Uttar Pradesh Housing And Development Board Tender
... More
If you're a registered bidder for etender UP and want to inquire about any e-tender UP government has posted, this is your stop. No need to enter every detail on the website of etender.up.nic.in - BidAssist filters will help you find the exact UP etender you're looking for. Read to learn how to search & bid for etender UP.
Uttar Pradesh Housing And Development Board - UPAVP Tender
Civil And Construction
Building Construction
Electrical and Electronics
Eprocure
Opening Date2 May 2025
Closing Date31 May 2025
Tender Amount₹ 4,58,16,634
Technical
Technical
Additional Eligibility
Class Of Bidder
... View More
Class- as per Applicable or Above, in Relevant category.
Technical Capacity
... View More
The required prior work experience for the bidder is that they should have appropriate experience in similar work for the last Seven years in the organised sector. The experience requirements are as follows:
- One similar completed work costing not less than 80% of the estimated cost
- Two similar completed works costing not less than 50% of the estimated cost
- Three similar completed works costing not less than 40% of the estimated cost. Additionally, the bidder should have an average annual financial turnover during the last three years ending 31 March 2025 of at least 30% of the estimated cost. The liquid assets required is 15% of the bid amount, and the bidder should have a minimum turnover of 30% of the estimated cost. The similar work means Civil construction work, and evidence of satisfactory execution of work that has been executed by the tenderer during the last Seven years in the organised sector has to be produced. The certificate of experience from the Engineer-in-charge of the work, not below the rank of Executive Engineer, shall be considered acceptable in Govt./Semi Govt. organisations.
Costs
EMD
₹ 9,17,000Document Cost
₹ 7,080Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2025_UPHDB_1035427_1Tender No
679/AC-9/22 DATE 228.04.2025 (1)Tender Authority
Uttar Pradesh Housing And Development Board ViewPurchaser Address
-Website
http://etender.up.nic.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 15 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand).DSR6.1.1
51.23
3944
202081.86
... More
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)(DSR-4.1.8)
160.81
4960
797622.42
... More
1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)(DSR-4.1.3)
0.63
5717
3601.75
... More
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). DSR 5.3
113.77
8377
953109.31
... More
15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)13.5.1
1053.91
298
314897.77
... More
P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. DSR-5.22.6
89.31
7852
701341.61
... More
Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. all kinds of soil.DSR 2.28.1
13700
24
340719
... More
Brick work with bricks of class designation 15 (Class-150) in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand (FM 1.50 to 2.00)).AR
158.53
6935
1099495.91
... More
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-lll) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources).DSR 4.1.3
5.23
5736
30002.31
... More
Mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods,gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. (Gril).DSR 10.25.1
519.75
89
46735.92
... More
Painting two coat over priming coat (but including cost of priming coat) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3,Hi-gloss apcolite superlac, DULUX specified brushing to give an even shade and including cleaning the surface of all dirt,dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work.DSR 13.48.3
233.1
124
28972
... More
Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4 mm.(DSR - 16.70.1)
303
741
224550.27
... More
Extra for excavating trenches for pipes, cables, etc. in ordinary/hard rock exceeding 1.5 m in depth but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre),Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia (DSR-2.14.1.1)
525
531
278979.75
... More
Chain link fabric fencing mesh of size 50x50 mm made of G.I. wire of dia 4 mm, PVC coated to outer dia 5 mm. (DSR BASIC ITEM-8696)
1487.4
264
393134.69
... More
Providing and laying 140mm dia, HDPE pipe PN6 special with specials ISI Mark collect the water. AR
525
496
260505
... More
Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 15 (DSR-18.34)
10
14704
147044.2
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work ,40 mm dia nominal bore. (DSR-18.9.5)
200
409
81994
... More
Providing and fixing gun metal gate valve with C.I. wheel of approved quality 40mm dia. (DSR-18.17.3)
20
601
12030.2
... More
Providing & fixing Plastic Automatic Hunter I 25 Pop UP sprinkler (MR)
20
5500
110000
... More
Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :150 mm diameter CLASS I (DSR-18.31.3.1)
3
5072
15217.68
... More
Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : (DSR-18.59.3)
2
6475
12950.54
... More
Providing and laying selection first grade grass carpeting at the given area including labour T&P complete. (MR)
13700
235
3219500
... More
Supply & mixing of vermicompost with soil including cost of vermicompost & spreading. (MR)
13700
4
61650
... More
Supply & mixing of manure with soil including cost of manure, transpotation and spreading. (MR)
13700
5
75350
... More
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate. DSR 11.3.1
115.2
447
51519.74
... More
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. DSR 10.1 (AR)
1244.16
220
274163.1
... More
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm. DSR 13.48.1.
921.6
124
114545.66
... More
Milling of distress bituminous layer upto 30mm depth in single pass with suitable milling machine (capable of milling @200-300 sqm area per Hr.) including picking up milled material and stacking old useful material in PWD Store /Site as per direction of Engineer and milled material will be handed over to the department after proper stacking as per direction of Engineer-In-Charge.
2106
100
210600
... More
Scarifying and removing of existing Tennis synthetic turf by appropriate machine including picking up scarified material and dispose off old material with all lead and lift as per direction of Engineer-In-Charge and sports authority.
2106
100
210600
... More
Providing & laying of F.I.H. approved global category Tennis Turf, polyethylene (PE), Water Based), UV resistant, consisting of cast in situ shockpad of 15 mm thickness all approved by FIH standards including laying jointing and fixing the same as per FIH requirement and pasting the synthetic grass as per specification of global category FIH norms including all marking on the surface as per FIH rules and standards etc complete line marking and as per the following minimum FIH specification (given below) and testing by FIH accredited laboratory on the material and on finished work and as per approvals and direction of Engineer-In-Charge. The minimum specifications for Astro Turf are - YARN-Structure- Monofilament micro curl. CARPET-TURF Pile height 13 mm + 1 mm, Gauge3/16 inch, STITCHES / 10 cm 32.5 (± 1), STITCHES / m2 68,040 (±10%), PILE HEIGHT 13 mm (± 10%), TOTAL HEIGHT 15 mm (± 10%), PILE WEIGHT 1,700 gr/m2 (± 10%), TOTAL WEIGHT 3,578 gr/m2 (± 10%) , Pile construction Needle punched. SHOCKPAD- Shockpad type and thickness 15 mm in situ Mass per unit area of shockpad 13.25 kg/m2 Tensile strength of shockpad 0:48MPa.
2106
1350
2843100
... More
Providing and laying tack coat over existing black top surface with bitumen Emulsion medium setting up @3 Kg per 10 Sqm area as per clause No.503 of MORT &H specification of road works (IVth Revision 2001/latest edition) complete in all respect, i/c cost of bitumen VG-10.
2106
83
175029.66
... More
Providing & Laying 30 mm thick compacted Bituminous Concrete (BC) in one layer with 100-120 TPH batch/ drum type hot mix plant and with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per clause No. 507 MoRT&H specification (5th Revision) 2013 for road and bridge works (5th Revision)2013 using minimum 5.4% (upto 40 mm thick) to bitumen grade CRMB-55 as binder content by weight of total mix, complete in all respects including cost of bitumen instruction issued from time to time by MoRT&H regarding machinery & bitumen will be followed strictly. The use of self-propelled mechanical paver fitted with electronic sensor device conforming to MoRT&H specification is mandatory.
100
1200
120000
... More
RESIDENCE, Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.DSR 2.6.1
2148.44
129
277664.39
... More
Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.D.S.R 2.25 (a)
112.81
510
57539.87
... More
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.DSR 2.27
148.66
1546
229883.36
... More
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).(DSR-4.1.8)
455.94
4960
2261476.08
... More
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.DSR 2.35.3.1
1154
225
260527.04
... More
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).DSR 5.3
77.49
8377
649173.25
... More
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).DSR 5.3
157.35
8377
1318201.2
... More
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).DSR 5.3
3.72
8377
31164.34
... More
Brick work with bricks of class designation 15 (Class-150) in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand (FM 1.50 to 2.00)).AR
588.01
6935
4078184.52
... More
Brick work with bricks of class designation 15 (Class-150) in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand (FM 1.50 to 2.00)).AR
333.29
8386
2795049.93
... More
Half brick masonry with bricks of class designation 15 (Class-150) in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement : 4 coarse sand (FM 1.50 to 2.00)).AR
502.68
1011
508682
... More
Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.DSR 4.13
146
106
15537.32
... More
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :DSR-22.7.1
900.05
1226
1104010.33
... More
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:DSR 9.21.1
142.28
1742
247874.52
... More
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete.DSR 10.25.1
6299.87
90
566988.3
... More
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.DSR 10.26.1
2724.98
143
390489.63
... More
Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete.DSR 9.51.2
123.86
683
84702.9
... More
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.DSR-5.22.6
288.88
7852
2268542.86
... More
Fixing of steel or wooden chaukhats in position. Door chaukhats.MR
80
100
8000
... More
Fixing of steel or wooden chaukhats in position. Window chaukhats..MR
60
80
4800
... More
Fixing of steel or wooden chaukhats in position. Ventilator chaukhats..MR
25
40
1000
... More
12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand).DSR-13.4.2
5827.02
250
1458036.94
... More
Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.DSR 13.76
741.35
73
54303.89
... More
Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. (40mm thick).DSR 11.6.1
348.11
351
122186.61
... More
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 600x600mm.DSR 11.41.2
649.33
1131
734463.66
... More
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 600x600mm.DSR 11.46.2
96.02
1181
113475.48
... More
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25mm thick.DSR 11.26.1
66.61
1418
94491.61
... More
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.DSR 11.27.1
9.34
1714
16013.71
... More
Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.DSR 11.37
191.61
798
152987.17
... More
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture.DSR 13.48.3
579.42
124
72016.11
... More
Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture
284.55
128
36516.3
... More
Finishing walls with Acrylic smooth exterior paint of required shade: - New work (Two or more coat applied @ 1.43 Ltr./10 Sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10 Sqm.DSR 13.47.1
3693.35
124
460117.54
... More
Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour :DSR 13.41.1
1587.9
135
214652.32
... More
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.DSR 13.80
4529.76
113
514671.33
... More
Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes.(D.S.R-10.30.1)
123.86
775
96016.27
... More
Providing Stainless steel sliding bolts 16 mm dia with nuts and 250mm long.MR
80
500
40000
... More
Providing Stainless steel tower bolt with 250 mm x 10mm.MR
160
400
64000
... More
Providing Stainless steel tower bolt with 200 mm x 10mm.MR
160
300
48000
... More
Providing Stainless steel door handles with screws 125 mm long. MR
160
200
32000
... More
Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover.DSR 10.6.1
28.35
2660
75411.28
... More
Providing & fixing ball bearing for Rolling shutter.DSR 10.7
5
358
1792.5
... More
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm.DSR 8.2.2.2
14.4
3739
53854.56
... More
Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, buttresses and cantilevers.DSR 5.9.5
687.74
536
368766.19
... More
Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform.DSR 5.9.3
713.1
675
481456.6
... More
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).DSR 5.2.2
29
7976
231323.14
... More
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).DSR 5.1.2
35.08
6648
233222.36
... More
Brick work with bricks of class designation 15 (Class-150) in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand (FM 1.50 to 2.00)).AR
449.62
1011
454988.46
... More
Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete.DSR 5.9.1
152.74
288
44024.25
... More
Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts.DSR 5.9.6
369.11
706
260798.36
... More
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).DSR 5.1.2
2.19
6586
14424.41
... More
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.DSR 10.16.1
990
141
140134.5
... More
P/L in cement concrete 1: 2: 4 (1 Cement : 2 coarse sand : 4 graded stone grit 20mm nominal size and curing complete including cost of form work for fixing of hold fasts including of supply of all materials labour T&P etc.required for proper completion of work. Strength should not be less than M-200. (DSR -4.1.3)
174.5
5736
1001033.21
... More
Providing and laying in position bitumen hot sealing compound for expansion joints etc.Using grade 'A' sealing compound. DSR- 16.46.1
28.34
6
178.54
... More
1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources).DSR 4.1.3
0.9
5717
5145.36
... More
15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand).DSR13.5.1
192.93
296
57259.69
... More
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.DSR 17.1.1
10
4927
49275.5
... More
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required but for European type W.C. pan with white plastic seat and lid.Make- Cera,Hindware. DSR 17.2.1
5
4744
23720.85
... More
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require, White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tappillar tap.DSR 17.7.3
15
1675
25139.7
... More
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required, Kitchen sink with drain board of size 510x1040x200mm.DSR 17.10.1.1
15
5057
75859.65
... More
Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Felxible pipe 40mm dia.DSR 17.28.2.2
15
87
1305.75
... More
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.DSR 17.31
15
1170
17562
... More
Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge.15mm nominal bore.DSR 17.16A
15
254
3813.45
... More
Providing & fixing 600 mm long tower rail with total length of 645mm, widht 78 mm and effective height of 88mm, weighing not less than 190 gms.DSR 17.16A
15
516
7743.15
... More
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore.DSR 18.53.1
80
418
33453.6
... More
Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :100 mm diameter.DSR 18.22.1
15
141
2118.3
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 25 mm nominal outer dia Pipes,DSR 18.7.3
750
292
219285
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 40 mm nominal outer dia Pipes.DSR 18.7.3
425
377
160531
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia Pipes.DSR 18.8.2
425
391
166362
... More
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes.a) 110mm diameter.DSR 12.41.2
150
274
41220
... More
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.a) 110mm . DSR 12.43.2
65
270
17572.75
... More
Providing & fixing CPVC pipes complete with CPVC fittings & clamps including cutting & making good the walls etc.(internal work). Exposed on wall 25mm dia nominal bore (medium duty).DSR 18.7.3
275
292
80404.5
... More
Concealed pipe including painting with anticorrosive bitumatic paint, cutting chases and making good the wall. 15mm dia nominal bore. DSR 18.40.1
300
8
2631
... More
Concealed pipe including painting with anticorrosive bitumatic paint, cutting chases and making good the wall. 20mm dia nominal bore.DSR 18.40.1
475
10
4997
... More
Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions. 15mm nominal bore.DSR 18.21.2.1
30
71
2135.1
... More
Providing & fixing CP brass short body of approved quality conforming to IS 8931 15mm nominal bore.DSR 18.21.2.1
30
369
11070.6
... More
Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15mm nominal bore.DSR 18.51.1
15
581
8726.1
... More
Providing and fixing gun metal gate valve with wheel of approved quality. 25 mm nominal bore.DSR 18 17.1
40
453
18127.6
... More
Providing and fixing gun metal gate valve with wheel of approved quality. 32 mm nominal bore.DSR 18.17.2
15
502
7531.8
... More
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 25 mm nominal bore.DSR 18.18.3
15
337
5068.05
... More
Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.Circular Tank.DSR 18.48
15000
8
120150
... More
Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m. (a) Pipes 80mm to 300mm diameter.DSR-2.10.1.2
300
256
76923
... More
Providing, laying and joining glazed stone ware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. (a) 100mm diameter.DSR-19.1.1
150
323
48450
... More
Providing, laying and joining glazed stone ware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete (b) 150mm diameter.DSR-19.1.2
150
506
75994.5
... More
Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design. (a) 100mm diameter S.W. Pipe.DSR-19.2.1
150
702
105369
... More
Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design. (b) 150mm diameter S.W. Pipe.DSR-19.2.2
150
859
128863.5
... More
Providing and fixing square-mouth S.W. gully trap grade‘A’ complete with C.I. grating, brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design. 150 x 100 mm size P type.DSR-19.4.2.1
60
1990
119451.6
... More
Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). With FPS bricks of class designation 7.5 (i) For Sewer Line. DSR 19.7.1.1
30
9298
278958.9
... More
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Group C.DSR 1.8.3
175
1098
192263.75
... More
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. DSR 1.9
20
1107
22155.4
... More
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Group C. DSR 1.8.3
105
1098
115358.25
... More
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.DSR 1.12
150
253
38091
... More
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C. DSR 1.10.3
5
1115
5576.85
... More
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm. DSR 1.21.1
700
97
68124
... More
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X2.5 sq. mm + 1X2.5 sq. mm earth wire
600
209
125454
... More
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire.DSR 1.14.3
500
253
126970
... More
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire.DSR 1.14.4
300
333
100134
... More
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2X1.5 sq. mm + 1 X 1.5 sq. mm earth wire.DSR 1.14.1
300
177
53145
... More
Installation .Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing up to two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.Cat. A . DSR 1.35
30
90
2714.4
... More
Supply & fixing of fancy type round ceiling fitting made of polycarbonate for and with 1x 15/18 watt CFL complete in all respects.Cat. AA.MR
10
950
9500
... More
Supply & fixing of factory wired Box/ Channel type T-5 energy saver with bright anodized aluminium reflector and end covers suitable for 1 No. 28 watt T-5 lamp with 1X28 watt T-5 lamp etc. complete as required.MR
10
1580
15800
... More
Supply & fixing of factory wired HPF box type, flourescent tube light fitting suitable for 1x20 / 1x18 watt decorative mirror complete including tube etc.on surface complete in all respects.Cat. AA. MR
10
1020
10200
... More
Supplying and fixing call bell/ buzzer suitable for single phase, V, complete as required.DSR 1.38
5
75
376.35
... More
Earthing with G.l. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.DSR 5.2
5
5211
26059.6
... More
Supplying and laying 25 mm X 5 mm G.l. strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.l. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.l. nut bolt & spring washer spaced at 50mm).DSR 5.9
125
109
13685
... More
Supplying and laying 6 SWG G.l. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with Gl thimble etc. as required.DSR5.7
175
38
6786.5
... More
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole. DSR 2.10.1
75
194
14598
... More
Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 A .DSR 2.15.3
20
2183
43672.2
... More
Construction of recess distribution board of all sizes including cutting of brick work providing lintel of suitable size & thickness plastering etc. with supply of all materials, labours, T & P etc. required for proper completion of work.600x480x200 mm. size.MR
20
650
13000
... More
Supply and fixing of factory fabricated M.S. box in existing sunk with Godrej type almirah cover with handle etc. fabricated from 18 SWG M.S. sheet duly painted with red oxide primer followed by two coats of synthetic enamel paint complete with necessary conduit entry and DP/TPN; fixing arrangement and provision for compartment for loose wires, openable housing on the top and hold fast etc. including supply of all material, labour and T & P etc. required for proper completion of the work.600x480x200 mm. size.MR
60
1720
103200
... More
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/lsolator).6 way , Double door.MR
10
1677
16772.4
... More
Supply & fixing of Crimping, solder, less, copper ton electroplated lugs of Dowel/ismail make suitable for 1.5 sqmm to 6sqmm cables, including tapping with insulating tape, etc. complete in all respects.MR
40
15
600
... More
Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.DSR 2.11
10
9
98.8
... More
Supply and fixing of power plug with 15A/250 V flush type switch and 3 Pin 15 A/250V flush type socket in suitable M.S. box of 175mmx100x50mm size Switch bakellite sheet cover 3mm thick fixed with brass machine screws and cup washer.MR
50
340
17000
... More
Supply & fixing of Sheet Steel Enclosure Surface/ Flush Mounting fitted With 20/32 Amp. 2Pin and earth metal clad scraping earth plug and socket complete in all respects as per direction and satisfaction of engineer-in-charge.MR
20
1620
32400
... More
Erection and testing exhaust fan on the exhisting hole with suitable size of rag bolts nuts and washers etc. complete in all respects.MR
15
195
2925
... More
Supply & fixing of 16 gauge M.S.drum duly painted including making hole in the wall for exhaust fan and finishing properly etc. complete as required.MR
15
810
12150
... More
S/F of hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16 SWGM.S. sheet incorporating 10mm dia, M.S. round barduly bent for supporting fan hanger dully painted withred oxide and screwing arrangement with wiring conduit laid in the R.C.C. roof before concreting along with supply of all materials, labour T & P etc., for proper completion of work.MR
60
150
9000
... More
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Up to 35 sq. mm . DSR 7.1.1
550
294
161832
... More
Supply & fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respects. The armouring of the cable shall be properly connected with the earth as per direction of ingineer in charge.10 sqmm 4 core.MR
30
87
2610
... More
Supplying and fixing of Palm / pin type copper tin plated cables sockets (lugs) to the cable leads, insuslating with tape and making of connections etc. complete in all respects as per direction of Engineer-Incharge.10 Sq.mm. MR
75
20
1500
... More
Supply and fixing of LED street light fitting having diecast aluminium body and diffuser with driver set suitable for 150 watt. confirming to IP 65 and above protection complete in all respect.CAT-AAA. MR
65
12300
799500
... More
Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair.DSR 1.18.2
750
28
21667.5
... More
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. DSR 1.19
600
35
21438
... More
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet. DSR 1.24.6
10
112
1125.3
... More
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet.DSR 1.24.7
10
112
1125.3
... More
Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 75mm X 75 mm X 60mm Deep . DSR 1.22.1
10
135
1353.4
... More
Supplying and fixing following size/ modules, Gl box along with modular base & cover plate for modular switches in recess etc. as required.1 or 2 Module (75mm X 75 mm) .DSR 1.27.1
20
226
4531.4
... More
Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.DSR 1.51
60
157
9442.8
... More
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.DSR 1.26
25
30
760.25
... More
Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.CSR 19.1
60
2043
122622.6
... More
Supply of AC 230/250 Volts, 50 Hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required-Make: USHA Cat No. TURBO JET DLX.300mm sweep. MR
15
1380
20700
... More
Main LT Panel, Supply & Errection of factory fabricated & wired metal clad and dustand vermin proof floor mounting entreis Electrical control panel with TPN MCCB s(four pole 36 KA with thermal magnatic release) Switches complete and lnstrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters (KVA, P.F. K.W etc) in each phase with touch type selector switches for different readings, instrument fuses, current transformer etc. The panel board shall have suitable capacity electrolytic aluminium busbars as per IS8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCB's shall be complete with suitable cable end boxes, compression glands and indicating lamp on incoming etc.
The Job includes the grounting of the board as per directions of E/Ich. All out goings of 100 Amp and above shall have an Ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2 mm. Cubicle type switch board shall be of cat A & B only. (S.I.No.813 e),Incoming, 400 Amp 50KA MCCB. 1No.Out going,100 Amp 25 KA MCCB. 3 Nos.63 Amp 18 KA MCCB. 3Nos.100 Amp 25 KA MCCB. 1 Nos. Spare,63 Amp 18 KA MCCB. 1 Nos. Spare.MR
5
214532
1072660
... More
Supply & fixing of ISI marked portable fire extinguishers, complete with internal charge and wall bracket along with supply of all materials and labour for proper completion of work. ISI Marked IS : 2878 & TAC Approved,CO2 type. 4.5 Lt.capacity.MR
10
11980
119800
... More
Supply & fixing of ISI marked portable fire extinguishers, complete with internal charge and wall bracket along with supply of all materials and labour for proper completion of work.ISI Marked IS : 15683 & TAC Approved, ABC type. 6.00 kg. Capacity.MR
10
9100
91000
... More
S/F of Fire Bucket, round bottom made of G. I. sheet 9-11 Ltr. capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of Engineer-in-Charge.MR
25
490
12250
... More
110MM PVC casing pipe of ISI mark.
300
400
120000
... More
110MM PVC slotted pipe of ISI mark.
100
550
55000
... More
P/ F 50mm GI pipe (B) class.
225
300
67500
... More
Nylon mesh for filter.
5
500
2500
... More
Plastic dori.
5
300
1500
... More
Solvent cement.
5
350
1750
... More
110mm End cap.
5
300
1500
... More
110mm Submersible cap.
5
300
1500
... More
50mm MS clamp (Heavy).
5
1000
5000
... More
50mmGI elbow.
5
200
1000
... More
50mm X 110mm GI nipple.
5
250
1250
... More
2 HP 9 Stage submersible pump of ISI mark with automatic panel.
5
30000
150000
... More
2.5 sqm. Submersible cable.
350
300
105000
... More
Drilling charges for 6" dia tubewell.
400
700
280000
... More
Pea Gravel.
6.25
2500
15625
... More
2" MS socket.
20
300
6000
... More
Cartage of material upto site.
5
2000
10000
... More
Fixing testing and commissioning of Pumpset with lowering & Electric wiring with starter etc. complete as required.
5
5000
25000
... More
Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design:(With 20x20mm square bar).DSR 19.15.1
90
396
35694.9
... More
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.DSR 19.32.1
10
19558
195589.8
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%