National Highways Authority Of India Tender

Solar Blinkers - Blinking Variable Signal 300mm light Red or Amber Bib X Model Light (Blue, White & Red)L Pole Bi 5'', Height 25 Feet, L Model Top 9 Feet Yellow Coating Solar Panel, 150W Solar Charge Controller/ Battery Box / Maintenance free Battery 12V 60-100Ah Lithium Battery and as per instructions by NHAI

Total Amount (Rs.)

Description

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom. - Tack Coat on Granular surfaces treated with primer

Dense Graded Bituminous Macadam-II (Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects.) (50-75 mm)

Providing and laying of hot applied Thermoplastic compound 2.5mm thick including reflectorizing glass beads @ 250gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes etc complete as per MoRT&H Specification No.803 (Road marking)

Providing and erecting of Retro-Reflectorized Cautionary, Mandatory and Informatory signs (with definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-XI standards of IRC-67:2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mm x 3mm Mild Steel angle and supported on a mild steel angle post 75x75x6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level The sign post should be painted as per IRC-67:2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro-Reflectro sheet shall consist of minimum coefficient of Retro-Reflection as per Table 6.6 of IRC-67:2012. The retro-reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC-67:2012 (as per MoRT&H Specification No.801)

(i) 900mm Equilateral triangular - Road Hump Ahead

Providing and fixing reflective road studs of 'Category A' Raised pavement markers made out of poly carbonate / methyl methacrylate / ABS moulded body confirming to ASTM D 788 and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values confirming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MoRTH circular No RW/NH.33023/10/97-DO.III dt. 11.06.97. The height, width and length shall not be less than 15mm, 90mm and 100mm and with minimum reflective area of 13 Sq.cm on each side and the slope to the base shall be 35 + / - 5 degree. Each reflector shall have a CIL not less than values specified in Table 2 of said MoRTH circular. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 + / - 2mm and height not less than 30 + / - 2mm) from the body is to be a minimum value of 500 Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280 and confirming to IRC:35-2015 guidelines and MoRT&H specification 804 etc., CompleteRoad (studs)

Supply and Installation of Single arm Solar street lights - Supply of 1x 80w (+/-5w) Stand alone Solar Streetlight System having 2 days backup and Suitable for dimming a) Streetlight Luminaire shall have minimum 12,500 Lumens System output, greater than 160 Lumens Per watt system efficiency, IP66 & IK10 Protection, luminaire made Corrosion proof coated Pressure Diecast aluminum Housing and individual lens for each LED embedded on PC cover. 70,000 burning hours life - 1no b) Solar Panel of 300 - 340Wp Mono- Crystalline 36V with excellent aging resistance and UV endurance to withstand harsh environment environmentally sealed to IP67- 1no c) The Batteries using in the system shall be of 25.6V 60Ah, 1536Whr Maintenance free Lithium Pherro Phospate battery having minimum 2000 cycles life - 1no d) The Charge controller using in the system shall be 400Wp MPPT type Programmable and dimmable via blue tooth app at site, 93% efficiency, built in protection of Battery Reverse Polarity, Panel Reverse Polarity, Panel Reverse Current, Surge Protection at PV input, Battery Over Voltage, Load short circuit and fuse protection. The Charge Controller shall be kept inside the Pole Junction box e) Supply installation testing and commissioning of above mentioned Solar system on 9 metres height hot dip galvanized Octagonal Pole made of BSEN10025 GI with min top 90mm and bottom 190mm dia made of min 3mm sheet thickness, Base Plate 350x350x20mm, Mounting Brackets for holding Solar panels at the top, Galvanized Battery mounting box and single arm bracket with all accessories for fixing luminaires as per structural stability design f) Foundation 500mm x 500mm x 800mm below soil level and 300mm above ground level of M25 Grade for Single arm bracket and as per instructions by NHAI

Supplying of Solar Raised Pavement Markers made of polycarbonate molded body, solar powered, LED self- illumination in active mode, 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode. The product shall support a load of 13635 kg tested in accordance to MORTH and ASTM D 4280 Type H. The product should be resistant water ingress according to IP 65 standards with IS 12063:1987 Category 2 and should withstand temperatures to in the range of -7 C to 70 C. Flashing rate and color of lighting is to be provided as per requirement. There should be minimum current losses of less than 20 micro-amperes in sleep-charging mode to enhance product life and single charge should provide for a minimum autonomy of 50 hours. The height, width and length shall not be less than 10 mm x 100 mm x 100 mm. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer. Warranty Certificate and test reports confirming to compressive strength as per MORTH circular shall be obtained from the manufacturer and submitted to the engineer in charge. Two Years Warranty Certificate for Solar RPM for the quantity installed and a certified copy of test reports from an independent test laboratory conforming to water ingress shall be obtained from the Manufacturer by the contractor and submitted to the engineer-in-charge.

Solar Blinkers - Blinking Variable Signal 300mm light Red or Amber Bib X Model Light (Blue, White & Red)L Pole Bi 5'', Height 25 Feet, L Model Top 9 Feet Yellow Coating Solar Panel, 150W Solar Charge Controller/ Battery Box / Maintenance free Battery 12V 60-100Ah Lithium Battery and as per instructions by NHAI

Total Amount (Rs.)

Description

Providing and laying of hot applied Thermoplastic compound 2.5mm thick including reflectorizing glass beads @ 250gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes etc complete as per MoRT&H Specification No.803 (Road marking)

Supply and Installtion of Double arm Solar street lights - Supply of 2x 80w (+/-5w) Stand alone Solar Streetlight System having 2 days backup and Suitable for dimming a) Streetlight Luminaire shall have minimum 12,500 Lumens System output, greater than 160 Lumens Per watt system efficiency, IP66 & IK10 Protection, luminaire made Corrosion proof coated Pressure Diecast aluminum Housing and individual lens for each LED embedded on PC cover. 75,000 burning hours life - 1no b) Solar Panel of 300 - 340Wp Mono- Crystalline 36V with excellent aging resistance and UV endurance to withstand harsh environment environmentally sealed to IP67- 1no c) The Batteries using in the system shall be of 25.6V 60Ah, 1536Whr Maintenance free Lithium Pherro Phospate battery having minimum 2000 cycles life - 1no d) The Charge controller using in the system shall be 400Wp MPPT type Programmable and dimmable via blue tooth app at site, 93% efficiency, built in protection of Battery Reverse Polarity, Panel Reverse Polarity, Panel Reverse Current, Surge Protection at PV input, Battery Over Voltage, Load short circuit and fuse protection. The Charge Controller shall be kept inside the Pole Junction box e) Supply installation testing and commissioning of above mentioned Solar system on 9 metres height hot dip galvanized Octagonal Pole made of BSEN10025 GI with min top 90mm and bottom 190mm dia made of min 3mm sheet thickness, Base Plate 320x320x20mm, Mounting Brackets for holding Solar panels at the top, Galvanized Battery mounting box and Double arm bracket with all accessories for fixing luminaires as per structural stability design f) Foundation 500mm x 500mm x 1000mm below soil level and 300mm above ground level of M25 Grade and as per instructions by NHAI

Supplying of Solar Raised Pavement Markers made of polycarbonate molded body, solar powered, LED self- illumination in active mode, 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode. The product shall support a load of 13635 kg tested in accordance to MORTH and ASTM D 4280 Type H. The product should be resistant water ingress according to IP 65 standards with IS 12063:1987 Category 2 and should withstand temperatures to in the range of -7 C to 70 C. Flashing rate and color of lighting is to be provided as per requirement. There should be minimum current losses of less than 20 micro-amperes in sleep-charging mode to enhance product life and single charge should provide for a minimum autonomy of 50 hours. The height, width and length shall not be less than 10 mm x 100 mm x 100 mm. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer. Warranty Certificate and test reports confirming to compressive strength as per MORTH circular shall be obtained from the manufacturer and submitted to the engineer in charge. Two Years Warranty Certificate for Solar RPM for the quantity installed and a certified copy of test reports from an independent test laboratory conforming to water ingress shall be obtained from the Manufacturer by the contractor and submitted to the engineer-in-charge.

Solar Blinkers - Blinking Variable Signal 300mm light Red or Amber Bib X Model Light (Blue, White & Red)L Pole Bi 5'', Height 25 Feet, L Model Top 9 Feet Yellow Coating Solar Panel, 150W Solar Charge Controller/ Battery Box / Maintenance free Battery 12V 60-100Ah Lithium Battery and as per instructions by NHAI

Total Amount (Rs.)

Description

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom. - Tack Coat on Granular surfaces treated with primer

Dense Graded Bituminous Macadam-II (Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects.) (50-75 mm)

Providing and laying of hot applied Thermoplastic compound 2.5mm thick including reflectorizing glass beads @ 250gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes etc complete as per MoRT&H Specification No.803 (Road marking)

Providing and erecting of Retro-Reflectorized Cautionary, Mandatory and Informatory signs (with definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-XI standards of IRC-67:2012 and ASTM D 4956-09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mm x 3mm Mild Steel angle and supported on a mild steel angle post 75x75x6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level The sign post should be painted as per IRC-67:2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro-Reflectro sheet shall consist of minimum coefficient of Retro-Reflection as per Table 6.6 of IRC-67:2012. The retro-reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC-67:2012 (as per MoRT&H Specification No.801)

(i) 900mm Equilateral triangular - Road Hump Ahead

Providing and fixing reflective road studs of 'Category A' Raised pavement markers made out of poly carbonate / methyl methacrylate / ABS moulded body confirming to ASTM D 788 and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values confirming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MoRTH circular No RW/NH.33023/10/97-DO.III dt. 11.06.97. The height, width and length shall not be less than 15mm, 90mm and 100mm and with minimum reflective area of 13 Sq.cm on each side and the slope to the base shall be 35 + / - 5 degree. Each reflector shall have a CIL not less than values specified in Table 2 of said MoRTH circular. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 + / - 2mm and height not less than 30 + / - 2mm) from the body is to be a minimum value of 500 Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280 and confirming to IRC:35-2015 guidelines and MoRT&H specification 804 etc., CompleteRoad (studs)

Supply and Installation of Single arm Solar street lights - Supply of 1x 80w (+/-5w) Stand alone Solar Streetlight System having 2 days backup and Suitable for dimming a) Streetlight Luminaire shall have minimum 12,500 Lumens System output, greater than 160 Lumens Per watt system efficiency, IP66 & IK10 Protection, luminaire made Corrosion proof coated Pressure Diecast aluminum Housing and individual lens for each LED embedded on PC cover. 70,000 burning hours life - 1no b) Solar Panel of 300 - 340Wp Mono- Crystalline 36V with excellent aging resistance and UV endurance to withstand harsh environment environmentally sealed to IP67- 1no c) The Batteries using in the system shall be of 25.6V 60Ah, 1536Whr Maintenance free Lithium Pherro Phospate battery having minimum 2000 cycles life - 1no d) The Charge controller using in the system shall be 400Wp MPPT type Programmable and dimmable via blue tooth app at site, 93% efficiency, built in protection of Battery Reverse Polarity, Panel Reverse Polarity, Panel Reverse Current, Surge Protection at PV input, Battery Over Voltage, Load short circuit and fuse protection. The Charge Controller shall be kept inside the Pole Junction box e) Supply installation testing and commissioning of above mentioned Solar system on 9 metres height hot dip galvanized Octagonal Pole made of BSEN10025 GI with min top 90mm and bottom 190mm dia made of min 3mm sheet thickness, Base Plate 350x350x20mm, Mounting Brackets for holding Solar panels at the top, Galvanized Battery mounting box and single arm bracket with all accessories for fixing luminaires as per structural stability design f) Foundation 500mm x 500mm x 800mm below soil level and 300mm above ground level of M25 Grade for Single arm bracket and as per instructions by NHAI

Supplying of Solar Raised Pavement Markers made of polycarbonate molded body, solar powered, LED self- illumination in active mode, 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode. The product shall support a load of 13635 kg tested in accordance to MORTH and ASTM D 4280 Type H. The product should be resistant water ingress according to IP 65 standards with IS 12063:1987 Category 2 and should withstand temperatures to in the range of -7 C to 70 C. Flashing rate and color of lighting is to be provided as per requirement. There should be minimum current losses of less than 20 micro-amperes in sleep-charging mode to enhance product life and single charge should provide for a minimum autonomy of 50 hours. The height, width and length shall not be less than 10 mm x 100 mm x 100 mm. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer. Warranty Certificate and test reports confirming to compressive strength as per MORTH circular shall be obtained from the manufacturer and submitted to the engineer in charge. Two Years Warranty Certificate for Solar RPM for the quantity installed and a certified copy of test reports from an independent test laboratory conforming to water ingress shall be obtained from the Manufacturer by the contractor and submitted to the engineer-in-charge.

Solar Blinkers - Blinking Variable Signal 300mm light Red or Amber Bib X Model Light (Blue, White & Red)L Pole Bi 5'', Height 25 Feet, L Model Top 9 Feet Yellow Coating Solar Panel, 150W Solar Charge Controller/ Battery Box / Maintenance free Battery 12V 60-100Ah Lithium Battery and as per instructions by NHAI

Total Amount (Rs.)

Grand Total (Rs.)