Military Engineer Services Tender

Supply and fix in replacement Surge protection device suitable for LED Street light/flood light any wattage complete all as specified and directed. Note for 2 to 4 : - Electronic LED driver should be consist of all safety controll feature like SMPS based constant current supply with lower THD, Output Open / Short Circuit protection, Phase to Phase protection, Over Voltage protection,Surge Voltage protection.

Taking down unserviceable solar street light fittings of any type/wattage/make etc for repairing including checking for repair/replacement of unserviceable parts as required and making the light fittings operational to give rated illumination by replacing unserviceable spare parts and refixing the same at existing location or any other location complete all as specified and directed. Notes - (i). Cost of taking down carefully from existing position, bringing to MES store yard (If required for repair), is deemed to be included in this item quoted rates. (ii) Cost of supply and fixing of major items required to make the lights serviceable shall be measured and paid separately under item No 6.01 to 6.05 of this schedule.

Supply only following items to be incorporated against item No 5 here in before:

Battery 12 volt 15 AH.

Solar panel for generation of solar energy capacity 07 watt.

Electronic battery charger suitable for 12 volts battery.

DC to AC convertor suitable for battery 12 volts.

LED security light 15 watt IP 66, pressure die cast aluminum housing and heat resistant toughened glass with light intensity not less than 1500 lumens

Supply and fixing in replacement of high efficiency IP-65 LED Solar smart integrated light all-in-one type 40 Watt with built in premium grade mono crystalline solar pv panel 70 wp,back up for 12 hours Lithiumm base battery,11.1/12.8V,33.0 AH with inbuilt BMS single FRP body duly polyurethane coating (Camouflage color), 120 LM/W with Aluminium reflector for better light distribution ,CRI70, color temp 5700K-6500K Microcontroller based charge controller PIR sensor .The light has automatic drawn to down operation and maintenance free after installation.High efficient IP-65 LED solar lighting system with built - in high efficiency solar panel, LED light and long life lithium based battery with high efficiency micro processor based charge controller and PIR sensor. The light has automatic dusk to down operation and maintenance free after installation complete all as specified and directed. Protections: Short circuit, overload,Reserve polarity and battery protection.Firm should provide vital parametres Test report from NABL accredited lab and should be of made in India with CE & ROHS complaint.

M & L for Taking down unserviceable High Mast light poles, etc for repairing including complete dismantling, checking for repair/replacement of unserviceable parts as required including greasing etc.and making the high mast lights operational to replacing unserviceable spare parts and refixing the same at existing location or any other location as directed at site and making electrical connections with existing wire complete all as specified and directed. Notes - (i). Cost of taking down carefully from existing position after disconnecting electric connections, sealing cable ends, bringing to MES store yard (If required for repair), is deemed to be included in this item quoted. (ii) All T&P used for lowering/raising of High Mast lights/fittings etc are included in quotated rate.

Supply and fixing in replacemnt of sheet moulding compound junction box shock and rust proof, termite resistant, tamper proof , front openable type for single phase, two wire rating of size 250x200x105mm complete with one no. MCB SP 6 Amp including non metallic clamps and GI nut bolts and washers of suitable size and fixed on pole / wall complete all as specified and directed. Make - Sintex or equivalent in Hensel/ABB / Power System & Controls.

supply and fix in replacement single phase of 5KW of automatic street light switch using Infrared Sensor based NATURAL SWITCH for automatic switching of street lights. nature switch operation should be based on Natural Light Lux level, required illumiance level for switching ON is ≤ 30 Lux and for switching off ≥ 10 Lux. The sensor should have part night operation facility of min 4 hrs to max 12 hrs. The sensor along with suitable power contractor of 20 to 25 Amps current rating. incomming MCB and outgoing MCBs of 20-25 Amps and auto- manual (sensor By pass), size of circuit should be multistranded FRLS min size of 10 Sqmm, selection operation should be enclosed in a pole/wall mounted enclosure made of rust proof, electric shock proof termite proof and FR grade special mounting compound (Sintex made SMC junction box) conforming to IP 54 complete all as specified and directed.

Supply & fixing in replacemet multifunctional digital timer swith with inbuilt function for switching on / off street lights according to the rising / setting of the sun with combination function according to astronomical time and / or fixed preset times complete with all connection to existing panel twin core complete all as specified and directed.

Supply & fixing Automatic Security light control panel having sheet steel enclosure power coated CRCA sheet suitable for three phase,6 KW rating, outdoor installation,floor mounted, IP 54 protected including making all connections and grouted in PCC of type B-1 (1:2:4) with foundation should be 100mm above ground level complete with comprising of the following switch gears:- (i) MCB TPN 40Amp rating -01No (ii) Multifunctional Digital Timer Switch - 01 Nos (ii) Contactor with nominal current rating 32Amp TP (iii) Outgoing MCB SP with Suitable rating - 03 Nos (iv) Auto/manual switch (v) Incoming and outgoing terminal suitable for three phase supply.

M&L for scraping, scretching, cleaning the old paint, preparation of the surface for repainting. Painting LT 9 Mtr long PCC pole in Black & White strip 30 Cm a part alternaterly up to 1.5Mtr height from ground level with synthetic enmel paint, writing pole Nos. & applying one coat of snowcem on PCC muff & remaining portion of the pole complete all as specified and directed.

M&L for street light bracket made out of 40mm dia medium grade GI pipe of 1.2m length bent to required shape suitable for fixing street light / security light fitting on Steel tubular pole / RCC pole / building wall including two Nos clamps made out 30mm X 5mm flat with suitable nuts and bolts (clamp type - as per site requirement ) including two coats of aluminium paint over a coating of red oxide primer and Taking down of existing unserviceable rusted street light brackets with clamps, nuts and bolts etc . complete all as specified and directed.

Supply and fixing in replacement MS clamps including nuts, bolts and waashers made out of mild steel flat strip 30 x 5mm thick including cutting, bending, drilling holes in shape and size as per the pole size nd fixing with PCC/steel tubular pole for holding of GI brackets for mounting of street lights complete all as specified and directed.

M&L for dismantaling of old cracked / unserviceable PCC poles /MS pole struts any type and size complete all as specified and directed.

Supply and fixing in replacement of steel tubular swaged poles with cast iron base plate, finial taper plug, bolts, nuts & washers as per IS 2713 (Part-II) 1980 made out of mild steel tubing, type 410 SP-31 (9.0 metre long) including marking pole No on pole complete all as specified and directed. (a) Painting of poles with one coat of red oxide primer and two coat of aluminum paint (one coat before fixing and one coat of aluminum paint after fixing) over exposed surface and two coats of bituminous paint over embedded portion (b) The portion above coping shall be painted in alternative bands of black and yellow colour starting with white colour (each band of 30cm wide) by two coats of super enameled paint upto 1.5m height

Supply and fix in replacement steel tubular swan nacked pole with cast iron base plate, finial taper plug, bolts, nuts & washers made out of mild steel tubing, type 410 SP -31 (9 Mtr long) including marking pole No on pole including painting of poles with one coat of red oxide primer and two coat of aluminum paint (one coat before fixing and one coat of aluminum paint after fixing) over exposed surface and two coats of bituminous paint over embedded portion & the portion above coping shall be painted in alternative bands of black and yellow colour starting with white colour (each band of 30cm wide) by two coats of super enameled paint upto 1.5m height complete all as specified and directed. Note : Earth work and PCC in foundation shall be measured separately.

M & L for plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundation of PCC poles/struts as specified including necessary form work complete all as specified and directed.

M & L for plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundation of stay assembly etc including necessary form work , complete all as specified and directed.

M & L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for copping around poles, including necessary form work finishing even and smooth without using extra cement, complete all as specified and directed.

Supply, laying, jointing and testing of XLPE insulated, sheathed, armoured, heavy duty LT 1100 volts grade cable with aluminium conductor laid in trenches/pipes, fixed to poles/walls, fixing with suitable saddle/clamps including taking down old brunt cable of following nominal cross sectional area :-

10 sqmm 2 core.

10 sqmm 4 core.

16 sqmm 4 core

25 sqmm 4 core

35 sqmm 3.5 core

50 sqmm 3.5 core

70 sqmm 3.5 core

95 sqmm 3.5 core

Supplying and fixing in replacement 1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor, flat, served with inner sheathing of PVC tape, weather proof and overall PVC sheathed in service connections for providing electrical connections to existing security/street lights of size 1.5 Sqmm twin core complete all as specified and as directed.

All as per item No 23.00 above but size 2.5 sqmm twin core

All as per item No 23.00 above but size 4.0 sqmm twin core

All as per item No 23.00 above but size 6 sqmm twin core

All as per item No 23.00 above but size 10 sqmm twin core

Supply and fixing shackle type porcelain vitreous, white, brown or green insulators of size 75 mm height and 90 mm dia including galvanised MS straps 31x3 mm size with 12mm dia bolt, nut and washers for working pressure 1100 Volts grade complete all as specified and as directed.

M&L for loop insulator, vitreous, porcelain, white, brown or green, large size with overall dimensions 90x140mm clearance of hole 25.5 mm complete all as specified and as directed.

Cutting wild grass, bushes, creaper, unwanted vegetation from inside/surrounding of E/M installations, near transformers, pole structures etc including cutting creapers from barbed/cattle fencing of the installations as and when directed and removing of unwanted material from installation compound and depositing where complete all as specified and directed. Note : 1. The item shall be operated maximum three times in entire period of contract in the same installations. 2. Area measured separately each time.

Taking down unserviceable LED street/ security/flood light fittings of any type/wattage/make etc fitted on LT poles, High Mast light poles, building etc for repairing including complete dismantling, checking for repair/replacement of unserviceable parts as required and making the LED light fittings operational to give rated illumination by replacing unserviceable spare parts and refixing the same at existing location or any other location as directed at site and making electrical connections with existing wire complete all as specified and directed. Notes : (i) Cost of taking down carefully from existing position after disconnecting electric connections, sealing cable ends, bringing to MES store yard (If required for repair), is deemed to be included in quoted rate of this item. (ii) Cost of supply and fixing of major items required to make the lights serviceable shall be measured and paid separately under item No 02 to 04 of this schedule. (iii). Cost of items or works not mentioned under item No 02 to 04 and however required to make the lights serviceable will be provided by the contractor without any extra cost to the department and cost thereof shall deemed to be included in the rate quoted against this item. (iii) All T&P used for lowering/raising of High Mast lights/fittings etc shall be included in quoted rate.

Excavation in trenches for laying under ground cable, any type of soil not exceeding 1.5 meter wide and not exceeding 1.5 meter deep and getting out complete all as specified and directed.

Excavation in soft / loose soil in trenches not exceeding 1.5 m wide and not exceeding 3 m in depth and getting out complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing surplus excavated material to a distance not exceeding 50meter above the starting point complete all as specified and directed.

M&L for sand filling in trenches with clean dry fine sand unwashed including gently punning around cables complete all as specified and directed.

Supplying and laying reinforced precast concrete cable cover class LV type 1 with flat size 250 mm x 150 mm x 40 mm complete all as specified and directed.

Supply and fixing in replacement of LED street light fitting 30 watt 230v AC Outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and directed.

Supply and fixing in replacement of LED street light fitting 45 watt 230v AC Outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and directed.

Supply and fixing in replacement of LED street light fitting 70 watt 230v AC Outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and directed.

Supply and fixing in replacement of LED street light fitting 100 watt 230v AC Outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and directed.

Supply and fixing in replacement of LED street light fitting 120 watt 230v AC Outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and directed.

Supply and fixing in replacement of LED flood light 100 watt 230v AC Outdoor type with thermal management in multiple optics and equipped with IP-66 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed.

Supply and fixing in replacement of LED flood light 200 watt 230v AC Outdoor type with thermal management in multiple optics and equipped with IP-66 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed.

Supply and fixing in replacement of Post top lantern LED type 30W 230V AC outdoor type with decorative post top for 360 degree indirect light IP65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed.

S&F in repair LED Security light 90 watt IP 66, pressure die cast aluminum housing and heat resistant toughened glass with light intensity not less than 9000 lumens including fixing on pole or any other location with the help of existing high mast light structure including taking down existing unserviceable one complete all as specified and directed.

S&F in repair LED Security light 150 watt IP 66, pressure die cast aluminum housing and heat resistant toughened glass with light intensity not less than 9000 lumens including fixing on pole or any other location with the help of existing high mast light structure including taking down existing unserviceable one complete all as specified and directed.

S&F in repair LED flood light 150 watt IP 66, pressure die cast aluminum housing and heat resistant toughened glass with light intensity not less than 15000 lumens including fixing on pole or any other location with the help of existing high mast light structure including taking down existing unserviceable one complete all as specified and directed.

S&F LED bollard with opal diffuser and aluminum reflector capacity 09 watt including fixing/ grouting on PCC platform of suitable size and taking down existing unserviceable one complete all as specified and directed.

S&F in repair LED bollard with opal diffuser and aluminum reflector capacity 12 watt including fixing/ grouting on PCC platform of suitable size and taking down existing unserviceable one complete all as specified and directed.

S&F in repair decorative LED Post top lantern luminaires with diffuser and painted spun aluminum deflector of capacity 12 watt including fixing arrangement including taking down existing unserviceable one complete all as specified and directed.

Supply and fixing in replacement of high efficiency IP-65 LED Solar smart integrated light all-in-one type 30 Watt with built in premium grade mono crystalline solar pv panel 100 wp,back up for 24 hours Lithiumm base battery,11.1/12.8V,33.0 AH with inbuilt BMS single FRP body duly polyurethane coating (Camouflage color), 120 LM/W with Aluminium reflector for better light distribution ,CRI70, color temp 5700K-6500K Microcontroller based charge controller PIR sensor .The light has automatic drawn to down operation and maintenance free after installation.High efficient IP-65 LED solar lighting system with built - in high efficiency solar panel, LED light and long life lithium based battery with high efficiency micro processor based charge controller and PIR sensor. The light has automatic dusk to down operation and maintenance free after installation complete all as specified and directed. Protections: Short circuit, overload,Reserve polarity and battery protection.Firm should provide vital parametres Test report from NABL accredited lab and should be of made in India with CE & ROHS complaint.

S&F of Aviation obstruction light luminaries fittings having integral LED aviation light comprising of aluminium housing with polycarbonate enclosure at the top of the pole and making necessary electric connection and fixing arrangement of aviation light complete all as specified and directed.

Supply and Fixing in replacement MCB single pole 6 Amp-32 Amp for street light junction box / panel including connection complete all as specified and directed.

Supplying and fixing in replacement MCB single pole 230 volts 50 Hz AC of rating 40 to 63 Amp including connection complete all as specified and directed.

Supply & Fixing Power Contactor 63 - 80 Amp rating 4 pole including all connected accessories with suitable rating like coil / auxiliary Contact etc) as per site requirement and suitable for street light controll panel complete with all connection as complete all as specified and directed.

Supply & Fixing Power Contactor 25 to 40 Amp rating single pole including all connected accessories with suitable rating like coil / auxiliary Contact etc) as per site requirement and suitable for street light controll panel complete with all connection complete all as specified and directed.

S&F in repair MCCB 400Amp rating, 4 pole 415V, adjustable thermal adjustable megnetic type breaking capacity 36 KA complete all as specified and directed.

S&F in repair MCCB 250Amp rating, 4 pole 415V, adjustable thermal adjustable megnetic type breaking capacity 36KA complete all as specified and directed.

S&F in repair MCCB 100Amp rating, 4 pole 415V, adjustable thermal adjustable megnetic type adjustable thermal adjustable megnetic type breaking capacity 16KA complete all as specified and directed.

S&F in repair MCCB 63Amp rating,4 pole 415V, adjustable thermal adjustable megnetic type breaking capacity 16KA complete all as specified and directed.

Supply and erecting and fixing in true vertical position,hot dip galvanised inside and outside octagonal pole of 6 meter height with bottom outer dia not less than 130 mm and top outer dia not less than 70 mm and steel thickness 3 mm complete with base plate (200 X200X12 mm) mounting accessories with 04 Nos of M20X600 mm long 'J' type EN 8 grade foundation bolt alongwith templates (Steel plate for installing bolt accurately),PCD-200 mm,GI cap on top with 500 mm long hot dip galvanised single arm stadard bracket made up of 40 NB dia GI pipe as per requirement including clamp & nut &bolts and suitable arrangement to mount solar light as directed on pole having to 70 mm A/F and including foundation and errection as per manufacturer drawing complete all as specified and directed.

Supply and fixing in replacement infrared based NATURE SWITCH, selectable option for duration based switching OFF as wella soveride for maintenance to be provided in switch complete all as specified and directed.

Supply and fixing in replacement power contactor 40 Amps, three phase, AC suitable for operation of timer switch enclosure complete all as specified and directed.

Labour for cutting / Pruning / trimming of tree branches in vicinity of LT over head electric line and to be made free over head line from trees branches for avoid any short circuit between conductor complete including disposal the wastage branches by dumping in low lying area complete all as specified and directed. Note : (i) Labour / Tools / Ladder / Vehicle for Cutting / Pruning / trimming of tree branches shall be provided by contractor and rate for the same are included in the quoted rate of item.

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete all as specified and directed.

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI earth Strip 32x6 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron complete earth pit of PCC-M-10 (nominal mix) using 20 mm graded stone aggregate, 50 mm thick earth pit cover of RCC M-15 (Nominal Mix) using 20mm graded stone aggregate with MS TMT reinforcement bar of 8 mm dia @ 150 mm centre to centre both ways, MS handle 10 mm dia made to shape, PGI funnel, wire mesh and 20 mm bore GI water pipe medium grade and 40 mm bore medium grade GI pipe for protection of earth strip from plate to man switch board, common salat, charcol dust including testing on completion and all as shown in electrical plate No. 3 including testing on completion and making good the disturbed surfaces of wall floors etc without claiming extra cost complete all as specified and directed.

M&L for laying GI Tubing light grade 40mm dia for cable potection galvanised, with all fitting and fixed to walls , poles or laid in floors including removing the rusted old one complete all as specified and directed.

M&L for laying GI Tubing light grade 50mm dia for cable potection galvanised, with all fitting and fixed to walls , poles or laid in floors including removing the rusted old one complete all as specified and directed.

M&L for HDPE Double Wall Corrugated pipe of size 40mm outer dia and 32mm inner dia confirming to IS:14930 Part-II including necessary pipe fittings such as couplers, end caps, bend etc. laid in trenches/ fixed to wall with suitable clamps for cable protection complete all as specified and directed.

M&L for rewinding of electric motor upto 2.5 HP capacity with super enamel copperwire of existing gauge including insulation and varnishing, including repair to gear boax after dismantling all electrical and mechanical connection from High Mast light, testing and commissioning at site complete all as specified and directed.

M&L for replacemet of high mast wire rope of existing size complete all as specified and as directed.

M&L for for stay assembly complete with mild steel stay plate 300x300x6mm thick galvanized stay rod not less than 20mm dia, 2.15 mtr long galvanized stay bow, galvanized thimble, stay clamp etc, all as shown plate No. 1 of SSR part-1 complete all as specified and directed. Note : Excavation, earthwork, cement concrete loop type insulators and stay type insulators and stay wire shall be included in the quoted rates.

Supply, installing, commissioning and testing LT feeder pillar Box outdoor, double door cubical panel board suitable for 3 phase 4 wire 415 V, 50 Hz and CPRI approved factory fabricated powder coating having thickness not less than 100 microns provided with provided with suitable gasket to make it dust / vermin proof including danger notice board, pcc 1:2:4 type B-1 as on foundation, incoming (I/C) and outgoing (O/G) cable connection and general construction confirming to IS-8623/93 comprising of the following : Outer shell : The outer shell completely vermin proof the bottom of the outer shell contains a detachble plate having provision for entry of armoured cable of adequated size wit gland provision of threaded earthing stud at bottom & lifting lugs of suitable size at top to lift the panel safety shall be made the degree of protection of oute shell shall be IP-54 INNER SHELL : Inner Shell shall be made out of 2.00 mm thick CRCA sheet duly compartmentalized for each control gear the inner shell completly vermin proof & to accomodate incommer / outgoing MCCB and TPN aluminium bus bar of rating not less than 1.5 times the ratte capacity of the incomer MCCB. The TPN bus bar shall be insulated with colour coded heat shrinkable sleeve all controll wire shall be with 1.5 sqmm multistranded copper conductor and shall be properly bunched, tied, ferruled for proper identification and crimped with adequate size of lugs. A detachable predrilled gland plae of thcikness 3.15 mm powder coated should be used at the bottom, the iiner shell shall be of powder coated. The degree of protection for inner shell shall be IP-42 including painting with coats synthetic enameled paint over a coat of red oxide primer and consisting of the following : with two coats synthetic enameled paint over a coat of red oxide primer and consisting of the following : (a) MCCB 100 Amp 25 KA, 4 pole, Ics=100%Icu-01 No. (in coming) (b) MCCB 63 Amp 16 KA, 3 Pole (adjustable thermal and Adjustable magnetic (O/G)- 04 Nos. (c) Digital meter with voltmeter (0-500)-o1 Each (d) Rating of CT & Ammeter as per Bus bar capacity as mentioned (O/G) 04 Nos. (e) Selector switch for Ammeter (R,Y&B)-01 Set (f) Selector switch for Voltmeter (RY,YB,BR)-01 Set (i) Indicating lamps (R,Y,B)-01 Set Note : Drawing of panel shall be got approved frm GE before procurement.

Supply, installation testing timer panel of security light having sheet steel enclosure powder coated CRCA sheet, CPRI approved, outer shell shall be made out 3.15 mm & inner shell be made out 2.0 mm thick suitable for three phase, 6 KW rating, outdoor installation, cubical type for three phase, 6 KW rating, outdoor installation, cubical type, IP-54 protected, slop 1:2 danger notice plate including making all connections and grouted in PCC 1:2:4 type B-1 as in foundation of size 450X6000X6000 mm should be 100mm should be 100mm above ground level complete with 415 volts, 4 wire AC 50 Hz with aluminium busbar having provision for terminatin of incomer and outgoing cables, connectors etc complete all as specified and as directed with following accesories : (a) MCCB 4 pole 415 volts 100 Amp 25 KA (for incoming) (Adjustable thermal and Adjustable magnetic) (b) Contractor 3 pole 40 Amp (with No. and NC) - 02 (c) Timer digital type (three phase) -01 (d) Digital type voltmeter (0.500v) with selector switch-01 (e) Digital type Ammeter (0.600v A) with selector switch-01 and CTs-01 (f) Including lamp LED cluster tyoe set of three in RED/BLUE/GREEN colour - 01