Military Engineer Services Tender

M&L10 mm thick plaster in cement mortar (1:4) on ceiling finished even and smooth without using extra cement complete all as specified and directed .

M&L for cement concrete as 1:4:8 (40 mm graded stone aggregate) in foundation, filling and mass concrete complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over cut to length bent to shape as required including cranking bending spirally for hooking ends and binding with mild steel wires (annealed not less 0.9 mm dia) complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) with fair and smooth finished surfaces complete all as specified and directed.

M&L for RCC Type A-1, nominal mix (using 20 mm graded aggregate) in slab supported in walls complete all as specified and directed.

S & F for 2000 ltr rotational moulded polyethylene water storage tank triple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed.

S&F for 15mm bore tubes medium grade galvanized with all fitting and fixed complete to walls and ceilings or laid in floors of any length, complete all as specified and as directed

S&F for 20mm bore tubes medium grade galvanized with all fitting and fixed complete to walls and ceilings or laid in floors of any length , complete all as specified and directed

M&L Cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 10cm but n exc 20cm girth making good to facings where required and in cement mortar 1:3 complete all as specified and as directed.

S&F for Gun-metal, globe or gate valves of 15mm dia, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F for Gun-metal, globe or gate valves of 20mm dia, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Supply & fixing ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size complete all as specified.

M&L Glazed ceramic coloured tiles on vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set in walls and laid over and including 10 mm thick screed bed in CM 1:4 and jointed in neat cement slurry and pointed in white or colour cement to match including dismantling of old tiles and removing the same from site, complete all as specified and directed.

M&L for non skid ceramic coloured joint free tiles 7 to 8 mm thick square or rectangular of size exc 0.11 but not exc 0.18 sqm in floors laid over and including 15 mm thick screed bed in CM 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles including dismantling of old tiles and removing the same from site, complete all as specified and directed.

M&L for plain cement concrete (1;2:4) type B-1 in coping /benching and similar work rounded or chamfered on edges using 20 mm graded stone aggregate including necessary form work complete all as specified and directed.

M&L PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in surfaces channel and drains complete all as specified and as directed.

Extra for forming fair finished drain or channel up to 30 cm inner girth in cement concrete, using extra cement including forms, moulds,/stopped ends etc complete all as specified and as directed.

M & L for 75 mm thick cement concrete type C-2, 1:3:6 mix, (using 40 mm graded stone aggregate) as in sub base for floor , complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) in plinth protection, surfaces finished even and fair complete all as specified and as directed.

M & L for hardcore of broken stone or boulders gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface, for floor and for paver block, complete all as specified and as directed

M&L preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L preparation of new surfaces and applying three coats of white wash on ceiling all as specified and directed.

Demolition RCC (reinforcement cut as required to facilitate demolition Concrete of any description and in any position complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 including necessary welding, drilling hole complete all as specified and as directed.

Dismantling Plain or corrugated steel sheets in roof coverings complete all as specified and directed.

S & F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour, AZ150 having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Excavation in trenches not exceeding 1.5 wide and not exceeding 1.5 m in depth for laying of cables, pipes and getting out incl trimming the sides and forming bottom surfaces to required levels in soft/loose soil complete all as specified and directed.

Returning, fitting in including spreading, levelling, watering & well ramming in layers not exceeding 25 cm thick complete all as specified and as directed.

Removing excavated material (soils) to a distance not exceeding 50 M and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply and spreading ganga sand dry, clean in trenches as cushioning to underground electric cable provided with a layer of 80mm deep before laying and 150mm over cable laid in trenches complete all as specified and directed. (Note: Punned thickness shall be considered for measurement purpose.)

M & L for well burnt brick sub class B old size laying in trenches for cable protection complete all as specified and directed.

Supply and laying in trenches GI pipe light grade with fitting of size 100 mm bore for protection of cable complete all as specified and directed.

M & L for cutting of PCC/Hard standing/WBM road not exceeding 45 cm in width not exceeding 60 cm in depth for passing of cable and making good of disturbed surface to match with the existing surfaces by using old and new material i.e bitumen/PCC (1:2:4) type B-1 complete all as specified and directed .

Supply, laying in ducts/trenches/fixing on wall/pole and testing of LT cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable heavy duty 1100 Volts grade with stranded aluminium conductor of size 95 Sqmm 3.5 Core suitable for earthed system complete all as specified and directed.

Supply, laying in ducts/trenches/fixing on wall/pole and testing of LT cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable heavy duty 1100 Volts grade with stranded aluminium conductor of size 50 Sqmm 3.5 Core suitable for earthed system complete all as specified and directed.

M & L for earthing complete with GI earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly to ground vertically to a depth not less than 2.25 Mtr below the ground level with top edge of earth plate not less than 1.5 Mtr below normal ground level connected to GI strip 32mm x 6 mm as earthing lead protected with 50mm dia light grade GI pipe, filling around with charcoal dust and salt including excavation, returning filling of earth work and disposal of surplus soil to a distance not exceeding 50 mtr and connected to GI strip by means of GI nuts, bolts and washers strip connected to earth plate including chamber PCC 1 : 3 : 6 type C-1 using 20mm graded stone aggregate and pre cast RCC cover 40 mm thick reinforced with 6 mm dia round at the rate of 75 mm C/C both way with 12 mm dia mild steel plain bar lifting handle 2 Nos funnel with wire mesh, 20 mm dia GI pipe light grade watering pipe and framework complete all as specified and as directed. (Note:- GI pipe and GI strip upto 7.5m is included in the unit rate quoted by the contractor.)

Supply, installation, commissioning and testing of outdoor type LT panel (CPRI Approved) made out of 3.15 mm thick CRCA sheet metal, double door and suitable MS angle iron base frame, cubical type floor mounted 3 Phase, 4 Wire, 415 Volts properly insulated aluminium bus bar - 04 Nos having capacity 300 amps on phase & neutral, dust and vermin proof, both side open with locking arrangement, danger board plate, duly painted internally and externally with powder coated, fixing in position by provision of platform suitable size built with brick work in CM (1:4), 15 mm thick plastering in CM (1:6) including glands, lugs, thimbles for all cables complete all as specified and directed. Incoming: (i) MCCB 200 Amp, 36kA, 415V, 4P - 01 No Outgoing: (i) MCCB 160 Amp, 36kA, 415V, 4P - 01 No (ii) MCCB 63 Amp, 25kA, 415V, 4P - 02 No

M&L for construction valve pit chamber of size 900x900x900mm internal dimension , 6mm thick MS sheet with 2 Nos MS hinge of suitable size welded with angle iron frame of 40x40x6mm thick with lifting hooks and locking arrangement complete with necessary earth work, brick work in CM (1:6)/ 230 mm thick, PCC bed (1:4:8) type D-2, 150mm thick, 15mm thick cement plaster in CM 1:4 internal surface complete and external surface of wall up to 300 mm front top and applying a coat of black bituminous paint to the steel surface complete all as specified and directed.

M&L for GI Pipe medium grade of 50 mm dia with all necessary fittings such as bend, elbow, socket, TEE, Union, Reducer socket etc and laid in trench/duct/wall/open air etc. including making connection to existing pipe / PVC Tank complete all as specified and directed.

M&L for GI Pipe medium grade of 40 mm dia with all necessary fittings such as bend, elbow, socket, TEE, Union, Reducer socket etc and laid in trench/duct/wall/open air etc. including making connection to equipment / PVC Tank complete all as specified and directed.

M&L for GI Pipe medium grade of 20 mm dia with all necessary fittings such as bend, elbow, socket, TEE, Union, Reducer socket etc and laid in trench/duct/wall/open air etc. including making connection to equipment / PVC Tank complete all as specified and directed.

Supply and fixing gun metal gate valves, high pressure with iron wheel head complete, screwed both ends for iron pipe of size 50 mm bore dia complete all as specified and directed.

Supply and fixing gunmetal gate valves, high pressure with iron wheel head complete, screwed both ends for iron pipe of size 40 mm bore dia complete all as specified and directed.

M&L for sub main wiring with four runs of single core 10 Sqmm (nominal area) PVC insulated and unsheathed multi stranded copper conductor cable LT 1100 grade FRLSH cable concealed wiring drawn in and including non metallic PVC conduit medium grade complete with all necessary fittings and accessories and run of PVC insulated and unsheathed two runs of single core cable with copper conductor of size 6 Sqmm as earth wire (green in colour ) run through PVC conduit and connected to common earth dolly all as specified. Note. Four run of cable and two run of earth continuity wire with one run of PVC conduit of suitable dia shall be measured as one run complete all as specified & directed.

S&F sheet metal enclosures for Vertical distribution board TPN, 4 way double door type including with MCCB 4 Pole, 160 Amps, 36 KA fixed type as incomer with 250 amp rated bus bar complete all as specified & directed.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) TPN of 100 Amps current carrying capacity with fixing in DB complete with connection testing and commissioning complete all as specified & directed.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) TPN of 63 Amps current carrying capacity with fixing in DB complete with connection testing and commissioning complete all as specified & directed.

M& L for earthing complete with galvanized iron earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground (earth pit not less than 2.25 Mtrs deep below ground level) with top edge of the plate not less than 1.50 Mtr below normal ground level connected to galvanized earth lead 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.5 connected to earthing test point all as specified or indicated including testing on completion including PCC pit in (1:3:6) type C-2 cement concrete .RCC 1:2:4 Mix type B reinforced with 6mm dia MS bars @ 150mm RCC cover slab 40mm thick with two no’s fitting handle, GI pipe 20mm dia light grade with funnel & wire mesh for watering and 40mm dia light grade GI pipe for earth strip 4 mm protection etc. complete all as specified and directed by Engr-in-Charge. (Note: Earthing strip and protection pipe upto 7.5 metre length shall be deemed to be included in the quoted unit rate).

S & F Metal clad triple pole and a neutral enclosure with a three pin and earth plug and socket with one MCB TPN 63 Amp 415V complete all as specified and directed.

S & F Metal clad triple pole and a neutral enclosure with a three pin and earth plug and socket with one isolator TPN 100 Amp 415V complete all as specified and directed.

Supply, laying and testing of XLPE insulated , screened, PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty with aluminium conductor 1100 volts grade cross sectional 16 sq mm 4 core, laid in trenches/ducts /encased in GI pipe /fixed to pole complete all as specified and directed.

Supply, installation, testing and commissioning of Washer Extractor complete 40 KG or nearest higher capacity with fully programmable PLC control, front loading and unloading, High speed extraction, Fully suspended soft mount type, Stainless steel construction, High torque drive and heavy duty motors with high efficiency and low power consumption with having electrical water heating system, Manual and auto door mechanism complete, emergency stop switch all as specified and directed by OEM.

Supply, installation, testing and commissioning of Tumble Dryer complete of 40 KG or nearest higher capacity with fully programmable Microprocessor control system, front loading oper pockets, Stainless steel drum, Glass door, Radiator/Heat exchanger design and efficient blower system, Fire suppression system (optional), Self cleaning lint mesh complete all as specified and directed by OEM.

Supply, installation,testing and commissioning of Air Compressor capacity 2 HP horizontal type 415 V, 3 Ph, 50 Hz with suitable air compressor tank capacity for providing service air of pressure range 7-10 bar complete all as specified and directed by OEM.

Supply, installating, commisioning and testing of commericial kitchen mechanical chimney comprising of the following items: (i) Exhaust hood regular type mounted centrally/on wall, rectangular shape 7 foot long and 3 foot wide made out of 0.8 mm thick SS (316 grade) sheet with SS Grease Filters (SS 316) with suitable size SS grills. (ii) SS ducting (24 SWG) (SS 316) 15 foot long with mild steel brackets for fixing / mounting on ceiling / wall, suitable flanges & connections, Tee, Elbows etc. to extract the fumes. (iii) SS ducting (24 SWG) (SS 316) 15 foot long with mild steel brackets for fixing / mounting on ceiling / wall, suitable flanges & connections, Tee, Elbows etc. for recirculating cool air. (iv) Centrifugal exhaust Blower driven by 3 HP, 1440 RPM, 415 V, 50 Hz, 3 phase electric induction motor with suitable damper for achieving 3000 CFM as per site condition with heavy guage SS casing having robust construction, flanges at both end, die cast aluminium impeller having aerofoil design with adjustable pitch angle with and including all connected accessories and fitting fixtures for making full functional including civil work complete all as per specified and as directed. Note: (a) All civil works such as making opening in brick / stone walls including to make good to match with the surroundings, mounting plinth for blower motor assembly etc., shall be carried out by the contractor and the cost of the same shall be deemed to be included in the rate quoted. (b) All mild steel brackets, supports, clamps , flanges etc., as required shall be carried out by the contractor and the cost of the same shall be deemed to be included in the rate quoted. (c) Wiring and control switches as required shall be measured separately under appropriate items of BOQ. (d) Test certificate for motor, blowers, etc., shall be submitted duly tested from NABL accredited lab.

Supply and fix at duct inlet desert cooler electric driven (single phase), having nominal air flow capacity of 4000 CuM per hour or nearest higher size with Steel body and suitable size stand for mounting complete all as specified and directed.