Military Engineer Services Tender

Supply and filling fine ganga sand to the full width of trench for cushioning of cable for cable protection including spreading and punning down complete all as specified and directed

M&L for well burnt old size bricks, sub class B brick laid dry flat with width equal to length of whole brick, as cable protection complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified.

M&L for PCC (1: 2:4) type B-1 (using 20mm graded crushed stone aggregates ) as in stay filling or pole coping etc including necessary form work for rough finished surfaces complete all specified and directed.

S&F in replacement of GI tubing light grade 50mm dia with all fittings laid in trenches/fixed on wall/ceiling including dismantling of old pipe etc all as specified and directed.

S&F in replacement of GI tubing light grade 80mm dia with all fittings laid in trenches/fixed on wall including dismantling of old pipe etc all as specified and directed.

M&L for double walled corrugated DWC HDPE pipe of outer dia 50mm and inner dia 38mm including 90 degree bends with coupler and rubber ring laid in trenches of size 50mm suitable for cable protection of size 2 core 10 sqmm to 3.5 core 50sqmm cable complete all as specified and directed.

S & F in repairs security light brackets with 1.50mtrs long 40/50mm dia light grade galvanised iron pipe with 30° bend including flat iron clamps, nuts, bolts and washers to brace the same properly duly painted with two coats of silver coloured synthetic enamel paint over one coat of red oxide primer and making the good to disturbed surfaces to match with existing, complete all as specified and directed.

S&F in repair FRP looping box 350 x270x 200 mm with locking arrangement, shockproof and rustproof, rot-proof and termite resistance, cable entry from bottom and side, 100% weather proof for outdoor installation suitable for pole mounting, tamper proof, restricts unauthorised tapping, IS 11731, IP 66/67 suitable for 16-35 sqmm 3.5 core aluminium cable including 1 No MCB 6 Amp, 04 Nos aluminium bus bars of suitable size mounted on epoxy insulators with holes for incoming and outgoing cables and connector block two way and fixing with flat aluminium clamps not less than 25 mm x 3 mm with suitable size nuts, bolts and washers inside and outside looping box complets as directed.

Supply, installation, comissioning and teasting in replacement of out door type LT panel of approved make, CPRI approved, make, fabricated out of 3.15mm thick CRCA steel sheet powder coated, double door with and incl MS angle iron (40x40x6mm) base frame, cubical type mounted, dust and vermin proof, both side open and locking arrangement, danger board plate,Cable gand, bottom with detachable plates, front and rear with hinged type door and locking arrangements, chamber for cable entry and exit,chamber for aluminium bus bars including aluminium busbars 4 Nos,1200 Amp on phase & neutral, 415 volts, properly insulated aluminium bus bar capacity insulated with colored PVC sleeves mounted on suitable insulators and separators, holes drilled for connections including panel shall be mounted on brick work plate from of size 250x400x600mm in two nmber duly plasterd and PCC coping work om top surface height shall be .6. mtr above the GL and 0.40 mtr all aroung the FPB complete all as specified and comprising of the followings:-

INCOMING :-(a) MCCB thermal magnetic released, 4 Pole, 415 V,800 Amps with breaking capacity 65 KA , - 01 No (Main supply Incoming from Substation 09) OUTGOING :- (b) MCCB 4 Pole, 415 V, adjustable thermal setting 400 Amps with breaking capacity 36/35 KA - 01 No. for panel No 04 (c) MCCB 4 Pole, 415 V, adjustable thermal setting 630 Amps with breaking capacity 65 KA - 01No. for Panel No 03 (d) MCCB 4 Pole, 415 V, adjustable thermal setting 320 Amps with breaking capacity 35/36 KA - 01No. for Panel No 02 (e) MCCB 4 Pole, 415 V, adjustable thermal setting 63 Amps with breaking capacity 10 KA - 01No for MT Detail (f) MCCB 4 Pole, 415 V, adjustable thermal setting 40 Amps with breaking capacity 10 KA - 03No for Canteen, VIP vehicle bay and New Const bldg (g) MCCB 4 Pole, 415 V, adjustable thermal setting 200 Amps with breaking capacity 25 KA - 01No for MIG chock near DSC line panel (h) Voltmeter, electronic, digital type, with selector switch 0 - 500 volts, AC, 50 Hz - 1 No. (j) Ammeter electronic, digital type, 0 - 400 amps, AC, 50 Hz - 1 No. (k) Current transformer 200 / 5 amps rating, AC, 50 Hz - 3 Nos. (l) Phase indication LED lamps - 3 Nos (RYB).

Supply, installation, comissioning and teasting in replacement of out door type LT panel of approved make, CPRI approved, make, fabricated out of 3.15mm thick CRCA steel sheet powder coated, double door with and incl MS angle iron (40x40x6mm) base frame, cubical type mounted, dust and vermin proof, both side open and locking arrangement, danger board plate,Cable gand, bottom with detachable plates, front and rear with hinged type door and locking arrangements, chamber for cable entry and exit,chamber for aluminium bus bars including aluminium busbars 4 Nos,480 Amp on phase & neutral, 415 volts, properly insulated aluminium bus bar capacity insulated with colored PVC sleeves mounted on suitable insulators and separators, holes drilled for connections including panel shall be mounted on brick work plate from of size 250x400x600mm in two nmber duly plasterd and PCC coping work om top surface height shall be .6. mtr above the GL and 0.40 mtr all aroung the FPB complete all as specified and comprising of the followings:-

INCOMING :-(a) MCCB 4 Pole, 415 V, adjustable thermal setting 320 Amps with breaking capacity 35/36 KA - 01 No incoming for Panel No 01. OUTGOING :- (b) MCCB 4 Pole, 415 V, adjustable thermal setting 63 Amps with breaking capacity 10 KA - 03 No for Fuel pump, MTR & S section & SPR (c) MCCB 4 Pole, 415 V, adjustable thermal setting 40 Amps with breaking capacity 10 KA - 01 No. SPR (d) MCCB 4 Pole, 415 V, adjustable thermal setting 125 Amps with breaking capacity 25 KA - 01 for Panel No 08 (e) MCCB 4 Pole, 415 V, adjustable thermal setting 250 Amps with breaking capacity 25 KA - 01 for Panel No 07 (f) Voltmeter, electronic, digital type, with selector switch 0 - 500 volts, AC, 50 Hz - 1 No (g) Ammeter electronic, digital type, 0 - 400 amps, AC, 50 Hz - 1 No. (h) Current transformer 200 / 5 amps rating, AC, 50 Hz - 3 Nos. (j) Phase indication LED lamps - 3 Nos (RYB).

Supply, installation, comissioning and teasting in replacement of out door type LT panel of approved make, CPRI approved, make, fabricated out of 3.15mm thick CRCA steel sheet powder coated, double door with and incl MS angle iron (40x40x6mm) base frame, cubical type mounted, dust and vermin proof, both side open and locking arrangement, danger board plate,Cable gand, bottom with detachable plates, front and rear with hinged type door and locking arrangements, chamber for cable entry and exit,chamber for aluminium bus bars including aluminium busbars 4 Nos, 750 Amp on phase & neutral, 415 volts, properly insulated aluminium bus bar capacity insulated with colored PVC sleeves mounted on suitable insulators and separators, holes drilled for connections including panel shall be mounted on brick work plate from of size 250x400x600mm in two nmber duly plasterd and PCC coping work om top surface height shall be .6. mtr above the GL and 0.40 mtr all aroung the FPB complete all as specified and comprising of the followings:-

INCOMING :-(a) MCCB 4 Pole, 415 V, adjustable thermal setting ,500 Amps with breaking capacity 65 KA - 01 No Incoming from Panel 01 OUTGOING :- (b) MCCB 4 Pole, 415 V, adjustable thermal setting 400 Amps with breaking capacity 35/36 KA - 01 No. for feeding to panel 09 (c) MCCB 4 Pole, 415 V, adjustable thermal setting 40 Amps with breaking capacity 10 KA - 02 No for POL store & MT store (d) MCCB 4 Pole, 415 V, adjustable thermal setting 63 Amps with breaking capacity 10 KA - 03 No for MT office, Station MTR section & SPR (e) Voltmeter, electronic, digital type, with selector switch 0 - 500 volts, AC, 50 Hz - 1 No (f) Ammeter electronic, digital type, 0 - 400 amps, AC, 50 Hz - 1 No. (g) Current transformer 200 / 5 amps rating, AC, 50 Hz - 3 Nos. (h) Phase indication LED lamps - 3 Nos (RYB).

Supply, installation, comissioning and teasting in replacement of out door type LT panel of approved make, CPRI approved, make, fabricated out of 3.15mm thick CRCA steel sheet powder coated, double door with and incl MS angle iron (40x40x6mm) base frame, cubical type mounted, dust and vermin proof, both side open and locking arrangement, danger board plate,Cable gand, bottom with detachable plates, front and rear with hinged type door and locking arrangements, chamber for cable entry and exit,chamber for aluminium bus bars including aluminium busbars 4 Nos, 600 Amp on phase & neutral, 415 volts, properly insulated aluminium bus bar capacity insulated with colored PVC sleeves mounted on suitable insulators and separators, holes drilled for connections including panel shall be mounted on brick work plate from of size 250x400x600mm in two nmber duly plasterd and PCC coping work om top surface height shall be .6. mtr above the GL and 0.40 mtr all aroung the FPB complete all as specified and comprising of the followings:-

INCOMING :-(a) MCCB 4 Pole, 415 V, adjustable thermal setting ,400 Amps with breaking capacity 36/35 KA - 01 No incoming from Panel -01 OUTGOING :- (b) MCCB 4 Pole, 415 V, adjustable thermal setting 160 Amps with breaking capacity 25 KA - 02 No for Panel No-06 & Panel No-05 (c) MCCB 4 Pole, 415 V, adjustable thermal setting 40 Amps with breaking capacity 10 KA - 02 No for Light bay & MT pool (d) MCCB 4 Pole, 415 V, adjustable thermal setting 63 Amps with breaking capacity 10 KA - 02 No for S/L and SPR (e) MCB TPN, 415 V, 10KA 32 Amps - 01No. for toilet bathroom (f) Voltmeter, electronic, digital type, with selector switch 0 - 500 volts, AC, 50 Hz - 1 No (g) Ammeter electronic, digital type, 0 - 400 amps, AC, 50 Hz - 1 No. (h) Current transformer 200 / 5 amps rating, AC, 50 Hz - 3 Nos. (j) Phase indication LED lamps - 3 Nos (RYB).

Supply, installation, comissioning and teasting in replacement of out door type LT panel of approved make, CPRI approved, make, fabricated out of 3.15mm thick CRCA steel sheet powder coated, double door with and incl MS angle iron (40x40x6mm) base frame, cubical type mounted, dust and vermin proof, both side open and locking arrangement, danger board plate,Cable gand, bottom with detachable plates, front and rear with hinged type door and locking arrangements, chamber for cable entry and exit,chamber for aluminium bus bars including aluminium busbars 4 Nos, 240 Amp on phase & neutral, 415 volts, properly insulated aluminium bus bar capacity insulated with colored PVC sleeves mounted on suitable insulators and separators, holes drilled for connections including panel shall be mounted on brick work plate from of size 250x400x600mm in two nmber duly plasterd and PCC coping work om top surface height shall be 0.60 mtr above the GL and 0.40 mtr all aroung the FPB complete all as specified and comprising of the followings:-

INCOMING :-(a) MCCB 4 Pole, 415 V, adjustable thermal setting ,160 Amps with breaking capacity 35/36 KA - 01 No incoming from Panel 04. OUTGOING :- (b) MCCB 4 Pole, 415 V, adjustable thermal setting 40 Amps with breaking capacity 10 KA - 04 No for 4 Ton V/bay/DI point, CFT & MBI bay/Store & bathroom, H/mast/SHC coach bay & Store 1&2/ School coach bay(c) MCCB 4 Pole, 415 V, adjustable thermal setting 63 Amps with breaking capacity 10 KA - 01 No SPR/SPR (d) Voltmeter, electronic, digital type, with selector switch 0 - 500 volts, AC, 50 Hz - 1 No (e) Ammeter electronic, digital type, 0 - 400 amps, AC, 50 Hz - 1 No. (f) Current transformer 200 / 5 amps rating, AC, 50 Hz - 3 Nos. (j) Phase indication LED lamps - 3 Nos (RYB).

Supply, installation, comissioning and teasting in replacement of out door type LT panel of approved make, CPRI approved, make, fabricated out of 3.15mm thick CRCA steel sheet powder coated, double door with and incl MS angle iron (40x40x6mm) base frame, cubical type mounted, dust and vermin proof, both side open and locking arrangement, danger board plate,Cable gand, bottom with detachable plates, front and rear with hinged type door and locking arrangements, chamber for cable entry and exit,chamber for aluminium bus bars including aluminium busbars 4 Nos, 300 Amp on phase & neutral, 415 volts, properly insulated aluminium bus bar capacity insulated with colored PVC sleeves mounted on suitable insulators and separators, holes drilled for connections including panel shall be mounted on brick work plate from of size 250x400x600mm in two nmber duly plasterd and PCC coping work om top surface height shall be 0.60 mtr above the GL and 0.40 mtr all aroung the FPB complete all as specified and comprising of the followings:-

INCOMING :-(a) MCCB 4 Pole, 415 V, adjustable thermal setting ,200 Amps with breaking capacity 25 KA - 01 No incomong from Panel -02 OUTGOING :- (b) MCCB 4 Pole, 415 V, adjustable thermal setting 40 Amps with breaking capacity 10 KA - 07 No. for Mandir, Mini coach, 3 ton bay, Crane bay, Crane bay-ii, Commputor room & Vehicle washing bay (c) MCCB 4 Pole, 415 V, adjustable thermal setting 63 Amps with breaking capacity 10 KA - 01 No SPR. (d) MCB TPN, 415 V, 10KA 32 Amps - 02 Nos for MIsc load (e) Voltmeter, electronic, digital type, with selector switch 0 - 500 volts, AC, 50 Hz - 1 No (f) Ammeter electronic, digital type, 0 - 400 amps, AC, 50 Hz - 1 No. (g) Current transformer 200 / 5 amps rating, AC, 50 Hz - 3 Nos. (h) Phase indication LED lamps - 3 Nos (RYB).

Supply, installation, comissioning and teasting in replacement of out door type LT panel of approved make, CPRI approved, make, fabricated out of 3.15mm thick CRCA steel sheet powder coated, double door with and incl MS angle iron (40x40x6mm) base frame, cubical type mounted, dust and vermin proof, both side open and locking arrangement, danger board plate,Cable gand, bottom with detachable plates, front and rear with hinged type door and locking arrangements, chamber for cable entry and exit,chamber for aluminium bus bars including aluminium busbars 4 Nos, 190 Amp on phase & neutral, 415 volts, properly insulated aluminium bus bar capacity insulated with colored PVC sleeves mounted on suitable insulators and separators, holes drilled for connections including panel shall be mounted on brick work plate from of size 250x400x600mm in two nmber duly plasterd and PCC coping work om top surface height shall be 0.60 mtr above the GL and 0.40 mtr all aroung the FPB complete all as specified and comprising of the followings:-

INCOMING :-(a) MCCB 4 Pole, 415 V, adjustable thermal setting ,125 Amps with breaking capacity 25 KA - 01 No incoming from Panel No-02 OUTGOING :- (b) MCCB 4 Pole, 415 V, adjustable thermal setting 40 Amps with breaking capacity 10 KA - 04 No. for Servicing bay, MT yard, SPR & Misc load (c) MCB TPN, 415 V, 10KA 32 Amps - 01No Misc Load/Street light. (d) Voltmeter, electronic, digital type, with selector switch 0 - 500 volts, AC, 50 Hz - 1 No (e) Ammeter electronic, digital type, 0 - 400 amps, AC, 50 Hz - 1 No. (f) Current transformer 200 / 5 amps rating, AC, 50 Hz - 3 Nos. (g) Phase indication LED lamps - 3 Nos (RYB).

Supply, installation, comissioning and teasting in replacement of out door type LT panel of approved make, CPRI approved, make, fabricated out of 3.15mm thick CRCA steel sheet powder coated, double door with and incl MS angle iron (40x40x6mm) base frame, cubical type mounted, dust and vermin proof, both side open and locking arrangement, danger board plate,Cable gand, bottom with detachable plates, front and rear with hinged type door and locking arrangements, chamber for cable entry and exit,chamber for aluminium bus bars including aluminium busbars 4 Nos, 600 Amp on phase & neutral, 415 volts, properly insulated aluminium bus bar capacity insulated with colored PVC sleeves mounted on suitable insulators and separators, holes drilled for connections including panel shall be mounted on brick work plate from of size 250x400x600mm in two nmber duly plasterd and PCC coping work om top surface height shall be .6. mtr above the GL and 0.40 mtr all aroung the FPB complete all as specified and comprising of the followings:-

INCOMING :-(a) MCCB 4 Pole, 415 V, adjustable thermal setting ,400 Amps with breaking capacity 50 KA - 01 No incoming from Panel No -03 OUTGOING :- (b) MCCB 4 Pole, 415 V, adjustable thermal setting 250 Amps with breaking capacity 35/36 KA - 01 No for Panel No-10. (c) MCCB 4 Pole, 415 V, adjustable thermal setting 160 Amps with breaking capacity 25 KA - 02 No For Panel No- 12 & 13 (d) MCB TPN, 415 V, 10KA 32Amps - 01No Misc Load (e) MCCB 4 Pole, 415 V, adjustable thermal setting 40 Amps with breaking capacity 10 KA - 02 No for Paint shop & POL office (f) MCCB 4 Pole, 415 V, adjustable thermal setting 150 Amps with breaking capacity 18 KA - 01 No SPR.( g) Voltmeter, electronic, digital type, with selector switch 0 - 500 volts, AC, 50 Hz - 1 No (h) Ammeter electronic, digital type, 0 - 400 amps, AC, 50 Hz - 1 No. (j) Current transformer 200 / 5 amps rating, AC, 50 Hz - 3 Nos. (k) Phase indication LED lamps - 3 Nos (RYB).

Supply, installation, comissioning and teasting in replacement of out door type LT panel of approved make, CPRI approved, make, fabricated out of 3.15mm thick CRCA steel sheet powder coated, double door with and incl MS angle iron (40x40x6mm) base frame, cubical type mounted, dust and vermin proof, both side open and locking arrangement, danger board plate,Cable gand, bottom with detachable plates, front and rear with hinged type door and locking arrangements, chamber for cable entry and exit,chamber for aluminium bus bars including aluminium busbars 4 Nos,300 Amp on phase & neutral, 415 volts, properly insulated aluminium bus bar capacity insulated with colored PVC sleeves mounted on suitable insulators and separators, holes drilled for connections including panel shall be mounted on brick work plate from of size 250x400x600mm in two nmber duly plasterd and PCC coping work om top surface height shall be 0.60 mtr above the GL and 0.40 mtr all aroung the FPB complete all as specified and comprising of the followings:-

INCOMING :-(a) MCCB 4 Pole, 415 V, adjustable thermal setting ,200 Amps with breaking capacity 35/36 KA - 01 No Incoming from Panel No -09 OUTGOING :- (b) MCCB 4 Pole, 415 V, adjustable thermal setting 40 Amps with breaking capacity 10 KA - 01 No for SWT motor. (c) MCB TPN, 415 V, 10KA 32 Amps - 02No Parking & DG set Room. (d) MCCB 4 Pole, 415 V, adjustable thermal setting 125 Amps with breaking capacity 25 KA - 01 No for Panel No-11.( e) MCCB 4 Pole, 415 V, adjustable thermal setting 63 Amps with breaking capacity 10 KA - 01 No SPR (f) Voltmeter, electronic, digital type, with selector switch 0 - 500 volts, AC, 50 Hz - 1 No (g) Ammeter electronic, digital type, 0 - 400 amps, AC, 50 Hz - 1 No. (h) Current transformer 200 / 5 amps rating, AC, 50 Hz - 3 Nos. (j) Phase indication LED lamps - 3 Nos (RYB).

Supply, installation, comissioning and teasting in replacement of out door type LT panel of approved make, CPRI approved, make, fabricated out of 3.15mm thick CRCA steel sheet powder coated, double door with and incl MS angle iron (40x40x6mm) base frame, cubical type mounted, dust and vermin proof, both side open and locking arrangement, danger board plate,Cable gand, bottom with detachable plates, front and rear with hinged type door and locking arrangements, chamber for cable entry and exit,chamber for aluminium bus bars including aluminium busbars 4 Nos, 150 Amp on phase & neutral, 415 volts, properly insulated aluminium bus bar capacity insulated with colored PVC sleeves mounted on suitable insulators and separators, holes drilled for connections including panel shall be mounted on brick work plate from of size 250x400x600mm in two nmber duly plasterd and PCC coping work om top surface height shall be 0.60 mtr above the GL and 0.40 mtr all aroung the FPB complete all as specified and comprising of the followings:-

INCOMING :-(a) MCCB 4 Pole, 415 V, adjustable thermal setting ,100 Amps with breaking capacity 25 KA - 01 No incoming from Panel 10 OUTGOING :- (b) MCCB 4 Pole, 415 V, adjustable thermal setting 63 Amps with breaking capacity 10 KA - 01 No for pump house (c) MCB TPN, 415 V, 10KA 32 Amps - 02No Misc load (d) MCCB 4 Pole, 415 V, adjustable thermal setting 40 Amps with breaking capacity 10 KA - 01 No SPR (d) Voltmeter, electronic, digital type, with selector switch 0 - 500 volts, AC, 50 Hz - 1 No (e) Ammeter electronic, digital type, 0 - 400 amps, AC, 50 Hz - 1 No. (f) Current transformer 200 / 5 amps rating, AC, 50 Hz - 3 Nos. (g) Phase indication LED lamps - 3 Nos (RYB).

Supply, installation, comissioning and teasting in replacement of out door type LT panel of approved make, CPRI approved, make, fabricated out of 3.15mm thick CRCA steel sheet powder coated, double door with and incl MS angle iron (40x40x6mm) base frame, cubical type mounted, dust and vermin proof, both side open and locking arrangement, danger board plate,Cable gand, bottom with detachable plates, front and rear with hinged type door and locking arrangements, chamber for cable entry and exit,chamber for aluminium bus bars including aluminium busbars 4 Nos,150 Amp on phase & neutral, 415 volts, properly insulated aluminium bus bar capacity insulated with colored PVC sleeves mounted on suitable insulators and separators, holes drilled for connections including panel shall be mounted on brick work plate from of size 250x400x600mm in two nmber duly plasterd and PCC coping work om top surface height shall be 0.60 mtr above the GL and 0.40 mtr all aroung the FPB complete all as specified and comprising of the followings:-

INCOMING :-(a) MCCB 4 Pole, 415 V, adjustable thermal setting ,100 Amps with breaking capacity 25 KA - 01 No incoming from Panel No-09 OUTGOING :- (b) MCCB 4 Pole, 415 V, adjustable thermal setting 40 Amps with breaking capacity 10KA - 03 No for PUC centre, Vehicale servicing bay & SPR (c) MCB TPN, 415 V, 10KA 32 Amps - 01 No for Misc Load (d) Voltmeter, electronic, digital type, with selector switch 0 - 500 volts, AC, 50 Hz - 1 No (e) Ammeter electronic, digital type, 0 - 400 amps, AC, 50 Hz - 1 No. (f) Current transformer 200 / 5 amps rating, AC, 50 Hz - 3 Nos. (g) Phase indication LED lamps - 3 Nos (RYB).

Supply, installation, comissioning and teasting in replacement of out door type LT panel of approved make, CPRI approved, make, fabricated out of 3.15mm thick CRCA steel sheet powder coated, double door with and incl MS angle iron (40x40x6mm) base frame, cubical type mounted, dust and vermin proof, both side open and locking arrangement, danger board plate,Cable gand, bottom with detachable plates, front and rear with hinged type door and locking arrangements, chamber for cable entry and exit,chamber for aluminium bus bars including aluminium busbars 4 Nos,240 Amp on phase & neutral, 415 volts, properly insulated aluminium bus bar capacity insulated with colored PVC sleeves mounted on suitable insulators and separators, holes drilled for connections including panel shall be mounted on brick work plate from of size 250x400x600mm in two nmber duly plasterd and PCC coping work om top surface height shall be 0.60 mtr above the GL and 0.40 mtr all aroung the FPB complete all as specified and comprising of the followings:-

INCOMING :-(a) MCCB 4 Pole, 415 V, adjustable thermal setting ,160 Amps with breaking capacity 25 KA - 01 No Incoming from Panel -09 OUTGOING :- (b) MCCB 4 Pole, 415 V, adjustable thermal setting 100 Amps with breaking capacity 18KA - 02 No for Workshop & SPR (c) MCB TPN, 415 V, 10KA 32 Amps - 02 No for Washing Point & H/mast (d) MCCB 4pole, 415 V, 10KA 40 Amps - 01 No for M/s (e) Voltmeter, electronic, digital type, with selector switch 0 - 500 volts, AC, 50 Hz - 1 No (f) Ammeter electronic, digital type, 0 - 400 amps, AC, 50 Hz - 1 No. (g) Current transformer 200 / 5 amps rating, AC, 50 Hz - 3 Nos. (h) Phase indication LED lamps - 3 Nos (RYB).

Supply, installation, commissioning and testing in replacement of LT feeder piller box outdoor type, IP 54 protection made out of 3.15mm thick CRCA sheet metal, double door type and sitable MS angle iron base frame, cubical type floor mounted 3 phase 4 wire, 415V properly insulated aluminium bus bar-04 Nos having capacity 375 Amps on phase and neutral, dustand vermin proof, both side open with locking arrangement, danger board plate, duly painted internally and externally with powder coated, RYB indication lamp with Digital multifunction meter, suitable size platf built with brick work in CM (1:4) 15mm thick plastering in CM (1:6), 0.6Mtrs height from GFL, incl lugs, gland , thimble and nut bolts etc electric connection complete etc all as specified and directed by Eng in Charge. Incoming and Outgoing : (i) MCCB 250 Amps, 25KA , 4P, 415V - 01 No, (ii) RYB inidication lamp (iii) Volt meter and Ammeter.

Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to galvanised iron strip 25×4mm means of bolts, nuts check nut & washers of galvanised iron or steel & connected to main switch including complete excavation and earth work in soft/loose soil and disposal of surplus soil to a distance not exc 50 meters, PCC Chamber (1:3:6) type C-2 precast RCC cover with frame, funnel wire mesh, 20mm bore light grade galvanised iron or steel pipe for water, charcoal or coke and salt in alternative layers of 15cm compacted thickness all round the earth electrode complete alll as shown in electrical plate No 3 of SSR part-I including welding with suitble electrode and testing complete all as directed. NOTE :- (i) Main earthing strip from earth plate electrodeto test point upto length of 7.5 mtrs length shall deem to be included in the unit rate quoted against this item. (ii) M&L Tubing GI med grade 40mm dia for protection of earthing strip and passing the Road/passes and etc.shall deemed to be included in the unit rate quoted against this item.

S&F in repair 1.5 Sqmm three core PVC insulated FRLS flexible copper conductor wire for street/security light terminal box , incl suitable size of bottle lugs etc complete all as specified and directed.

Supply , lay ,testing and commissioning of cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded Aluminium conductor of size 35 sqmm 3.5 core. laid in trench/ duct / along pole/wall etc including suitable size lugs, glands,Nut, bolts, washers & insulation tape etc making connection complete incl taking out ot old unsericeable/damaged cable complete etc all as specified directed. Note : The cost of thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it.

Description all as per item No.29 above but cross sectional area 10 Sqmm 4 core complete all as specified and directed.

Description all as per item No.29 above but cross sectional area 16 Sqmm 4 core complete all as specified and directed.

Description all as per item No.29 above but cross sectional area 25 Sqmm 3.5 core complete all as specified and directed.

Description all as per item No.12 above but cross sectional area 50 Sqmm 3.5 core complete all as specified and directed.

Description all as per item No.29 above but cross sectional area 70 Sqmm 3.5 core complete all as specified and directed.

Description all as per item No.29 above but cross sectional area 95 Sqmm 3.5 core complete all as specified and directed.

Description all as per item No.29 above but cross sectional area 120 Sqmm 3.5 core complete all as specified and directed.

Description all as per item No. 29 above but cross sectional area 185 Sqmm 3.5 core complete all as specified and directed.

Description all as per item No.29 above but cross sectional area 240 Sqmm 3.5 core complete all as specified and directed.

M&L for cutting of PCC/Hard standing /WBM road not exceeding 30cm in width and not exceeding 60 cm in depth for passing of LT cable and making good of disturbed surface to make with the existing surfaces by using old and new material upto 15cm in depth and providing 15cm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate finished fair and even complete all as specified and directed.

M&L for making horizantal boring 60cm deep below road crossing for passing of LT cable in suitable size GI pipe complete all as specified and directed by EIC.