National Highways Authority Of India Tender

a). Speed Limit (40Km,60KM) (60cm Circular)

ii. Informatory Signs

a). Accident Zone (90cm Equilateral Triangle)

b). Restricted End (60cm Circular)

Road Markings with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Pavement marking with hot applied reflectorised thermoplastic paints.Providing and laying of hot applied thermoplastic compound 15.00 mm thick including reflectorising glass beads @ 1500 gms per sqm area, thickness of 15.00 mm is exclusive of surface applied glass beads as per IRC:35-2015 .The finished surface to be level, uniform and free from streaks and holes. . The colour of the compound shall be white or yellow (IS colour No, 356) as specified in the drawings or as directed by the Engineer and MoRTH Specifications Clause 803

Road Markers/ Road Stud with Lens Reflector Providing and fixing reflective road studs of ‘category A’ Raised pavement markers made out of poly carbonate / methyl methercrylate/ABS moulded body confirming to ASTM D788 and reflective panels with micro prismatic lens capable o providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORT&H circular No. RW/NH.33023/10/97-DO.III dt. 11.06.97. The height, width and length shall not be less than 15mm, 90mm, and 100mm and with minimum reflective area of 13Sqcm on each side and the slope to the base shall be 35+/- degree. Each reflector shall have a CIL not less than values specified in Table 2 of said MORTH Circular. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum 500Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer’s recommendation and complete as directed by Engineer. The Marker shall support a load of 13635 Kg tested in accordance with ASTM D4280 and confirming to IRC:35 – 2015 guidelines and MORT&H specification 804 etc., complete.

Supply and Installtion of Double arm street lights - Supply of 150W - 2no's of LED High Bay Flood lights and Supply, Erection of 8m Free Standing Double Arm Bracket 8 sided Octogonally continuosly tapered structured pole with base plate of size 300 x 300 x 12mm as per IS-875 with specifications of Bottom Pole Dia - 130mm, Top Pole Dia - 70mm, Thickness of pole - 3mm, The pole should be not dip galvanized confirming to BESN ISO-1461 with thickness of 65 Micron

Sub Total (1)

Hotspot ID - HS03524

Retro-Reflectorised Traffic Signs (Without definition Board) Providing and Erecting of Retro - Reflectorised Cautionary, Mandatory and Informatry signs (with/ without definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67:2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25 mm x 25 mm x 3 mm Mild Steel angle and supported on Mild Steel Angle Post 75x75x6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sig board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement Concrete 45cmx45cmx60cm size including cost and conveyance of all materials, equipment, Machinery and Labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro – Reflectorised sheet shall consist of minimum coefficient of Retro-reflection as per Table6.6 of IRC: 67 -2012. Th retro – reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC:67-2012. (as per MORT&H Specification No.801)

i. Mandatory/Regulatory Signs

a). Speed Limit (40Km,60KM) (60cm Circular)

ii. Informatory Signs

a). Accident Zone (90cm Equilateral Triangle)

b). Restricted End (60cm Circular)

Road Markings with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Pavement marking with hot applied reflectorised thermoplastic paints.Providing and laying of hot applied thermoplastic compound 15.00 mm thick including reflectorising glass beads @ 1500 gms per sqm area, thickness of 15.00 mm is exclusive of surface applied glass beads as per IRC:35-2015 .The finished surface to be level, uniform and free from streaks and holes. . The colour of the compound shall be white or yellow (IS colour No, 356) as specified in the drawings or as directed by the Engineer and MoRTH Specifications Clause 803

Road Markers/ Road Stud with Lens Reflector Providing and fixing reflective road studs of ‘category A’ Raised pavement markers made out of poly carbonate / methyl methercrylate/ABS moulded body confirming to ASTM D788 and reflective panels with micro prismatic lens capable o providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORT&H circular No. RW/NH.33023/10/97-DO.III dt. 11.06.97. The height, width and length shall not be less than 15mm, 90mm, and 100mm and with minimum reflective area of 13Sqcm on each side and the slope to the base shall be 35+/- degree. Each reflector shall have a CIL not less than values specified in Table 2 of said MORTH Circular. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum 500Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer’s recommendation and complete as directed by Engineer. The Marker shall support a load of 13635 Kg tested in accordance with ASTM D4280 and confirming to IRC:35 – 2015 guidelines and MORT&H specification 804 etc., complete.

Supply and Installtion of Double arm street lights - Supply of 150W - 2no's of LED High Bay Flood lights and Supply, Erection of 8m Free Standing Double Arm Bracket 8 sided Octogonally continuosly tapered structured pole with base plate of size 300 x 300 x 12mm as per IS-875 with specifications of Bottom Pole Dia - 130mm, Top Pole Dia - 70mm, Thickness of pole - 3mm, The pole should be not dip galvanized confirming to BESN ISO-1461 with thickness of 65 Micron

Sub Total (2)

Hotspot ID - HS03459

Retro-Reflectorised Traffic Signs (Without definition Board) Providing and Erecting of Retro - Reflectorised Cautionary, Mandatory and Informatry signs (with/ without definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67:2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25 mm x 25 mm x 3 mm Mild Steel angle and supported on Mild Steel Angle Post 75x75x6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sig board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement Concrete 45cmx45cmx60cm size including cost and conveyance of all materials, equipment, Machinery and Labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro – Reflectorised sheet shall consist of minimum coefficient of Retro-reflection as per Table6.6 of IRC: 67 -2012. Th retro – reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC:67-2012. (as per MORT&H Specification No.801)

i. Mandatory/Regulatory Signs

a). Speed Limit (40Km,60KM) (60cm Circular)

ii. Informatory Signs

a). Accident Zone (90cm Equilateral Triangle)

b). Restricted End (60cm Circular)

Road Markers/ Road Stud with Lens Reflector Providing and fixing reflective road studs of ‘category A’ Raised pavement markers made out of poly carbonate / methyl methercrylate/ABS moulded body confirming to ASTM D788 and reflective panels with micro prismatic lens capable o providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORT&H circular No. RW/NH.33023/10/97-DO.III dt. 11.06.97. The height, width and length shall not be less than 15mm, 90mm, and 100mm and with minimum reflective area of 13Sqcm on each side and the slope to the base shall be 35+/- degree. Each reflector shall have a CIL not less than values specified in Table 2 of said MORTH Circular. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum 500Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer’s recommendation and complete as directed by Engineer. The Marker shall support a load of 13635 Kg tested in accordance with ASTM D4280 and confirming to IRC:35 – 2015 guidelines and MORT&H specification 804 etc., complete.

Supply and Installtion of Double arm street lights - Supply of 150W - 2no's of LED High Bay Flood lights and Supply, Erection of 8m Free Standing Double Arm Bracket 8 sided Octogonally continuosly tapered structured pole with base plate of size 300 x 300 x 12mm as per IS-875 with specifications of Bottom Pole Dia - 130mm, Top Pole Dia - 70mm, Thickness of pole - 3mm, The pole should be not dip galvanized confirming to BESN ISO-1461 with thickness of 65 Micron

Sub Total (3)

Hotspot ID - HS03454

Retro-Reflectorised Traffic Signs (Without definition Board) Providing and Erecting of Retro - Reflectorised Cautionary, Mandatory and Informatry signs (with/ without definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67:2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25 mm x 25 mm x 3 mm Mild Steel angle and supported on Mild Steel Angle Post 75x75x6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sig board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement Concrete 45cmx45cmx60cm size including cost and conveyance of all materials, equipment, Machinery and Labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro – Reflectorised sheet shall consist of minimum coefficient of Retro-reflection as per Table6.6 of IRC: 67 -2012. Th retro – reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC:67-2012. (as per MORT&H Specification No.801)

i. Mandatory/Regulatory Signs

a). Speed Limit (40Km,60KM) (60cm Circular)

ii. Informatory Signs

a). Accident Zone (90cm Equilateral Triangle)

b). Restricted End (60cm Circular)

Road Markers/ Road Stud with Lens Reflector Providing and fixing reflective road studs of ‘category A’ Raised pavement markers made out of poly carbonate / methyl methercrylate/ABS moulded body confirming to ASTM D788 and reflective panels with micro prismatic lens capable o providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORT&H circular No. RW/NH.33023/10/97-DO.III dt. 11.06.97. The height, width and length shall not be less than 15mm, 90mm, and 100mm and with minimum reflective area of 13Sqcm on each side and the slope to the base shall be 35+/- degree. Each reflector shall have a CIL not less than values specified in Table 2 of said MORTH Circular. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum 500Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer’s recommendation and complete as directed by Engineer. The Marker shall support a load of 13635 Kg tested in accordance with ASTM D4280 and confirming to IRC:35 – 2015 guidelines and MORT&H specification 804 etc., complete.

Supply and Installtion of Double arm street lights - Supply of 150W - 2no's of LED High Bay Flood lights and Supply, Erection of 8m Free Standing Double Arm Bracket 8 sided Octogonally continuosly tapered structured pole with base plate of size 300 x 300 x 12mm as per IS-875 with specifications of Bottom Pole Dia - 130mm, Top Pole Dia - 70mm, Thickness of pole - 3mm, The pole should be not dip galvanized confirming to BESN ISO-1461 with thickness of 65 Micron

Sub Total (4)

Hotspot ID - HS03458

Retro-Reflectorised Traffic Signs (Without definition Board) Providing and Erecting of Retro - Reflectorised Cautionary, Mandatory and Informatry signs (with/ without definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67:2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25 mm x 25 mm x 3 mm Mild Steel angle and supported on Mild Steel Angle Post 75x75x6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sig board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement Concrete 45cmx45cmx60cm size including cost and conveyance of all materials, equipment, Machinery and Labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro – Reflectorised sheet shall consist of minimum coefficient of Retro-reflection as per Table6.6 of IRC: 67 -2012. Th retro – reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC:67-2012. (as per MORT&H Specification No.801)

i. Mandatory/Regulatory Signs

a). Speed Limit (40Km,60KM) (60cm Circular)

ii. Informatory Signs

a). Accident Zone (90cm Equilateral Triangle)

b). Restricted End (60cm Circular)

Road Markers/ Road Stud with Lens Reflector Providing and fixing reflective road studs of ‘category A’ Raised pavement markers made out of poly carbonate / methyl methercrylate/ABS moulded body confirming to ASTM D788 and reflective panels with micro prismatic lens capable o providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORT&H circular No. RW/NH.33023/10/97-DO.III dt. 11.06.97. The height, width and length shall not be less than 15mm, 90mm, and 100mm and with minimum reflective area of 13Sqcm on each side and the slope to the base shall be 35+/- degree. Each reflector shall have a CIL not less than values specified in Table 2 of said MORTH Circular. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum 500Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer’s recommendation and complete as directed by Engineer. The Marker shall support a load of 13635 Kg tested in accordance with ASTM D4280 and confirming to IRC:35 – 2015 guidelines and MORT&H specification 804 etc., complete.

Supply and Installtion of Double arm street lights - Supply of 150W - 2no's of LED High Bay Flood lights and Supply, Erection of 8m Free Standing Double Arm Bracket 8 sided Octogonally continuosly tapered structured pole with base plate of size 300 x 300 x 12mm as per IS-875 with specifications of Bottom Pole Dia - 130mm, Top Pole Dia - 70mm, Thickness of pole - 3mm, The pole should be not dip galvanized confirming to BESN ISO-1461 with thickness of 65 Micron

Sub Total (4)

GRAND TOTAL (1+2)