The Singareni Collieries Company Limited Tender

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Providing and fixing Thermocole False ceiling 600mmx 600mm using 19mm thick Thermocole sheet, anodised Aluminium Tee sections of size 24.50mm x 24.0mm x 2.4mm in grid with cross tee of size 24mm x 24.5mm x 2.4mm at every 600mm c/c and anodised aluminium wall angle of size 24mm x 24mm x 2.4mm fixed to periphery of the wall and the above grid is suspended at every 1200mm c/c in both directions using 2.0mm thick GI Wire including cost and conveyance of all materials to site etc., for finished item of work as directed. Holding down clips to be used for fixing Thermocole sheets.

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Supply of Structural Steel Angles/Channels/Beams/ Square Bars for the month of July - 2024(Inclusive of 13.615% CP and OH)

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Supply and fixing 12mm thick window shutters with plain Cement bonded particle board (bison panel or equivalent) conforming to IS 14276 with alround U section of size 12x18mm x 12mm made from 0.60mm thick galvanised colour coated cold rolled steel profiles with necessary srews fixed at every 1foot (304.8mm) intervals, fixing to the existing angle iron frame along with the following MS Powder coated fittings of approved make and applying 1coat of primer, one coat of luppam and 2 coats of Synthetic enamel paints as per approved design including cost and conveyance of all materials to site, all labour charges etc., complete for finished Item of work as directed. a) 150mm tower bolts with 10mm dia shoot - 1No.s per leaf b) 125mm long grip handles - 1No. per leaf c) 250mm long window casements- 1No. per leaf d) 200mm to 225mm long T- hinges 2nos per leaf

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Supply, Fabrication and fixing of door frame made of Angle iron of size 40x40x 6mm with one coat of Red oxide grade-I primer with the following MS fittings (Excluding Cost of Bed Blocks)(The Steel Sections etc., required will have to be procured by the contractor only and Steel will not be issued by the department) 1). 6nos. M.S. Z type hold fasts made out of 15x3mm flat of 100mm long fixed in CC 1:2:4 bed blocks (150 x 100x 100mm) 2) 10mm dia tie rod at the bottom with necessary nuts at the ends of Each side 3). 1no.stopper hinge per leaf 75mm medium duty 4). 4 No.s 300mm long T-Hinges

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Supply and fixing of Cement Bonded Pre-laminated Particle Board single door shutter using 16MM Cement Bonded Pre-laminated Particle Board with all round section â??Uâ?? section size of 20mm x18mm x20mm made of 0.60mm thick galvanized pre-painted cold rolled steel profiles Cement Bonded Pre-laminated Particle Board with necessary screws fixed at every 1â??0â?? ( 304.8mm) intervals. The cost inclusive of MS Nickel / powder coated fittings and Including cost and conveyance of all materials at site labour charges etc., complete finished item of work - SINGLE SHUTTER as per Approved Make a). MS Nickel coated coated 250mm long aldrops 2 nos , b). MS powder coated 250mm long tower bolt with 10mm dia shoot- 1 nos, c). 2nos MS powder coated 125mm long grip handle, d). 1 noâ??s M.S. Powder coated Door stopper.

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Supply and fixing of Cement bonded Particle BOARD (conforming to IS 14862) door shutter with all-round style â??Uâ?? lipping size 15 x 18 x 15 mm made from 0.8mm thick powder coated cold rolled steel profiles with 16 mm thick Cement bonded Particle BOARD with necessary screws fixed at 1â??-0â?? interval including cost and conveyance of all materials at site and applying 1 coat of primer, 2 coats of luppum and 2 coats of synthetic enamel paint with following MS powder coated fittings as per approved design for finished item of work - SINGLE SHUTTER as per Approved Make a). MS Nickel coated coated 250mm long aldrops 2 nos , b). MS powder coated 250mm long tower bolt with 10mm dia shoot- 1 nos, c). 1no. MS powder coated 150mm long grip handle, d). 1nos. M.S. Powder coated Door stopper.

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Painting with two coats of Synthetic enamel paints of grade - II paints of Approved Make and Shade to Old Iron work - complete for finished item of work.

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Painting to wood work/ Plastered Surfaces with Two coats of synthetic enamel paints of grade II of Approved Make, shade- to old works - complete for finished item of work.

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Dismantling / Removing old Cement mortar plaster through Manual means

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Demolishing Plain Cement Concrete through Manual means and disposal of unserviceable materials within 100 metres lead - upto 15 cm thickness.

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Demolition of Brick / Stone masonry in Cement Mortar through Manual means including stacking of serviceable materials and disposal of unserviceable materials within 100mts lead.

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Construction of 450mm x 450mm and 450mm depth Inspection Chamber with CC 1:4:8 base of 150mm thick 40 mm Crushed Granite metal and 225 mm thick Brick masonary walls in CM 1:6 with fly ash bricks of size 225 x 100 x 60mm with 50kg/Sq. Cm Compressive strength and plastering with CM 1:4; 12mm thick including rendering the surfaces smooth both inside and outside and channelling to required slope including supply and fixing precast RCC 1:2:4 cover of 50mm thick and 600 X 600mm size with 20mm down size (65% of 20-10mm and 35% of 10-4.75mm) graded Crushed Granite metal, including earthwork excavation to the required depth etc; complete for finished item of work (but excluding cost of cement steel and its fabrication charges.)

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Erecting companys steel purlins, louvers, sag rods, rafters etc., with contractors tackle, derric, crane etc., complete

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Fabrication of structural steel components like purlins, louvers, sag rods, rafters etc., including all leads and lifts at site etc., with companys steel sections but with contractors welding rods, bolts, rivets and all contingencies, power charges, etc., complete as per drawings and instructions of the Engineer in charge.

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Roofing/side sheeting with corrugated G.I sheets 0.80mm thick fixed with 8mm dia G.I J bolts and nuts, with bitumen and G.I limpet washers filled with white lead, including fixing of wind ties as per the requirement etc., and including cost and conveyance of all materials etc., complete (with / without Ridges/ valley gutters) for finished Item of work as directed. ( Weight of GI Sheet is 6.66Kg/Sqm) (cost of wind ties and its fabrication charges are not included)

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Roofing/Side sheeting with A.C corrugated sheets 6mm thick including cost and conveyance of AC Sheets, 8mm dia G.I J bolts, GI washers, bitumen washers and labour charges including fixing of wind ties as per the requirement etc., complete (with /without Ridges / Valley gutters) for finished item of work (cost of wind ties and its fabrication charges are not included)

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Acrylic exterior emulsion Painting to Old walls 2 coats with Grade-II i.e., Ace or equivalent paint of Approved Make complete for finished Item of work For External Walls

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Oil bound Distempering to Old walls with 2 coats of Approved Make distemper complete for finished Item of work.

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;White washing to Old walls with Surya Cem / Equivalent Cem, two coats complete for finished item of work.

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Supplying and fixing 580 x 440mm Orissa pan white glazed W.C first quality ISI marked conforming to IS 2556 - part 3- 2004 with P or S trap

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Flooring with Non-skid Ceramic floor tiles of size 400 x 400 mm and thickness between 7-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs, set over base coat of cement mortar (1:6), 12 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per Sqm and jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost and conveyance of all materials, labour charges etc., complete for finished item of work, (But Excluding Cost of Cement )

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Flooring 40mm thick with CC1:2:4 using 20mm Down size ( 65% of 20-10mm and 35% of 10 - 4.75mm ) graded crushed granite metal of approved hard quality on existing concrete base, rendering smooth complete. ( But Excluding Cost of Cement )

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Flooring 30mm thick with CC 1:2:4 using 10mm size crushed granite metal of approved hard quality on existing concrete base, rendering smooth complete. ( But Excluding Cost of Cement )

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Plastering to Ceiling with cement mortar 1:3, 12mm thick ( But Excluding Cost of Cement )

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Plastering to brick / stone masonry with cement mortar 1:6, 20 mm thick in two coats including raking out of joints for walls only ( But Excluding Cost of Cement )

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Plastering to brick masonry with cement mortar 1:6, 12mm thick including raking out of joints ( But Excluding Cost of Cement )

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Flyash Brick masonry with bricks of size 225x100x60mm with 50kg/cm2 Compressive strength in C.M.1:6 for superstructure including scaffolding etc., (But Excluding Cost of Cement) complete.

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Cement Concrete 1:5:10 with 40 mm size Crushed Granite metal of approved hard quality in foundations or Plinth etc., Complete. (But Excluding Cost of Cement) - with concrete mixer

M and R works to NC C BCH DCH type quarters and shops at sector I RG I Area GDK;Earth work excavation for foundations and depositing on bank for all lifts and with an initial lead up to 50m including all operational, incidental, labour charges such as shoring, sheeting, planking, strutting, etc. complete for finished item of work as per SS - 20 B (APSS 308) - Ordinary Soil-Manual Means -Up to 3 m depth