Public Works Department Tender

Wall painting (two coat) with plastic emulsion paint of approved brand and manufacture on decorative wall surface to give an even shade including thoroughly brushing the surface clean all of dirt, grease loose pieces and prepare smooth. (Chap-15, SI. 27&28)

Providing and laying vitrified tiles in floor without lean concrete of 600x600mm sizes (thickness 10mm), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in desired colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS:15477, including grouting of joints. (Chap-14, SI. No. 23a)

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of Ist quality conforming to IS:15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. complete (Chap-14, SI. No. 14)

Providing and fixing white vetreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures completed, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid (Chap-24, SI. No. 2)

Providing and fixing wash basing with C.I. brackets, 15mm, C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. (Chap.-24 SI. No. 3a)

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (Chap-24, SI. No. 7)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps i/c cutting and making good the walls etc. (Chap-23, SI. No. 20) but 15mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps i/c cutting and making good the walls etc. (Chap-23, SI. No. 20) but 20mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps i/c cutting and making good the walls etc. (Chap-23, SI. No. 20) but 25mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps i/c cutting and making good the walls etc. (Chap-23, SI. No. 20) but 32mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work) (Chap-23 S.I. No. 24) but 15mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work) (Chap-23 S.I. No. 24) but 20mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work) (Chap-23 S.I. No. 24) but 25mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work) (Chap-23 S.I. No. 24) but 32mm dia nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms (Chap-23 S.I. No. 34)

Providing and fixing C.P. brass stop cock (concealed) of standard desing and of approved make conforming to IS:8931 (Chap-23 S.I. No. 35)

Providing and fixing C.P. brass angle value for basing mixer and geyser points of approved make conforming to IS:8931 (Chap-23 S.I. No. 36)

Providing and fixing brass stop cock of approved quality (Chap-23 S.I. No. 39) but 15mm dia nominal bore.

Providing and fixing brass stop cock of approved quality (Chap-23 S.I. No. 39) but 20mm dia nominal bore.

Providing and fixing C.P brass shower rose with 15 or 20mm inlet (Chap-23 S.I. No. 37) but 50mm dia meter

Dismantling cement concrete or brick or granolithic floors including stacking of dismantled mterials as directed by E/IC within a distance of 60 meter (200feet) stone flagged or tiled (Chap-17 Item No. 698)

Dismantling existing plaster including disposal of refuse as directed by E/IC within a distance of 60 (SI. No. 706)

12mm cement plaster with cement mortar in proportion of 1:4 cement and coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth. (Chap-13, SI. No. 2)

Applying priming coat over new steel and other metal surface upto 10cm. In width or girth or small not exceeding 0.10 sqm area after and including preparing the surface by thorughly clearing oil. Grease, dirt and other foreign matter and scoured with wire brushed, fine steel/wood, scrapper, sand papering and knotting including cost of all materials, labour, T&P etc. required for proper completion of work. (Chap-15, SI -1)

Conditions:- SCHEDULE - “C” 1-   Bitumen V.G.-10 shall be issued from the central store CD-3, PWD, Mainpuri at Stock issue rate at the time of issuing the material from the store and the bitumen will be recovered from the contractor's bill at the stock issue rate or market rate whichever is maximum. 2- Emulsion if available shall be issued from the central store CD-3, PWD, Mainpuri at Stock issue rate at the time of issuing the material from the store. 3-     There shall be no claim of contractor, if the material is not issued by the department due to non-availability in store or any other reason. 4-     The unconsumed material issued in excess of bonafide consumption norms, shall have to be returned back to the store as mentioned above, failing which a recovery at the Penaltative rate, i.e., double the issue rate shall be made from the contractor’s bill. 5-     Contractor have to return empty bitumen drums / emulsion drums immediately, failing which a recovery at the punitive rate i.e., Rs. 3000 per drum shall be recovered from the contractor’s bill. 6-     The departmental road roller if spare, shall be made available to the contractor at site @ Rs. 2450 per day including POL charges, wages of driver and cleaner. If roller is kept idle due to non-availability of material or labour, recovery @ Rs. 2450 per day shall be made from contractor’s bill for idle period. 7- All material should be purchased from approved quarry