Unnao Shuklaganj Development Authority Tender

First Class B/W in 1:4 cement and C/sand mortar in foundation and plinth including supply of all mat, lab and tools and plants etc. reqd for proper completion of the work.PWD SOR S I No.305(b)/2017-18

12 mm thick plaster 1:3 cement and coarse sand mortar etc all complete. PWD SOR S I No.583/2017-18

Finishing walls with water proofing cement paint of required shade : on New work (Two or more coats applied @ 3.84 kg/10 sqm) (PWD SOR S.No 660/2017-18)

Providing and laying in cement concrete 4:2:1 of not less than strength of M150 stone ballast (20 mm. nominal size) :2 approved coarse sand:1 cement and curing complete, including cost of formwork in foundation and floors PWD SOR S.I.No.279(b)/2017-18

Part B Supply and instalation of Genrator- Supply of 40 KVA Three phase silent DG Set comprising of Cummins/kirloskar/Eicher make engine developing of 40 KVA 3 Phase stamford make alternator mounted on a common base, complete, with fuel tank, battery and leads, Manual Control Panel, Residentional Silencer, First fill of oil, AVM Pads, Acoustic Enclosure and 5C warranty for 5 year Genrator of lowest price. (quatation Rate)

Supply & Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN MCCB's (Four Pole 36 KA withthermal magnatic release) Switches Complete and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters (KVA,P.F, KW etc) in each phase with touch type selector switches for different readings, instrument fuses current transformer etc. The panel board shall have suotable capacity electrolytic alumininum busbars as per IS 8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/BMC support wuth deteachable side covers and shall be suitable for extention on the sides. The MCCB's shall be complete with suitable cable end boxes, compression glands and indicating Lamp on incoming etc. The Job includes the grounting of the board as per directions of Engineer-in-charge. All out goings of 100 Amp and above shall have an Ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2 mm. Cubicle type switch board shall be of cat B only. incoming 100 Amp MCCB-1 N0 and outgoning 63 Amp. MCCB-1 N0 & 32 Amp. MCCb-2 Nos.. ( PWD SOR -S.I. No. 811( C ) (ii) 2018

S/L of 70 sqmm.3-1/2 core aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respectes. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. ( PWD SOR -S.I. No. 501( m) 2018

S/L of 25 sqmm.3-1/2 core aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respectes. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. ( PWD SOR -S.I. No. 501( j) 2018

Supplying & fixing of brass nickle plated 70 sqmm3-1/2 core compression gland for PVC isulated & armoured served sheathed, underground cable including rubber ring etc. comolete in all respects. The armouring of the cable shell be properly connected with the earth as per direction of Engineer-Incharge . ( PWD SOR -S.I. No. 503(m) 2018

Supplying and fixing of plam or pin type copper tin plated cable socket (lug) 70 sqmm to the cable leads, insulating with tape and making connection etc. complete in all respects as per direction of the Engineer-Incharge.( PWD SOR -S.I. No. 504(h) 2018

Supplying & fixing of brass nickle plated 25 sqmm3-1/2 core compression gland for PVC isulated & armoured served sheathed, underground cable including rubber ring etc. comolete in all respects. The armouring of the cable shell be properly connected with the earth as per direction of Engineer-Incharge ( PWD SOR -S.I. No. 503( j) 2018

Supplying and fixing of plam or pin type copper tin plated cable socket (lug) 25 sqmm to the cable leads, insulating with tape and making connection etc. complete in all respects as per direction of the Engineer-Incharge. ( PWD SOR -S.I. No. 504(e) 2018

S/burring of safe earthing electrode T-19 (Hot Dip Galvanised), length upto 3000 mm, out dia 50 mm, inner dia 25 mm, terminal dia 12 mm outer GI pipe of 16 SWG & inner GI Pipe 12 SWG with hot dip Galavnisation upto 100 micron filled with crystalline conductive misxture (CCM) having anti corrosive & condutive property with 50 kgs activated soil (BFC) capable of reducing the soil of resitivity with good mixture of retaining capicity & one earthing lead of 25 mm X 3 mm GI strips upto switch board (from apron to switch board, cost of GI strip will be extra) along with 30 centimeter squre C.I Frame Hinged covered and machinery houjing make as approved in U.P.PWD & C.P.R.I certified as directed by E/I all complete. ( PWD SOR -S.I. No. 725(b) 2018

S/L of HDPE (DWC) Pipe ISI marked with all accessories like socket, bend, couplers etc. conforming to IS 149930, Part-II Complete with fitting and cutting, jointing etc. direct in ground (75 Cm Below ground level) including excavation and refilling the trench but exluding sand refilling the trench but excluding sand cushing and protective covering etc. complete as required. 90mm dia(OD-90 mm & ID 76 mm Nominal) (OD/ID) PSR