Military Engineer Services Tender

Supply only Integral waterproofing compound for waterproof plastering complete all as specified and directed.

M & L Providing roof treatment by priming the plastered roof surfaces with bituminous primer @ 0.3 Kg/Sqm and laying the APP modified water proofing membrane as perIS 16540-2017/ IS 16532-2017 mineral finish, 3 mm thick and weighing not less than 3.8 kg/sqm reinforced with non woven polyester /HMHDPEmatt black finished over compatible primer/bonding bitumen with 100 mm overlap after necessary preparation of surface complete as per manufacturer’s instructions with bituminous aluminium paint on top @ 0.1ltr/Sqm complete all as specified and directed..

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles including removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

M & L Brick work with using fly ash modular bricks straight or curved on plan exceeding 6 metre mean radius with old size bricks built in CM (1:6 ) complete all as specified and as directed.

M & L Rendering 15mm thick CM (1:3) on fair faces of brick work or concrete surfaces in wall/chajja or sunken floor with using WPC @3% by weight of cement or as per manufacturers instructions including finishing the surfaces even and smooth without using extra cement all as specified and directed.

M & L Rendering 10mm thick CM (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Dismantling of floor, hearth or wall tiles including cement mortar bedding (but not backing),removal servicable tiles to store including removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified an directed

M&L Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M & L Designer coloured glossy chequered cement concrete tiles of size 30cm x 30cm x 25mm thick in floor, set, jointed and pointed in neat cement slurry over and including 20 mm thick screed bed in CM (1:6) complete all as specified and as directed.

M & L for PCC (1:3:6) type C2 (using 40mm graded broken stone aggregate) as in sub base including demolition of existing concrete complete all as specified and as directed.

Dismantling existing interlocking tiles, paver block, removing rubbish off the premises and laying the same tiles/ blocks, 60mm/80mm thick, in floor/ pavement laid over and including 25mm thick sand cushioning laid dry to the profile including vibrating with surface vibrator after laying of tiles complete all as specified and as directed.

Excavation in post holes (or similar holes) each n.exc 0.5 cum, getting out in Hard/Dense soil, returning, filling in & ramming earth or broken rubbles mixed with earth around in layers n.exc 25 cm complete all as specified and directed.

M&L Providing PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in post holes complete all as specified and directed.

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semi-corrugated, etc. ) sheets in roof coverings complete all as specified and as directed..

S & F Pre-painted galvatume aluminium zince coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Dismantling of fillets, rails, posts, rafters, purlins, etc. under 40 sq.cm in section complete all as specified and as directed.

S & F Structural steel work Rolled sections as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connected plates confirming to Fe-410-W.Gde E-250 ,Quality ' A ' complete all as specified and directed.

S & F Structural steel work Rolled hollow sections as in stanctions/ vertical column fixed with base plates or other connecting plates etc confirming to Fe-410- W (Gde-E-250) quality-A etc complete all as specified and as directed.

S & F MS plates (plain or chequered) 8mm to 12 mm thick cut to shape forming holes and welded to truss and verticle post as base plate confirming to Fe-410- W(Gde-E-250) quality-A, all as required complete all as specified and as directed.

S & F Mild steel screw bolts (machine made), diameter of shank 16 to 20 mm, with hexagonal or square heads at one end and screwed the other, or screwed both ends, Each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10 cm and n exc 15 cm long all as specified and directed.

S & F Mild steel screw bolts (machine made), diameter of shank 16 to 20 mm, with hexagonal or square heads at one end and screwed the other, or screwed both ends, Each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 22.5 cm and n exc 45 cm long all as specified and directed.

M & L Preparation of new or previously untreated steel or Iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over red oxide, zinc chrome primer complete all as specified and as directed.

Dismantling of wall/ceiling board of any description and any thickness including cover fillets and frame work ete all as specified and directed.

S & F GI frame work Size of grid 605 x 605mm for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/inteRmediate channel 0.9 mm thick having two equal flanges of 15 mm Each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm Each with lips of 10.5 mm fixed to the inteRmediate channel with connecting clips across the inteRmediate channel at 457 mm centre to centre and Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

M & L Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified.

M & L Preparation of new gypsum board ceiling surfaces and applying two coats of OBD (oil emulsion) over a coat of alkali resistant primer over plaster of paris putty of 1 mm thickness on ceiling surfaces complete all as specified and as directed.

S & F in repairs push pull or manual type Steel rolling shutters of laths thickness 1.25mm with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated complete all as specified and directed.

S & F in repairs gear operated type Steel rolling shutters with bevel gear box and crank handle of laths thickness 1.25mm with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated complete all as specified and directed.

S & F in repairs gear operated type Steel rolling shutters with with chain wheel and hand chain of laths thickness 1.25mm with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated complete all as specified and directed.

S & F in repairs Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

S & F in repairs Ball bearing for rolling shutters complete all as specified and directed.