Animal Resources Development Department Tender

Laminar flow-- • Cabinet made from mild steel • Pre-Filter Assemblage for Multi-Dispose particle predominantly in the size range of 5- 20 microns • HEPA Filter - 0.3 microns • Sealed white light • UV- light • Stainless Steel Work table • Front Door • Gas cock • Anti Vibration Leveling leg / Castor wheels • Extra power outlet switch • Size : 4' x 2' x 2' TECHNICAL FEATURES: • AIR FLOW: Designed for 0.45m/s to 0.65 m/s • PRE-FILTERS: Size : 800 x 400x 50 • Type : Flange type • Media : Synthetic, Non-oven Polyester fibre, Washable type • Casing : M.S.Powder coated • Gasket : Neoprene • Retention : 5 Micron • Efficiency : 95% • Pressure drop : 6 to 8 mm HEPA FILTER : • Size : 1200 x 610 x 75 mm - 1 no (4 feet unit) • Type : Box type, seperator type • Media : Ultra clean glass fibre paper- imported • Casing : M.S.Powder coated • Gasket : Neoprene • Retention : 0.3 Micron • Efficiency : 99.97% • Pressure drop: 25 mm of W.c. MOTOR -BLOWERS • Volts : 230 V • Hz : 50 • HP : 1/3 (4 - feet unit) • Amps : 3.5 • Watts : 250 • RPM : 1440 ILLUMINATION: 40 watts Fluorescent tubes NOISE LEVEL: 65 ± 5 db VIBRATION LEVEL: less than 2.5 um (0.0001) POWER SUPPLY: 230 v AC, 50Hz, Warranty: 3 years (on-site)

Biosafety cabinet- Class –II, A2 (Laminar Flow)-- • Product Type: Class II, Type A2 Bio Safety Cabinet • Exterior dimensions (W x H x D) should be 63 x 61.8 x 31.5 inch • Interior dimensions (W x H x D) should be 59.1 x 30.7 x 24.8 inch • Filter Specification should be H14 HEPA EN 1822, 99.995% @ MPPS • Weight should be 507 lbs • Electric requirement should be of Voltage 120 V and Frequency 60 Hz • Certification NSF/ANSI 49, UL, CE • Lighting power should be 120 fc with Two 3 inch plugged cable ports, one on each side wall ,the Receptacles should be of 2 GFI duplex .There should be Service valves Up to 6 total (3 on each side wall) • 8 inch front opening with Sound pressure level should be 64 dB Energy consumption, operating set point 2 should be 280 W, Energy consumption, Night Set-Back mode should be 120 W, Heat output, operating mode (non-vented) should be 955 BTU/hr, Heat output, Night Set-Back mode (lights off, non-vented) should be 410 BTU/hr, Exhaust/inflow air volume 344 cfm, Exhaust volume, thimble ducted 448 cfm. • Armrests must sit above front air intake grill should be easily removable • Programmable UV light extends bulb life and saves energy ,Available UV disinfection cycle • Adjustable UV exposure time saved in memory to facilitate consistent operation • Safety interlock to prevent UV illumination when window is open • One Voltage stabilizer (10KVA) has to be supplied with the machine from reputed manufacturer. • Optional:-Virus burn-out facility. • The machine should have onsite Warranty 5 years.

Deep Freezer (- 20oC) (Vertical)-- • Single door upright freezer, Frost Free • Capacity(L/ Cu.ft): 371 • Shelf/Drawer : 7 • Temp: -16°C -25°C with microprocessor based Temperature controller • Insulation : PUF • Sensor for malfunction :Yes • Sensor for Temperature Controller Malfunction :Yes • Lock : Yes • Provided with Stabilizer • Warranty :2 years (on-site)

Deep Freezer (- 20oC) (Horizontal)-- Horizontal, 500-550 litre capacity, double door, 5- star rating, 100 % cooper wire, Temp: -20°C, Warranty: 1 year (on-site)

Autoclave-- Capacity: 75ltrs, Vertical, Inner Dimension (Dia. x Length): 16*24 inch (400*600 mm), Watt:4KW, Operation Mode :Fully automatic (Digital Controller with Automatic Pressure Release Valve), Construction: Double Walled Inner Chamber Stainless steel 304, External chamber: Stainless steel 304 Lid Stainless steel 304, Ring & Stand: Stainless steel 304 Heater Immersion heater, Gasket: High temperature silicone rubber gasket (Joint less), Locking system Radial locking mechanism w/ pedal lifting device, Temperature range: 121°C to 126°C Temperature accuracy ±1°C • Temperature sensor: PT100 • Controller : • Digital temperature controller • In-built digital timer 0-60 minutes • END of sterilization buzzer alert • Digital display of pressure • Sensor broken indication • Pressure: 15 to 20 psi • Steam release : Automatic steam release after sterilization • Release valve: Solenoid valve • Pressure display: Dial type pressure gauge • Pressure control: Automatic pressure control switch • Safety • Over pressure safety valve • Automatic vacuum breaker • Low water level cut-off sensor • Basket: Wire mesh basket • Power supply:220 Volts 50Hz • Water Inlet Valve • Directly pour into the chamber • Standard accessories: • Water level indicator (glass) • Water drain valve • Warranty: 3 years (on-site)

Biochemical Analyser-- • Microcontroller based semi-automated analyzer to perform routine biochemistry tests (end point, fixed time & kinetic chemistries, multi standard curve calibration & memorization). For estimation of biochemical parameters for veterinary clinics. • Support tests of common domestic, pet & laboratory animals. • Min. 20 most common tests fixed, 20 more can be defined by user. • Bichromatic optic system with different wavelengths. • Should have 8 static interference filters (not filter wheel) with web length selectable from 340- 670nm. • 3 level QC with Levey-Jennings graph. • Support keyboard and mouse with USB port facility to transfer test results from analyzer to computer. • Edit Pre-programmed calculations for kinetic and endpoint assays. • Real-time reaction curve display. • Should be compatible with any commercial Kits/reagents other than OEM reagent as consumables. • Data storage for Min-5000 samples. • Instrument should be CE certified/ USFDA approved. • UPS: 1,000 VA, 360 W, with least 15 minute back- up • Should provide 3 year Warranty and should have OEM Service engineer posted at Tripura for regular prompt service(Documents to be enclosed)

Electrolyte Analyser-- • Sample to be tested: for Na+, Cl-, K+, Ca Blood serum, plasma, Urine. • Semi-Automatic, Minimum aspiration volume not more than 100 micro litre. • Bio-sensor technology based • Large graphic display with touch screen, • Data storage min-1000 samples • Veterinary specific • Process time:≤60 sec • Should have USB port for attaching external Keyboard and mouse supplied should have RS232/LAN port for external device. • Instrument should be CE certified/ USFDA approved. • UPS: 1,000 VA, 360 W, with least 15 minute back- up • Should provide 3 year Warranty and should have OEM Service engineer posted at Tripura for regular prompt service (Documents to be enclosed)

Urine Analyser-- • Automatic Veterinary Urine Analyzer strip based • Parameters - 10 Parameters(Glucose, Protein, pH, Specific Gravity, Leucocytes, Blood, Bilirubin, Urobilinogen, Ketone & Nitrite) • Measurement Principle - Three Wavelength Reflectance photometry Method • Attached waste bin • container • Reaction Time - 60 sec per test • Memory - 2000 Tests • Display - LCD Touch Screen, with in-build thermal printer. • Interface - Micro USB, Blue tooth etc • UPS: 1,000 VA, 360 W, with least 15 minute back- up • Should be supplied with 500 strips. • Warranty :3 year (on-site)

Clinical Haematology Analyser (Five part)-- • Fully Automatic Veterinary Hematology Analyzer (Different species of Domestic & pet animals)- 5 Part, • Method: Electrical Impedance, Light • Scattering, Flow Cytometry, / Calorimetry. • Minimum Parameters (19 items): WBC, LYM#, MON#, NEU#, EOS#, BAS#, LYM%, MON%, NEU%, EOS%, BAS%, RBC, HGB, PCV, MCV, MCH, MCHC, PLT, MPV. • Display screen, 2 histograms and 2 scatter grams • Storage: Minimum 5,000 sample results including histograms, scattergrams and patient information. • Calibration: Manual and Auto-calibration • Maintenance Friendly: 1) Auto-cleaning of sample probe and tubes 2) Automatic fault processing function • Sample consumption: 20uL • For Domestic, Pet &laboratory of animals: such as analysis of samples of Cow, buffalo, sheep, goat, cat, dog, pig, rabbit, rat etc. • Consumables: Supplied Along with a full set of reagents/chemical sets. • Efficiency: 60 samples per hour • Accessories: keyboard, printer, USB etc. • UPS: 1,000 VA, 360 W, with least 15 minute back- up • Should provide 3 year Warranty and should have OEM Service engineer posted at Tripura for regular prompt service (Documents to be enclosed)

Large Animal Sling-- Animal lifting sling, capacity: 1,000 Kg, Fixed & movable with wheel, Iror/ mild steel made, winch gear box facility for lifting, cow handling belt. Size(Min.):7.5x4x4 Ft, Warranty :3 year (on-site)

Animal Examination table-- 4 ft x 2 ft x 32 incl (height) with upper top made with stainless steel solid sheet having slope with fluid drainage facility, four legs made of rust resistant iron.

Video Endoscopy Machine-- • Should be veterinary specific & suitable for companion (Pet) animal as well as large animal. • Gastroscope should have integrated video camera with light source. • Should also have medical colonoscope. • Insertion tube should be of extremely short tip with outer diameter of 8.4 mm, working length should be 1050 mm, working channel should be 2.8 mm. • Should have 4-way deflection (upward 210 °, downward 90°, left 100° and right 100°). • Field of view should be 120 °. • Depth of view should be 3-100 mm. • Should be provided along with a Carrying Case • Caps for Working Channel, Irrigation • Tube, Cleaning Brush, Cleaning Valve. • Should have Biopsy forceps and foreign body forcep. • HD camera system should be compatible with both flexible and rigid endoscope. • Should have internal Medical grade recorder for Capturing Full HD. • Patient’s information should be editable and displayed in monitor. • Should be supplied with Medical Grade Monitor. • Should be supplied with trolley. • UPS: 1,000 VA, 360 W, with least 15 minute back- up • Should provide 3 year Warranty and should have OEM Service engineer posted at Tripura for regular prompt service (Documents to be enclosed)

Small Animal USG Machine-- • It should have minimum 15’’ LCD monitor with 30 degree tilt function Compact and streamlined design. • It should have dual universal transducer connectors • There should have backlit keyboard • It should have 1hour uninterrupted scanning with rechargeable battery • It should have Scanning modes like:- B, B/B, 4B, B/M, M/P/W mode • The Pulse wave graph should appear in color • It should have Quick image optimization with one- click button • It should offer Instant full screen zoom with one- click • It should have offer Patient database review and analysis platform • It should have Storage capacity of minimum 1 TB • It should offer Tissue Harmonic Imaging on all probes • It should have Smart 3D enabled on all the probes. • It should offer panoramic imaging • It should have 256 grey scale • It should offer speckle reduction feature • It should have Multiple image formats: BMP, JPG, DCM, AVI, DCM, CIN • It should have Specialized measurement and analysis packages for different animals and • dedicated Veterinary transducers with anti-decay surface and longer cable • It should have Professional Package for Veterinary Use and Veterinary information management, Veterinary body mark, Veterinary comments and Veterinary OB table • It should be Supplied with two probes: • One Micro convex probe (Freq. 5-8.5 Mhz) suitable for small animal abdomen and cardiac • One Linear probe (Freq. 5-10 Mhz) suitable for small parts scanning. • The system should be warranted for minimum one year. • They should have a service centre with service engineer for support at Tripura. • The brand quoted should be time tested and have its presence and installation base of at least 20 units across the country at the veterinary institutes by the bidder only irrespective of model installed by the bidding company itself. Please attach supply orders/installation report or performance certificates in support of your bid. • The product offered should be CE marked. • UPS: 1,000 VA, 360 W, with least 15 minute back- up • Should provide 3 year Warranty and should have OEM Service engineer posted at Tripura for regular prompt service (Documents to be enclosed)

Spectrophotometer (Double Beam)-- • Sample Cell Holder: 8 Cell Holder • Programmable 10mm • Bandwidth: 1nm • Reference Cell Holder: 10 Cell Holder • Optical System: Double Beam(1200 Lines/mm Grating) • Wavelength Range: 190-1100nm • Bandwidth: 1nm • Wavelength Accuracy: ±0.3nm • Wavelength Repeatability: ±0.2nm • Scanning Speed: Fast, Medium & Low • Photometric Accuracy: ±0.3%T • Photometric Repeatability: 0.2%T • Photometric Range: -0.3-3A,0-200%T,0-9999C • Stability: ± 0.001 A/h @ 500nm • Baseline Flatness: ±0.001A/h • Noise: ±0.001A/h • Stray Light: 0.05%T @ 220nm,360nm • Data Output Port: USB • Printer Port: Parallel Port • Display: LCD • Light Source: D2 Lamp & Tungsten Halogen Lamp (W Lamp) • Detector: Silicon Photodiode • Power Supply: AC 220V,50/60Hz • Standard Accessories- Quartz cuvette with 10mm path length 4 numbers, • Local Accessories- PC with UPS is to be offered with the system • Warranty: 3 year (On-site)

ELISA Reader-- • The Light source should be of Quartz halogen lamp 6 V/10 W • The Wavelength range should be 340–850 nm • There should be 8-position filter wheel with 3 filters 405 nm, 450 nm, and 620 nm filters installed with additional filter of 492nm • The Filter half-bandwidth should be 3–9 nm • The Read-out range should be 0–6 absorbance units (AU) • Linearity (at 405 nm) should be ±2% (0–3 AU, 96- well plate) • The Resolution should be 0.001 AU • The Accuracy (at 405 nm) should be ± 1% (0–3 AU) or ±0.003 AU (whichever is greater) • Co-efficient of variation of Precision (at 405 nm) should be ≤0.2% (0.3–3 AU) • Measurement speed should be 7 sec (fast mode, 96- well plate) and 13 sec (normal mode, 96-well plate). • Linear shaking should be slow, medium, and fast modes • The machine should have High-contrast colour display (480 x 272 pixels) • There should be On-board display or PC control user interface • Internal memory (stand-alone) of up to 99 assay protocols and 100 test results (96-well plate) should be there • There should be USB port for PC and USB port for data export to USB memory device • The main input should be of 100–240 V (50/60 Hz) • The Power consumption should be of Max. 100 VA, 8 VA in standby mode • The Overall dimensions (H x W x D) of the product should be 8.7 x 11.4 x 15.7 inches (22 x 29 x 40 cm) • The weight of the product should be 8.5 kg (18.7 lb) • The machine should have Regulatory conformance of 2004/108/EC (Electromagnetic Compatibility Directive, EMC), 2006/95/EC (Low Voltage Directive), 2006/42/EC (Machinery Directive), FCC Part 15, Subpart B/Class B, 2011/65/EU (RoHS Directive), 2012/19/EU (Waste of Electrical and Electronic Equipment) • Suitable Software for result analysis should be supplied along with the machine for use with the PC. • The machine should have onsite warranty of 3 years. • One Additional ELISA Microplate washer has to be supplied with the machine with the following specifications • The washer should be of 96-well Plate format with One number of wash buffer bottles • One number of wash buffer bottle (2 litre) and one waste bottle (2 litre) whould be supplied with the machine • 1 x 8 wash head should be included • The range of wash volume should be 50–1,000 μLwith Prime/rinsing volume 5–100 mL and Dispensing volume 50–400 μL • The Residual volume should be 2 μL • There should be USB port for data transfer • The Dispensing accuracy should be less than 5% error for 300 μL and Dispensing precision 3% (CV) for 300 μL • Number of wash protocols to be saved should be Up to 99 • The Dimensions (H x W x D) of the machine should be 13.6 x 15.2 x 9.4 inch.(34.5 x 38.5 x 24 cm) • The Weight of the machine should be 8 kg (17.6 lb.) • The machine should have onsite warranty of 3 years. • Machine should be supplied with one 2 KVA online UPS of reputed manufacturer • Additional data display and storage with following specifications: • Processor: i7-1255U (3.50 GHz up to 4.70 GHz) 12MB & 10 Cores // RAM: 16GB, 2x8GB, DDR4, 3200MHz // Storage: 1TB HDD + 512GB SSD • Software: Win11+MS Office 21 + McAfee 15 Months • Display: 27.0" FHD WVA AG Narrow Border Touch, Graphics: NVIDIA GeForce MX550 (2GB GDDR6), Keyboard and Mouse: Wireless, Warranty: 3 Years Onsite Hardware Service • Ports: 3 USB 3.1 Gen 1 ports with Power on/Wake- up support, 1 USB 3.1 Gen 2 port with Power Share, 1 USB 3.2 Gen 2 (Type-C) port, 1 universal audio jack, 1 HDMI 1.4b port, 1 HDMI-in 1.4b port, 1 RJ-45 port, 1 SD-card slot • Features: Pop-up FHD Camera with Tilt / 2x5W speakers / Bluetooth Speakers / Swivel Monitor / Type C port • Warranty: 3 year (on-site)

Incubator (Bacteriological)-- • Temperature Range: 5°C above ambient to 60°C • Temperature Accuracy: ± 0.5°C • Temperature uniformity: Better than ± 2°C • Standard Models: Inner Stainless steel 304, 0.8 mm &Outer mild steel, 1.0 mm powder coated • Capacity: 200 Ltrs. • No. of Trays: 3 • No. of Doors: Single • Control System: Microcontroller based temperature indicator cum controller with Digital display and PT100 sensor. • PC Interface: ThroughRS-485 • Memory: 500 Records • Alarm: Audio Visual Alarm if the temperature deviates from the preset temperature • Heating System: U shaped S.S. Nichrome wire air heaters • Air Circulation: Motor and blower arrangement to have uniformity of temperature under loaded condition. • Insulation: 3" Thick CFC free PUF Insulation. • Lighting: Interior illumination for working area. • Observation Door: Inside see through unbreakable acrylic door • Validation Port: 50mm validation Port with silicone rubber seal to insert sensors for validation purpose. • Trays: Specially designed solid stainless steel wire mesh trays ensure even temperature distribution • Other: Castor wheels, mcb, adjustable tray height arrangements, heavy duty latch with lock & key • Power: Works on 230V AC single phase 50Hz. • Safety feature: Additional safety thermostat to cutoff the air heater in case of over shoot of temperature • Certifications: ISO9001:2008, ISO 13485:2012 • Documentation: LABTOP will provide IQ, OQ, PQ documents with Material Test Certificates and Calibration reports • Warranty: 3 years

Monopan Digital Balance-- • Display: LED touch screen • Special built-in- applications: net total, totalizing, statistics, weighing, mass unit conversation, animal weighing. • Protection: chemical resistant finish • Password protection: single level password protection • Anti-theft lock: Kensington lock and lockdown capability for cable or chain. • ID creation: sample ID and batch ID creation possible. • Interface: -USB type C interface - Industry Proof RS232 9-pin interface - Backward Compatibility (by Using RS232 port) - Data transfer: direct data transfer to Microsoft windows programs. • Weighing pan: best repeatability with rectangular weighing pan. • Language: English. • Technical specification: - Weighing capacity: 220g - Readability: 0.1mg - Repeatability: 0.08mg - Linearity:0.06mg - Typical stabilization time:1.5sec - Typical measurement time : 2 sec - Weighing chamber height :240mm - Weighing pan size:90mm - Warranty: 02 years (on-site)

Physiograph-- Standalone unit having coloured TFT display for displaying online and offline recording data. Systems have sic couplers fitted in as single unit easy to carry. System shall have Eight transducers (Force, Pressure, Volume, Respiration, Temperature, Pulse, Respiration Belt and Isotonic). Facility to store recording data and review the same on TFT. Interface to the computer – Through USB. System provided with software to review and printing the recorder data from PC. Accessories like ECG electrodes, EEG electrode, Bio Potential Junction Box, EMG disc electrodes, Ground electrode, EEG Paste, ECG gel, etc. should be provided. Warranty :3 year (on-site)

Micro haematocrit Centrifuge-- Speed range of 200-14,000 rpm, max. RCF 18,620 x g. Independent control of speed and time. Easy operation with intuitive menu and easy-to-read display. Included hematocrit rotor: 24 capillary capacity, max. speed of 12,000rpm. Optional tube rotor: 24 place 1.5/2mL capacity. Warranty :3 year (on-site)

pH Meter-- • pH Range: -2.00 to 14.00 pH • Resolution/ Accuracy: 0.01 pH/± 0.01 pH • ORP Range : ± 2000 mV • Resolution/ Accuracy: (± 199.9 mV) / 1 mV (beyond) ± 0.2(± 199.9 mV) /± 2 mV (beyond) • Temp. Range: 0 to 100 °C (32.0 to 212.0 °F) • Resolution/Accuracy: 0.1°C(0.1 0 F)/±0.3 °C/±0.5°F (0 to 70 °C) • ATC: Yes (0 to 100 0 C) • Buffer Options USA : pH 1.68, 4.01, 7.00, 10.01, 12.45 , NIST: pH 1.68, 4.01, 6.86, 9.18 , 12.45 • No. of pH Calibration Points: 5 points • Built-in Electrode Arm: Yes • Memory : 100 Data sets • Electrode: Included, single junction pH electrode • Temp. Probe: Included • Power Requirements: Included, 100 /240VAC, SMPS Power Adapter with US/UK/EUR/Japan plug ,9V,6W, CENTRE +ve • Warranty: 3year (on-site)

Flame Photometer-- Range : Na: 0 – 100 ppm, K : 0 – 100 ppm, Ca: 15 – 100 ppm, Li: 10 – 100 ppm (Optional). Sensitivity : Na: 5 ppm, K : 5 ppm, Ca: 10 ppm Li: 10 ppm Accuracy : + 2% upto 40 ppm, + 5% above 40 ppm Warm up time: 10 minutes. Power: 230 V + 10% AC, 50 Hz Warranty: 02 years

Binocular Microscope-- • STAND: Single Mould, die cast sturdy stand with anti rust material with textured paint, with ergonomic extended base for hand rest and greater stability, anti-fungal mould treated. • VIEWING BODY: 30° inclined Siedentopf Binocular tubes, 360° rotatable with IPD 50- 75mm. Anti-fungal mould treated. • EYEPIECE: Wide field paired eyepiece, high quality, and achromatic 10x/20 mm with dioptric adjustment. Antireflection coated & Anti-fungal mould treated. • NOSEPIECE: Backward angle, Quadruple revolving Nosepiece (ball bearing type), with soft rubber grip. • OBJECTIVES: Infinity Plan Achromatic objectives, antireflection & anti-fungal mould treated, 4x/NA 0.10, 10x/NA 0.25, 40x/NA 0.65 SL, 100x/NA 1.25 (SL, Oil) • STAGE: Double layered graduated mechanical scratch proof rectangular stage size 142 x 133mm, X/Y cross travel range 76 x 54mm. Co-axial controls, spring clip, Low drive right hand movement controls, double specimen holder, anticorrosive coated. • COARSE & FINE FOCUSING: Focusing Co-axial coarse and fine focus on ball drive system and brass metal gears for smooth operation with torque adjustment on one ring side. • Warranty :3 year (on-site)

Trinocular Microscope with Photography Unit-- Microscope: Type: Upright bright field compound Trinocular microscope with Koehler Illumination Control Display: 5-element display on either side of the stand and long-life blue LEDs which is well readable from several meters distance. Illumination: 3W LED warm-light, 3200K, lifetime-25000 hours, Homogeneous field illumination 20mm, can perform plug-on swivelling mirror Optical system: Color-corrected infinity optics Eyepiece: A pair of e 10x suitable for spectacle wearers and retro fittable eyepiece with pointer; Eyepiece with field of view of 20mm; Eyepieces secured with setscrews against unauthorized removal. Objectives: Plan-Achromat: 4x, 10x, 40x, 100x, with 4-position nosepiece tilted back and objectives secured against unauthorized removal Condenser: Focusable and centreable Abbe condenser 0.9/1.25 Viewing Tube: Trinocular Tubes (50%:50%) with 25° angle and field of view 20 mm; Viewing with 30° angle and field of view 20mm for Height adjustable siedentopf tube; Siedentopf "up and down" position for 2 different viewing heights. Stage: Mechanical reckless stage with Long-lived stage surface; With well-readable vernier and robust controls; Stage size- 140x140, travel range 75x40; Extremely stable stand to broad base and low center of gravity. Power: With power unit integrated into stand by way of a parking position with cable storage in the stand rear wall. Ergonomic shape for convenient, safe carrying; With IEC adapter for conversion into a bench-top power pack; With external unit that is easy to change in case of defect ; With Power of 100- 240V and 50-60Hz. Carrying Handle: With carrying handle that is completely integrated into stand; With ergonomic shape for convenient and safe carrying Dust cover: With dust Cover Anti-fungus treated optics: Must provide anti-fungus certification from manufacturer. • Should provide schematic diagram of microscope • System should be ISO and European CE Certified (provide document) • After Sales & Service Support should be available in Agartala (provide contact no. and address). Warranty: 5 years warranty for microscope Digital Imaging System: • A 8.3 MP Digital Microscopy Camera with • facility for standalone operation as well as in PC. • Facility available for Live Image on screen • Display Direct image • Recording and Capturing along with Image • Analysis Software • Camera package shall contains the following accessories: o USB 3.0 hub Type-C, o USB 3.0 flash drive, Type-C and Type-A o USB 3.0 cable Type-C to Type-A o Power (&) signal cable camera to microscope o stand with suitable Power adapter - Export into ZVI, BMP, GIF, JPG, PNG, TIFF, HDP image formats. - Sensor: Sony CMOS image sensor Color, Rolling Shutter Number of Pixel: 3840 (H) x 2160 (V) = 8.3MP, Ultra HD (4K) Selectable Resolution: 3840 x 2160 and Full HD (1080p) = 1920 x 1080, Pixel size: 1.85 μm x 1.85 μm, Effective Area: 7.1 mm x 4.0 mm, IR filter. - Entire System i. e. Microscope, Camera and Software shall be from same manufacturer. - Warranty: 2 years (on-site) Additional Data Storage Unit: • Operating System: Windows 11 Home • Processor: 12th Generation Intel Core i5 (up to 4.4 GHz) • Memory:8 GB DDR4-3200 MHz RAM • Storage: 512 GB SSD storage • Graphics: Intel® UHD Graphics 730 • Moinitor: size- 60.5 cm, FHD (1080p) with IPS display • Pointing Device: Wired Mouse • Keyboard: Wired • Should include Genuine Microsoft Office Home & Student 2021 Lifetime Subscription • Warranty: 3 years (on-site) • 03 years Quick Heal antivirus protection subscription • UPS: 1,000 VA, 360 W, with least 15 minute back-up

Micropipette set-- • Kit should includes 0.2-2, 2-20, 20-200 & 100-1000 ul Single Channel Pipettes, 1 Pipette Stand (6 Position), 4 Sizes Tip Boxes with Tips, Reagent Reservoir Sample, Calibration Certificate • Also included extra two pipettes 1-10ul, 10- 100ul. • Fully Autoclavable • Advanced volume gearing mechanism • Should have large, easy-to-read display • Double-action pipetting button with a rotating upper part, for easy and light volume setting. • Should be light weight, least RSI (Repetitive Strain Injury) • Ergonomic design, separate soft touch tip ejector • In lab calibration and easy maintenance, easy to open • Super blow out piston for small volumes to ensure delivery of micro size drops • Should be ISO and USFDA Certified (provide document) • 2 years warranty

Desktop Computer-- • Operating System: Windows 11 Pro (original) • Processor: Intel® Core™ i7-12700 (up to 4.9 GHz with 25 MB cache and 12 cores) • Memory: 8 GB DDR4-3200 MHz RAM • Storage: 1TB HDD + 512GB SSD • Graphics: Intel® UHD Graphics 770 • Chipset: Intel® Q670 • Connectivity and Communications: intel® Wi-Fi 6E and Bluetooth® 5.3 wireless card • Ports: 1 headphone/microphone combo; 1 USB Type-C 10Gbps signaling rate; 3 USB Type-A • 10Gbps signaling rate • Video Connectors: 1- HDMI 1.4; 1- Display Port 1.4; 1- VGA • Monitor: size- 60.5 cm, FHD (1080p) with IPS display • Pointing Device: Wired Mouse • Keyboard: Wired • Should include original preinstalled latest version Microsoft Office Home, & Student 2021 Lifetime Subscription and 5 years Quick Heal antivirus subscription • UPS: 1,000 VA, 360 W, with least 15 minute back-up • Warranty: 03 years (on-site)

Distillation unit-- • Capacity Distilled Water Output: 1.5 LPH • Minimum cooling water requirement (Ltr/min): 1 • Heater: Quartz • Boiler: Boro 3.3 • Condenser: Boro 3.3 • Biological Activity: Pyrogen Free • Conductivity S/cm*:3 × 10-6 • Power consumption (kw): 3 kW • Voltage (V) : 230V • Dimensions (L × B × H) in mm: 640 × 630 × 520 • Warranty: 2 years

Rotary Microtome-- • Designed for effortless manual sectioning via a counter-balanced and smooth-running hand wheel. • Instrument with X/Y specimen orientation • Fast exchange system for specimen clamps, both Universal & Standard types • Personalized user selectable coarse feed wheel turn direction, either clockwise or anti-clockwise to suit user’s preference • Retraction on/off function • Two mechanical trim steps: 10 μm and 50 μm • Blade holder for disposable blades –must be suited for both high & low profile blades and standard specimen clamp. • The object head with +/-8° X/Y orientation equipped with a fast specimen clamp exchange system for improved workflow. • Space on top of the instrument housing for storage of sectioning tools and accessories. • Maintenance-free vertical cross-roller guides and horizontal specimen feed via precision cylinder guide system. • Distortion-resistant base plate to ensure optimum overall stability. • The vertical stroke of 59 mm • Horizontal specimen travel range of 25 mm • Allow to section specimens up to a size of 50 mm x40 mm x 40 mm. • Ergonomically designed hand wheel grip. • Hand wheel lockable in any position via brake lever attached to base plate • Operating conditions o Operating temperature range 10°C to 35°C o Temperature range during storage 5°C to 55°C o Relative humidity max. 80%, non– condensing o Storage humidity 80% • Technical information • Section thickness setting range 0.5–60 μm • Section thickness selection from 0.5–2 μm in 0.5 μm-steps • from 2–10 μm in 1 μm-steps • from 10–20 μm in 2 μm-steps • from 20–60 μm in 5 μm-steps • Total horizontal specimen feed 25 mm • Vertical specimen stroke 59 mm • Specimen retraction ON/OFF • Specimen orientation • Horizontal 8° & Vertical 8° • Rotation ± 90° • Dimensions and weight (Preferred) • Width 438 mm 17.24” • Depth 472 mm 18.58” • Height 265 mm 10.43” • Working height (knife edge) 105 mm 4.134”; Weight (without accessories) 27-30 kg. • Should have more than 40-50 installations only in East India, with 50% being in reputed Govt. Institutions (provide documentary evidence). • Must be CE & USFDA certified/approved (provide documentary evidence). OEM: Sakura/ Leica/ CellPath/ Tanner Scientific • Should have dedicated OEM’s own Company Service Support for Eastern/North-Eastern India with company’s own factory trained service engineers based in East/ North-Eastern India to provide prompt support (provide documentary evidence). • Warranty: 5 years (on-site)

Paraffin Floatation Water Bath-- Four Racks - Double Walled, inner made of SS sheet & outer of MS sheet. Heating is done by strip type heaters & 2" thick fibre glass wool insulation is provided. Temperature range shall be from Water Temp. / Ambient to 100oC, +/-0.5oC, controlled by a Digital Indicator Cum Controller with Lid & Trays. Operated on 220V A.C. Mains. Provided with Powder Coating Paint Finished. Warranty: 3 years (on-site)

Scalding Tank (Stainless Steel)-- Tank capacity-30-40 litres, Voltage: 220-240 V. Control panel with digital temperature indicators. Material: Stainless steel, Type: Electrically operated.

Electric Stunner-- Stunner with tongs made of SS with isolated handles to operate on sheep/goat and pigs. Shock proof control box with analog display for volt and ampere. Variable stunning voltage. Electrical supply from the control box to SS tongs through electrical cable. • Voltage: 230 V +/- 10% • Frequency: 30-50 Hz • Stunning Voltage: 80-400 VAC • Stunning Current: 1.5 Ampere

Captive Bolt Pistol-- • Non-penetrative concussion stunner • Universal in application from large bulls to small lambs, with varying power load strengths • Well balanced, comfortable ergonomically designed handle • Automatic bolt return • Standard tool in 0.22 or 0.25 calibre. • Robust solid construction. • Features/Specifications: • Chrome steel finish • Knurled handle for better grip • Fewer parts than competitive brands • Bolt penetrates 2.25"

Portable Colour Analyser-- Digital colour meter that measures colour in LAB colour values and finds Delta E colour difference between master and samples using NR series colorimeter. Warranty: 02 year (on-site)

Muffle Furnace-- Temperature range up to 1000oC, working temperature up to 950oC, size 19 x 16 x 18 (L X W X H) inches, 220/230 volt, Warranty: 02 year (on-site)

Micro Kjeldahl Apparatus-- Horizontal, MS powder coated with 6 heaters with energy regulator control, maximum temperature approximately 4000C, capacity for heating of 500 ml Kjeldahl flask, Warranty: 02 year (on-site)

Mixer Grinder-- No of Jars: 3; Jar Size: Wet Jar (1.5 Litres), Multipurpose Jar (1 Litre), Chutney Jar (0.3 Litres); Jar Material: Stainless Steel; Body Material: ABS; Blade Material: Stainless Steel; Speed Control: 3 Speed Control + Pulse, Wattage: 1000W; Voltage: 230 V, Warranty: 01 year (on-site)

Lab Willy mill-- Body Material. MS, Power Source. Electric, Voltage- 240 V, Frequency- 50 Hz, Power Consumption- 0.75 kW, Load. 43 Kg.

ECG machine-- • 3 Channel ECG Machine with Automatic interpretation. • Simultaneous 12 Leads acquisition and 3 ch recording. • 4.3” inch colour TFT LCD display ECG Wave. • Support touch panel and key pad input ways. • Built in USV / RS 232 interface (ECGNET Software) • Built in rechargeable Li-ion Battery support less than three (3) hours continuously work. • Warranty :3 year (on-site)

Digital Camera-- Dimension: Width – 125mm, Length – 64, Height – 96mm, Thickness – 76.5mm Megapixel: 24.2MP, Focal Length: 18 – 55mm

Cow Replica Model-- Approximately one sixth the size of the real cow, this cow models shows the internal and external anatomy of a female cow, including ruminant system, reproductive system and digestive system. Model includes: 1. Model on display stand 2. Cross sectional view of internal and external anatomy 3. 13 removable parts 4. Quick start guide 5. Online access to curriculum, students activity and presentation slides 6. (2) ( 20” X 30”) posters :Beef cuts and cow anatomy 7. 1 year limited warranty 8. Dimension : 10”X21”X33./5” 9. Weight : 45 lbs 10. 13 detachable parts Curriculum : 1. Cow anatomy 2. Digestive tract 3. Reproductive tract • Presentation slides , students assessment tools

Large Dog Model-- The Large Dog Model is a detailed model of a large- breed female dog. Featuring internal and external anatomy, it splits in half to reveal removable organs. Additionally, incorporate the included curriculum for a complete experience. Package includes: • Model on display stand • Cross sectional view on internal and external anatomy • 10 removable parts • Quick start guide • Online access to curriculum • 1-year limited warranty Product Dimensions: 15” x 27” x 30” Product Weight: 47 lbs. 10 detachable parts Curriculum : Lessons topic : 1. Canine Anatomy 2. Digestive Tract 3. Reproductive System Includes Presentation slides, Students activity and assessment tool

Cow Anatomy 3D Flip Chart-- The Cow Anatomy 3D Flip Chart is a portable relief chart that splits down the middle to reveal 3 separate bovine anatomical illustrations: the outer view of the cow, the skeleton and internal organs and reproductive tract. It is one-sixth the size of an actual cow and features white board material. Use it to teach bovine anatomy and other bovine systems. It includes hindquarter, hoof and reproductive tract callout diagrams. Cow Anatomy 3D Flip Chart includes: • 3 contoured flip charts: exterior anatomy, internal skeleton and organs and internal organs • Tabletop stand • Floor stand on wheels • Online access to curriculum • 1-year limited warranty • Made of white board material for use with most dry erase markers • Weight: 35 lbs. • Dimension: 18” X 40” X 32” Curriculum Spotlight 1. Bovine Anatomy Presentation slides and students assessment tool

Demonstration Model of Cow-- • Natural size, detachable skin to show superficial and deep muscle. • Head and neck detachable and dissectible. • Viscerae are dissectible to demonstrate various systems within the organ are also detachable. • Detachable hoof

Exhibition Panel/ Panel Board with stand-- • Application: Exhibition Panel • Size: 4x 36 inch, Height: 6-8 foot • Material: PVC • Shape Rectangular

RMS Speakers-- SRX-120DX, 100Watts, STA-150, With tripod stand of height adjustment : 3.5ft-6.5 ft, Load Capacity; 40 Kg, Warranty: 2 years

Wireless Microphone-- Audio Output:0110mV/600,Freq. Resp: 50-14000Hz, Antenna: Detachable through BNC Connector, power: AC-220-240 for AC adopter, Modulation Made : FM(F3E), Warranty: 2 years

Amplifier-- AC & 24V DC Operated, 250 Watts,6Mic & 2Aux, Warranty: 2 years

Public Address with Speaker-- Amplifier: WA-320/AWM-321, Warranty: 2 years

Interactive board-- Size - 86’’ with 4k Ultra High Definition (3840 x 2160) @ 60 Hz with OLED display technology with 8 ms response time, 20 points IR multi touch interface, 3 HDMI, 4 USB, Bare dimension of 1990 x 114 x 1201 mm with 320 W power consumption, build in android 8.0 with 3 GB RAM and 32 GB ROM with OPS i5 or i7 8 GB RAM and 1 TB SSD, Built in wifi, warranty period:- 2 years from the date of installation

Video Camera (HD)-- • Product Dimensions: 33 x 22 x 28 cm; 1 kg • Flash memory type: SDHC • Resolution: 4k • Compatible Devices: Laptop • Special Features: Face Detection • Mounting Hardware: Camera Recorder, Li-ion Battery Pack (7.28V), Adaptor (12V), AC Cable, Eye Cup, Handle Unit, Mic Holder, O/I • Number of items: 7 • Display Technology: OLED • Standing screen display size: 3.5 Centimetres • Image stabilization technology: Digital • Image Stabilisation: Yes • Optical zoom: 24 x • Digital zoom : 24 x • Min Focal Length: 23 • Video Capture Resolution: 4K • Batteries Included: No • Batteries Required: Yes • Wireless Type: 2.4 GHz Radio Frequency • Connector Type: Wi-Fi • Form Factor: Compact • Lens type: Zoom\ • Warranty: 2 years (on-site)

Antibiotic zone reader-- Digital display range : 0 mm to 35 mm, readability 0.1 mm, warranty: 2 years

Hot Plate Analgesiometer-- 30x30 cm heating surface with perpex enclosure micro controller based digital temperature indicator Temperature range : 30-80 c Warranty: 2 years (on-site)

Plethysmometer-- Digital display with pedal switch control, Warranty: 2 years (on-site)

Magnetic stirrer with bar-- With pivot ring , dimension 6x10 mm, 9.5x40 mm, 12.7x 76, 8x65 mm Warranty: 2 years (on-site)

Small Animal Anesthetic Apparatus-- • Respiration mode Manual mode, open mode, closed mode, semi-open and semi-closed mode. • APL valve should adjustable easily, range: 0-60 cm H2O and there should be one safety pin top of is there is high pressure should be released easily. • It is easy to clean the dirty and the color is black. • It is a 0-4L/m high precision flow meter which is very available for small animal usage. • It has a select bar technology, which is easy to change the anaesthesia vaporizer with one switch. • The Vaporizer should be made by stainless steel with key filler. • The CO2 circle absorber has inspiration valve and expiration valve, which have plastic cover to observe the animal breath clearly for doctors. • The CO2 circle absorber has a high-quality soda lime chamber, which is poly-carbonate (PC) material for medical usage. It is very strong and not broken and should have 500 gms capacity. • It has an option for platform on the top, where the patient monitor is put. • The structure is very reasonable for doctor to use this machine alone: the flow meter is on the left, the vaporizer is on the middle, the CO2 circle absorber is on the right, the airway pressure gauge should be top of absorber, which can monitor the airway pressure of close system. And the O2 flush is on the left top of flow meter for easy operate. • This machine is very small to save the space of the operation room. • This machine can be put on the trolley, also can be put on the table at the same time can be put on our wall mount arm. • Warranty: 2 years (on-site)

Multi parameter vital signs monitor-- • Monitor should have integrated non-invasive, invasive measurements & features suitable for small, medium and large animals. (Cat & Dog ) • Should have TFT/LCD display with at least 12.1 inches with numeric display simultaneously. Should be capable of customized display. • Should be compact & portable with carrying handle. • Should have facility to monitor ECG, HR, SpO2, Resp., NIBP, Respiration & Temp. & optional: - 2IBP & Etco2 . • Should have Equipped with the accessory box, the medical staff will be more convenient to store and take out the accessories. • Should display at least 8 waveforms of selected parameters. • Should be able to store & display at least 120 hrs. of graphical and tabular trends of all parameters and minimum 2000 groups of NIBP measurement. • The SpO2 technology should also sense in low perfusion. PI (Perfusion Index) should be displayed on the screen. • Monitor should have ST segment calculation with facility to detect life-threatening arrhythmia. • Should have internal rechargeable battery for 2 hours monitoring or more. • Should have audio/visible alarm. • Should have ESU & Defibrillation protection. • Should have drug calculation, hemodynamic calculation, ventilation calculation, oxygenation calculation & renal function calculation as standard features. • Other bed observation should be there as standard feature. • Warranty: 2 years (on-site)

Hydraulic OT Table-- • Two panel table top system that adjusts form horizontal to near vertical to hold the pets the design position during surgery. • Overall size of the top: 20”W x55”L. • Powerful and durable electric lifting actuator holds 120Kgs on the surgery top. • Improved waster channel and drain hole design allow for fluidly drain flow. Close fitting translucent bucket improves waste collection. • Buffered hinges and air spring added to cushion the dropping impact of the whole top and V-top side panels. • The IV pole mount is selded on. • Table can be lifted form 28” to 47”. • Workshop Swivel Angel 0°-45°. • Buffer hinge. • Heating system with accurate temperature monitoring and control. • Category: Operation Table & amp; Light • Warranty: 2 years (on-site)

Shadow less Lamp-- • The LED Bulbs that are fixed into this is meant for saving power consumption • The Sterile handle Present in this equipment helps in easy adjustment. • The operating light designed for the use in high demanding surgeries. • LED bulbs used to ensure low energy consumption and long service life. • Light head is resistant to disinfectant, easy to clean. • LCD Display for showing all important parameter like intensity/on/off. • Flexible and stable balance arms suspension system for height and angle. • Light Intensity: 2,40,000 Lux • Number of LED’s: 72 • Life span of LEDs: 50,000 hrs • Focus Dia: 15-25 cm • Power supply: 160V-240V DC, 50Hz Control Unit: SMPS • Dome size: 500mm • Spot Diameter: 125-150mm • Colour Temp. 3500-4800k • Power Supply: 220v/50HzAC • Power consumption: 40Watt • LED Average Light: 50000 Hrs • Intensity Control-30-100 • Warranty: 2 years (on-site)

Electrocautery machine-- • Should Have Microprocessor Controlled Surgical Generator • The unit should comply with safety requirement of IEC60601-1 & IEC 60601-2-2 and test report for each power setting need to be present. • The equipment should have brand name / model name mentioned on the equipment. Original Literature of the Manufacturer needs to be given • Machine should be able to monitor changes in tissue impedance • Number of coagulation modes should be 4 • Maximum power in coagulation mode should be 150w • Number of bipolar modes should be 3 • Maximum power of bipolar mode should be 120w • Should have patient plate monitoring facility • Should have 1 hand switch & 1 foot switch for monopolar mode & 1 foot switch for bipolar mode • The system should have facility to use two monopolar coag modes simultaneously • Should have touch screen keyboard / membrane pad for power settings • Should have lcd / led display • Should have 3 segments for the display • Should have individual display for bipolar and monopolar cut and monopolar coagulation • Rf leakage current should be 100ma • The power supply should be 230v (±15%) 50hz • Type cf equipment (iec 601 –1 & iec 601-2- 2) defibrillator proof. Various modes in electrosurgical unit: a) mono-polar cut: 1. Pure cut: 300- 400 w 2. Low cut: 300-400w, 3. Blend: 200 -250 w, b) mono-polar coagulation: 1. Spray: 120 w 2. Fulgurate: 150 w 3. Desiccate: 120 w c) bipolar coagulation: 1. Cut/precise: 70-120 w, 2. Force/standard: 70-100, 3. Micro/Macro: 70-100 W • Auto Start coagulation & auto stop coagulation Input Power source: Operating • Range: 170-260 VAC Line Frequency: 50-60 Hz Minimum High Frequency Leakage • Bipolar Less than 60mA Monopolar less than 150mA Standard Accessories to be provided: 1. Reusable/Disposable dual pad Silicon/ Polyhesive Plate with cable 2. Bipolar forceps with cable 3. Mono polar-hand switch pencil 4. Dual pedal foot switch for Mono-Polar 5. Single pedal foot switch for bipolar 6. Power cord • Unit should have patient plate Contact Quality Monitoring System/REM System- With this at the moment the contact between Plate & Patient reduces, it stops the HF delivery & gives error message with audio visual indications • The system should have Return Electrode Contact Quality Monitoring (REM) System preferably with Adaptive REM facility • The system should have facility to use two monopolar coag modes simultaneously • The system should have ability to restore last power setting • Machine should be able to upgrade to a higher version • The unit should operate at local climatic conditions & up to temperature of 40 degree Celsius. • Warranty: 2 years (on-site)

Electric dehorner-- • Material: Stainless Steel • Automation Grade: Automatic • Product Type: Electric and stainless steel • Capacity: 50 HZ • Warranty: 2 years (on-site)

Community nest box-- • Product Dimensions: 45.6"L x 13"W x 26"H • Material: Alloy Steel

Feed grinder (Mini)-- • Capacity: 300 kg per hour • Motor Power: 2 hp • Dimensions (LxWxH): 110X125X185mm • Weight: 50kg • Material: Mild Steel • Hammer Size: 14 inches • Number of blades: 20 • Automation Grade: Automatic • Frequency: 50Hz • Voltage: 440V • Warranty: 2 years (on-site)

Feed mixer (Mini)-- • Capacity: 100 kg • Motor Power: 3 hp • Material: Mild Steel • Mixing Chamber Volume: 100 liters • Motor rpm-1440 • Foot mtg • Gear shaft arrangement rpm -35 • Very high quality and strong construction in MS • Warranty: 2 years (on-site)

Milking Machine-- • No of Buckets: 1.0 • Productivity: 1-10 cows/hour • Capacity: 25 Litre • Automation Grade: Semi-Automatic • Power Input (W): 110W • Voltage (V): 110-220V • Frequency (Hz): 50/60 Hz • Warranty: 2 years (on-site)

Incubator (Hatchery)-- • Egg Capacity: 500 egg • Temperature Range: 37.5 Degree C • Inner Material: Hylum • Bird Type: Chicken • Dimensions(LXBXH): 52 x 42 x 36 inch • Automation Grade: Automatic • Humidity Range: 99% • Voltage: 220 V • Weight: 78 kg • Hatching Rate: 85% • Usage/Application: Poultry Farm • Frequency: 50-60 Hz • Phase: Singe Phase • LED Display: Yes • Power Consumption: 200 Watt • Warranty: 2 years (on-site)