Military Engineer Services Tender

All as per srl item No 2 above but for 5 pin 5 amps socket outlet independent board complete all as specified and directed.

All as per srl item No 2 above but for 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed.

All as per srl item No 2 above but for one light point controlled by two Nos 2 way switches complete all as specified and directed.

All as per Item No 02 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50 Sqmm and green colour earth cable of size 2.50 Sqmm.

M&L for point wiring complete with PVC (FRLSH) insulated unsheathed multistranded copper conductor of size 4 sqmm nominal cross sectional area single core drawn in and including not less than 20 mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, complete including 4 sqmm nominal cross sectional area PVC(FRLSH) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including cutting chases for concealed piping and making good disturbed surface to match the existing surface complete all as specified and directed.

S&F switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed.

S&F switch piano 2- way, 5/6 amps flush type 230 volts complete all as specified and directed.

S&F bell push flush type 5 amps SP 240 volts complete all as specified and directed.

S&F switch in replacement piano flush type one way 16 amps SP 240 volts complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5/6 amps flush type 240 volts complete all as specified and directed.

S&F socket outlet 2 in 1, 6 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S&F bell ding dong AC , 230 VOLTS, single pole complete all as specified and directed.

S&F ceiling rose 65 x 50mm three terminals complete all as specified and directed.

S&F ceiling fan regulator, electronic stepped type 5 stage speed regulation, ISI marked complete all as specified and directed.

S & F lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

S & F sheet metal single pole and neutral enclosure with socket, plug top complete with one single pole MCB of 20 Amps, 240 volts complete all as spd and directed.

S&F in replacement existing U/S light fitting with energy saving decorative LED batten 20 watt (4 Feet), 230 voltas, energy efficient tube light fitting extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffusre & integrated electronic driver complete with all accessories prewired and includeing making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed. Note:- Power factor should not be less thtn 0.95 Make- HALONIX Cat paart No - HLTLD-04-20-CW , ORIENT Cat part No-LBLN-20-C-AL /Phlips Cat part No- BN021C LED22S PSU CW GR

S&F in replacement of old U/S tube light fitting with energy saving decorative batten type 10 watt energy efficient tube light fitting (2 Feet) highly durable surface mounted LED batten constructed of fire retardent engineering grade extruded plastic and decorative end caps with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed. Make- ORIENT Cat part No-LBLN-10-C-SQ/Phlips cat part- BN021LED12S6500PSUGR, HALONIX Cat part no HLTLD-04-10-CW

S&F in replacement of old U/S decorative wall mounting light fittings with opal glass diffuser and stainless steel body suitable for LED lamp 12 Watt (B-22 base) including one number 12 Watt LED lamp complete all specified and directed. Make: HALONIX Cat part No HLWB-01-B22,/Havells - LHFOAJE1TN1I060 /PHLIPS

S&F in replacement enery saving new generation LED 10 Watts, 6000k, IP-65 bulk head luminarie with opal diffuser complete including making connection with 3 core copper flexible cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed. Make :- ORIENT /Phlips / Havells

S&F for replacement of existing unsv security light fittings with LED security light fitting 30/36 Watts, excellent thermally managed pressure die cast alumnium come with in-built photo sensor for automatic on/off, IP-66 including GI bracket made out of GI pipe 40 mm bore medium grade bent to an angle of 135 degree and reduced at the end to 32 mm dia, 1.20 mtr long including 2 Nos clamps, suitable size of nut, bolts complete all as specified and directed. Make: Halonix cat part LED SL 30WHLSLD-ML04-30-CWL-INV-RTC-R/ Orient Cat No: LSFT-36-C-PCK-DLS/ SHAKTI CAT REF

S&F in replacement exisitng unsv Lamp with LED Lamp 9 watt, 6500 K, 230 volts B-22 Base complete all as specified and directed. Make: Havells/ Philips/ Bajaj

S&F in replacement 20 W LED tube with in built driver complete all as specified and directed. Make :- Havells Cat part No-LHLDDCXCML8Q020, Orient Cat part No. LTXL-20-C / Halonix - HLTLD-04-20-CW-PC

S&F 20 watt LED building security light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embeded toughened glass having top opening seperate driver compartment with min IP65 protection connecting the same to making connection with 3 core copper flexible cable of size 23/.0076 from ceilling rose complete all as specified and as directed. Make:- Orient Cat No :LSFS-020-C/ Bajaj Cat No-ENXT P 20L WH PO PC SD/ Halonix Cat No- HLSLD-09H20CWL R

S&F Wall / surface mounted type LED light fitting batten type complete with LED lamp 05- watt, poly carbonate body and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with twine core twisted flexible copper conductor cable complete all as specified and as directed. Make- HALONIX / ORIENT/HAVELLS

Supply & Fix in replacement recess mounted LED luminaire 36W 2'x2', 6500K, fully diffused, CCT, luminous efficacy of not less than 120lm/watt designed for metric false ceiling type or alongwith frame suitable for Armstrong/ US Gypsum or similar mounting system with concealed or exposed 'T' sections, Glare free light alongwith electronic driver complete with all accessories prewired and connecting up with three core twister flexible copper conductor cable with suitable size complete removing unserviceable fittings all specified and directed. Make: Philips Cart Part No. RC380B LED36S-6500G5L60W60 PSU OD SG/ORIENT Cat Ref - LTRAQ-36-C-VO-AL/ BAJAJ Cat ref - BZRSQL 43L LED GX PRO WH. NOTE ;- Cost of necessary T&P included for fixing of fittings in SHIV DEV HALL & Offrs Mess, hight approx 8 Mtr from ground level.

S&F in replacement of exiting unsv light with recess mounting square 12 Watts LED downlight, aesthetically designed PC housing with constant driver including making all electric connections complete all as specified and directed. Make:-ORIENT- Cat Ref - LDRES-12-C-VI /BAJAJ Cat Ref - BGSLO Sleek Recess SQ 12W WH LED/ Phlips Cat Ref - DN097B-LED10S--6500 PSU WH.

S&F in replacement of exiting unsv light with recess mounting round 12 Watts LED downlight, aesthetically designed PC housing with constant driver including making all electric connections complete all as specified and directed. Make:-ORIENT- Cat Ref - LDRER-12-C-VI /BAJAJ Cat Ref - BGSLO Sleek Recess RD 12W WH LED/ Phlips Cat Ref - DN296B LED12S-6500 PSU WH.

S&F in replacement sheet metal enclosure MCB distribution board, double door with IP-43 protection single pole and neutral 240 volts, 8 way, including suitable size copper bus bar and neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed.

S&F in replacement sheet metal enclosure MCB distribution board, double door with IP-43 protection single pole and neutral 240 volts, 4 way, including suitable size copper bus bar and neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed.

S&F in replacement sheet metal enclosure MCB distribution board, double door with IP-43 protection single pole and neutral 240 volts, 12 way, including suitable size copper bus bar and neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed.

S&F in replacement sheet metal enclosure MCB distribution board, double door with IP-43 protection TPN 415 Volts, 4 way, including suitable size copper bus bar and metal door, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed.

S&F in replacement sheet metal enclosures distribution boards, double door three phase 415 volts 4 ways vertical TPN DB for comprising three phase four wire 200 Amp rated copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following (a) MCCB four pole 100 Amps AC 415 Volts 25 KA - 01 No. as incoming (b) 12 Nos. MCB SP 40 Amps, C curve rupturing capacity 10 KA as outgoing Note :- (i) The DB shall be flush fixed and making good the disturbed surface matching with existing specifications. (ii) All connection of the MCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped. (iii) All vacant holes of the DB shall be provided with blank plates of appropriate size. (iv) Double continuous earth wire shall be provided for each three phase DB from earthing mains dolly (v) MCB's should have a same make as of DB.

S & F in replacement of MCB single pole 240 volts, 'C' curv of rating from 6 to 32 amps, with rupturing capacity 10 KA,including providing thimble for out going cables.

S & F in replacement of MCB single pole 240 volts, 'B' curv of rating from 63 amps, with rupturing capacity 10 KA,including providing thimble for out going cables.

S & F in replacement MCB SPN 240 volts, 'C' curv of rating from 63 amps, with rupturing capacity 10 KA,including providing thimble for out going cables.

S & F in replacement MCB SPN 240 volts, 'C' curv of rating from 6 to 32 amps, with rupturing capacity 10 KA,including providing thimble for out going cables.

S&F in replacement MCB TPN 240 volts, 'C' curve of rating from 40 to 63 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement MCB TPN 240 volts, 'C' curve of rating from 100 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

M&L for taking down carefully existing ceiling fan/exhaust fan for greasing / oiling of ball bearings / bushes and making it for smooth and noise free operation and painting with Hi-Gloss synthetic enamel paint of approved shade by spray painting after filling cavaties and re-fixing after providing new fan clamp, nuts/bolts, washers, down rod as required and provision of 3 core copper flexible cable of size 1.0 Sqmm from ceiling rose to fan connector complete with writing of MES No. on the fan surface all as specified and directed.

S&F in replacement MCCB 63 Amps 415 volts, 50 Hz, 4 pole 16 KA breaking capacity including providing thimbles for out going cable /sprade link for incoming cable with nut bolts complete all as specified and directed.

S&F in replacement MCCB 100 Amps 415 volts, 50 Hz, 4 pole 16 KA breaking capacity including providing thimbles for out going cable /sprade link for incoming cable with nut bolts complete all as specified and directed.

S & F in replacement of existing unsv/ broken bakellite sheet cover 3 mm thick of size 5"x5" all as required at site including drilling holes for fixing screws and providing 4 Nos screws with washers for fixing the sheet to sunken box /wooden box.

S & F in replacement of existing unsv/ broken bakellite sheet cover 3 mm thick of size 7"x4" all as required at site including drilling holes for fixing screws and providing 4 Nos screws with washers for fixing the sheet to sunken box /wooden box.

S & F in replacement of existing unsv/ broken bakellite sheet cover 3 mm thick of size 7"x10" all as required at site including drilling holes for fixing screws and providing 4 Nos screws with washers for fixing the sheet to sunken box /wooden box.

S&F in replacement of anodise press steel sunk box of existing size having thickness not less than 1.6 mm for switches and sockets, cutting chiseling for concealed box and making good disturbed surface area and white wash/colour wash to matching with the existing colour and all as specified .

Dismantling of existing meter panel board removing existing energy meter keeping safe custody and Design, Supply, installation, testing and commissioning of indoor type wall mounting size min (1280X 775X245), Polycarbonate CPRI approved OEM made Meter Panel. The panel shall be made of modular POLYCARBONATE THERMOPLASTIC ENCLOSURES which should be UV resistance in accordance with IEC 61439-1, clause 10.2.4: The panel type wall mounted on mounting structure RAL 7016. The meter panel should be anti-acid & anti corrosive & fully transparent Door for meter vision. Degree of protection against mechanical load should be IK08 (5 Joule) in accordance with IEC 62262. The manufacturer of panel shall submit a copy of CPRI test report in polycarbonate only degree of ingress protection IP65 in accordance with IEC 60529. The gasket should be internally embedded made of polyurethane and enclosure make. The manufacturer of board/panel shall submit a copy of type test report of a board made out of Polycarbonate thermoplastic panel in accordance with IEC 60439-1. The CPRI test report shall have mention of following tests performed and passed out satisfactorily: Temperature Rise, Dielectric Properties, Short circuit withstand current – Rated peak & short time withstand current and Rated Conditional Short Circuit Current, Effectiveness of Protective Circuits. The board manufacturer must submit the copy of type test reports for Polycarbonate Thermoplastic Board only. Test Reports submitted of other material of construction like MS, SS will not be applicable.. The panel should passed glow wire test 960oC in accordance with 60695-2-11 flame retardant and self-extinguishing complete all as directed with and incl the following (a) Provision for existing electric energy meter - 04 nos in separate chamber with locking arrangement. (a) Four pole MCCB 63 Amps with breaking capacity 16 KA having fixed thermal and fixed magnetic release and spreader link at both incoming and incoming side - 01 No. (b) MCB DP 32 Amp 10 KA , C Curve - 4 Nos (To be connected with 4 Nos Meters) (c) MCB DP 06 Amp 10 KA, C Curve - 1 No (For common lighting + Bldg Security Lights) (d) Ten Nos terminal blocks provided for output supply. (e) MCCB/MCB Nos Operated by flip Cover (f) LED Indicating lamp - 03 Nos. (g) Internal wiring with 1100Volt grade 6.0 Sqmm FRLS PVC insulated multi flexible copper wire of sizes duly crimped with copper lugs of suitable size & type . Note : Re-fixed the energy meter in this new meter cabinet including all necessary electrical connection.

S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4 sqmm nominal cross sectional area and one run of 4 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 20 mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 6 sqmm nominal cross sectional area and one run of 6 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 20 mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

M&L for earthing complete with galvanised steel plate electrode 600mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mts deep below ground level with top edge of the plate not less than 1.50 Mtrs below ground level connected to glavanised iron Wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified incl 15 mm GI tubing medium grade and necessary fitting for protection of GI wire incl laying of charcoal dust and common salt in alternate layer, PCC Pit (1:3:6) type C-1 using 20 mm graded stone aggregate, RCC cover 40mm thick (1:2:4) type B-0 using 12.5 mm graded stone aggregate reinforced with 6 mm dia round bar @ 75 mm C/C both ways with MS handle 8 mm dia, plastering 15 mm thick CM (1:6) externally upto 150mm below ground level , GI funnel with 20mm dia medium grade GI pipe for watering and wire mesh incl excavation and earth work and disposal of surplus soil complete all as specified and shown on electrical plate No 3 of SSR Part (2009) and connected to earth test point incl testing and marking Bldg Nos and writing Test Results on a 3.0 mm thick painted M.S. earth pit marking Plate (200mm x 100mm) duly welded with a 450 mm long 10 mm dia round M.S. rod, fixed with the earth pit chamber by grouting complete including taking out old unserviceable earthing system including demolishing old earth pit chambers and removing of debris from the site with levelling the ground all as specified an directed.