth = 620±10 mm and overall width (Arm) = 600±10 mm, Overall base dia. 760±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Revolving chair for doctor room Providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 45kg/m³ in seat and 45mm thick having density 35Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene/ABS moulded cover and the backrest shall be made by keeping the natural curvature of the spine with back support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used black integral polyurethane arm with metal insert completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle Dia. 650±15 mm and fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 485±10 mm(W) X 450±10 mm(D) and back size shall be 480±10 mm(W) X 400±10 mm(H) from seat. Overall height shall be 710±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Examination table Overall dimension - 1830mm L X 560mm W X 810mm H Two section top with fix mattress Backrest movement on rachet Pretreated and powder coated The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Bed for physiotherapy/ First aid medical treatment Basic bed has the flat platform Overall dimension - 1800mm L X 900mm W X 510mm H MS head and foot panel of unequal height Pre-treated and epoxy powder coated finish The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Sofa set for VIP rest room/ Merchandising/ Satelite catering/ Player living Supplying and placing sofa set (3+1+1) that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The complete structure shall be fully upholstered with leatherite tapestry 1±0.2 mm thick and 571 GSM. The understructure shall be supported by pipe frame leg of SS shiny chrome finish having length 875mm and height 100mm with cross-section area 67mm X 13mm. There shall be shoe provided at the bottom to avoid scratches on the floor. overall width(3 seater) = 2110±10 mm, overall width (1 seater) = 920±10 mm, overall depth = 965±10 mm & overall height = 825±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Centre table for VIP rest room/ Merchandising/ Player living Providing and supplying centre table with an overall size 1200mm X 600mm X 430mm. The top and side cladding shall be made up of 36mm thick pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. Extruded aluminium section shall be inserted within side corner edge at both side of the table. There shall be leveller shoe provided at the bottom. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Arc C type sofa for VIP rest room/ Competition office Supplying and placing arc sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The profile of the sofa shall be in C-type Arc shape. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. The seat and back shall be upholstered with fabric tapestry. The under structure shall have MS chrome plated leg having length 70mm and Dia. 30mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 530±10 mm(D), seat height = 425±10 mm, overall width = 2650±10 mm, overall depth = 690±10 mm & overall height = 700±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Reception table/ Sponser showcase/ Merchandising Supplying & Placing Reception table in completely knock down conditions with an overall size 2400mm X 820mm X 1000mm that is to be assembled at site. The top shall have the size 2300mm X 695mm made up of 49mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The upper top shall have the size 1400mm X 300mm with 49mm thick. The top profile shall be in rectangle shape with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The side edges shall be covered with die casted aluminium profile. The table top and upper top shall be supported on particle board base strip. The table shall have a front panel having size 1390mm X 750mm with 49mm thick Pre-laminated particle board. A wire manager cap shall be provided on the top of the table for power connection. The end wall of the table on the side shall be topped by gable end. It shall be made up of 49mm thick Pre-laminated particle board and profile shall be in linear shape with one clipped corner and covered by Aluminium profile. There shall be buffers provided to avoid the scratches on the floor. The table shall be clad with 49mm thick modesty panel which provide structural support for the table. It should be 49mm thick pre-laminated particle board in linear shape with appropriate PVC edge banding and covered by aluminum profile connected with both end. The Bidder/ Bidder/ manufacturer/ OEM shall have basic quality and safety certifications like ISO-9001:2015, ISO-14001: 2015, ISO-18001:2007, BIFMA Membership & AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Reception chair/ Sponser showcase/ Merchandising Providing and supplying mid back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood upholstered with high resilience moulded polyurethane foam 50mm thick having density 50kg/m³ with fabric tapestry 0.6mm thick and 235 GSM and the back shall be made of metal bright bar upholstered with breathable mesh tapestry. The backrest of the chair shall be made by keeping the natural curvature of the spine with cushion base lumbar support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used injection moulded polypropylene loop arm completely joint with seat. For seating durability the chair shall have push back 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged injection moulded in 30% glass filled black nylon having pitch circle Dia. 650 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 460±10 mm(W) X 455±10 mm(D) and back size shall be 550±10 mm(H) from seat & overall height = 990±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Table for resource centre/ Merchandising/ Venue operation/ communication/ Workforce briefing/ Security/ Tech. deligate/ International federation Supplying & Placing Modular table in completely knock down conditions with an overall size 2000mm X 900mm X 750mm that is to be assembled at site. The worktop shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. The table shall be supported over SS pipe leg 202 grade having cross-section area 80mm X 20mm. There shall be buffers provided to avoid scratches on the floor. The Bidder/ Bidder/ manufacturer/ OEM shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Chair for resource centre/ Merchandising/ Venue operation/ communication/ Workforce briefing/ Security/ Tech. deligate/ International federation Providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 45kg/m³ in seat and 45mm thick having density 35Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene/ABS moulded cover and the backrest shall be made by keeping the natural curvature of the spine with back support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used black integral polyurethane arm with metal insert completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle Dia. 650±15 mm and fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 485±10 mm(W) X 450±10 mm(D) and back size shall be 480±10 mm(W) X 400±10 mm(H) from seat. Overall height shall be 710±10 mm. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Steel almirah Providing, supplying and placing steel almirah in perfectly upright and straight position. The overall size of the almirah shall be 915mm (W) X 485mm (D) X 1980mm (H) including legs. It should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. Door shall be made of 1mm thick and all other components shall be made of 0.8mm thick high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. Stiffeners shall be provided in shelf & door. The steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity per each shelf shall be 40kg maximum. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 50-60µ. The product should be approved make of Haworth/ Steelcase/ Godrej/ featherlite/ Veils as per the direction of Architect or Engineer-Incharge.

Stadium Chair

Providing and fixing spectator/vistor chair for arena area

Providing and fixing player chair for arena area

Providing and fixing VIP / Media chair for arena area