Military Engineer Services Tender

S&F Plain, galvanised, mild steel sheeting, 1.00 mm thick in, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 fixed with self tapping screws as specified complete all as specified and directed.

M&L Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 for side wall for inserting roof sheet, complete all as specified and directed.

Dismantling of wrought iron of mild steel work of any description not otherwise poivided complete all as specified and directed.

S&F of Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, wind tie,channel or flat sections) including distance pieces, cleats etc Fe 410 -W (GdeE- 250) qualityA complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of old steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint at any height complete all as specified and directed

Taking out old u/s glass of any description, from old wooden or metal frames, or stone, concrete or brick surrounds, any thickness or size; hacking out old putty or removing beads etc, including making good breakages in taking out and removal from site complete all as specified and directed.

S&F Rough cast wired glass, 6.4mm thick not exc 0.5 Sqm each and glazing with oil putty in square, complete all as specified and directed.

Taking down cement or cemant lime plaster of any discription on bricks or stone walls/ceiling etc including racking out joints, hacking for kay, scrubbing down with water complete all as specified and directed.

M&L for 15mm thick plastering in CM 1:6 on brick surfaces of walls & finishing the surface even & smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick plastering in CM 1:4 on brick surfaces of walls & finishing the surface even & smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of cement base primer complete all as specified and directed.

M&L for two coats of oil bound distemper over and including a coat of average 1mm thick cement base wall care putty on new plastered surfaces after preparation of new surface complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins arches pillar, wall etc complete all as specified and directed.

M&L for brick work with subclass B bricks old size straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

Preparing old plastered or unplastered surfaces of walls by brooming down or by steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and applying two coats of oil bound distamper over and including a coat of average 1mm thick cement base wall care putty, complete all as specified and directed.

Material and Labour for preparation of old plastered or unplastered surfaces of wall including cornices, pilaster etc by brooming down by steel wire brushing, scrapping down smoke Soot, moulds, moss and trading oil and greasy spots etc and apply one coat of white wash complete as specified and directed.

M&L for preparing old plastered or unplastered surfaces of walls and applying one coat of cement base paint complete all as specified and directed.

S&F in repair PVC (SWR) pipes single socketed 200 mm bore, incl bend, shose, Tee, Y, as required, etc in any length with rubber ring joints fixed to walls with MS clamp all as specified and directed.

S&F in repair MS Sheet (1.25 mm thick) angle (internal or external ) or nozzle pieces 200 mm dia(outlets) complete all as specified and directed.

Taking down chowkats or frame with shutter (without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and directed.

S & F factory made steel ventilators with top hung shutter & glazing bars hinges, steel peg stay etc dovetailed or welded, size and thickness of members confirming to IS 1038 complete all as specified and directed.

S & F factory made steel windows with side hung shutters using steel section with glazing bars including box type hinge, 01 'Z' section handle, 02 Nos 100mm MS tower bolt, one steel peg stay etc in each leaf dovetailed or welded complete all as specified and directed.

S & F factory made steel windows with side hung shutters with using 'Z' steel section without glazing bars including box type hinges, 01 'Z' section handle, 02 Nos 100mm MS tower bolt, one steel peg stay etc in each leaf dovetailed or welded complete all as specified and directed.

M&L 3mm thick ordinary quality sheet glass and glazing with oil putty and clip pin in square not exc 0.5 Sqm in each pane complete all as specified and directed.

Supply & fix stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed in windows or along with 'F' section complete all as specified and directed.

M&L for providing, PCC 1:3:6 type C-1 (using 20mm graded aggregate) for embedding hold fasts including necessary form work etc.complete all as specified and directed.

M&L for vinyal flooring/epoxy , high density floor covering for battery charging room as per below specification. 1- class- Electrostatic conductive. 2- 02 mm thick, 3- size of tile 61x61 Cm 3- wear resistant -0.17 mm, 4- Fire resistent - B1/Q1 5- Heat Resistent - 0.011 Sqm K/W, 6 - Fire approoved certified complete all as specified and directed.

S&F Powder coated aluminium door & frame of wt 0.55 Kg/m incl- 5.00mm thick tinted glass in half portion and in other half portion 12 mm thick prelaminated particle board, exterior grade prelaminated one side with decorative choice lamination & other side balancing white lamination complete and fixed with anodized aluminium snap beading, glazing clips, joining clips, screws and 02Nos of aluminium handle on each door shutter, aluminium anodized tpwer bolt 200mm long 02 Nos on each shutter and martice lock device complete with double keys for each lock, 01 No Hydolic door closer for each shutter complete all as specified and directed with following specifications:- (a) Aluminium door frame = 101.50x44.45mm (b) Aluminium style/top & middle rails of shutter = 83.5x44.45mm (c) Aluminium bottom rail of shutter = 114.50x44.45mm (d) Aluminium door frame with shutters shall be fixed in position in brick wall opening as required according to site conditions including all fastening arrangements etc complete all as specified and directed

S&F of Anodised aluminium window shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/RM including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed

S&F aluminium partition of specified aluminium section wt of section not exc 0.55 kg/RM including aluminium beads rubber gasket and 5mm thick frosted glass in upper portion and 12 mm thick prelaminated particle board, exterior grade prelaminated one side with decorative choice lamination & other side balancing white lamination complete all as specified and directed.

M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

M&L for vitrified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc set and jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tiles including and over 15mm thick screed bed in CM 1:6.complete all as specified and directed.

M&L for vitrified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick incl and over cement screed bed 20 mm thick in 1:6 cement and sand mortrar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

Demolition of wall and ceiling board or insulation board / slabs / blanket any thickness including cover fillets complete all as specified and directed.

S&F in repair 605x605mm snap grid of powder coated galvanized iron of angle of size 23mm x 23mm of 30 gauge (Perimeter), T section of size 23mm x35mm main and 23mm x 27 mm (intermediate) of 30 gauge suitable for false ceiling including GI wire 4 mm thick @ 1200 mm centre to center both ways for hanging arragement coplete all as specified and directed

M&L for 4mm thick non asbestos fibre cement building board designer as in ceiling of size 600 x 600mm fixed to GI snap grid frame work complete all as specified & directed.

Fixing only 4mm thick non asbestos fibre cement building board designer as in ceiling of size 600 x 600mm fixed to GI snap grid frame work complete all as specified & directed.