Hindustan Prefab Limited Tender
If you're a registered bidder for etender UP and want to inquire about any e-tender UP government has posted, this is your stop. No need to enter every detail on the website of <a href="https://etender.up.nic.in">etender.up.nic.in</a> - BidAssist filters will help you find the exact UP etender you're looking for. Read to learn how to search & bid for etender UP.
Hindustan Prefab Limited - HPL Tender
Eprocure
Opening Date19 May 2021
Closing Date28 May 2021
Tender AmountRefer Documents
Costs
EMD
Refer DocumentsDocument Cost
₹ 5,900Tender Fee
Refer Documents
Summary
Hpl/pm(c)/tc/ctb/jdl/21-22/09
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2021_HPL_77736_1Bid Award Id
ViewTender No
HPL/PM(C)/TC/CTB/JDB/21-22/09Tender Authority
Hindustan Prefab Limited ViewPurchaser Address
-Website
http://http://hindprefab.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
Self Technical Evaluation Sheet (Technical Bid)
BOQ Items
Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50M and lift upto 1.5M
365.09
-
-
Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.
108.45
-
-
Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form wrok. 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 40 mmnominal size.
159.07
-
-
Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels,Foundations, footings, base of columns and plinth beam in any shape and size.
6179.36
-
-
'Extra for additional height every 1m or part thereof where height of staging for form work exceeds 4.0 metre with adequate bracing, propping etc at all levels, for suspended floor, roof, landing, beam and balcony. (only plan area is to be measured):
319.7
-
-
Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work. M-25 Grade
828.03
-
-
Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth
71.54
-
-
Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire in foundation and plinth all complete:
Thermo-Mechanically treated bars
85797.65
-
-
Providing and laying damp proof course (upto 50mm thick) with plain cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20mm nominal size) including formwork.
10.9
-
-
Coursed rubble masonry (Second sort) with hard stone in Cement mortar 1:6 (1 cement : 6 coarse sand) upto plinth level
35.77
-
-
Extra for brick work in superstructure above plinth level for every floor or part therof in additional to rate for foundation and plinth:
245.94
-
-
Half brick thick Brick Masonary with FLY ASH lime bricks (flag brick) confirming to ISI 12894:2002 of class designation 40 in super Strcture above plinth level Cement Mortar 1:4 (1 cement : 4 coarse sand)
72.47
-
-
Extra for providing and placing in position hopping 25x1.60 mm or 2 Nos 6mm dia MS bars reinforcement at every third course of half brick masonry.
72.47
-
-
15 mm thick Table rubbed polished Granite stone slab in risers and
treads of steps skirting dado and pillars laid on 12mm (Average) thick
base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with
grey cement slurry including rubbing and polishing etc. complete
(single stone is to be used for risers and treads of steps and width of
stone for skirting and dado shall be equal to the height of skirting &
dado and length of 1.0 m).
7.68
-
-
Providing wood work in frames of doors,Window s,clerestory windows and other frames wrought framed and fixed in position. Sal, bijasal, benteak, khair, haldu
0.45
-
-
Providing and fixing flush door shutters, conforming to IS : 2202 (Part-I), decorative type core of block board construction with frame of first class hard wood and well matched teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters excluding hinges. 40 mm. thick (single leaf) Extra for double leaf shutter instead of single leaf. if any
20.64
-
-
Providing and fixing glass panes in glazed or panelled and glazed shutters of doors and window, clerestory windows etc ( Only area of glass panes to be measured).
6 mm thick.
0.32
-
-
Providing and fixing bright finished brass tower bolts (barrel type) with brass polished MS screws complete:
200x10 mm
10
-
-
Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Engineer-in-Charge.
44.85
-
-
Providing and fixing 30mm thick factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45degree angle on either side forming styles; and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2 ) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per Manufacturer’s specification including 3 nos ISI marked stainless steel hinges of size 100x58x1.9 mm complete. (for W.C. and bathroom door shutter. PVC door shutter
22.05
-
-
Providing and fixing bright finished brass door handles with brass polished MS screws complete:
125 mm
8
-
-
Providing and fixing Anitque/S.S. finished brass door latch with necessary Antique/S.S. POlished MS screws complete: 300 x16x5 mm
8
-
-
Providing & fixing 150mm antique/ SS finished brass floor door stopper with rubber cushion and antique/ SS polished MS screw complete to suit the shutter thickness
10
-
-
Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of red oxide zinc chromate primer.
80.4
-
-
Providing and fixing “ NETLON Insect screens" with 25mm wide Hook and loop tape all around to wooden /Aluminium/ steel windows, ventilators and the like complete.
8.25
-
-
Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing and panelling to be paid for separately For fixed portion
168
-
-
Providing and fixing IS: 3564 marked aluminium die cast body tubular type
universal hydraulic door closer with necessary accessories and screws etc
complete.
10
-
-
Providing and fixing M.S. grill of approved pattern made of M.S. flats orsquare or round bars welded to steel frame of windows etc. includingapplying a priming coat welded to frame with all necessary fitting completeincluding applying a priming of red oxide zinc chromate primer. 45 KG/SQM =168.75 X45= kg
4218.75
-
-
For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately).
168
-
-
Extra for polyester powder coated (minimum 50 micron) aluminium
sections instead of anodized.
336
-
-
Providing and fixing frosted glass panes with steel glazing clips and special metal sash putty of approved make in steel doors, windows, ventilators: 5 mm thick
21
-
-
Supply and fixing of precoated TILE PATTERN profile sheets of approved make, colour, over all size, corrugation shape and pitch, having total coated thickness (TCT) 0.45 mm (approx weight 4.9 kg/sqm) with Zn-Al coating and superior paint and having yeild strength of 550 MPa. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required
72.16
-
-
Providing and fixing Terracota tiles of approved design and size over and including 20mm thick cement plaster 1:3 including floating coat of cement slurry on bed and filling joints with neat cement slurry mixed with pigment to match the shade of tiles complete.
103.95
-
-
Providing and making 6mm thick cement plaster of mix: Slab area
24.67
-
-
Providing and making 12mm thick cement plaster of mix: in cement mortar 1:6(1 cement : 6 fine sand)
95.28
-
-
Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix In Cement Mortar 1:6 (1 cement : 6 fine sand)
2661.1
-
-
Providing and fixing chicken mesh weighting not less than 250 gms/ sqm as per IS : specification in the required width with 40mm long steel nails on vertical and horizontal surface near R.C.C. and brick walls junctions including scaffolding and all lead and lifts etc. complete before plastering upto 10mts in height.
47.6
-
-
Providing and fixing 15mm thick Granite (machine cut, table rubbed & mirror polished on both sides) for partition curtain in toilets or similar locations of required size in wall with cement mortar 1:4 (1 cement : 4 coarse sand) including cutting chase in wall and joint with wall treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish
11.59
-
-
Wall painting with acrylic premium emulsion (plastic) paint of required
shade to give an even shade.
On new work (Two or more coats
2296.02
-
-
Wall painting with acrylic luxury emulsion (plastic) paint of Required Shade to give an even shade. On new work( two or more coats)
88.25
-
-
Applying one coat of cement primer on wall surface (applied @ 0.80litrs/10 sqm) complete.
116.99
-
-
Providing and applying 2mm thick ready mix exterior grade putty (Birla wall care, Alltek Superfine W/R of (NCL), J.K. wall putty) on walls to make the surface smooth and even.
243.55
-
-
Painting exterior surface with ACRYLIC SMMOTH exterior paints of required shades as per manufacture specification to give protective and decorative finish including cleaning washing of surface etc. complete with.
on new work (two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
144.96
-
-
Applying priming coat on wood work with ready mixed primer.
3.23
-
-
Providing and laying vitrified floor tiles with double charge/ multi charge printing with water absorption less than 0.5% and conforming to IS : 15622 of approved make in all colours and shades and size mentioned below (+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size above 600x600mm
292.79
-
-
Precast Terrazzo tiles 22mm thick with graded white or black or white and black marble chips of size upto 6mm laid in floors, tread of steps and landing on 25mm thick bed of cement mortar 1:6 (1 cement : 6 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and polishing complete with precast tiles of: Medium shade using approximately. 50% white cement and 50% ordinary cement
103.95
-
-
Providing & laying 60mm thick precast interlocking concrete blocks of approved size (approx 305 sqcm) and shape/ pattern, over 40 mm thick average complete coarse sand bed with joints of 3mm thick filled by fine sand including leveling with surface vibrator, temping and sweeping etc. complete of minimum compressive strength of 250 kg/sq.cm Pigment Coloured (rubber mould) precast interlock concrete blocks
3651
-
-
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20
730.17
-
-
Steel work in tubular (round, square or rectangular hollow tubes etc.)structure in built-up sections, trusses and frame work including cutting, hoisting, fixing in position upto a height of 5m above plinth level, consisting of columns trusses, roof and bottom purlins, base plate, holding down bolts, wind ties bracing (if required), bolts, nuts and washers for fastening etc. complete with applying a priming coat of red oxide zinc chromate primer. Electric resistance or induction butt welded tubes Grade-300
17056.19
-
-
Painting on new work ( two or more coats ) to give an even shade with premium synthetic enamel panits.
474.42
-
-
Extra for hoisting trusses and placing in position over height above 5m for every 2.5 m height or part thereof.
13815.51
-
-
Providing and Fixing M.S Round holding down bolts with nuts,washer and plate in cement Concrete complete
3363.2
-
-
Supply and fixing of precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transport13ation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
470
-
-
Trenching in ordinary soil upto a depth of 60cm including removal and stacking of serviceable materials and then disposing of by spreading and
neatly leveling with in a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
1278
-
-
Supplying and stacking of good earth at site including royalty, loading, unloading and carriage upto 5 km (earth measured in stacks will be reduced by 20% for payment).
18.89
-
-
Supplying and stacking sludge at site including royalty, loading, unloading and carriage upto 5 km (sludge measured in stacks will be reduced by
8% for payment).
280
-
-
Supplying and stacking at site well decayed cow dung manure from approved source, including loading, unloading and carriage upto 5 km (manure measured in stacks will be reduced by 8% for payment).
292.59
-
-
Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.
1278
-
-
Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/ and good earth to be paid separately).
159.29
-
-
Grassing with ‘Doob’ grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing including supplying good earth if needed (the goodearth shall be paid for separately). In rows 7.5 cm apart in either direction.
1278
-
-
Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm, refilling the
excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% :
one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine
dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50m lift upto 1.5 m complete (cost of sludge,
manure or extra earth to be paid for separately).
255.6
-
-
Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of
stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including
removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 1.2 m dia and 1.2 m deep. each
48
-
-
Providing and fixing M.S. flat iron tree guard 60cm dia. and 2m height above ground level formed of 4 nos. 25x6mm and 8 nos. 25x3mm vertical M.S. flats riveted to 3 nos. 25x6mm M.S. flat iron rings in two halves,bolted together with 8mm dia. and 30mm long bolts including painting two coats with paint of approved brand and manufacture over a coat of
priming, complete in all respects.
48
-
-
Edging with modular well burnt clay bricks of crushing strength not less than 25kg/ sqcm laid dry length wise including excavation, refilling,
consolidating with hand packing and spreading neatly surplus earth withina lead of 50 m :
1324.8
-
-
Hedges like Alife, Dorenta, Tikoma etc
766
-
-
Furn like Arica, China etc (3 year old)
419
-
-
Carpet Grass
125.44
-
-
Providing and fixing water closet squatting pan (Indian type W.C. pan ), 100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (same colour) conforming to IS : 7231, with flush bend and other fittings and fixtures complete including cutting and making good the walls and floors wherever required White Long pattern W.C. pan of size 580 mm
9
-
-
Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White pedestal type
1
-
-
Providing and fixing white vitreous china urinal basin with waste fitting as per IS : 2556, and other couplings in C.P. brass complete: Flat back type urinal of size 460x380x250mm
2
-
-
Providing and fixing one piece construction white vitreous china squatting plate urinal with an integral rim longitudinal flushing pipe, standard size G.I. flush pipe for back and front flush, C.P. brass coupling complete including cutting and making good the walls and floors etc. wherever required :
1
-
-
Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required : White Oval or round size 550x400mm
20
-
-
Providing and fixing vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. White
1
-
-
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink without drain board as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : 560x410 mm bowl depth 215 mm.
2
-
-
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 5mm thick mirror
13.5
-
-
Providing and fixing 600x120x5mm glass shelf with edges rounded off supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
20
-
-
Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete. 110 mm dia pipe
300
-
-
Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.
18.77.1-Tee/ Tee with door/ Bend 90° ,18.77.2-110mm each and single tee with door-110mmx110mm equal nos
90
-
-
Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.
vent covel -110
20
-
-
Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.
Access door cap -110
15
-
-
Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.
"P" trap 110mmx110mm long
10
-
-
Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.
Multi floor trap 110
15
-
-
Providing and fixing UV stabilized Unplasticised -PVC pipe clips of approved design to Rigid PVC pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm dia
420
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 20 mm nominal outer dia .Pipes.
150
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 25 mm nominal outer dia .Pipes.
180
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 20 mm nominal outer dia pipes
250
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 25 mm nominal outer dia pipes
200
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 40 mm nominal outer dia pipes
200
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 50 mm nominal outer dia pipes
200
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Long body bib cock (500 grams)
8
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
Two way bib cock (800 grams)
5
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
Stop cock (concealed) (600 grams)
20
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Bib cock (400 grams)
10
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
Angle valve for basin mixer and geyser points (450 grams)
2
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
Bottle trap set with extension pipes
20
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
Piller Cock (400 grams)
20
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
Health foscet (hand jet) with flexible connection pipe (for WC)
10
-
-
Providing and fixing stainless steel drain jali of approved make/quality.
20
-
-
Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank ; 5000 liter x2= 10000 litre
10000
-
-
Cutting holes more than 20x20 cm and upto 30x30 cm in walls including making good the same :
30
-
-
Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof.
15
-
-
Constructing masonry Chamber 60x60x75 cm, inside with modular well burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :
8
-
-
Constructing brick masonry manhole with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 ( 1 cement : 4 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation in cement concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design :
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
4
-
-
Extra for depth for manholes : Size 120x90 cm
4
-
-
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design
2
-
-
Providing and constructing brick masonry chamber for underground pipe and and bends with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets
7
-
-
Providing and constructing brick work for extra depth beyond 45 cm of brick masonry chamber with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) with inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls: For 500x700 mm size
5
-
-
Providing and constructing soak pit 1.20x1.20x1.20m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.
1
-
-
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete 150mm thick as per standard design: for 150 mm pipe
300
-
-
Carrying out the resistivity survey by VES method using Schlumberger configuration for locating the proper spot for drilling of tube well within the selected habitation, including photography, interpretation of resistivity data and submission of report in the desired format along with resistivity readings, necessary graph and photographs. (only successful point is payable) : 1 pont
1
-
-
Boring/drilling bore well perfectly vertical for the specified depth suitable to receive required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer–in-charge beyond 90 metre & upto 150 metre depth below ground level.: 150 mm dia
150
-
-
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of: 150 mm dia
2
-
-
Supplying, assembling, lowering and fixing in vertical position in bore well, ISI marked G.I. casing pipe (Plain) medium class in 4 to 7 meters length one end fitted with socket as per IS: 1239 (Part-1&Part-2) 1992 with IVth revision (Up-to-date amendments), of reputed & approved make, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer- in-charge. 150 mm nomial dia
50
-
-
Providing and fixing 80-100 mm dia PVC ball valve for inlet/ outlet of rain water harvesting pipe and filter.
2
-
-
Providing and fixing filter of minimum 100 litre capacity for roof top rain water harvesting through tube well consisting of two layered HDPE tank with five layers (each layers of minimum 100 mm) consist of coarse sand, 4mm, 6mm, 8mm & 12 mm gravels with stainless steel wire mesh fixed between each layer with suitable length and sufficient numbers of 110 mm dia PVC pipe pieces in the bottom of tank to support the above layer including fixing of inlet and out let P.V.C. pipe of required diameter upto 2 metre length on each side, Cement Concrete plateform of required size complete as directed by Engineer in charge. (excluding cost of tubewell and inlet and outlet pipe beyond 2 metre): Pit
2000
-
-
Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of following applications including surface preparation: i) 1st layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. ii) 2nd layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. iii) 3rdlayer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with coarse sand @ 1.289 kg/sqm and water proofing cement compound @ 0.07 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. iv) 4th and final layer of brick tiling with cement mortar (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured. for tank slab surface
9.18
-
-
ELECTRICAL WORKS
-
-
-
WIRING IN CONCEALED PVC conduit
Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in surface FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)
Short Point
82
-
-
WIRING IN CONCEALED PVC conduit
Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in surface FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5
)Medium Point
34
-
-
WIRING IN CONCEALED PVC conduit
Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in surface FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5
)Long Point
29
-
-
Extra for providing and fixing light plug point on board in surface FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) point wiring with modular type 3 pin 5/6 amp socket outlet and 5/6 amp switch including cost of base and cover plate and G. I. box etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)
5
-
-
Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)
3 X 2.5 sq. mm in 20mm conduit
538
-
-
Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)
3 X 4 sq. mm in 25mm conduit
60
-
-
Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.
5/6 amps one way switch
8
-
-
Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.
15/16 amps switch
5
-
-
Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.
3 pin 5/6 amp socket outlet
7
-
-
Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.
6 pin 15/16 amp socket outlet
5
-
-
Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.
Fan regulator Electronic, step type moving all round
8
-
-
Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as per specification
100mmX75mm (3 Module)
2
-
-
Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as per specification
200mmX75mm (6 Module)
5
-
-
Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in surface complete as per specification and IS: 9537 (2000 Part 5) 25 mm
375
-
-
Supplying and fixing on surface/ recess vertical type following way, 415 volts, TPN MCB distribution board of sheet steel phosphatized and powder painted, with 200 amps tinned copper busbar, common neutral link, earth bar, din bar, detachable gland/ knock out plate, including interconnections, earthing etc. as per specification. (But without MCB/RCCB/Isolator) (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door
1
-
-
Supplying and fixing SP MCB, 240 volts, 'C' curve, suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 6 amps to 32 amps
66
-
-
Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 40 amps
1
-
-
Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 18/20 watt {4 feet}
6
-
-
Supplying of following LED lamps with inbuilt electronic driver heat sink for conventional holder 9 Watt
16
-
-
Supplying, installation, testing and commissioning of following sizes ceiling fan including wiring the down rods of standard length up to 30 cm with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, earthing etc. complete as required. P.F. should be greater than 0.9, with BEE Star rating from 3 star and above, IS: 374:2019 including all amendments. 1200 mm sweep
4
-
-
Supplying and fixing following sizes of down rod of 15/20mm dia M.S. pipe of thickness 2 mm to ceiling fan including painting with matching colour etc. as per specification. 300 cm long
1
-
-
Hanging with 2 Nos ball and socket arrangement with 30cm long 1.6mm thick 20mm dia steel conduit down rod wiring in down rod with 3x1.5 sqmm FRLS PVC insulated copper conductor wire.
17
-
-
Supplying, installation, testing and commissioning of following sizes heavy duty (continuous running) 1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9 300 mm sweep
4
-
-
Supplying , installation , testing and commissioning for the following LED White /Warm White / Linear wall washer luminaire for façade lighting with aluminium extruded housing of following wattage . . The beam angle of the fitting shall be narrow , medium , wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any seperate power supply from 100 to 270 V AC , 50 Hz , power factor 0.9 and shall be IP 65 and IK 06 rated . Lifetime should be at atleast L70:50000 burning hours at 50 Degree C . Luminaire shall be conforming to BIS and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables , water proof connectors etc as required.20-25 watt
14
-
-
Supplying , installation , testing and commissioning for the following LED White /Warm White / Linear wall washer luminaire for façade lighting with aluminium extruded housing of following wattage . . The beam angle of the fitting shall be narrow , medium , wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any seperate power supply from 100 to 270 V AC , 50 Hz , power factor 0.9 and shall be IP 65 and IK 06 rated . Lifetime should be at atleast L70:50000 burning hours at 50 Degree C . Luminaire shall be conforming to BIS and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables , water proof connectors etc as required35-40 watt
12
-
-
Supplying of following 230/250 volts LED Flood light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Seperate housing for driver etc complete as per specification and P.A. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.
30 watt
6
-
-
Supplying of following 230/250 volts LED Flood light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Seperate housing for driver etc complete as per specification and P.A. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.
50 watt
6
-
-
Supplying of following 230/250 volts LED Flood light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Seperate housing for driver etc complete as per specification and P.A. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.
200 watt
3
-
-
Supplying , installation , testing and commissioning of following type Recessed LED inground/pathway Lighting fixture with IP67 protected Die-Cast Aluminum housing and High purity Lenses for superior performance. LED shall having LM80 complied as per L70 standard LEDs minimum tested for 10,000 burning hours with 3000K CCT with minimum life cycle 50000 hrs burning hours at 50˚C. Luminaire light should have secondary lenses. Driver shall be 3 stage Constant Current Constant Voltage with voltage range of 150-270V AC. Output voltage of driver should be complied to Safety Extra Low Voltage norms not exceeding 60V DC. Driver Power factor shall be 0.95 and above and THD shall be less than 10%. 6 Watt
12
-
-
Supplying, installation, testing and commissioning of LED Neon Flex Strip 220 V AC White /Warm White /Red /Blue /Pink / Yellow Coloured complete as per specification and IP65, P.F. should be greater than 0.75
250
-
-
Supplying, installation, testing and commissioning of following LED Spike Light fitting complete with Electronic Driver Heat sink Capacitor and all other accessories, including connection, earthing etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. IP-65 9 watt
14
-
-
Supply and fixing following street light pole bracket on existing pole made out of 50 mm dia MS "B" class pipe welded to 300 mm long MS pole canopy of suitable dia at a angle of 102.50 including having MS triangular stiffner of size 150 X 50 X 5 mm thick, making arrangement for tightening the bracket with pole by providing suitable size heavy duty nuts and bolts in canopy, painting with one coat of approved steel primer etc. as per specification. Double Over Hang 1.50 metre Long
14
-
-
Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Separate housing for driver etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.
60 watt
14
-
-
Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Separate housing for driver etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.
90 watt
8
-
-
Supply Erection of the decorative cast iron pole having provision of fixing decorative combo (Cast iron+M.S.) bracket as shown in the enclosed drawing/picture. The combo bracket shall be fixed on the top of the pole.Base should have on the middle an opening rectangular window of size 165x120mm for suitable for one MCB & terminal plate. Cast Iron Lamp Post Code No.-DLP-2-40-301 (Dwarka-India make) and The details of the various portions are given in the drawing; the Bracket shall be of decorative combo brackets. Further holding point of light of the Bracket shall be customized as per the light fitting Aluminum Casted decorative hanging type light fittings of total height nearly 47cm having suitable Adopter/connector for fixing on required post; as shown in the enclosed drawing/picture. The light fitting shall generally look like those shown in this drawing exactly like this. The fixture (100 Watt) having provision to fix complete with required power supply; IP-66 certified. LIGHT FITTINGS DOUBLE ARM(DGL-103-S) Ref drawing no-HPL/RVGP/JAGDALPUR/01
18
-
-
Supply & Erection of the decorative leaf shape pole having provision of fixing decorative combo (Cast iron+M.S.) bracket as shown in the enclosed drawing/picture. The combo bracket shall be fixed on the top of the pole.Base should have on the middle an opening rectangular window of size 165x120mm for suitable for one MCB & terminal plate. Cast Iron Lamp Post Code No.-DLP-2-40-301 (Dwarka-India make) and The details of the various portions are given in the drawing; the Bracket shall be of decorative combo brackets. Further holding point of light of the Bracket shall be customized as per the light fitting Aluminum Casted decorative hanging type light fittings of total height nearly 47cm having suitable Adopter/connector for fixing on required post; as shown in the enclosed drawing/picture. The light fitting shall generally look like those shown in this drawing exactly like this. The fixture (100 Watt) having provision to fix complete with required power supply; IP-66 certified. LIGHT FITTINGS SINGLE ARM (DGL-104-S) Ref drawing no-HPL/RVGP/JAGDALPUR/02
8
-
-
Supplying erection testing and commissioning of hot dipped galvanised (single dip 86 micron) 20 metre High mast pole on existing RCC foundation with all accessories and equipments, detailed as below to withstand wind pressure upto 180km/hr and minimum following specifications: a) HM shaft made of not more than 2 sections of suitable lengths with telescopic stressfit joints between sections without any circumpherencial welding, sheet thickness 4mm top and bottom sections, nominal dia 460mm on bottom and 150 mm on top, base plate 30mm thick 670mm dia, PCD of foundation bolts 650mm. b) Double drum winch for lowering & raising of lantern carriage on high mast with operatable with power tool/ manual handle attachment with a torque limiting device for safe locking of carriage. c) Raising/lowering type lantern carriage designed to carry specified nos of luminaries, control gear box, junction box. d) Top pulley assemble with weather proof cover. e) 3 Nos suitable length and size stainless steel wire ropes (minimum 6mm dia and 7/19 construction) for lowering & raising of lantern carriage. f) Suitable size and length multicore flexible copper power trailing cable (minimum 3 core 4 sqmm) g) Hinged service door in base section h) Base plate earthing terminal. i) Suitable arrangement for supply distribution with termination of suitable size underground cable in high mast. j) Lightning conductor finial made of 25mm dia 300 mm long G.I. tube having single prong. k) Anchor plate of size 750x750x6mm, tem-plates 3mm thick, GI foundation bolts 12 Nos of 30 mm dia 850 mm long (EN 8 Grade) along with nuts washers etc. (RCC fooundation and luminaries will be paid separately)
1
-
-
Designing and providing suitable and approved size RCC foundation for 12-30 mere high mast including steel reinforcement form work, embeding 2 nos 50mm dia PVC pipe for cable entry in each foundation, excavation disposal of surplus soil and curing etc. as required including laying and fixing HM foundation bolts with tam plates but excluding the cost of foundation bolts with tam plates etc complete as per specification
19.3
-
-
Providing and supllying of SITC of Architectural wall mounting / pole mounting Housing of the luminaire should be made of Synthetic, Metal with .Luminaire should be suitable for both wall mounting as well as pole mounting with Filament lamp 6 W 3000K. (Philips -1738130PN or similar)
PANEL
18
-
-
Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS powder coated sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as per specification. Upto 300 mm deep
2.46
-
-
Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminium bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as per specification. 100 amp (20x5mm)
1
-
-
Providing and fixing metal clad, TP&N 4 pole automatic change over switch unit, 415/500 volts, including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as per specification. 250 amps
1
-
-
Providing and fixing panel mounting digital type VAF (Volt-amp-frequency combined) Multi Function meter of size 100x100 (NS) in existing cubical panel including connection, testing and commissioning etc. as per specification.
1
-
-
Providing and fixing following Time switch (timer) in existing panel including connection, testing and commissioning as per specification. Astronomical type with year programmed
2
-
-
Supplying and fixing Low voltage (class -II) surge protection device (SPD) TP&N 440 volts, in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.
1
-
-
Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.
3 pole MCCB, 320A, Adjustable Thermal - Magnetic Release, 35KA
1
-
-
Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.
3 pole MCCB, 250A, Adjustable Thermal - Magnetic Release, 25KA
1
-
-
Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.
3 pole MCCB, 25-100A, Adjustable Thermal Release, 18KA
2
-
-
Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.
3 pole MCCB, 160A, Adjustable Thermal - Magnetic Release, 25KA
1
-
-
Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.
63 amps
7
-
-
Supplying and fixing DP MCB, 240 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 6 amps to 32 amps
28
-
-
Providing maintenance free earthing with following size GI pipe including making bore pit of minimum 150mm dia, providing and laying approved make Earthing Electrode of Pipe-in-Pipe technology as per IS 3043(R 2016) -1987 made of corrosion free G.I. Pipes having outer pipe of 80mm dia and inner pipe of 50mm dia and filling with specified qty highly conductive compound around pipe and above that with soft soil in bore pit complete and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as per specification: With 3 metre long GI Pipes and 50 kg back filling compound.
13
-
-
Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering, excavation and refilling the trench etc. as per specification.
20
-
-
Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as per specification.
40
-
-
Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).
3.5 x 150 sq. mm.
300
-
-
Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).
3.5 x 300 sq. mm.
40
-
-
Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).
4 x 10 sq. mm.
525
-
-
Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).
4 x 16 sq. mm.
750
-
-
Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).
4 x 25 sq. mm.
315
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade in exiting PVC/ GI pipe etc as per specification and IS: 694 (2010).
2 x 1.5 sq. mm
350
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade in exiting PVC/ GI pipe etc as per specification and IS: 694 (2010)
.4 x 1.5 sq. Mm
270
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade in exiting PVC/ GI pipe etc as per specification and IS: 694 (2010)
.6 x 1.5 sq. mm
515
-
-
Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5) 32 mm
1110
-
-
Supplying and drawing following sizes of FRLS PVC insulated copper conductor, multi strand wire in the existing surface/ concealed, FRLS PVC conduit / PVC casing caping as per specification and IS: 694 (2010)
1 x 6 sq. mm
100
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade direct in ground including sand cushioning, protective covering etc as per specification and IS: 694 (2010)
.3x4 sqmm cu ar cable
111
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade direct in ground including sand cushioning, protective covering etc as per specification and IS: 694 (2010).
4x4 sqmm cu ar cable
107
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade direct in ground including sand cushioning, protective covering etc as per specification and IS: 694 (2010).
4x6 sqmm cu ar cable
163
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade direct in ground including sand cushioning, protective covering etc as per specification and IS: 694 (2010).
3x2.5 sqmm cu cable
392
-
-
Supplying and laying HDPE pipe of 4kg/Sqcm in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification.
63 mm outer dia
151
-
-
Supplying and laying HDPE pipe of 4kg/Sqcm in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification.
110 mm outer dia
30
-
-
Constructing masonry Chamber 30x30x50 cm, inside with modular well burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary
excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40mm nominal size) and inside plastering with cement ortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design :
7
-
-
Constructing masonry Chamber 60x60x75 cm, inside with modular well
burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse
sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160
mm bottom diameter and 180 mm deep (inside) with chained lid and RCC
top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1
cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size)
and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand)
12 mm thick finished with a floating coat of neat cement complete as per
standard design :
3
-
-
ABC Fire Extinguisher 2KG Nitrogen Store Pressure As per IS: 15683:2018 Body Sheet Not Less Then 2mm Thickness, CE Mark NRV Valve With ABC Powder 90% UL 299 FIRE RATING: 1A, 34B. With all accessories.
2
-
-
CO2 type Fire Extinguisher ISI marked confirming to IS:15683:2018 Capacity 4.5Kg. INITIAL CHARGE:- Carbon dioxide used in extinguishers shall comply with IS 15222. FIRE RATING:- 55B. Complete with Hose Assembly and horn , locking arrangement, operation manual, bracket with two screw and sleeve
2
-
-
Providing and planting Heighted trees such as, Gulmohar, Badam, Neem etc. of minimum height required 3.5M in the digged pits including preparation of soil, base plantation, providing and spreading different fertilizers, soil and sand:
78
-
-
Providing C.I railing/ grill made of CI. flats, hollow C.I pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and bolts etc complete. Ref drawing no-HPL/RVGP/JAGDALPUR/03
932.63
-
-
40-50mm thick Local Bilha/ Red Flag stone slab in riser of steps, skirting, dado and pillars laid on 12mm (Average) thick cement mortar 1:4 (1 cement : 4 coarse sand) and joint with grey cement slurry mixed with pigments to match the shade of the slab i/c grinding, rubbing and polishing, procured from Bilha querry Chhattisgarh, including chisling, shaping over 50mm cement-sand mortar with recess pointing with matching colour etc.
3363.49
-
-
Supplying and fixing of FRP strips bench,PF 908 capacity-3 Adults, area 1.5MX0.61M, height 0.45M, Length 1.5M, Width 0.61M, Colour according to consultant requirement and departmental approval .Ref drawing no-HPL/RVGP/JAGDALPUR/04
15
-
-
Providing and Fixing of the information Pole made of Cast Iron Of height 3.2m fixed with a base plate of 8mm. Pole is made out of MS. Hollow circular pipe with a decorative moulds as per drawing mentioned with a bottom dia 300mm and top dia is 150 painted black with 2 coats of redoxide paint having Two name boards back to back horizantally placed and fined facing with Radium letters ( IN HINDI AND ENGLISH) make 3M with fine art. Ref drawing no-HPL/RVGP/JAGDALPUR/06
4
-
-
Providing and fixing of the cantilever road signage pole made of cast iron of height 8.5 m fixed with a base plate of 8 mm over a RCC pedestal ,pole is made out of ms hollow circular pipe with a decorative moulde as per drawing mentioned with a dia 600 mm with 2 coat of redoxide paint having one name board at top cenatileaver with decorative cast iron jali with logo and CNC cit cast iron map wirh radium film over it vertically welded to the pole and fined facing with radium lettr ( In Hindi and English) Ref drawing no-HPL/RVGP/JAGDALPUR/07
4
-
-
Providing and fixing of the welcome gate for 4 lane road made of cast iron of height 10.15 m fixed with a base plate of 8 mm over a RCC pedestal ,pole is made out of ms hollow circular pipe with a decorative moulde as per drawing mentioned with a dia 600 mm with 2 coat of redoxide paint having one name board at top cenatileaver with decorative cast iron jali with logo and CNC cit cast iron map wirh radium film over it vertically welded to the pole and fined facing with radium lettr ( In Hindi and English) Ref drawing no-HPL/RVGP/JAGDALPUR/08
4
-
-
Stone work with SAND STONE exposed face fine dressing for making RAM BHAGWAN STATUE ,upto15 metre height including base platform upto 3 metre from G.L, backing filling with a grouting of 12 mm thik mortar 1:3 ( 1 cement :3 course sand) and approved stainless steel clam/pin etc shall be used to hold stone with necessory drilling. For joint fillied with a EPOXY basd adhesive pigment matching the stone shad as per approved drawing & Specification and under the overall direction of the Eingineer-in-charge. (The rate includes the neessary centring & shuttering ,transportation, installation and all required fixing arrangement).Ref drawing no-HPL/RVGP/JAGDALPUR/09 photo no -01
80
-
-
Providing and installation of 180GSM Fabric Tensile tent with a MS POLE and Tensile cable as per drawing and design Ref drwaing no-HPL/RVGP/JAGDALPUR/12
5
-
-
Providing and placing concrete jali for ventilation purpose
10.68
-
-
Designing,Providing,installing and fixing factory finish GRC (Glass Fiber Reinforced Conctrete) cladding over entrance gate as Ref drawing no-02 HPL/RVGP/Jagdalpur/11.The minimum thickness of GRC panel 50mm thick @4.5Kg/sqft & approved texture and Colour. The framing of GRC Panel on primary structure by dry cladding method with S.S Screw, MS Angle,Plug and dowel pin proper allignment as per structural design at required location as per approved drawing & Specification and under the overall direction of the Eingineer-in-charge. (The rate includes the detailed design,fabrication of section,transportation, installation and all required fixing arrangement).
1
-
-
Designing,Providing,installing and fixing factory finish GRC (Glass Fiber Reinforced Conctrete) cladding over Kiosk ref drawing no 03.HPL/RVGP/Jagdalpur/11. The minimum thickness of GRC panel 50mm thick @4.5Kg/sqft & approved texture and Colour. The framing of GRC Panel on primary structure by dry cladding method with S.S Screw, MS Angle,Plug and dowel pin proper allignment as per structural design at required location as per approved drawing & Specification and under the overall direction of the Eingineer-in-charge. (The rate includes the detailed design,fabrication of section,transportation, installation and all required fixing arrangement).
1
-
-
CIVIL WORKS BOQ-2 for Jagdalpur (Dalpath Sagar)
-
-
-
Surface dressing of the ground including removing vegetation and making up undulations and in-equalities not exceeding 15 cms in depth/ height including disposal of rubbish upto 1.5 m lift and lead upto 50m (at least 5m away from the dressed area).
5637
-
-
Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.In all Type of Soil.
1845.28
-
-
Extra for every additional lift of 1.5 m or part there of All types of soil
138.92
-
-
Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50M and lift upto 1.5M
365.09
-
-
Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.
399.16
-
-
Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form wrok. 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 40 mmnominal size.
66.82
-
-
Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels,Foundations, footings, base of columns and plinth beam in any shape and size.
982.08
-
-
Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work. M-25 Grade
300.6
-
-
Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth
22.95
-
-
Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire in foundation and plinth all complete:
Thermo-Mechanically treated bars
33092.46
-
-
Providing and laying damp proof course (upto 50mm thick) with plain cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20mm nominal size) including formwork.
0.45
-
-
Applying a coat of hot bitumen VG-10 using @ 1.7kg/ sqm on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.
8.99
-
-
Brick work with modular FLY ASH lime bricks (flag brick) confirming to ISI 12894:2002 of class designation 40 in foundation and plinth in:Cement Mortar 1:6 (1 Cement : 6 Coarse Sand)
20.05
-
-
Extra for brick work in superstructure above plinth level for every floor or part therof in additional to rate for foundation and plinth:
23.41
-
-
Half brick thick Brick Masonary with FLY ASH lime bricks (flag brick) confirming to ISI 12894:2002 of class designation 40 in super Strcture above plinth level Cement Mortar 1:4 (1 cement : 4 coarse sand)
40.26
-
-
Extra for providing and placing in position hopping 25x1.60 mm or 2 Nos 6mm dia MS bars reinforcement at every third course of half brick masonry.
40.26
-
-
15 mm thick Table rubbed polished Granite stone slab in risers and
treads of steps skirting dado and pillars laid on 12mm (Average) thick
base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with
grey cement slurry including rubbing and polishing etc. complete
(single stone is to be used for risers and treads of steps and width of
stone for skirting and dado shall be equal to the height of skirting &
dado and length of 1.0 m).
7.68
-
-
Providing wood work in frames of doors,Window s,clerestory windows and other frames wrought framed and fixed in position. Sal, bijasal, benteak, khair, haldu
0.51
-
-
Providing and fixing flush door shutters, conforming to IS : 2202 (Part-I), decorative type core of block board construction with frame of first class hard wood and well matched teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters excluding hinges. 40 mm. thick (single leaf) Extra for double leaf shutter instead of single leaf. if any
20.57
-
-
Providing and fixing glass panes in glazed or panelled and glazed shutters of doors and window, clerestory windows etc ( Only area of glass panes to be measured).
6 mm thick.
0.32
-
-
Providing and fixing bright finished brass tower bolts (barrel type) with brass polished MS screws complete:
200x10 mm
10
-
-
Providing and fixing bright finished brass door handles with brass polished MS screws complete:
125 mm
8
-
-
Providing and fixing Anitque/S.S. finished brass door latch with necessary Antique/S.S. POlished MS screws complete: 300 x16x5 mm
8
-
-
Providing & fixing 150mm antique/ SS finished brass floor door stopper with rubber cushion and antique/ SS polished MS screw complete to suit the shutter thickness
10
-
-
Providing and fixing “ NETLON Insect screens" with 25mm wide Hook and loop tape all around to wooden /Aluminium/ steel windows, ventilators and the like complete.
8.25
-
-
Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing and panelling to be paid for separately For fixed portion
168
-
-
Providing and fixing IS: 3564 marked aluminium die cast body tubular type
universal hydraulic door closer with necessary accessories and screws etc
complete.
10
-
-
For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately).
168
-
-
Extra for polyester powder coated (minimum 50 micron) aluminium
sections instead of anodized.
336
-
-
Providing and fixing frosted glass panes with steel glazing clips and special metal sash putty of approved make in steel doors, windows, ventilators: 5 mm thick
21
-
-
Providing and making 6mm thick cement plaster of mix: Slab area
24.67
-
-
Providing and making 12mm thick cement plaster of mix: in cement mortar 1:6(1 cement : 6 fine sand)
28.78
-
-
Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix In Cement Mortar 1:6 (1 cement : 6 fine sand)
70.46
-
-
Providing and fixing chicken mesh weighting not less than 250 gms/ sqm as per IS : specification in the required width with 40mm long steel nails on vertical and horizontal surface near R.C.C. and brick walls junctions including scaffolding and all lead and lifts etc. complete before plastering upto 10mts in height.
47.6
-
-
Wall painting with acrylic premium emulsion (plastic) paint of required
shade to give an even shade.
On new work (Two or more coats
30.04
-
-
Wall painting with acrylic luxury emulsion (plastic) paint of Required Shade to give an even shade. On new work( two or more coats)
23.41
-
-
Applying one coat of cement primer on wall surface (applied @ 0.80litrs/10 sqm) complete.
36.84
-
-
Providing and applying 2mm thick ready mix exterior grade putty (Birla wall care, Alltek Superfine W/R of (NCL), J.K. wall putty) on walls to make the surface smooth and even.
123.92
-
-
Painting exterior surface with ACRYLIC SMMOTH exterior paints of required shades as per manufacture specification to give protective and decorative finish including cleaning washing of surface etc. complete with.
on new work (two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
70.46
-
-
Applying priming coat on wood work with ready mixed primer.
3.23
-
-
Providing and laying vitrified floor tiles with double charge/ multi charge printing with water absorption less than 0.5% and conforming to IS : 15622 of approved make in all colours and shades and size mentioned below (+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size above 600x600mm
208.97
-
-
15 mm thick Table rubbed polished Granite stone slab flooring laid over 20mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing etc. complete. (Area of slab should be 0.50 sqm and above
14.02
-
-
Providing & laying 60mm thick precast interlocking concrete blocks of approved size (approx 305 sqcm) and shape/ pattern, over 40 mm thick average complete coarse sand bed with joints of 3mm thick filled by fine sand including leveling with surface vibrator, temping and sweeping etc. complete of minimum compressive strength of 250 kg/sq.cm Pigment Coloured (rubber mould) precast interlock concrete blocks
3651
-
-
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20
730.17
-
-
Steel work in tubular (round, square or rectangular hollow tubes etc.)structure in built-up sections, trusses and frame work including cutting, hoisting, fixing in position upto a height of 5m above plinth level, consisting of columns trusses, roof and bottom purlins, base plate, holding down bolts, wind ties bracing (if required), bolts, nuts and washers for fastening etc. complete with applying a priming coat of red oxide zinc chromate primer. Electric resistance or induction butt welded tubes Grade-300
17056.19
-
-
Painting on new work ( two or more coats ) to give an even shade with premium synthetic enamel panits.
470
-
-
Extra for hoisting trusses and placing in position over height above 5m for every 2.5 m height or part thereof.
13815.51
-
-
Providing and Fixing M.S Round holding down bolts with nuts,washer and plate in cement Concrete complete
613.2
-
-
Supply and fixing of precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transport13ation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
470
-
-
Dismantling rammed moorum and boulders or rammed moorum and silt in foundation or under floor including all lead and lifts.
588.11
-
-
Demolishing brick masonry including arches, stacking of serviceable material disposal of unserviceable material within 50 metres lead. In cement mortar.
1990.22
-
-
Dismantling flag stone flooring laid in cement/lime mortar including
stacking of serviceable material and disposal of unserviceable material
within 50 metre lead.
188.76
-
-
Demolishing R.C.C. work including stacking of steel bars and disposal of unserviceable material within 50 metre lead.
436.83
-
-
Demolishing cement concrete including disposal of material within 50metre lead. 1:3:6 or richer mix
405.63
-
-
Extra for cutting reinforcement bars in R.C.C. or R.B work. (Crosssectional area of RCC/RB work to be measured)
138.9
-
-
Trenching in ordinary soil upto a depth of 60cm including removal and stacking of serviceable materials and then disposing of by spreading and
neatly leveling with in a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
255.6
-
-
Supplying and stacking of good earth at site including royalty, loading, unloading and carriage upto 5 km (earth measured in stacks will be reduced by 20% for payment).
14.1
-
-
Supplying and stacking sludge at site including royalty, loading, unloading and carriage upto 5 km (sludge measured in stacks will be reduced by
8% for payment).
280
-
-
Supplying and stacking at site well decayed cow dung manure from approved source, including loading, unloading and carriage upto 5 km (manure measured in stacks will be reduced by 8% for payment).
289.4
-
-
Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.
1278
-
-
Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/ and good earth to be paid separately).
151.3
-
-
Grassing with ‘Doob’ grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing including supplying good earth if needed (the goodearth shall be paid for separately). In rows 7.5 cm apart in either direction.
1278
-
-
Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm, refilling the
excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% :
one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine
dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50m lift upto 1.5 m complete (cost of sludge,
manure or extra earth to be paid for separately).
255.6
-
-
Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of
stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including
removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 1.2 m dia and 1.2 m deep. each
48
-
-
Providing and fixing M.S. flat iron tree guard 60cm dia. and 2m height above ground level formed of 4 nos. 25x6mm and 8 nos. 25x3mm vertical M.S. flats riveted to 3 nos. 25x6mm M.S. flat iron rings in two halves,bolted together with 8mm dia. and 30mm long bolts including painting two coats with paint of approved brand and manufacture over a coat of
priming, complete in all respects.
48
-
-
Edging with modular well burnt clay bricks of crushing strength not less than 25kg/ sqcm laid dry length wise including excavation, refilling,
consolidating with hand packing and spreading neatly surplus earth withina lead of 50 m :
1295
-
-
Hedges like Alife, Dorenta, Tikoma etc
766
-
-
Furn like Arica, China etc (3 year old)
419
-
-
Carpet Grass
94
-
-
Providing and fixing water closet squatting pan (Indian type W.C. pan ), 100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (same colour) conforming to IS : 7231, with flush bend and other fittings and fixtures complete including cutting and making good the walls and floors wherever required White Long pattern W.C. pan of size 580 mm
9
-
-
Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White pedestal type
1
-
-
Providing and fixing white vitreous china urinal basin with waste fitting as per IS : 2556, and other couplings in C.P. brass complete: Flat back type urinal of size 460x380x250mm
2
-
-
Providing and fixing one piece construction white vitreous china squatting plate urinal with an integral rim longitudinal flushing pipe, standard size G.I. flush pipe for back and front flush, C.P. brass coupling complete including cutting and making good the walls and floors etc. wherever required :
1
-
-
Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required : White Oval or round size 550x400mm
20
-
-
Providing and fixing vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. White
1
-
-
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink without drain board as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : 560x410 mm bowl depth 215 mm.
2
-
-
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 5mm thick mirror
13.5
-
-
Providing and fixing 600x120x5mm glass shelf with edges rounded off supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
20
-
-
Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete. 110 mm dia pipe
300
-
-
Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.
18.77.1-Tee/ Tee with door/ Bend 90° ,18.77.2-110mm each and single tee with door-110mmx110mm equal nos
90
-
-
Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.
vent covel -110
20
-
-
Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.
Access door cap -110
15
-
-
Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.
"P" trap 110mmx110mm long
10
-
-
Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.
Multi floor trap 110
15
-
-
Providing and fixing UV stabilized Unplasticised -PVC pipe clips of approved design to Rigid PVC pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm dia
420
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 20 mm nominal outer dia .Pipes.
150
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 25 mm nominal outer dia .Pipes.
180
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 20 mm nominal outer dia pipes
250
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 25 mm nominal outer dia pipes
200
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 40 mm nominal outer dia pipes
200
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 50 mm nominal outer dia pipes
200
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Long body bib cock (500 grams)
8
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
Two way bib cock (800 grams)
5
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
Stop cock (concealed) (600 grams)
20
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Bib cock (400 grams)
10
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
Angle valve for basin mixer and geyser points (450 grams)
2
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
Bottle trap set with extension pipes
20
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
Piller Cock (400 grams)
20
-
-
Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
Health foscet (hand jet) with flexible connection pipe (for WC)
10
-
-
Providing and fixing stainless steel drain jali of approved make/quality.
20
-
-
Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank ; 5000 liter x2= 10000 litre
10000
-
-
Cutting holes more than 20x20 cm and upto 30x30 cm in walls including making good the same :
30
-
-
Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof.
15
-
-
Constructing masonry Chamber 60x60x75 cm, inside with modular well burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :
8
-
-
Constructing brick masonry manhole with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 ( 1 cement : 4 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation in cement concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design :
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
4
-
-
Extra for depth for manholes : Size 120x90 cm
4
-
-
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design
2
-
-
Providing and constructing brick masonry chamber for underground pipe and and bends with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets
7
-
-
Providing and constructing brick work for extra depth beyond 45 cm of brick masonry chamber with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) with inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls: For 500x700 mm size
5
-
-
Providing and constructing soak pit 1.20x1.20x1.20m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.
1
-
-
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete 150mm thick as per standard design: for 150 mm pipe
300
-
-
Carrying out the resistivity survey by VES method using Schlumberger configuration for locating the proper spot for drilling of tube well within the selected habitation, including photography, interpretation of resistivity data and submission of report in the desired format along with resistivity readings, necessary graph and photographs. (only successful point is payable) : 1 pont
1
-
-
Boring/drilling bore well perfectly vertical for the specified depth suitable to receive required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer–in-charge beyond 90 metre & upto 150 metre depth below ground level.: 150 mm dia
150
-
-
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of: 150 mm dia
2
-
-
Supplying, assembling, lowering and fixing in vertical position in bore well, ISI marked G.I. casing pipe (Plain) medium class in 4 to 7 meters length one end fitted with socket as per IS: 1239 (Part-1&Part-2) 1992 with IVth revision (Up-to-date amendments), of reputed & approved make, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer- in-charge. 150 mm nomial dia
50
-
-
Providing and fixing 80-100 mm dia PVC ball valve for inlet/ outlet of rain water harvesting pipe and filter.
2
-
-
Providing and fixing filter of minimum 100 litre capacity for roof top rain water harvesting through tube well consisting of two layered HDPE tank with five layers (each layers of minimum 100 mm) consist of coarse sand, 4mm, 6mm, 8mm & 12 mm gravels with stainless steel wire mesh fixed between each layer with suitable length and sufficient numbers of 110 mm dia PVC pipe pieces in the bottom of tank to support the above layer including fixing of inlet and out let P.V.C. pipe of required diameter upto 2 metre length on each side, Cement Concrete plateform of required size complete as directed by Engineer in charge. (excluding cost of tubewell and inlet and outlet pipe beyond 2 metre): Pit
2000
-
-
Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of following applications including surface preparation: i) 1st layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. ii) 2nd layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. iii) 3rdlayer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with coarse sand @ 1.289 kg/sqm and water proofing cement compound @ 0.07 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. iv) 4th and final layer of brick tiling with cement mortar (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured. for tank slab surface
9.18
-
-
ELECTRICAL WORKS
-
-
-
WIRING IN CONCEALED PVC conduit
Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in surface FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)
Short Point
82
-
-
WIRING IN CONCEALED PVC conduit
Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in surface FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5
)Medium Point
34
-
-
WIRING IN CONCEALED PVC conduit
Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in surface FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5
)Long Point
29
-
-
Extra for providing and fixing light plug point on board in surface FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) point wiring with modular type 3 pin 5/6 amp socket outlet and 5/6 amp switch including cost of base and cover plate and G. I. box etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)
5
-
-
Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)
3 X 2.5 sq. mm in 20mm conduit
538
-
-
Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)
3 X 4 sq. mm in 25mm conduit
60
-
-
Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.
5/6 amps one way switch
8
-
-
Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.
15/16 amps switch
5
-
-
Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.
3 pin 5/6 amp socket outlet
7
-
-
Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.
6 pin 15/16 amp socket outlet
5
-
-
Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.
Fan regulator Electronic, step type moving all round
8
-
-
Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as per specification
100mmX75mm (3 Module)
2
-
-
Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as per specification
200mmX75mm (6 Module)
5
-
-
Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in surface complete as per specification and IS: 9537 (2000 Part 5) 25 mm
375
-
-
Supplying and fixing on surface/ recess vertical type following way, 415 volts, TPN MCB distribution board of sheet steel phosphatized and powder painted, with 200 amps tinned copper busbar, common neutral link, earth bar, din bar, detachable gland/ knock out plate, including interconnections, earthing etc. as per specification. (But without MCB/RCCB/Isolator) (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door
1
-
-
Supplying and fixing SP MCB, 240 volts, 'C' curve, suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 6 amps to 32 amps
66
-
-
Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 40 amps
1
-
-
Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 18/20 watt {4 feet}
6
-
-
Supplying of following LED lamps with inbuilt electronic driver heat sink for conventional holder 9 Watt
16
-
-
Supplying, installation, testing and commissioning of following sizes ceiling fan including wiring the down rods of standard length up to 30 cm with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, earthing etc. complete as required. P.F. should be greater than 0.9, with BEE Star rating from 3 star and above, IS: 374:2019 including all amendments. 1200 mm sweep
4
-
-
Supplying and fixing following sizes of down rod of 15/20mm dia M.S. pipe of thickness 2 mm to ceiling fan including painting with matching colour etc. as per specification. 300 cm long
1
-
-
Hanging with 2 Nos ball and socket arrangement with 30cm long 1.6mm thick 20mm dia steel conduit down rod wiring in down rod with 3x1.5 sqmm FRLS PVC insulated copper conductor wire.
17
-
-
Supplying, installation, testing and commissioning of following sizes heavy duty (continuous running) 1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9 300 mm sweep
4
-
-
Supplying , installation , testing and commissioning for the following LED White /Warm White / Linear wall washer luminaire for façade lighting with aluminium extruded housing of following wattage . . The beam angle of the fitting shall be narrow , medium , wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any seperate power supply from 100 to 270 V AC , 50 Hz , power factor 0.9 and shall be IP 65 and IK 06 rated . Lifetime should be at atleast L70:50000 burning hours at 50 Degree C . Luminaire shall be conforming to BIS and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables , water proof connectors etc as required.20-25 watt
14
-
-
Supplying , installation , testing and commissioning for the following LED White /Warm White / Linear wall washer luminaire for façade lighting with aluminium extruded housing of following wattage . . The beam angle of the fitting shall be narrow , medium , wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any seperate power supply from 100 to 270 V AC , 50 Hz , power factor 0.9 and shall be IP 65 and IK 06 rated . Lifetime should be at atleast L70:50000 burning hours at 50 Degree C . Luminaire shall be conforming to BIS and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables , water proof connectors etc as required35-40 watt
12
-
-
Supplying of following 230/250 volts LED Flood light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Seperate housing for driver etc complete as per specification and P.A. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.
30 watt
6
-
-
Supplying of following 230/250 volts LED Flood light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Seperate housing for driver etc complete as per specification and P.A. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.
50 watt
6
-
-
Supplying of following 230/250 volts LED Flood light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Seperate housing for driver etc complete as per specification and P.A. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.
200 watt
3
-
-
Supplying , installation , testing and commissioning of following type Recessed LED inground/pathway Lighting fixture with IP67 protected Die-Cast Aluminum housing and High purity Lenses for superior performance. LED shall having LM80 complied as per L70 standard LEDs minimum tested for 10,000 burning hours with 3000K CCT with minimum life cycle 50000 hrs burning hours at 50˚C. Luminaire light should have secondary lenses. Driver shall be 3 stage Constant Current Constant Voltage with voltage range of 150-270V AC. Output voltage of driver should be complied to Safety Extra Low Voltage norms not exceeding 60V DC. Driver Power factor shall be 0.95 and above and THD shall be less than 10%. 6 Watt
12
-
-
Supplying, installation, testing and commissioning of LED Neon Flex Strip 220 V AC White /Warm White /Red /Blue /Pink / Yellow Coloured complete as per specification and IP65, P.F. should be greater than 0.75
250
-
-
Supplying, installation, testing and commissioning of following LED Spike Light fitting complete with Electronic Driver Heat sink Capacitor and all other accessories, including connection, earthing etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. IP-65 9 watt
14
-
-
Supply and fixing following street light pole bracket on existing pole made out of 50 mm dia MS "B" class pipe welded to 300 mm long MS pole canopy of suitable dia at a angle of 102.50 including having MS triangular stiffner of size 150 X 50 X 5 mm thick, making arrangement for tightening the bracket with pole by providing suitable size heavy duty nuts and bolts in canopy, painting with one coat of approved steel primer etc. as per specification. Double Over Hang 1.50 metre Long
14
-
-
Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Separate housing for driver etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.
60 watt
14
-
-
Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Separate housing for driver etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.
90 watt
8
-
-
Supply Erection of the decorative cast iron pole having provision of fixing decorative combo (Cast iron+M.S.) bracket as shown in the enclosed drawing/picture. The combo bracket shall be fixed on the top of the pole.Base should have on the middle an opening rectangular window of size 165x120mm for suitable for one MCB & terminal plate. Cast Iron Lamp Post Code No.-DLP-2-40-301 (Dwarka-India make) and The details of the various portions are given in the drawing; the Bracket shall be of decorative combo brackets. Further holding point of light of the Bracket shall be customized as per the light fitting Aluminum Casted decorative hanging type light fittings of total height nearly 47cm having suitable Adopter/connector for fixing on required post; as shown in the enclosed drawing/picture. The light fitting shall generally look like those shown in this drawing exactly like this. The fixture (100 Watt) having provision to fix complete with required power supply; IP-66 certified. LIGHT FITTINGS DOUBLE ARM(DGL-103-S) Ref drwaing no-HPL/RVGP/JAGDALPUR/01
18
-
-
Supply & Erection of the decorative leaf shape pole having provision of fixing decorative combo (Cast iron+M.S.) bracket as shown in the enclosed drawing/picture. The combo bracket shall be fixed on the top of the pole.Base should have on the middle an opening rectangular window of size 165x120mm for suitable for one MCB & terminal plate. Cast Iron Lamp Post Code No.-DLP-2-40-301 (Dwarka-India make) and The details of the various portions are given in the drawing; the Bracket shall be of decorative combo brackets. Further holding point of light of the Bracket shall be customized as per the light fitting Aluminum Casted decorative hanging type light fittings of total height nearly 47cm having suitable Adopter/connector for fixing on required post; as shown in the enclosed drawing/picture. The light fitting shall generally look like those shown in this drawing exactly like this. The fixture (100 Watt) having provision to fix complete with required power supply; IP-66 certified. LIGHT FITTINGS SINGLE ARM (DGL-104-S) Ref drwaing no-HPL/RVGP/JAGDALPUR/02
8
-
-
Supplying erection testing and commissioning of hot dipped galvanised (single dip 86 micron) 20 metre High mast pole on existing RCC foundation with all accessories and equipments, detailed as below to withstand wind pressure upto 180km/hr and minimum following specifications: a) HM shaft made of not more than 2 sections of suitable lengths with telescopic stressfit joints between sections without any circumpherencial welding, sheet thickness 4mm top and bottom sections, nominal dia 460mm on bottom and 150 mm on top, base plate 30mm thick 670mm dia, PCD of foundation bolts 650mm. b) Double drum winch for lowering & raising of lantern carriage on high mast with operatable with power tool/ manual handle attachment with a torque limiting device for safe locking of carriage. c) Raising/lowering type lantern carriage designed to carry specified nos of luminaries, control gear box, junction box. d) Top pulley assemble with weather proof cover. e) 3 Nos suitable length and size stainless steel wire ropes (minimum 6mm dia and 7/19 construction) for lowering & raising of lantern carriage. f) Suitable size and length multicore flexible copper power trailing cable (minimum 3 core 4 sqmm) g) Hinged service door in base section h) Base plate earthing terminal. i) Suitable arrangement for supply distribution with termination of suitable size underground cable in high mast. j) Lightning conductor finial made of 25mm dia 300 mm long G.I. tube having single prong. k) Anchor plate of size 750x750x6mm, tem-plates 3mm thick, GI foundation bolts 12 Nos of 30 mm dia 850 mm long (EN 8 Grade) along with nuts washers etc. (RCC fooundation and luminaries will be paid separately)
1
-
-
Designing and providing suitable and approved size RCC foundation for 12-30 mere high mast including steel reinforcement form work, embeding 2 nos 50mm dia PVC pipe for cable entry in each foundation, excavation disposal of surplus soil and curing etc. as required including laying and fixing HM foundation bolts with tam plates but excluding the cost of foundation bolts with tam plates etc complete as per specification
19.3
-
-
Providing and supllying of SITC of Architectural wall mounting / pole mounting Housing of the luminaire should be made of Synthetic, Metal with .Luminaire should be suitable for both wall mounting as well as pole mounting with Filament lamp 6 W 3000K. (Philips -1738130PN or similar)
PANEL
18
-
-
Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS powder coated sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as per specification. Upto 300 mm deep
2.46
-
-
Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminium bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as per specification. 100 amp (20x5mm)
1
-
-
Providing and fixing metal clad, TP&N 4 pole automatic change over switch unit, 415/500 volts, including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as per specification. 250 amps
1
-
-
Providing and fixing panel mounting digital type VAF (Volt-amp-frequency combined) Multi Function meter of size 100x100 (NS) in existing cubical panel including connection, testing and commissioning etc. as per specification.
1
-
-
Providing and fixing following Time switch (timer) in existing panel including connection, testing and commissioning as per specification. Astronomical type with year programmed
2
-
-
Supplying and fixing Low voltage (class -II) surge protection device (SPD) TP&N 440 volts, in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.
1
-
-
Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.
3 pole MCCB, 320A, Adjustable Thermal - Magnetic Release, 35KA
1
-
-
Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.
3 pole MCCB, 250A, Adjustable Thermal - Magnetic Release, 25KA
1
-
-
Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.
3 pole MCCB, 25-100A, Adjustable Thermal Release, 18KA
2
-
-
Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.
3 pole MCCB, 160A, Adjustable Thermal - Magnetic Release, 25KA
1
-
-
Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.
63 amps
7
-
-
Supplying and fixing DP MCB, 240 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 6 amps to 32 amps
28
-
-
Providing maintenance free earthing with following size GI pipe including making bore pit of minimum 150mm dia, providing and laying approved make Earthing Electrode of Pipe-in-Pipe technology as per IS 3043(R 2016) -1987 made of corrosion free G.I. Pipes having outer pipe of 80mm dia and inner pipe of 50mm dia and filling with specified qty highly conductive compound around pipe and above that with soft soil in bore pit complete and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as per specification: With 3 metre long GI Pipes and 50 kg back filling compound.
13
-
-
Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering, excavation and refilling the trench etc. as per specification.
20
-
-
Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as per specification.
40
-
-
Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).
3.5 x 150 sq. mm.
300
-
-
Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).
3.5 x 300 sq. mm.
40
-
-
Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).
4 x 10 sq. mm.
525
-
-
Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).
4 x 16 sq. mm.
750
-
-
Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).
4 x 25 sq. mm.
315
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade in exiting PVC/ GI pipe etc as per specification and IS: 694 (2010).
2 x 1.5 sq. mm
350
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade in exiting PVC/ GI pipe etc as per specification and IS: 694 (2010)
.4 x 1.5 sq. Mm
270
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade in exiting PVC/ GI pipe etc as per specification and IS: 694 (2010)
.6 x 1.5 sq. mm
515
-
-
Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5) 32 mm
1110
-
-
Supplying and drawing following sizes of FRLS PVC insulated copper conductor, multi strand wire in the existing surface/ concealed, FRLS PVC conduit / PVC casing caping as per specification and IS: 694 (2010)
1 x 6 sq. mm
100
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade direct in ground including sand cushioning, protective covering etc as per specification and IS: 694 (2010)
.3x4 sqmm cu ar cable
111
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade direct in ground including sand cushioning, protective covering etc as per specification and IS: 694 (2010).
4x4 sqmm cu ar cable
107
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade direct in ground including sand cushioning, protective covering etc as per specification and IS: 694 (2010).
4x6 sqmm cu ar cable
163
-
-
Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade direct in ground including sand cushioning, protective covering etc as per specification and IS: 694 (2010).
3x2.5 sqmm cu cable
392
-
-
Supplying and laying HDPE pipe of 4kg/Sqcm in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification.
63 mm outer dia
151
-
-
Supplying and laying HDPE pipe of 4kg/Sqcm in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification.
110 mm outer dia
30
-
-
Constructing masonry Chamber 30x30x50 cm, inside with modular well burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary
excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40mm nominal size) and inside plastering with cement ortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design :
7
-
-
Constructing masonry Chamber 60x60x75 cm, inside with modular well
burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse
sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160
mm bottom diameter and 180 mm deep (inside) with chained lid and RCC
top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1
cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size)
and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand)
12 mm thick finished with a floating coat of neat cement complete as per
standard design :
3
-
-
ABC Fire Extinguisher 2KG Nitrogen Store Pressure As per IS: 15683:2018 Body Sheet Not Less Then 2mm Thickness, CE Mark NRV Valve With ABC Powder 90% UL 299 FIRE RATING: 1A, 34B. With all accessories.
2
-
-
CO2 type Fire Extinguisher ISI marked confirming to IS:15683:2018 Capacity 4.5Kg. INITIAL CHARGE:- Carbon dioxide used in extinguishers shall comply with IS 15222. FIRE RATING:- 55B. Complete with Hose Assembly and horn , locking arrangement, operation manual, bracket with two screw and sleeve
2
-
-
Providing and planting Heighted trees such as, Gulmohar, Badam, Neem etc. of minimum height required 3.5M in the digged pits including preparation of soil, base plantation, providing and spreading different fertilizers, soil and sand:
78
-
-
Providing C.I railing/ grill made of CI. flats, hollow C.I pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and bolts etc complete. Ref drwaing no-HPL/RVGP/JAGDALPUR/03
855
-
-
40-50mm thick Local Bilha/ Red Flag stone slab in riser of steps, skirting, dado and pillars laid on 12mm (Average) thick cement mortar 1:4 (1 cement : 4 coarse sand) and joint with grey cement slurry mixed with pigments to match the shade of the slab i/c grinding, rubbing and polishing, procured from Bilha querry Chhattisgarh, including chisling, shaping over 50mm cement-sand mortar with recess pointing with matching colour etc.
1585.39
-
-
Supplying and fixing of FRP strips bench,PF 908 capacity-3 Adults, area 1.5MX0.61M, height 0.45M, Length 1.5M, Width 0.61M, Colour according to consultant requirement and departmental approval. Ref drwaing no-HPL/RVGP/JAGDALPUR/04
61
-
-
Providing and supply of precast concrete barricading In the Periphery of the premises as per following specification:- Material-Concrete, Height- 900 mm, length-3500MM, Width-154mm, Weight-330Kg, Shape as per Drawing, Steel-8mm, Grade-M30 Concrete, well cured, Mould-Iron/Metal, finished with a 2 coat of spray paint with 3 base of putty rubbed with sand paper.
79.22
-
-
Providing and fixing of fre-fabricated shop with a decorative elementry design as per specification of size 1500x3200x2500mm with a shop title and project logo provision and all electrical points in built as per drwaing A) Structure: - Structure of pre-fabricated shop should be structurally tainless Steel work in tubular (round, square or rectangular hollow tubes etc.). complete with applying a priming coat of red oxide zinc chromate primer Including RAM GAMAN THEME.P/F HOLLOW TUBE 100 X 100X 5, TAKING TUBE WEIGHT = 14.70Kg/m And P/F HOLLOW TUBE 50 X 50 X 5, TAKING TUBE WEIGHT = 6.90Kg/mtake in base and colum
B) Wall :- PUF PANEL dimensionhickness 50 mmUsage/Application WallPattern PlainMaterial PUFShape RectangularDensity 35-40 Kg/Sq mtrTensile Strength 3.7 kg/cm2Temperature -18 deg to +140 deg CAdhesion Strength 2.9 kg/cm2 as per Drwaing and Engineer incharge Ref drwaing no-HPL/RVGP/JAGDALPUR/05
5
-
-
Providing and Fixing of the information Pole made of Cast Iron Of height 3.2m fixed with a base plate of 8mm. Pole is made out of MS. Hollow circular pipe with a decorative moulds as per drawing mentioned with a bottom dia 300mm and top dia is 150 painted black with 2 coats of redoxide paint having Two name boards back to back horizantally placed and fined facing with Radium letters ( IN HINDI AND ENGLISH) make 3M with fine art. Ref drwaing no-HPL/RVGP/JAGDALPUR/06
8
-
-
Providing and fixing of the cantilever road signage pole made of cast iron of height 8.5 m fixed with a base plate of 8 mm over a RCC pedestal ,pole is made out of ms hollow circular pipe with a decorative moulde as per drawing mentioned with a dia 600 mm with 2 coat of redoxide paint having one name board at top cenatileaver with decorative cast iron jali with logo and CNC cit cast iron map wirh radium film over it vertically welded to the pole and fined facing with radium lettr ( In Hindi and English) Ref drwaing no-HPL/RVGP/JAGDALPUR/07
4
-
-
Providing and fixing of the welcome gate for 4 lane road made of cast iron of height 10.15 m fixed with a base plate of 8 mm over a RCC pedestal ,pole is made out of ms hollow circular pipe with a decorative moulde as per drawing mentioned with a dia 600 mm with 2 coat of redoxide paint having one name board at top cenatileaver with decorative cast iron jali with logo and CNC cit cast iron map wirh radium film over it vertically welded to the pole and fined facing with radium lettr ( In Hindi and English) Ref drwaing no-HPL/RVGP/JAGDALPUR/08
4
-
-
Providing and Fixing of the LED RAM VAN GAMAN PATH Letters of length 6M made and cut with CNC machine as per apporved drawng fonts and 8mm weather proof acrylic sheet internally fixed with a silicon and 3M adhesives and externally screwed in a MS frame with all needed accessories.
1
-
-
Stone work with SAND STONE exposed face fine dressing for making RAM BHAGWAN STATUE ,upto15 metre height including base platform upto 3 metre from G.L, backing filling with a grouting of 12 mm thik mortar 1:3 ( 1 cement :3 course sand) and approved stainless steel clam/pin etc shall be used to hold stone with necessory drilling. For joint fillied with a EPOXY basd adhesive pigment matching the stone shad as per approved drawing & Specification and under the overall direction of the Eingineer-in-charge.The statue to be placed on 10 ft high plateform .the overall hieght of the statue including plateform is to be 51 feet from the ground level . (The rate includes the neessary centring & shuttering ,transportation, installation and all required fixing arrangement). Ref drwaing no-01 HPL/RVGP/JAGDALPUR/09 and photo 01
80
-
-
Providing & fixing both dressed stone work in aslar masonary of sandstone in superstructure above plinth level and upto floor five level in cement mortat 1:4 etc complete as er direction of Engineer incharge. (Stone size 1.5 m x 0.5 m x 0.6 m) as per drwaing Ref drwaing no-HPL/RVGP/JAGDALPUR/10
52.59
-
-
Designing,Providing,installing and fixing factory finish GRC (Glass Fiber Reinforced Conctrete) cladding over entrance gate as Ref drawing no-02 HPL/RVGP/Jagdalpur/11.The minimum thickness of GRC panel 50mm thick @4.5Kg/sqft & approved texture and Colour. The framing of GRC Panel on primary structure by dry cladding method with S.S Screw, MS Angle,Plug and dowel pin proper allignment as per structural design at required location as per approved drawing & Specification and under the overall direction of the Eingineer-in-charge. (The rate includes the detailed design,fabrication of section,transportation, installation and all required fixing arrangement).
1
-
-
Designing,Providing,installing and fixing factory finish GRC (Glass Fiber Reinforced Conctrete) cladding over Kiosk ref drawing no 03. The minimum thickness of GRC panel 50mm thick @4.5Kg/sqft & approved texture and Colour. The framing of GRC Panel on primary structure by dry cladding method with S.S Screw, MS Angle,Plug and dowel pin proper allignment as per structural design at required location as per approved drawing & Specification and under the overall direction of the Eingineer-in-charge. (The rate includes the detailed design,fabrication of section,transportation, installation and all required fixing arrangement).
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements