Military Engineer Services Tender

One socket outlet point 3 pin 6 Amps on independent board controlled by one switch.

M&L for point wiring controlled by one switch with PVC unsheathed single core unsheathed single core FRLSH multistranded copper conductor cable IS-694 marked of size 2.5 Sqmm (nominal area) in and including stove enamelled steel conduit 20 mm dia by cutting chases in walls by cutter and making good the surface in CM 1:3 and to the original specification and stove enamelled steel conduit 20 mm dia ceiling for steel structure/surface with including cast iron/pressed steel terminal boxes including including one run of PVC insulated FRLSH copper conductor cable of 2.5 Sqmm with green insulation as earth dolly for 6 pin, 16 Amp socket outlet on Independent board.Note : (a) The height of the bldg is 8 Mtr and above, the contractor will provide safety equipment like ladder, safety belt, etc for point wiring.(b) Point wiring ceiling conduit should be fixed with clamp properly in same distance and discipline.

Supply and fixing switch flame proof rotary type with termination box LM-6, 16 Amp, Single pole 250 V, bottom cable entry 3" ET 2 Nos, construction material Aluminium Die cast for Gas group IIA, IIB, class zone 1 & 2 etc complete all as specified and directed by Engr-in-Charge.

Supply and fixing flame proof switch socket & plug combined in LM-6 cable termination box in LM6, 16 Amp, 250V, 2P+earth (3 Pin), cable entry of size 3/4" ET (BS) 2 Nos, construction material Aluminium Die cast for Gas group IIA, IIB, class zone 1 & 2 etc complete all as specified and directed by Engr-in-Charge.

Supply and fixing flame proof switch socket & plug combined in LM-6 cable termination box in LM6, 25 Amp, 250V, 2P+earth (3 Pin), cable entry of size 3/4" ET (BS) 2 Nos, Construction material Aluminium Die cast, class zone 1 &2, gas group IIA, IIB complete all as specified and directed by Engr-in-Charge.

S&F in repair for LED light fitting 1x16 Watt flame proof and IP 65 protection with die cast aluminum housing with heat resistant toughened glass with LED tube, light fixtures driver, holders, connector etc. complete with all accessories prewired and including connecting up with three core flexible copper conductor cable complete all as specified and directed by Engr-in-Charge.

S&F in repair for flame proof/weather proof LED light fitting 120 watt, 240 V, 50 Hz, 0.95 PF, 100 lumen per watt, surge protection 4 KVA, CCT 6000 to 6500 K, stainless steel 'O' ring endless neoprene rubber gasket, cable entries 3/4" ET-02 Nos, construction material Aluminium die cast LM-6 and IP 66 protection with die cast aluminum housing with heat resistant toughened glass with LED driver, connector etc. complete with all accessories prewired and including connecting up with three core flexible copper conductor cable complete all as specified and directed by Engr-in-Charge.

S&F in repair for flame proof/weather proof Bldg security light fitting 60 watt, 240V, 50 Hz, 0.95 PF, 100 Lumen per watt, Surge protection 4 KVA, CCT 6000 to 6500 K, stainless steel 'O' ring endless neoprene rubber gasket, cable entries 3/4" ET-02 Nos, construction material Aluminium die cast LM6, CIMFR & PESO certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 66 protection with die cast aluminum housing with heat resistant toughened glass with LED driver, connector etc. complete with all accessories prewired and including connecting up with three core flexible copper conductor cable complete all as specified and directed by Engr-in-Charge.

S&F in repair for flame proof recess mounted fitting 36 watt, 240 V, 50 Hz, 0.95 PF, 100 Lumen per watt, square type/round shape type, Surge protection 4 KVA, CCT 6000 to 6500 K, stainless steel 'O' ring endless neoprene rubber gasket, cable entries 3/4" ET-02 Nos, construction material Aluminium die cast LM6, CIMFR & PESO certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 66 protection with die cast aluminum housing with heat resistant toughened glass with LED driver, connector etc. complete with all accessories prewired and including connecting up with three core flexible copper conductor cable complete all as specified and directed by Engr-in-Charge.

S&F flame proof/weather proof wall mounted fan 18" 0.25 HP, single phase, RPM 1440, CFM 9000, Design confirm to Standard IS2148-2004 IEC60079-1(2001) & IS13346-2004 IEC 60079-0(2000), aluminium die cast, Light gray Epoxy Polyester Powder Coating Shade No 631and IP 66 complete all as directed by Engr-in-Charge.

Supply and installation of Air Ventilator (circulator) non power driven roof top Turbo ventilator stainless steel body of size 24", with suitable size of base polycarbonate type, including foam filler for filling of gap, surface powder coated, robustness and easy installation on roof complete including taking down old air ventilator with all accessories all as directed by Engr-in-charge.

Supply and fixing flame proof pedestal fan 0.25 HP, 240 Volts, 50 Hz, single phase, sweep size 18", adjustable type, fan speed 1440 RPM, mounting type, air flow 4000 CFM, Flameproof motor, Metal blade, standard with Flp double compresion cable gland, high speed air circulator, heavy duty motor, copper winding, base cast iron along with all accessories complete all as specified and directed by Engr-in-Charge.

Supply and fixing flame proof exhaust fan sweep size 18", 0.25 HP single phase single phase, RPM1440, Design confirm to Standard IS: 2148-2004 IEC: 60079-1(2001) & IS:13346-2004 IEC 60079-0(2000), aluminium body, Light gray Epoxy Polyester Powder Coating Shade No 631 Earthling, Internal - 01 No. External- 02 Nos, Cable Entry: 01 No. for ET Hardware In Stainless Steel and IP 65 complete all as directed by Engr-in-Charge.

S&F in repair for flame proof/weather proof distribution board SPN 12 way, lightening distribution panel with complete with Incoming MCB 63 Amp SPN, 240 Volts, 10 KA - 01 No, outgoing MCB SP 10 to 20 Amp, 240 Volts, 10 KA - 10 Nos, internal bus bar & wiring up to terminals, mild steel, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 with cable gland and stoping plug complete all as directed by Engr-in-Charge.

S&F in repair for flame proof/weather proof distribution board TPN 8 way lightening distribution panel with complete with MCCB 63 Amp, 4 pole, 415 volts, 16 KA - 01 No, MCB 32 Amp SP, 240 Volts, 10 KA - 24 Nos, internal bus bar & wiring up to terminals, mild steel, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 with cable gland and stoping plug complete all as directed by Engr-in-Charge.

M&L for sub main wiring with two single core 10.00 Sqmm (nominal area) PVC Insulated (FRLSH) unsheathed multi stranded copper conductor cable 1100 volts grade drawing through concealed stove enameled steel conduit 25 mm dia by cutting chases in wall by cutter and making good the disturbed surface in CM 1:3 and and steel stove conduit on ceiling for steel structure/surface steel conduit with clamps complete including 10.00 Sqmm PVC insulated unsheathed multi stranded (FRLSH) single core copper conductor cable for earth wire including taking down/removing old one and making good distrubed surfaces of walls, floors, etc complete all as specified and directed. Note : (i) Three runs of single core 10.00 Sqmm multi stranded copper cable including earth wire and stove enameled steel conduit 25 mm shall be measured as one run length (iii) Extra length of cable required for connection to DBs/MCBs shall deem to be included in unit rate quoted by contractor against the item (iv) Earth wire run inside the steel conduit.

M&L for sub main wiring with four single core 6.00 Sqmm (nominal area) PVC Insulated (FRLSH) unsheathed multi stranded copper conductor cable 1100 volts grade drawing through concealed stove enameled steel conduit 25 mm dia by cutting chases in wall by cutter and making good the disturbed surface in CM 1:3 and and steel stove conduit on ceiling for steel structure/surface steel conduit with clamps complete including 6.00 Sqmm PVC insulated unsheathed multi stranded (FRLSH) single core copper conductor cable for earth wire including taking down/removing old one and making good distrubed surfaces of walls, floors, etc complete all as specified and directed. Note : (i) four runs of single core 6.00 Sqmm multi stranded copper cable and one run of 6.00 Sqmm earth wire and stove enameled steel conduit 25 mm shall be measured as one run length (iii) Extra length of cable required for connection to DBs/MCBs shall deem to be included in unit rate quoted by contractor against the item (iv) Earth wire run inside the steel conduit.

M&L for sub main wiring with two single core 2.50 Sqmm (nominal area) PVC Insulated flame retardant unsheathed multi stranded copper conductor cable 1100 volts grade drawing through concealed stove enameled steel conduit 20 mm dia by cutting chases in wall by cutter and making good the distrub surface in CM 1:3 and and steel stove conduit on ceiling for steel structure/surface steel conduit with clamps complete including 2.50 Sqmm PVC insulated unsheathed multi stranded flame retardant single core copper conductor cable for earth wire including taking down/removing old one and making good distrubed surfaces of walls, floors, etc complete all as specified and directed. Note : (i) Two runs of single core 2.50 Sqmm multi stranded copper cable and one run of 2.50 Sqmm earth wire and steel conduit 20 mm shall be measured as one run length (iii) Extra length of cable required for connection to DBs/MCBs shall deem to be included in unit rate quoted by contractor against the item (iv) Earth wire run inside the PVC conduit.

M&L for sub main wiring with two single core 1.50 Sqmm (nominal area) PVC Insulated (FRLSH) unsheathed multi stranded copper conductor cable 1100 volts grade drawing through concealed stove enameled steel conduit 20 mm dia by cutting chases in wall by cutter and making good the distrub surface in CM 1:3 and and steel stove conduit on ceiling for steel structure/surface steel conduit with clamps complete including 1.50 Sqmm PVC insulated unsheathed multi stranded (FRLSH) single core copper conductor cable for earth wire including taking down/removing old one and making good distrubed surfaces of walls, floors, etc complete all as specified and directed. Note : (i) Two runs of single core 1.50 Sqmm multi stranded copper cable and one run of 1.50 Sqmm earth wire and stove enameled steel conduit 20 mm shall be measured as one run length (iii) Extra length of cable required for connection to DBs/MCBs shall deem to be included in unit rate quoted by contractor against the item (iv) Earth wire run inside the PVC conduit.

Taking down existing cable of any type (Signal telephone, Avan Network, etc cable) with existing PVC Conduit and refixing/relaying in new stove enamelled steel conduit 20 mm dia along with tee, elbow, etc accessories on ceiling for steel structure/surface conduit with clamps, gutties etc for steel structure complete with all fixing accessories. Note : Contractor's quoted rate shall deemed to be inclusive of stove enamelled steel conduit of size 20 mm dia.

S&F in repair for MCB single pole (SP) 06 to 20 Amp 240 Volts 10 KA 'B' series with all incoming/outgoing connection with proper size lugs complete all as specified and directed.

S&F in repair for MCB single pole and neutral (SP&N) 40 to 63 Amp 240 volts 10 KA 'C' series with all incoming/outgoing connections with proper size lugs complete all as specified and directed.

S&F in repair for MCB TPN 63 Amp, 240 volts, 10 KA 'C' series with all incoming/outgoing connections with proper size lugs complete all as specified and directed.

Taking down aluminium strip 25 x 3.15mm with necessary saddles / insulators and fixing screws etc from roof conductors and down conductors above the bldg complete all as specified and directed.

Taking down air termination single pointed aluminium rod 12mm dia, 300mm long complete all as specified and directed.

Taking down Galvanized iron strip 32 x 6 mm with necessary saddles / insulators and fixing screws etc from roof conductors and down conductors above the bldg complete all as specified and directed.

Taking down old unsv GI pipe 40 mm dia complete all as specified and directed.

S & F 8 mm Aluminum Round Conductor complete meeting the requirements of DIN EN 50164-2 (VDE 0185 part 202) & VDE 0185-305 (IS/IEC 62305) complete all as specified & directed.

S & F Roof conductor holder for sheet , Bottom section stainless steel (V2A) with bottom section Ø 8.5 mm slot made of Conductor holder of polyamide @ every 1mtr distance complete all as specified & directed.

S&F cross universal connector for T and cross connection, to route vertical down conductor /mesh formation made of hot dipped galvanised iron with necessary screws etc as required including installation with 4 hexagonal bolts M8*25 with M8 hexagonal nuts complete all as specified & directed.

S&F expansion piece with connector for equalising temperature related length changes with necessary on conductors length over 20 meters, for round conductor Rd 8/ALU complete all as specified & directed.

S&F T cross and parallel connectors & quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised & conforming to the requirements according to DIN VDE 0185-305 (IS-IEC 62305)(2nos/expansion piece ) complete all as specified & directed.

S & F Polyamide Roof conductor holder for parapet with M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder, weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance complete all as specified & directed.

S&F Test Joint (Folding Clamp) made of SS,suitable to connect 8mm round conductor and max by 30x3 mm GI strip as specified in drawing complete all as specified & directed.

S & F Galvanised Steel Flat 30X3 mm thickness from earth electrode directly in ground as required, flat conductor shall be of Hot Dipped & Cross sectional area of 90mm square according to DIN EN 50164-2 (VDE 0185 part 202) with meeting the requirement of VDE0185/305(IS-IEC 62305) Zinc coating: 500 g/m square (Approx :70 micron coating) should be tested and used exclusively for lightning protection earthing system and ring equipotential bonding complete all as specified & directed.

S & F Cross connector for Flat with out adaptor plate FT suitable for FL 30mm x FL 30 mm or max FL 40 mm x FL 40 mm without adapter plate Galvanised steel strip & installation with 4 nos of hexagonal plate size M8 x 25 and 4 hexagonal nuts M8 (F) complete all as specified & directed.

S & F flat conductor holder suitable for FL 30 & Installation with 2 hexagonal bolts complete all as specified & directed.

S & F Plastic Corrosion Protection strip of approx 1.1 mm thick, width 50mm made of petrolatum- coated chemical fibre fabric complete all as specified & directed.

S & F UL Listed & CPRI Tested maintenance free ,Low carbon copper coated earth rod of 3 metre electrode having diameter of 17.2 mm with copper coating thickness of 250micron tested as per IEC 62561-2 including taking down old one complete all as specified & directed.

S&F Universal clamp made of SS to connect rod with flat conductor including taking down old one complete all as specified & directed.

S&F Earth conductivity enhancing compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested complete all as specified & directed.

S&F Heavy duty earth champers of 5000kg load bearing capacity to ensure the safety of earthing system complete all as specified & directed.

M&L fabrication, installation sign board indentifier / marker ( 30cm x 20cm board Preferably metallic in Oval shape) of 22 SWG and stand of made out of angle iron of size 40 x 40 x 6mm thick of length 90cm (60 cm above ground level) and duly painted with two coat of syenthetic enamel paint of YELLOW colour for background over a coat of red oxide primer and marked 'LA' letters of size 1 inch height in black paint text as directed and to be grouted 2 feet from the ground level including all excavation and earth work. It will mention the type of earthing, number of the earth pit and the total number of particular type of earthing for that building equipment. For example, a lightening earth pit can be marked as LA 1/18 which means lightening arrester EP No 1 out of 18 LA earth pits for the building complete all as specified and directed.

M&L for GI tubing light grade 40 mm dia of bore with all fitting laid or fixed on roof top across the bldg as site with required fixing accessories complete all as specified and directed.

M&L for re-fixing to aluminium/ galvanised strip 25 x 3.15mm in any size fixing on saddle type insulators using broung nut bolts and washer etc/ reveting by aluminium reveits for jointing to strip/ laid in trench/ fix on surface of wall/ beam etc as site required making circuit continuty with making straight all as directed. Note ; Quoted rate shall be including cost saddle type insulator, nut bolts, and washers, etc etc all (ii) Porcelain type insulator and fixing screws shall be provided @ 3 Nos per RM for fixing of strip.

M&L for re-fixing to galvanised strip 32 x 6 mm in any size fixing on saddle type insulators using broung nut bolts and washer etc/ reveting by aluminium reveits for jointing to strip/ laid in trench/ fix on surface of wall/ beam etc as site required making circuit continuty with making straight all as directed. Note ; Quoted rate shall be including cost saddle type insulator, nut bolts, and washers, etc etc all (ii) Porcelain type insulator and fixing screws shall be provided @ 3 Nos per RM for fixing of strip.

Fixing only Air termination single pointed aluminium rod 12 mm dia and 300 mm long complete all as specified and directed. Note ; Quoted rate shall be including cost of all required material and accessories

Supply, Install, Testing and Commissioning of Inverter split Air conditioner capacity 1.50Ton, units indoor and outdoor complete with cordless remote control unit, with cooling function,3M micro protection filter/Anti bacterial filter high air flow with low noise (up to 36 db), (Dual protection filter)Auto Air swing, Star rating 5 Star and ISEER value more than 5.00, Rotary type compressor of capacity 1.50 Ton, Refrigerant R-410A, copper type condensor coil, Power Supply 220-240 Volts, Single Phase, 50 Hz complete all as directed by Engr-in-Charge.

Supply, installation and testing of wall mounted voltage stabilizer of capacity 5 KVA, input working range 160 V to 270 V, output working range 200 V to 240 V +- 5%, metal cabinet material, multifunctional digital display, automatic low & high cut off, initial time delay, auto start including wall mounting accessories complete all as directed by Engr-in-Charge.

Supply & fix sheet metal enclosure single pole and neutral with a two pin, earth plug and socket complete with one MCB 20 Amp single pole 10 KA 240 volts complete all as specified and directed by Engr-in-Charge.

Supply and install heavy duty walll mounted bracket suitable for installation of Split air conditioner outdoor unit of capacity up to 2.00 Ton, bracket weight 3.2 Kgs including fastner, nut bolt, etc including all accessories complete all as directed by Engr-in-Charge.

Excavation in trenches in soft/loose soil not exceeding 1.50 m wide and not exceeding 1.50 m in depth for laying of cables and getting out including trimming of sides complete all as specified and directed.

Returing, filling in, including spreading, leveling watering and well ramming in layers not exceeding 25 cm thick each layer compete all as specified and directed.

Removal of surplus soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.50 m above the starting point complete all as specified and directed.

Material and labour for sand cushioning with a layer of sand 8 cm thick before laying of cable and 15 cm thick after laying of cable in trenches complete all as specified. Note: Punned thickness shall be measured for payment.

Supply and laying old size sub class 'B' bricks laid flat in trenches over the cable with the length of brick perpendicular to the direction of cable length, adjacent/abutting each other for cable protection complete all as specified and directed.

Labour only for reuse of serviceable bricks obtained from excavation of taking down cable of various sizes complete all as specified and directed.

Material & labour for cutting /boring to plinth protection/ hard standing / road etc in suitable depth to across the GI pipe size upto 80 mm dia of bore for drawn through XLPE under ground cable for giving mechanical protection to cable complete all as directed. (Note : Quoted rate shall include the cost of required material for repairing to disturbed surface complete all as per existing site and all as directed by Engineer-in-charge.

Supply and laying 80 mm bore galvanized steel tubing "light grade" with all fittings,clamps, bolts, nuts and washers (ISI Marked) and fixing to the pole complete with all fittings, laid in trenches/fixed complete to wall and ceiling or laid in floors including taking down old one complete all as specified and directed.

Taking down old unserviceable LT cable any size and remove from site complete all as specified and directed.

Supply, laying, jointing, connecting and testing XLPE insulated PVC sheathed cable 1100V grade, conforming to IS-7098 (Part-I) of 1988, screened PVC bedded, armoured electric power cable, heavy duty multi-stranded aluminium conductor grade cross section area 3.5 core 70 Sqmm (earthed) complete all as specified, laid in trenches / fixed on walls/poles, passing through pipes, etc. including connecting up to DBs, etc. with required lugs, end terminal / cable glands including taking out/down old unserviceable cable and disposing off complete all as specified and as directed of the following sizes: Note: Excavation and earthwork will be measured and paid separately under respective items herein

Supply, laying, jointing, connecting and testing XLPE insulated PVC sheathed cable 1100V grade, conforming to IS-7098 (Part-I) of 1988, screened PVC bedded, armoured electric power cable, heavy duty multi-stranded aluminium conductor grade cross section area 3.5 core 25 Sqmm (earthed) complete all as specified, laid in trenches / fixed on walls/poles, passing through pipes, etc. including connecting up to DBs, etc. with required lugs, end terminal / cable glands including taking out/down old unserviceable cable and disposing off complete all as specified and as directed of the following sizes: Note: Excavation and earthwork will be measured and paid separately under respective items herein

M&L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick surrounded with charcoal and salt, buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead using GI earth strip in size 32 x6 mm means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth strip protected by galvanized iron 40 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade with funnel including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete including taking out old unsv earthing all as directed by Engineer in Charge. (i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I (ii) Item includes the cost of 7.50m GI pipe and protection of earth strip. (iii) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate. Note: Quoted rate shall be paid after getting resistance value satisfactorily (below 2.00 Ohm) and record will be submitted by the contractor.

M&L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick surrounded with charcoal and salt, buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead using GI earth wire in size 4 mm dia means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth strip protected by galvanized iron 15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade with funnel including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete including taking out old unsv earthing all as directed by Engineer in Charge. (i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I (ii) Item includes the cost of 7.50m GI pipe and protection of earth strip. (iii) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate. Note: Quoted rate shall be paid after getting resistance value satisfactorily (below 2.00 Ohm) and record will be submitted by the contractor.

Supply, install, testing and commissioning of LT panel size 100 cm x 80 cm x 40 cm enclosures cubical weather and vermin proof totally enclosed made out of 3.15 mm thick CRCA sheet machine pressed of suitable size to operate on 3 phase 4 wire system 415 Volts, 50HZ double door with front and rear openable with locking arrangement incl inner shutters for mounting switch gear etc, bottom gland plate with sufficient numbers of circular cable entry holes, including PCC work, prewired complete duly powder coated with comprising of the following including taking down old panel :- INCOMING: (i) MCCB 100 Amp ,415 Volt,25 KA, 4 pole, with thermal & magnetic release rated, rated Ultimate Shortcircuit Breaking Capacity Icu at 415 V (kA rms) Vac (kA rms), Rated Service short circuit Breaking Capacity Ics = 100% Icu at 415 V (kA rms) 50%, frame DN1-250C type,Confirms to IS/IEC60947-2 = 02 Nos 01 (Incomer) and 01 (Spare) (ii) Phase indicating lamp LED type with HRC fuse – 1 Set of three. (iii) ON/OFF indicating lamp on incomer feeder for status of feeder = 02 Nos (iv) Digital volt meter AC 0 to 500 volts with inbuilt selector switch duly provided with suitable size of copper insulated wire with universal coloured code of size 96x96mm-01No (v) Digital Amp meter AC up to 630 Amp with inbuilt selector switch and CT’s duly prewired with suitable size of copper insulated wire with universal colour code of size 96x96mm – 01 No. (vi) Aluminium bus bar 250 Amps capacity of suitable length insulated heavy heat shrinkable sleeves etc -04 Nos.

OUTGOING: (i) MCCB 63 Amp ,415 Volt,25 KA, 4 pole, with thermal & magnetic release rated, rated Ultimate Shortcircuit Breaking Capacity Icu at 415 V (kA rms) Vac (kA rms), Rated Service short circuit Breaking Capacity Ics = 100% Icu at 415 V (kA rms) 50%, frame DN1-250C type,Confirms to IS/IEC60947-2 = 03 Nos

M&L for High mast steel tubular structure 15 metre long with Grade S-355 as per BS EN 10025 for shaft and gussets and grade FE-410 WA as per IS-2062 for 9 lantern symmetrically fitted along with their control gear and having three point suspension system with stainless steel wire rope of 6 mm dia 97/19 guage and double drum winch with luminaire mounting arm, pully assembly, LED dome aviation obstruction light with LED lamp, lightning arrester spike flange and door stiffness construction in two section longitudinal and welded in one section with thickness of sheet 3mm top and 4mm bottom and final including necessary excavation returning filling removal of soil from site all and PCC/RCC foundation of high mast light as per manufacturer design as spcified and comprising the following dimensions with the following accessories :- (a) Length of bottom section - 8.250 Mtrs (b) Length of top section -8.250 Mtrs (c) Base dia - 360 mm (approx) (d) Top dia -150 mm (approx) (e) Size of opening and door at base -1200x250 (close fitting door with suitable reinforcement to avoid Buckling at base of mast) (f)Lighting protection finial - G. single spike of length 1200 mm (g) Foundation depth - 1.5 Mtr below G.I (h) Nos of foundation bolts-08 Nos (h) PCD of foundation bolts - 460 mm (j) Diameter of foundation bolts - 30 mm (k) Length of foundation bolts - 850 mm (ii) size of base plate 520mm thick 25 mm dia complete all as specfied each set-01 Nos

(iii) Lantern Carriage:- Lantern carriage ring with class BMS pipe/tube having sleeve on carriage ring 535 mm (ID) dia suitable to mount 09 Nos of lentern fitting symetrically -01 Nos. (iv) Winch :- Winch double drum type having operating speed 180 RPM and gear ratio 53 : 1 working operating manually/electrically with stainless steel wire rope 6mm dia too point suspension system including timble copper Talurit capacity 500 Kgs (per Drum) make lubrication arrangement self lubricant in permanent oil both bath type SAE-90/140 or equivalent each Job -01 No. (v) Stainless steel wire rope:- Diameter of SS rope 6 mm, AISI 304 grade, construction of SS rope 7/19 , stainless steel of centre core material DIN 3060, 4 Nos rope of 6 mm for Lantern Carriage, 2 Nos of 6 mm for Double drum Winch, breaking load capcity of SS wire rope are 2350 Kgs per SS rope. (vi) Trailing Cable :- Copper conductor cable PVC sheathed 1100 volt grade of size 4.00 Sq mm PVC insulataed from electrical box to street light fittings separately for nine fittings each Job -01 No. (vii) Push button control 415 Volt 3 phase 50HZ 1440 RPM single speed 1100 watt torque lifting capacity 750 Kgs adjustable mechanically tripping device complete all as specified. (viii) Power Tool:_ 1 HP integral model, single speed, reversible 415 volts/240 Volts with mechanical tripping facility.

Supply,installation, testing and commisioning of factory made powder coated cubical outdoor LT feeder pillar box of size 900 x 750 x 300 mm confirming to IP-65, CPRI approved complete weather proof and vermin proof and the shell of 3.15 mm thick MS sheet with partitions and switch enclosure doors of 2 mm MS sheet with minimum clearance of 750 mm and canopy made out of 3.15 mm thick MS sheet all as per IS shall be available inside for easy access and working condition fixed on angle iron frame 50 x 50 x 6mm. Mounted on brick masonry pillars with a clearance of atleast 0.45 mtrs above GL on 100mm thick appron of PCC 1;4;8 type D-2 provided 1.0 mtr all around with a slight outward slope to avoid stagnation of water, marking to indentify incoming and outgoing circuits and earthing pillar box at two points out door feeder pillar box comprising of following :- (a) MCCB 63 Amp,4 pole 25 KA ,415 volt ICU 100% ICS with thermal based release = 02 Nos (01 Incomer, 01 spare) (b) Timer switch Analog outdoor type factory made powder coated all along internal and external surfaces, weather proof, dust and water proof with I P 55 protection, consisting of 01 No AC contactor 3 pahse 16 Amp capacity 10 KA, one digital Timer switch with 16 Amp three Nos MCB SP 10 Amp 10 KA having both auto manual and by pass system - 01 No mounted on existing panel with suitable size clamps complete all as specified and directed.

Supply and fixing High performance floodlight luminiare 200 watt with pressure die-cast housing toughened glass and secondary lens optics with IP 66 ingress protection, efficiency 120 lm/W complete with all fixing accessories all as specified and directed by Engineer-in-Charge.