National Highways Authority Of India Tender

Speed Limit board (60cm Circular Triangle)

Chevron Board (60cm x 50cm)

Bollards

Bus Stop sign Board/ Village Information (80cmx60cm)

Providing and laying of hot applied Thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes etc complete as per MORT&H Specification no. 803.

Centre Line

Edge Line

STOP Lines and STOP letters

Pedestrain crossing

Speed Hump (triangular block making as per IRC:035-2015 & chequer block making as per IRC:035-2015)

Transverse bar marking 5.0mm thick

Transverse bar marking 7.5mm thick

Transverse bar marking 10mm thick

Speed Hump

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 to 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects

Road Markers/ Road Stud with Lens Reflector Providing and fixing reflective road studs of ‘category A’ Raised pavement markers made out of poly carbonate / methyl methercrylate/ABS moulded body confirming to ASTM D788 and reflective panels with micro prismatic lens capable o providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORT&H circular No. RW/NH.33023/10/97-DO.III dt. 11.06.97. The height, width and length shall not be less than 15mm, 90mm, and 100mm and with minimum reflective area of 13Sqcm on each side and the slope to the base shall be 35+/- degree. Each reflector shall have a CIL not less than values specified in Table 2 of said MORTH Circular. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum 500Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer’s recommendation and complete as directed by Engineer. The Marker shall support a load of 13635 Kg tested in accordance with ASTM D4280 and confirming to IRC:35 – 2015 guidelines and MORT&H specification 804 etc., complete.

Supply and fixing of Solar LED Blinker RED/YELLOW Colour 300mm dia Polycarbonate dome 5mm LED 176 Nos led high brightness led of Upto 1000 mtr Visibility 50,000 hour working life,18Ah SMF battery, SCC 12v 5A with all protection, 40Wp Solar Panel 24Hhr Blinking with all accessories, mounted 6 mtr, 100mm dia class B MS Painted Pole with all accessories. (and Installation of Solar binker with cement concrete foundation with a depth of 3 mtr for 6mtr pole.

Junction Improvement

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 to 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects