Rajya Krishi Utpadan Mandi Parishad Tender

501(r) 240 sq. mm 3.5 core

Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-Incharge. 503(C) 16 sq. mm 2 core

503 (r ) 240sqmm 3-1/2 core

503 (k) 35sqmm 3.5 core

Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-Incharge. 504 (C) 16 sqmm

504 (m) 240sqmm

504 (f) 35sqmm

Supply & erection of “D” clamps of 50mm x 6mm flat iron on steel tubular poles/steel rail poles with bolts, nuts etc. complete in all respects including painting with aluminium paint. 623

Supply & fixing of 100mm x 100mm shackle insulator/100mm x 80mm pin insulator including G.I. Bolts/spindle nuts etc. complete in all respects. 621

Supply & fixing of 230mm x 32mm x 1.5mm galvanized steel strips including holes for shackle insulators pins and bolts etc. complete in all respects. 622

Supply & erection of stay set at 3.5 Metres away from the pole complete with galvanised 19mm dia x 1.80 Metre long stay rod, 30 cm x 30 x 6.3mm anchor plate, thimble stay clamps, stay insulator, 19mm 600mm double screw tightener, 7/13.5mm G.I stay wire etc. in 1:3:6 cement concrete complete in all respects. 631

Supply & erection of hexagonal/cradle type gaused of G.I wire no. 8 to 4 SWG including binding etc. complete in all respects. 629

Painting of the electric pole with 2 coats of aluminium paint over red oxide primer complete in all respects. 634

Supply & erection of overhead line with ACSR conductor on poles / service bracket including binding etc. complete in all respects.

To tighting of ACSR condoctor LR

Supply & erection of overhead line with G.I. wire no. 8 to 4 SWG on poles/serivce bracket including binding etc. complete in all respect.

Supply and fixing of one number 8 SWG G.I. wire in 15mm dia. G.I. pipe for earthing, laid in ground or in wall duly concealed including the cost of cement, sand, labour, T&P other material required for proper completion of the work as directed at site. 721

Supply and burying of 600mm x 600mm x 6.0mm G.I. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthing lead of one no. 8 to 10 SWG GI wire in 15mm dia G.I. pipe up to switch board (from apron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge completein all respects as per drawing (This will apply for earthing of poles also). 702

Dismentling/shifting /making foundation of damage pole.LR Only

S/F of 100mm. dia G.I. pipe 14:13:3 DSR

S/F of 50mm. dia G.I. pipe 14:13:1 DSR

S&F of 100 A. 415 V Metal clad TPN CFS complete with HRC fuse etc. on angle iron frame complete in all respect. 353

S/f of spacer APPD

Supply and fixing of 200 Amp. Four pole hange over switch on 50 mm ×50 mm × 6 mm angle iron frame, including the cost of labour, T & P painting and other material required for proper completion of the work as per direction and satisfaction of E /I 379

Supply and Erracetion of factory fabricated and wired metal clad dust and vermin proof floor mounting M.S. channel Base with bottom and top cable entreis Electrical control panel with TNP MCCB’ s [ Four Pole 36 KA with thermal magnetic release] Switches Complete and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage current and other parameters [ KVA; P.F; KW etc] in each phase with touch type selector switches for different readings instrument fuses current transformer etc. The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC\BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCB’s shall be complete with suitable cable end boxes; compression glands and indicating lamp on incomingetc. The job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above shall have an Ammeter. The panle board shall be fabricated with CRCA sheet with a minimum thickness of 1.6mm\2mm. Cubicle type switch board shall be of cat A and B Only. Incoming. 630Amp. MCCB –1No. Out going. 100 Amp.MCCB -5N0. and 63 Amp MCCB-2 No. Cat. B. Pannel Cubical Type.

Debuct in item no. 501 (a) 501 (t) and 506 (a) to (f) when cables is passed through G.I./M.S. or Hume pipe in road crossing or along the wall. The cost of the G.I. pipe, hume pipe is to be extra when and where required. 507