Roads And Buildings Department Tender

Providing Road Safety Interventions;Supplying and installation of Hazard Markers/Delinators using M.S. angle of size 55x55x6 mm and 120cm high above ground level painted with two coats of black & white stripes of 15cm wide with first quality synthetic enamel paint over one coat of appropriate primer of approved brand,colour, with 30cm x 90cm Type ? XI of ASTMD 4956-09 High Intensity Prismatic Retro reflective sheeting of Yellow colour and confirming to IRC 67:2012 fixed over 3MM Alluminium Composite Material having minimum 0.30 mm thick Aluminium skin on both sides with standard supports consisting of alternately black and Yellow with black stripes in screen printing sloping downward at an angle of 45 degrees towards the side of the obstruction on which the traffic is to pass and buried into the ground in a trench of size 30cm x 30cm and 50cm depth filled with CC M-20 including cost and conveyance of all materials, equipment, machinery and labour with all leads and lifts, loading and un-loading charges necessary for successfull completion of the work on any road in division as directed by Engineer-in-Charge and conforming to IRC 67-2012 &MORT&H specification No.805 and approved drawings etc., complete for finished item of work.

Providing Road Safety Interventions;Providing and fixing Village name board size 600x800 mm made out of Type ? XI of ASTMD 4956-09 wide angle cube cornered micro Prismatic Retro reflective sheeting and confirming to IRC 67:2012 for full background of Green Colour & White Letters and fixed over 3MM Alluminium Composite Material sheet having minimum 0.30mm thick Aluminium skin on both sides with back side painted grey colour and fixed over back support frame of M.S angle 25x25x3mm all round and fixing with 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1 m from the ground level to the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of synthetic enamel paint Black and White colour with bands of 30cm of height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M-15 Concrete foundation of size 450x450x600mm including cost and conveyance of all materials ,equipment, machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by Engineer ?in-Charge.

Providing Road Safety Interventions;Providing and fixing of Cautionary / Warning sign boards of size 600mm equilateral triangle made out of Retro reflecting sheeting Type - III as per ASTM D4956-01 for full back ground of white colour and letters/logos done by screen printing in black colour and boarders by Red colour as per IRC:67-2001 and fixed over 4mm thick FRP sheet and painted back side with grey colour and fixed over back support frame of MS angle 25x25x3 mm all round and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1m from the ground level the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of synthetic enamel paint of every 30cm with Black & white colour. The signpost shall be firmly fixed with MS base angle 35x35x4mm in to the ground by 1:2:4 concrete foundation of size 450 x 450 x 600mm.

Providing Road Safety Interventions;Providing & fixing junction boards of size 1500 x 1200 mm made out of Type ? XI of ASTMD 4956-09 wide angle cube cornered micro Prismatic Retro Retro reflective sheeting Prismatic Retro reflective sheeting and confirming to IRC 67:2012 for full background of Green Colour & White Letters and fixed over 4MM Alluminium Composite Material sheet having minimum 0.5 mmthickAluminium skin on both sides with backside painted greycolour and fixed overback support frame of M.S angle 25x25x3mm all round and fixing with 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1 m from the ground level to the bottomof theboard. Thesignpost shouldbe paintedwith onecoat ofred oxidepaint and2coatsof syntheticenamelpaintBlackandWhite colourwith bandsof 30cmof height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M-15 Concrete foundation of size 450x450x600mm including cost and conveyance of all materials ,equipment, machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by Engineer -in-Charge.

Providing Road Safety Interventions;Supplying & fixing of Molded Shanks Raised Pavement Markers made of plastic body moulded from HIPS (HI-impact polysterene) or ABS or ASA(Acrylic strene Acrylonirite) and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall suppport a load of 16000 Kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No. RW/NH/33023/10-97-DO III, Dt: 11.06.1997. The height, width and length shall not exceed 50mm, 100mm and with minimum reflective area of 13 SqCm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks.(of diameter not less than 19 +/- 2 mm and height not less than 30 +/- 2mm) from the body is to be a minimum value of 700 Kgs. fixing will be by drilling holes on the road for the twin shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the Engineer-in-Charge

Providing Road Safety Interventions;Providing Rumble Strips in 6 transverse bar with Hot Applied Thermo-plastic compound with 5mm/7.5mm/15mm thick in multiple layers of 2.5mm thick each and 200mm/300mm width including reflectorising glass beads @ 250gms per sqm for top layer on Bituminous surface and top layer thickness of 2.5mm is exclusive of surface applied glass beads as per IRC : 35, the material should be of BERGER Company/ BERGER Equivalent/ Equivalent brand and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference The applied panel 7/8 number must be submitted for checking up the white index in the department lab In case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied products at site against the approved panel. In case of any major deviation, beyond acceptance limit, department reserve the right to cancel or reject the total supplied consignment of the said material and will compell the vendor has to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department). b) Luminance factor of the material should be in the range of 80-85% at 45 degree centigrade as per AASTHOM 249. c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS 3262, Part-1, 1989 and should pass at the range of 'O' degree centigrade to '-10' degree centigrade D) Adhesion : Strong E) Softening point: 102 degree centigrade F) Dried film finish : Smooth and uniform G) Night Vision: High as directed by the Engineer-in-Charge and confirming to IS: 164-1981 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-2015. The finished surface to be level, uniform and free from streaks and holes etc, complete for finished item of work (with all lifts and leads) (15 mm Thick)

Providing Road Safety Interventions;Supplying of hot applied thermoplastic road marking compound, 2.5 mm thick including reflectorising glass beads @ 250gms with Reflectorising Glass Beads on Bituminous Surface at 250 gms per sqmarea, thicknessof 2.5mm is exclusive of surface applied glass bead as per MORTH Section 803.4 and IRC: 35-2015, the material should satisfy the requirements as per MORTH specifications 803.4 and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference. The applied panel 7/8 number must be submitted for checking up the white index in the department lab. In case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied productsat site against the approved panel. In case of anymajor deviation, beyond acceptance limit, department reserve the right to cancel or reject the total supplied consignment of the said material and will compell the vendor has to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department). b) Luminance factor of the material should be in the range of 80-85% at 45 degree centigrade as per AASTHOM 249. c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS3262, Part-1, 1989 and should pass at the range of '0' degree centigrade to '-10' degree centigrade D) Adhesion:StrongE)Softeningpoint:102 degreecentigrade F)Dried filmfinish: Smoothanduniform G)Night Vision: High as directed by the Engineer-in-Charge and confirming to IS: 164-1961 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-2015 and MORTH Section 803.4